steel window Tenders in Rajasthan

1
Military Engineer Services - Rajasthan

40930245 comprehensive maintenance contract for attending day to day b / r and e / m complaints for offers / jco / or md accn at nagtalao under ge banar.; 1 water supply and sanitarydisconnecting existing tanks cap exc 250 ltr but nexc500 ltrs , setting aside ( or lowering if required ) for repairs, cleaning, etc. and hoisting if required, reconnecting and re fixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified. 2 disconnecting existing tanks cap exc 500 ltr but nexc 1000 ltrs , setting aside ( or lowering if required ) for repairs, cleaning, etc. and hoisting if required, reconnecting and re fixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified. 3 s&f in repairs toilet paper holder with flat recessed type stainless steel complete all as specified. 4 taking down cement plaster from stone masonry walls etc & m&l for15 mm thick rendering in cm 1:6 finished even & smooth complete all as specified. 5 taking down cement plaster from rcc chajja, fascia, ceilingetc & m&l for10 mm thick rendering in cm 1:4 finished even & smooth as in patches n. exc 3 sqm eachcomplete all as specified. 6 m&l for two coat of obd on newly plastered / unplastered surfaces over one coat of wall care putty on wall & including preparation complete all as specified. 7 m&l for preperartion ofnewly plastered surfaces of walland applying three coat of white wash complete all as specified. 8 preparation of new plastered / unplastered surfaces of wall & applying two coat ofcement base paintcomplete all as specified. 9 demolition of floor, hearth or wall tiling including cement mortar bedding ( but not backing ) complete all as specified. 10 demolition of cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level ) complete all as specified. 11 m&l for 25 mm thick cement concrete type b 1 1:2:4 ( using 20mm graded crushed stone aggregate ) to receive floor finishes etc complete all as specified. 12 m&l for coloured glazed ceramic tiles 300mmx450mmx6mmthick over and including 15mm thick rendering in cm ( 1:6 ) set and jointed in neat cement slurry and pointed with colour cement to match on vertical surfaces as in dado complete all as specified. 13 m&l for coloured non skid ceramic tiles 400mmx400mmx6 7 mm thick in floor etc set jointed and pointed in white or coloured cement to match as in floors overand including 15mm thick screed bed in cm ( 1:6 ) complete all as specified. 14 m&l for 15 17 mm thick granite ( of any type ) machine cut in cooking plateform laid over 10mm thick screed bed in cement mortar ( 1:4 ) and joined with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including polishing complete all as specified. 15 s & f in repairs cp bib cock 15mm bore complete all as specified. 16 m & l in repair15 mm stop valve ( concealed ) cromium plated, screwed down, high pressure with crutch or butterfly handle screwed for iron pipe or for unions and fixed complete all as specified. 17 m & l in repair 20 mm gate valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed for iron pipe or for unionscomplete all as specified. 18 m & l in repair 25 mm gate valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed for iron pipe or for unions complete all as specified. 19 s &f in repairs 15mm bore stop / angle valve of copper alloy, cp with flangecomplete all as specified. 20 s &f in repairspillar cock chromium plated fancy type 15 mm borecomplete all as specified. 21 s &f in repairs central hole basin mixer ( basin mixer ) brass chromium plated fancy type 15 mm bore complete all as specified. 22 s &f in repairs mixing valve ( wall mixer ) 3 in 1 with flexible tube & hand shower complete chromium plated fancy type 15 mm bore complete all as specified. 23 s &f in repairs pvc connection15mm bore of length 450 mm complete all as specified. 24 s &f in repairs pvc connection 15mm bore of length 600 mm complete all as specified. 25 s &f in repairspvcwaste pipe 32 40 mm size for wash hand basin / steel sinks etc complete all as specified. 26 s &f in repairs pvc flushing cistern 10 ltr cap dual flush typecomplete all as specified. 27 s &f in repairs cp waste coupling40 mm size with rubber gasketetcfor ss sink complete all as specified. 28 s &f in repairs cp waste coupling 32 mm sizewith rubber gasket etcfor whb etc complete all as specified. 29 s&f in repair fancy type chromium plated shower roses 125mm size with arm, with or without swivel joints, 15mm bore, including fixing to steel pipe or union complete all as specified. 30 s &f in repairs ptmt body ball cock / float valve 15 / 20 mm bore with epoxy coated aluminum rod & hdpe ball complete all as specified . 31 s &f in repairs ptmt body ball cock / float valve 25 mm bore with epoxy coated aluminum rod & hdpe ball complete all as specified. 32 s &f in repairs hdpe flush pipe 32 mm dia of flush cistern to wc completeall as specified. 33 s &f in repairsginipple 20 mm bore, 75mm long for tank connection complete all as specified. 34 s&fginipple 25 mm bore, 75mm long for tank connection complete all as specified. 35 s &f in repairs health foucet with 1200mm longflexiblemild steel tube, 15 mm dia with wall hookandcomplete all as specified. 36 s &f in repairs cp body hygeine wash jet spray assembly incl flexible pvc pipe complete all as specified. 37 s &f in repairs two way angle cock 15 mm bore cp complete all as specified. 38 s &f in repairs two way bib cock 15 mm bore cp fancy type complete all as specified. 39 s&f in repairs 600mmx450mm bevelled edge mirror of selected quality glass 5.5 mm thick, mounted on 6mm thick ac / pvc building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. 40 s &f in repairs aluminium anodisedtubular towel rail, 20mm dia, d type, 60cm long between flanges all as per sample complete all as specified. 41 s &f in repairs shelf of ptmt fixed with and including chromium plated brass screws and wooden / plastic cleats ( minimum weight 300gms ) complete all as specified. 42 s &f in repairssheet glass shelf assembly consisting of 6 8 mm thick sheet glass shelf 10 15cm wide with chromium plated bracket guard and railing 60cm long complete all as specified. 43 s &f in repairs plastic water closet seat cover, white, closed pattern with flat bottom, and cover with mild steel chromium plated or aluminised hinging device complete all as specified. 44 s &f in repairs cp grating 100 mm dia with or without hole ( for waste pipe ) 100 mm dia complete all as specified. 45 s &f in repairs vitreous china wash hand basin size 550x400 mm sizewith pedestal and a pair of brackets, waste pipe, waste coupling complete all as specified. 46 s &f in repairs vitreous china wash hand basin size 550x400 mm size with a pair of brackets, waste pipe, waste coupling complete all as specified. 47 s &f in repairs vitreous china squatting pan, ‘orissa’ pattern, size 580x440 mm white, with integral foot rests complete all as specified. 48 s &f in repairs stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen with plug, washers waste pipe, cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified. 49 s&f in repairs sinks made of stainless steel lmm thick kitchen with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. 50 s &f in repair of 15 mm bore gi tubing medium grade including fittings as elbow., socket , nipple etc complete all as specified. 51 s&f in repair of 20 mm bore gi tubing medium grade including fittings as elbow., socket , nipple etc complete all as specified. 52 s & f in repair 25 mm bore gi tubing medium grade including fittings complete all as specified. 53 s &f in repairs sink cock , cromium plated 15 mm bore complete all as specified. 54 attending complaints of leaking / unservicable , low level flushing cistern, pvc or chinaware for making it fully functtionl and leak proof by repacement the defective parts such as rubber washers , pvc levers, pvc / cp knobs if required complete all as specified. 55 attemding complaints of internal water supply pipes, fittings and bottles traps for removing of blockages etc of any description incl removing & cleaning of air locks etc. by pressure pump or any other means incl taking down and refixing of pipes & fitting and replacing old unservicable pipes and fitting with new ones in any dia of pipe complete all as specified.this item includes minor repair items as change of gi socket, elbow or t etc as reqd complete all as specified.note: new gi pipes replaced if any shall be measured and paid under respective item of this schedule. 56 attending complaints of leaking / unservicable and petty reapir to leaking bib taps , pillar taps, stop cock , angle valve , wall mixture, whb mixture, two way bib taps, etc of any description incl change of rubber washer / jumper sheet etc complete all as specified.note : all items as washers , spindles , rubber washer / jumper sheet etc are deemed to be included in quoted rate. 57 s & f as in repairs rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position cap 500 ltr incl dismantling out old pvc / rcc tank complete all as specified. 58 all as per ser item no 57.00, but cap 1000 ltrs. 59 s&f pvc tank cover for500 liter / 1000 liter water storage tank complete all as specified. 60 s&f in repairs vitreous china wash down water closet ( pedestal pattern ewc ) one piece, coloured, floor mounted coupled closet, including connection to drain ( or outgoing pipe ) , anti sypohonage pipe etc, with & including wc seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified. 61 s&f in repair vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white ( minimum ) , with grating and union for discharge pipe ( excluding flushing cistern, flush pipe and waste pipe ) complete all as specified. 62 s&f as in repairs stainless steel plate rack of size 30x24x10 size as per trade pattern fabricated with 0.50mm thick stainless steel sheet suitable for stacking 15 plates with hooks / fittings complete all as specified. 63 s&f in repairs decorative type curtain rod stainless steel finish ms pipe 22 to 25 mm diaas per sample, superior qualitycomplete andincl brackets and decorative fincals ( round type with mirror optic finish ) trade pattern for decorative type curtain rods suitable for holding & end cover complete all as specified. 64 s&f as in repairs pvc mouldedbath cabinet with mirror over all size 400x300 mm with shelves on the inner side & mirror on the shutter complete all as specified. 65 joinerytaking down chowkhat or frame with shutter ( without taking out shutter from frame ) of area not exc 1.5 sqm each complete all as specified. 66 taking down chowkhat or frame with shutter ( without taking out shutter from frame ) of area exc 1.5sqm but not exc. 4 sqm eachcomplete all as specified. 67 taking down shutter of any description area exc 1 sqm but n. exc 2 sqm each complete all as specified. 68 taking down steel windows / ventilator with frame of any description and any sizecomplete all as specified. 69 s&f solid pvc door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube supplying and fixing in opening as per specification and drawings complete all as specified. 70 s&f factory made solid panel pvc doorshutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, as per specification & drawing complete all as specified. 71 m&l framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing complete all as specified. 72 s&f 2nd class hard wood plain framed paneled shutter 35mm thick with lock rail and panel of 9mm bwp commercial ply or 12mm veneered particle board upto commercial veneering on both faces. the size of rail and stile as per is 1003 ( part i ) kiln seasoned and chemically pressure treated ( factory made shutters ) complete all as specified. 73 s&f 2nd class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc divided into squares by rails and styles , with plain chamfered or rounded mitered and rebatedsize of members of shutters as specified in ssr part i, section 8, clause 8.24 ( a ) complete all as specified. 74 s&f of steel window with side hung shutter including box type hinges with steel handle, and steel peg stay, with or without coolar opening, complete with glazing bars, dovetailed or welded complete all as specified. 75 all as per ser item no 74.00, but without glazing bars. 76 s&f steel ventilator with top hung shutters with glazed bars including hinges steel peg stay etc complete all as specified. 77 framed work such as grills, gratings, cooler stand etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 complete all as specified. 78 s & f galvanised ms wire cloth 0.56mm nominal dia of wire & 1.18 mm average width of apperturefixed complete all as specified. 79 s&f in repairs galvanised ms wire cloth 0.56mmm nominal dia of wire and average width of aperature 1.18mm complete all as specified. 80 s&f of 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative face veneer with lipping / frame to match complete all as specified. 81 m&l for pcc 1 : 3 : 6 type c1 for fixing hold fast etc for fixing of chowkhats complete all as specified. 82 m&l for bands, straps, supports or stays; hold fasts; wall ties; hooks for hanging fans;similar small articles conforming tofe 290 gde e 165 complete all as specified. 83 s&f 100mm size ss butt hinges complete all as specified. 84 s&f 300mm long mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on tapple plate and fixed complete all as specified. 85 s&f 200mm ms barraltower bolts stove enamelled black with bright bolt and fixed complete all as specified. 86 s&f in repairs 200mm ms barraltower bolts stove enamelled black with bright bolt and fixed complete all as specified. 87 s&f150mm ms pressed handle oval type stove enamelled black complete all as specified. 88 s&f in repairs, 150mm ms pressed handle oval type stove enamelled black complete all as specified. 89 s&f in repairs 150 mm size best quality floor door stopper of aluminium alloy body and tongue, anodised & hard rubber shoe complete all as specified. 90 m&l preparation of new wooden surface exceeding 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified. 91 m&l for preparation new or previously untreated surfaces of steel at any description over 10cm in width or girth and apply two coat of syntetic enamel paint complete over a coat of red oxide primer complete all as specified. 92 supply and fixing in repairs aluminium anodised extruded sectiontower bolt of size 200 mm complete all as specified. 93 supply and fixing in repairs anodised aluminium extruded section door handles size150 mm complete all as specified. 94 s& f in repairs ms sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and incl a mini of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified. 95 s & f in repairs mild steel 300mm ordinary rat tail rod pattern spring incl roller and roller plat complete all as specified. 96 supply and fixing in repairs mild steel butt hinges medium weight cold rolled100mm sizecomplete all as specified. 97 s&f in repairs stainless steel medium weight 100mm size butt hinges complete all as specified. 98 s&f in repairs mild steel body single action door spring hinge size 100 mm complete all as specified. 99 s&f in repair cast iron body door closer hydraulic regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified. 100 s & f in repairs 40mm dia cupboard knobs fixed the screw and washer of ms bright finished complete all as specified. 101 s & f in repairsmild steel body peg stays 250 mm long ( minimum ) to steel windows & vents complete all as specified. 102 s & f in repairsmild steel body window handles ( left or right ) any size to steel windows & vents complete all as specified. 103 s & f in repairsdoor seal as per trade pattern with powder coatedaluminium strip 25 30 mm width lengthhaving suitable dia holes ( for fixing screws ) & synthetic strip at bottom to avoid entry of dust etc fixed complete all as specified. 104 hacking out old broken glass any thickness, size, quality or description ) from metal frame including punching or drilling out old glazing pins / spring clips and providing complete all as specified. 105 s & f plain sheet glass panes cut to size required nexc 0.50 sqm eachthickness 3 mm thick complete all as specified. 106 s & f figured glass pin headed type nexc 0.50 sqm eachthickness 4 mm complete all as specified. 107 s & f in repairs 18 mm thickprelaminated particle board exterior grade with decorative choice laminations on one side & the other balancing white complete all as specified. 108 supply & fix continuous paino hinges 40 mm width of flap mild steel body electro galvanised finishcomplete all as specified. 109 s&f of 100 mm longhasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified. 110 checking and attending to resucuring / easing and adjusting shutters of any description and in any position area exc 1 sqm but nexc 2 sqm incl taking down of shutter from frames & refixing in the same opening after completion of repair works complete all as specified. 111 checking and attending to repairs to steel windows / vents incl necessary welding, rivetting, easingetc complete all as specified. 112 checking and attending to resucuring / easing and adjusting shutters of any description and in any position area n exc 1 sqm incl taking down of shutter from frames & refixing in the same opening after completion of repair works complete all as specified. 113 sewagechecking and attending to complaints to cleaning / removal of sewage block in the existinglinein any depth from wc to first manholes or gully trap to manholes including cleaning of wc andtesting of pipe by pouring water 100mm sgsw / rcc / ci pipe for ground floor qtr complete all as specified. 114 checking and attending to complaints to cleaning / removal of blockage in the existinglinein any depth and bathroom to first manholes or kitchen to gully trapsor gully trap to manholes includingcleaning of bathroom and whb trap and kitchen floor trapand testing of pipe by pouring water manhole 75mm sgsw / rcc / ci pipe for ground floor qtr complete all as specified. 115 cleaning of manholes completeof any size and at any location incl taking out sludge andother materialdeposited in manhole and its disposal to a distance n exc. 50 m, depth of manhole n exc 1.00 mcomplete all as specified. 116 all as per ser item no 115.00, but depth of manhole exc 1.00 m & n exc 2.00 m. 117 cleaning / removal of sewageblock in the existing line incl cleaning of complete line laid at any depth and at anylocation between two consecutive manholes / gully trap, two consecutive manhole or gully trap to manhole incl testing the pipe by pouring water from manhole for 150mm bore sgsw / rcc pipe ( np2 ) complete all as specified. 118 all as per ser item no 117.00, but 200mm bore sgsw / rcc pipe ( np2 ) . 119 cleaning of septic tanks of any capacity & any size by taking out sludge ( working condition is in foul condition ) & removing the sludge to outside defence land in closed vehiclecomplete all as specified. 120 excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in soft and disintegrated rockcomplete all as specified. 121 all as per ser item no 120.00, but exc 1.5 m depth as in soft and disintegrated rock complete all as specified. 122 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft loose soil complete all as specified. 123 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified. 124 m&l for cement concrete 1:4:8 type d2 using 40 mm graded stone agg as inin foundations, filling and mass concrete complete all as specified. 125 m&l forcement concrete 1:2:4 type b1 using 20 mm graded stone agg asin copings, kneelers, apex stones, bed plates, kerbs lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, not provided including weathering, slightly rounded or chamfered angles and throating, complete all as specified. 126 demolition ofstone / boulder masonry, built in cementmortar including all quoins, arches, pillars, etc, complete all as specified. 127 m&l for squared rubble walling jodhpur type, regular coursed, well bonded, bedded and solidly hearted, built in cm 1:6complete all as specified. 128 all as per ser item no 127.00 above, but except stone. 129 extra over to squared rubble walling, jodhpur type regular coursedmasonry for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified , brought upto coursescomplete all as specified. 130 m&l for15 mm thick rendering in cm 1:4 as in manhole / septic tank etcfinished even & smoothcomplete all as specified. 131 dismantling of cast irondrain pipes, jointed in cement mortar and taking out of trenches & walls , if required 75 / 100 mm borecomplete all as specified. 132 s & f in reapair of pvc ( swr ) pipes 110 mm single socketed in any length with rubber ring joints, laid in trenches / floor or in fixed in wall including securing with clamp & taking down pipe including all fitting etc tee, socket, bend complete all as specified. 133 s & f of pvc ( swr ) pipes 75 mm single socketed in any length with rubber ring joints , laid in trenches / floor or in fixed in wall including securing with clamp& taking down pipe including all fitting etc tee, socket, bendcomplete all as specified. 134 m&l for 75 mm cast iron soil, sand cast pipe , waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors including all fitting etc tee, socket, bend complete all as specified. 135 m&l for 100 mm cast iron soil, sand cast pipe , waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floorsincluding all fitting etc tee, socket, bendcomplete all as specified. 136 m&l for 75 mm cast iron soil, sand cast pipe , waste and vent pipes in any length with or without ears, with cement joints, fixed in wallsincluding all fitting etc tee, socket, bend complete all as specified. 137 m&l for 100 mm cast iron soil, sand cast pipe , waste and vent pipes in any length with or without ears, with cement joints, fixed in wallsincluding all fitting etc tee, socket, bendcomplete all as specified. 138 s&f in repair pvc swr bends of 110 mm borecomplete all as specified. 139 s&f in repairpvc swr bends of 75 mm borecomplete all as specified. 140 s&f in repair pvc swr tee of 75 mm borecomplete all as specified. 141 s&f in repair cast iron 100 mm vent cowlcomplete all as specified. 142 s&f in repair 75 mm borecast iron bends with oval acess door complete all as specified. 143 s&f in repair 110 mm borecast iron bends with oval acess door complete all as specified. 144 s & f in repair cat iron bends of 110 mm bore complete all as specified. 145 s & f in repair cast iron bends of 75 mm bore complete all as specified. 146 s & f in repair cast iron tee of 75 mm borecomplete all as specified. 147 s & f in repair cast iron tee of 100 mm bore complete all as specified. 148 m&lin repair 75 mm cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type b 1 ( 1:2:4 ) complete all as specified. 149 m&l for salt glazedstoneware gully traps, square or round mouthed, type p size 100 x 100 mmcomplete all as specified. 150 demolition and breaking up drain pipes ( salt glazed ware, ac or reinforced concrete ) set in cement mortar 150 / 200 mm borecomplete all as specified. 151 m&l for 150 mm bore salt glazed stoneware drain pipes laid in trenches and jointedcomplete all as specified. 152 m&l for 150 mm bore reinforced concrete pipes, class np2, laid and jointed complete with collarscomplete all as specified. 153 m&l for 200 mm bore reinforced concrete pipes, class np2, laid and jointed complete with collarscomplete all as specified. 154 material and labour for cutting into existing manholes for connecting new drains, for removing existing branch drain, making good to walling and rendering, cutting out branch channel, 150mm bore pipes complete all as specified. 155 m&l in repair for stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 / 75 mm bore pipe complete all as specified. 156 demolition of stone slabs and tiles of any description or thickness in manhole covers etc complete all as specified. 157 s&f 75mm thick jodhpur type stone slab not exc 2m in length machine cut all face & along exposed edged size faced both sided as in manhole cover complete all as specified. 158 s&fmachine made precast cement concrete blocks ( interlocking paves ) rubberised finishcoloured ( lacquer coated ) of 60mm thick with 6mm top layers of anti abrasive material , m 35 grade all as as persample kept in ge office and laid over 25mm thick sand filling layer & spreading fine sand over the tiles to fill in the joints & cleaning the same after filling of joints complete all as specified. 159 m&l for precast cement concrete laquer coated tiles 30cmx30cmx25 30mm thick machine pressed set jointd and pointed in neat cement slurry in floor complete all as specified. 160 m&l for 75mm thick cement concrete type b 1 1:4:8 ( using 20mm graded crushed stone aggregate ) as in sub base complete all as specified. 161 m&l for providing precast cement concrete type b 1 1:2:4 ( using 20mm graded agg ) as in kerb stone etc ( of any section as approved ) with plain faces , including chamfers, weathering, throating etc and setting in cement mortar 1:4 complete with joints to match complete all as specified. 162 m & l for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, includingforms, mounds, mitred / stopped end complete all as specified. 163 m&l for 25 mm thick cement concrete type b 1, 1:2:4 ( 20mm graded aggregate ) complete all as specified. 164 internal electrificationtaking down copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, sockets, lamp holder and conduit etc. removing materials to store fortaking credit and making good disturbed surfaces of walls, floors, etc complete all as specified.note: the damaged surfaces to be made good with plastering& applying colour wash in required coats tomatching with existing surfaces as directed by engineer in charge. cost of the same deem to be included in quoted rates and nothing extra on this account admissible. 165 m&l point wiring with 1.5 sq. mmpvc insulated and unsheathed single core frls copper cable 1100 volts grade with multi stranded copper conductor 02 nun phase and netural one run for earthing and including pvc casing caping ( heavy grade ) and accessories fixed on walls / floors / ceilings etc alongwith continuous earth wire 1.5 sq mm pvc insulated and unsheathed single core frls cable 1100 volts grade with stranded copper conductor and connected to common earth dolly, with and including 1.6 mm thick cadmium plated sunk ms pressed steel terminal boxes with 3 mm thick plastic laminated sheet cover fixed with brass screws complete for one light point controlled by one switch, one light / fan point controlled by one, one way switch, sp, 6 amps complete all as specified. 166 all as per ser item no 165.00, but one socket outlet, 3 pin, 5 amp, 230 volt flush type on same board. 167 all as per ser item no 165.00, but one switch socket outlet, 3 pin, 5 amp, 230 volt flush type on independentboard. 168 all as per ser item no 165.00, but one bell / buzzar point controlled by one bell push independent 169 all as per ser item no 165.00, butherein before but with 4 sqmm cable for one 3 pin 15 amp switch socket outlet and using 4 sqmm pvc single core copper conductor cable multistranded as earth wirecomplete all as specified. 170 m&l for point wiring with two single core 1.5 sq.mm size multistranded frls copper conductor pvc insulated cables and one single core 1.5 sq.mm size green colour pvc insulated, multistranded copper conductor pvc cable as earth continuity conductor, 1100 volts grade ( 02 nun phase and netural one run for earthing ) , complete drawn in and including rigid pvc conduit and conduit accessories, confirming to is specifications, concealed in wall fixing on ceiling / trusses with suitable clamps , screws etc, including 1.6 mm thick ms terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc., including connecting up and testing, one light / fan point controlled by one, one way switch, sp, 6 amps complete all as specified. 171 all as per ser item no 170.00 but one socket outlet, 3 pin, 5 amp, 230 volt flush type on same board. 172 all as per ser item no 170.00 but one switch socket outlet, 3 pin, 5 amp, 230 volt flush type on independentboard. 173 all as per ser item no 170.00 but one bell / buzzar point controlled by one bell push independent. 174 all as per ser item no 170.00 but herein before but with 4 sqmm cable for one 3 pin 15 amp switch socket outlet and using 4 sqmm pvc single core copper conductor cable multistranded as earth wire complete all as specified. 175 supply and fixswitch piano, flush type, single pole, one way, 5 amps 230 volts isi marked complete all as specified. 176 supply and fix in repair switch piano, flush type, single pole, one way, 5 amps 230 volts isi marked complete all as specified. 177 supply and fix in repairswitch piano, flush type, single pole, one way 15 amps 230 volts isi marked complete all as specified. 178 supply and fixsocket outlet 2 in 1, 3 pin, 6 amps, flush type with shutter, isi marked complete all as specified. 179 supply and fix in repairsocket outlet 2 in 1, 3 pin, 5 amps, flush type with shutter, isi marked complete all as specified. 180 supply and fix in repair ofsocket outlet 2 in 1, 3 pin, 5 and 15 amp flush type with shutters, isi marked complete all as specified. 181 supply and fixswitch socket combination2 in 1, 3 pin, 5 amps, flush type with shutter, isi markedcomplete all as specified. 182 supply and fix in repairswitch socket combination2 in 1, 3 pin, 5 amps, flush type with shutter, isi marked complete all as specified. 183 supply and fix switch socket combination 2 in 1, 3 pin, 5 and 15 amp flush type with shutters, isi marked complete all as specified. 184 supply and fix in repair switch socket combination 2 in 1, 3 pin, 5 and 15 amp flush type with shutters, isi marked complete all as specified. 185 supply and fixelectronic regulator, 100w, 250v flush type on the exiting phenolic laminated sheet etc complete all as specified. 186 supply and fix in repairelectronic regulator, 100w, 250v flush type on the exiting phenolic laminated sheet etc complete all as specified. 187 supply and fix ceiling rose, surface bakelite, three terminals complete all as specified. 188 supply and fix in repair of ceiling rose, surface bakelite, three terminals complete all as specified. 189 supply and fixlamp holder pvc / polycarbonate type with back plateisi marked for fixing bulbs complete all as directed by eic for batten fitting. 190 supply and fix in repair lamp holder pvc / polycarbonate type with back platefor fixing bulbs complete all as directed by eic for batten fitting. 191 supply and fix in repairpin top 15 ampcomplete all as specified. 192 supply and fixbuzzer, ding dong ac 230 volt, single pole complete all as specified. 193 supply and fix in repair bell multi musical type ac 230 volt, single pole complete all as specified. 194 supply and fix in repairbell push, ac 230 volt, single pole complete all as specified. 195 supply and fixspn dbs, 240 v, double door100 amps rated bus bar, 12 way complete all as specified. 196 all as per ser item no 195.00, but 8 way. 197 all as per ser item no 195.00, but 4 way. 198 supply and fix mcb spn 32 amps240 volts complete all as specified. 199 supply and fixmcb sp 6 amps to 32 amps 230 volt complete all as specified. 200 supply and fix in repair mcb sp 6 amps to 32 amps 230 volt complete all as specified. 201 supply and fix in repair modular metal flush box with white cover plate with framefor mounting, switches, sockets, fan regulator, etc. 3 module note: ( i ) switches, sockets, fan regulator, etc. will be measured and paid seperately under relevent items. 202 all as per ser item no 201.00, but 6 module 203 all as per ser item no 201.00, but 8 module cover only 204 all as per ser item no 201.00, but 12 module 205 supply and fix in repairswitch modular 5 / 6 amp single pole, one way 1 module complete all as specified. 206 supply and fix in repair switch modular 15 / 16 amp single pole, one way 1 module complete all as specified. 207 supply and fix in repairbell push modular 6 amp single pole, one way 1 module as complete all as specified. 208 supply and fix in repair fan regulatormodular 120w single pole, one way 2 module as complete all as specified. 209 supply and fix in repair socketmodular 5 / 6 amp single pole, 2 / 3 pin2 module as complete all as specified. 210 supply and fix in repair socketmodular 6 / 16 amp single pole, 2 / 3 pin2 module as complete all as specified. 211 s&f in repair metal clad plug and socketwith box20 amp with mcbsingle pole complete fixed properly on wall surface with the provisioning of suitable sizes of bolts, nuts, washer and to connect by using cable pvc insulated copper stranded conductor of size 4 sqmm as per specification complete all as specified. 212 supply and fixingin repair pvc cassing capping 20 mm size on existing sub main wiring / point wiring any sizeand prepare the existing surface in good condition complete all as specified. 213 supply and fixingin repair pvc cassing capping 25 mm size on existing sub main wiring / point wiring any sizeand prepare the existing surface in good condition complete all as specified. 214 supply and fixing in repair pvc ceiling rose back plate surface mounted round type with screw complete all as specified. 215 supply and fixing in repair metal plug and socket boths 20a 3 phase 3 pin as per is 8804 suitable for existing metal clad box complete all as specified. 216 m&l for replacementpvc rectangular block for mounting switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet cover of size 100mmx100mmx50mm deep complete all as specified. 217 m&l for replacement pvc rectangular block for mounting switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet cover of size 175mmx100mmx50mm deepcomplete all as specified. 218 m&l for replacementpvc rectangular block for mounting switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet cover of size 250mmx200mmx50mm deep complete all as specified. 219 supply and fix in repair pvc junction box with cover 25mm as per site requirement complete all as specified. 220 s&f in repair of plastic laminated sheet 3mm thick fixed withscrews complete all as specified. 221 s&f in repait fan capacitor 2.5 mfd complete all as specified....

Due Date : December 25, 2023

Tender Value : ₹ 25 Lakhs

View Tender
2
Military Engineer Services - Rajasthan

40876286 tender for periodical services including certain b / r and e / m repair work to various ascon nodes under age b / r ii at suratgarh mil stn ; 1 demolition of brick work, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by engineer in charge. 2 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the premises complete all as specified and directed by engineer in charge. 3 dismaintling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets including cover fillets complete all as directed by engineer in charge. 4 dismantling asbestos cement sheet ( corrugated, semi corrugated etc ) as in roofs etc including ridges complete all as specified and directed by engineer in charge. 5 dismantlig of timber scantling unframed work under 40 sqcm in section as in fillets, rails, posts, rafters, purlins in any position complete all as specified and directed by engineer in charge. 6 taking down steel window / ventilator of any description and of any type with or without guard bars and making good the disturbed portion complete all as specified and directed by engineer in charge. 7 taking down cement plaster or cement lime plaster on stone surface / brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by engineer in charge. 8 taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 sqm each ( without taking off the wooden shutters from the frame ) including cutting holes for hold fasts and making good disturbed surface with cement mortor or pcc after fixing new chowkats complete all as specified and directed by engineer in charge. 9 taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 sqm but not exc 4 sqm each ( without taking off the wooden shutters from the frame ) including cutting holes for hold fasts and making good disturbed surface with cement mortor or pcc after fixing new chowkats complete all as specified and directed by engineer in charge. 10 taking down and refixing door shutters of any description having area exc 1.00 sqm but not exc 2.00 sqm, each in the same opening including easing of door / window / cup board shutters for easy closing / opening incl tighening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts etc complete all as specified and directed by engineer in charge. 11 supply only integral water proofing compound ( isi marked ) complete all as specified and directed by engineer in charge. 12 m & l for plain cement concrete ( 1:3:6 ) type c 1 using 12.5mm graded stone aggregate as in filling of pressed steel frame, chowkats, hold fast blocks and other similar items etc complete all as specified and directed by engineer in charge. 13 m&l for brick work with sub class ‘b’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar ( 1:6 ) complete all as specified and directed by engineer in charge. 14 m&l for 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by engineer in charge. 15 s&f 35mm thick factory made glazed and skeleton shutters made of second class hard wood ( bonsum / hollock ) , open rebated and prepared to receive glass, gauze etc ( without sash bars ) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in ssr part i section 8 clause 8.24 ( a ) kiln seasoned and chemically pressure treated fixed to chowkat complete all as specified and directed by engineer in charge. 16 s&f factory made solid pvc door frame of size 50mm x 47mm made out of 5mm thick plain colour pvc sheet reinforced with ms square tube complete all as specified & shown in relevant drawing of item no. 08095 in mes schedule ( part ii ) and directed by engineer in charge 17 s&f 30mm thick factory made solid core pvc door shutter ( style ) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour pvc sheet, c channel having pvc sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panelling of plain colour pvc sheet to be fitted in mild steel frame welded / sealed to the styles and rails with suitable pvc sheet beading and joined together with solvent cement, complete, all as specified & shown in relevant drawing of item no. 08080 in mes schedule ( part ii ) and directed by engineer in charge. 18 s&f 200 mm long aluminium anodized barrel tower bolts of extruded section ( isi marked ) complete all as specified and directed by engineer in charge. 19 s&f as in repair 200 mm long aluminium anodized barrel tower bolts of extruded section ( isi marked ) complete all as specified and directed by engineer in charge. 20 s&f as in repair 150 mm long aluminium anodized barrel tower bolts of extruded section ( isi marked ) complete all as specified and directed by engineer in charge. 21 s&f 100mm size mild steel butt hinges cold rolled medium weight ( isi marked ) complete all as specified & directed by engineer in charge. 22 s&f as in repair 100mm size mild steel butt hinges cold rolled medium weight ( isi marked ) complete all as specified & directed by engineer in charge. 23 s&f 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type b 21 ( isi marked ) complete all as specified and directed by engineer in charge. 24 s&f as in repair 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type b 21 ( isi marked ) complete all as specified and directed by engineer in charge. 25 s&f 300mm long aluminium alloy anodised sliding door bolts with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy ( isi marked ) complete all as specified & directed by engineer in charge. 26 s&f as in repair 300mm long aluminium alloy anodised sliding door bolts with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy ( isi marked ) complete all as specified & directed by engineer in charge. 27 s&f 150mm long extruded aluminium handles, anodised, fabricated type ( isi marked ) complete all as specified and directed by engineer in charge 28 s&f as in repair 150mm long extruded aluminium handles, anodised, fabricated type ( isi marked ) complete all as specified and directed by engineer in charge 29 s&f as in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed by engineer in charge. 30 s&f as in repairs powder coated mild steel drapery rod of 20 mm inner dia ( in lengths as directed ) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with pvc rawl plug & steel screws on walls / beam, including pvc curtain rings of matching colour @ 10cm c / c all as specified & as directed. 31 s&f as in repair mild steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in cm 1:4 complete all as specified and directed by engineer in charge. 32 s&f as in repair pvc strips for wooden shutter for insects / dust proofing complete all as specified and directed by engineer in charge 33 m&l for mild steel roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc complete all as specified and directed by engineer in charge. 34 s&f factory made steel window with side hung shutters including projecting type hinges with steel handle, steel peg stay, fixing lugs etc complete with glazing bars including one shop coat of red oxide primer and cutting holes in brick wall built in cement mortar for inserting lugs and making good dismantled portion in cement mortor ( 1:3 ) or cement concrete ( 1:2:4 ) type b i complete all as specified & directed by engineer in charge 35 s&f factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of zinc chromate primer and cutting holes in brick wall built in cement mortar for inserting lugs and making good dismantled portion in cement mortor ( 1:3 ) or cement concrete ( 1:2:4 ) type b i complete all as specified and directed by engineer in charge. 36 s&f pressed steel frames for door of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed. 37 s&f pressed steel frames for door of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed. 38 m & l for pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge. 39 m & l for pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge. 40 s&f as in repair 18 / 19 mm thick prelaminated particle board exterior grade, prelaminated both sides with decorative choice lamination fixed with screws to timber frame including 6mm thick teak wood lipping fixed with head less nails / screws for shelves / partition / pelmet boxes / kitchen cabinet / cupboard shutter complete all as specified and directed by engineer in charge. 41 s&f as in repair anodised aluminium snap grid frame work of size 605mm x 605mm for false ceiling including necessary notching. the snap grid shall consist of anodized aluminium main & cross tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 kg / rm and 23.5mm x 26.4mm x1.40mm weighing 0.191kg / rm respectively. the main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5mm weighing 0.12kg / rm fixed with suitable ms bolts, nuts and washer. the snap grid ( main / cross tee section ) shall be supported at ends all along the wall with anodized aluminium angle of size 35mm x 25mm x 2mm weighing 0.36 kg / rm fixed to wall with suitable arrangement duly suspended with 3mm dia gi wire length as required @ 600mm c / c with adjustable device including plugging in brick / concrete work with steel raw plugs including making good all the disturebed portion complete all as specified and directed by engineer in charge. 42 m&l for 8mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / gi / aluminium framework with screws complete all as directed. & directed by engineer in charge. 43 m&l for non skid ceramic joint free coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar ( 1:6 ) complete all as specified and directed by engineer in charge. 44 m&l for non skid ceramic joint free coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar ( 1:4 ) complete all as specified and directed by engineer in charge. 45 m&l for glazed ceramic tiles ( coloured ) 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar ( 1:4 ) including necesary cutting as per site requirment complete all as specified and directed by engineer in charge. 46 m&l for vitrified ceramic light shade ( as approved ) coloured tiles 10mm thick ( square / rectangular ) , polished, area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar ( 1:4 ) complete all as specified and directed by engineer in charge. 47 m&l for 15mm thick rendering in cement mortar ( 1:4 ) on brick walls / concrete surfaces mixed with water proofing compound as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by engineer in charge.note : supply only water proofing compound shall be measured and paid for separately under respective item of boq. 48 m&l for 10mm thick rendering in cement mortar ( 1:6 ) on fair faced surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by engineer in charge. 49 m&l for rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified and directed by engineer in charge. 50 m&l for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by engineer in charge. 51 m&l for preparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade / tint and filling cement based putty in cracks complete all as specified and directed by engineer in charge. 52 m&l for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by engineer in charge. 53 m&l for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by engineer in charge. 54 m&l for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface etc and applying two coat of distemper oil emulsion complete all as specified & directed by engineer in charge. 55 m&l for preparation of new plastered and unplastered surfaces of wall and applying two coats of oil bound distemper including alkali resistant priming preparatory to distempering complete all as specified & directed by engineer in charge. 56 m&l for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot mulds, moss and efflorescent, salts, filling of cracks etc and applying a coat of cement based paint complete all as specified & directed by engineer in charge. 57 m&l for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by engineer in charge. 58 m&l for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by engineer in charge. 59 m&l for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by engineer in charge. 60 hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins / spring clips complete all as specified and directed by engineer in charge. 61 s&f 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing / new surfaces, complete all as specified and as directed. 62 s&f 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by engineer in charge. 63 taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by engineer in charge. 64 s&f 15mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by engineer in charge. 65 taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by engineer in charge. 66 s&f 20 mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by engineer in charge. 67 s&f as in repair gun metal globe or gate valve 20mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by engineer in charge. 68 s&f as in repair ptmt swivel shower rose of any colour with swivel joints including shower arm of 15mm bore, 195 mm long with bend of 45 degree with flanges of ptmt ( complete minimum weight 80 grams ) complete all as specified & directed by engineer in charge. 69 s&f as in replacement 600mm long pvc connection suitable for 15 mm bore with ptmt nuts on both sides complete all as specified and directed by engineer in charge. 70 s&f as in repair rotational moulded polyethylene water storage tank isi marked ( cylindrical vertical three layered with closed top ) hoisted and fixed in position of capacity 500 litres including ball brass valve, high pressure with polythene float and flynut screwed for 20 mm dia gi pipe, 25mm bore gi washout pipe 15 cm long fitted with check nut, 20mm bore over flow pipe 1.50 metre long fitted with brass anti mosquito nest coupling at the end of over flow pipe & 15mm bore gi air vent pipe 1.30 metre long fitted with tee at the end of air vent pipe ( all gi pipes shall be medium grade ) complete all as specified and directed by engineer in charge. 71 all as per srl item no. 70 here in before but 1000 ltrs capacity 72 s&f as in repair 15 mm bore bib tap, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by engineer in charge. 73 s&f as in replacement ball valves, high pressure of ptmt with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 15mm dia ( minimum weight 210 gms ) complete all as specified and as directed by engineer in charge. 74 s&f as in repair vitreous china wash basin white flat back of size 630 x 450mm including a pair of angle iron brackets, pvc connection of size 450mm, 15mm dia fancy type, cast copper alloy chromium plated pillar tap with capastan head screwed down high pressure with long screwed shank and fly nuts, 32mm dia full threaded ptmt waste coupling and 32mm dia waste pipe including cutting for and pinning in ends of brackets and 32mm dia high density polythelene ( hdpe ) pipes for pressure rating 6 kg / sqcm with all fittings such as sockets, bends, tapers, etc complete all as specified and directed by engineer in charge. 75 s&f as in repair vitreous china squatting pan orissa pattern, white of size 580x440mm with integral foot rests ( excluding flushing cistern and flush pipe ) including cast iron p or s trap, pcc filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by engineer in charge. 76 s&f as in repairs vitreous china wash down water closet pan ( pedestal pattern ) , white including connection to drain ( or outgoing pipe ) and to flushing pipe, anti sypohonage pipe etc. & with plastic wc seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by engineer in charge. 77 s&f as in repair 10 litre capacity pvc valveless symphonic action type low level flushing cistern ( isi marked ) including 32 mm dia pvc flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by engineer in charge. 78 s&f as in repair vitreous china half stall type, flat back urinal of size 390 x 375 x 590mm, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including ptmt grating and union for discharge pipe, chromium plated urinal spreader including waste pipe of polythelene of low or high density or pvc 32mm dia complete all as specified and directed by engineer in charge. 79 s&f as in repairs pvc waste pipe 32 to 40mm bore suitable for whb or sink complete all as specified and directed by engineer in charge. 80 s&f as in repair 600mm x 450mm beveled edge looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick commercial plywood including pvc moulded framing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by engineer in charge. 81 s&f as in repair 100mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed with cement joints, laid in trenches or in floor complete all as specified & directed by engineer in charge.note : cost of excavation & earthwork is deemed to included to in the unit rate of this items nothing extra shall be paid on this account. 82 s&f 100mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) with oval access door complete all as specified and as directed by engineer in charge. 83 m&l as in repair 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete ( 1:2:4 ) type b 1 using 20mm graded stone aggregate complete all as specified and directed by engineer in charge. 84 s&f in replacement 110mm bore pvc ( swr ) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite number of clamps made out of flat iron 25x4mm complete all as specified and as directed by engineer in charge. 85 s&f in replacement 75mm bore pvc ( swr ) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite number of clamps made out of flat iron 25x4mm complete all as specified and as directed by engineer in charge. 86 s&f 110 mm bore pvc ( swr ) bends any radius jointed with adhesive complete all as specified and as directed by engineer in charge. 87 s&f 75 mm bore pvc ( swr ) bends any radius jointed with adhesive complete all as specified and as directed by engineer in charge. 88 s&f in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm pvc pipe complete all as specified and directed by engineer in charge 89 s&f in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm pvc pipe complete all as specified and directed by engineer in charge 90 taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, mcb, db, lamp, earth plug etc ( excluding ms sunken boxes ) and making good the disturbed surfaces of wall / ceiling complete all as specified and as directed by engineer in charge. note : taking down of serviceable fittings shall be measured and paid separately. 91 m&l for point wiring complete with 1.5 sqmm ( nominal cross sectional area ) frlsh pvc insulated multistandard unsheathed copper conductor cable with colour coding drawn in and including new pvc rigid conduit medium grade 20mm dia and suitable fittings, fixed onconcealed or above ceiling with accessories such as pipe hooks, elbows, junction box, terminated in new sunken box and covered with new 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including cutting chases in wall for conduits and making good the disturbed surfaces of wall and including 1.5 sqmm pvc insulated unsheathed multistandard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point controlled by one way switch complete all as specified and directed by engineer in charge. 92 all as per serial item no. 91 here in before but for one 3 pin 5 amp socket outlet on the same board with other switches. 93 all as per serial item no. 91 here in before but for one 3 pin 5 amp socket outlet on independent board. 94 all as per serial item no. 91 here in before but for one bell or buzzer point controlled by by one push button on independent board. 95 all as per srl item no. 91 above, but wiring with cable of cross sectional area 2.5 sqmm ( nominal area ) multi stranded copper conductor frlsh, pvc unsheathed cable 1100 volts shade for one switch socket combination 6 pin, 5 / 15 amps on independent board including 2.5 sqmm pvc insulated multistandard unsheathed copper conductor wire as earth continuity to common earth dolly. 96 m&l for point wiring complete with 1.5 sqmm ( nominal cross sectional area ) frlsh pvc insulated multistandard unsheathed copper conductor cable with colour coding drawn in open conduit or existing concealed conduit in existing sunken box and covered with new 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including cutting chases in wall for conduits and making good the disturbed surfaces of wall and including 1.5 sqmm pvc insulated unshethed multistandard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point, bell point controlled by one switch complete all as specifiedand directed by engineer in charge. 97 all as per serial item no. 96 here in before but for one 3 pin 5 amp socket outlet on the same board with other switches. 98 all as per serial item no. 96 here in before but for one 3 pin 5 amp socket outlet on independent board. 99 all as per serial item no. 96 here in before but for one light point controlled by two way switches. 100 all as per serial item no. 96 here in before but for one bell or buzzer point controlled by by one push button on independent board. 101 all as per srl item no. 96 above, but wiring with cable of cross sectional area 2.5 sqmm ( nominal area ) multi stranded copper conductor frlsh, pvc unsheathed cable 1100 volts shade for one switch socket combination 6 pin, 5 / 15 amps on independent board including 2.5 sqmm pvc insulated multistandard unsheathed copper conductor wire as earth continuity to common earth dolly. 102 s&f switch piano flush button 5 amps single pole, one way complete all as specified and directed by engineer in charge. 103 s&f switch piano flush button 5 amps single pole, two way complete all as specified and directed by engineer in charge. 104 s&f switch piano flush button 15 amps single pole, one way complete all as specified and directed by engineer in charge. 105 s&f socket outlet 3 / 5 pin, 5 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 106 s&f socket outlet 3 / 5 pin, 15 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 107 s&f bell push, flush type, 5 amp, 230 volts grade complete all as specified and directed by engineer in charge. 108 s&f lamp holder, insulated body with back plate etc complete all as specified and as directed by engineer in charge. 109 s&f ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by engineer in charge. 110 s&f electric bell ( ding dong ) , ac, 230 volts, single pole & connecting up complete all as specified and directed by engineer in charge. 111 s&f electronic fan regulator suitable for ceiling fan 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by engineer in charge. 112 s&f sheet metal plug & socket db, sp, with a two pin and earth plug with socket, 230 volts with & including one mcb sp ‘c’ curve 10 ka, 20 amps complete all as specified and directed by engineer in charge. 113 s&f energy efficient decorative ultra slim, prewired, maxoled batten for t 8 led retro lamp, polycarbonate body, 1.2m length, ultra bright, glass shell, glare free, wide angle single / double side connection retrofit led tube with g 13 lamp holder / patti 20 watt led light fitting ( day cool light ) including 20 watt led tube with all accessories prewired fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lhfxcenntn1w020 & lhlddcxcml8q020 / crompton cat part no dijb12lt8 20 & lgt8 16 865 2 or equivalent cat part no of makes mentioned in appendix a here in after. 114 s&f energy efficient decorative ultra slim prewired 9 / 10watt ( 600mm length ) led light fitting ( mirror light ) ( day cool light ) , surface and wall mounted led batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lumilinebs9wled865s pcwh / syska cat part no ssk t5t 9w / crompton cat part no lctln 10 cdl or equivalent cat part no of makes mentioned in appendix a here in after. 115 s&f energy saving 9 / 10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge lit led luminaire comprising of high brightness leds, ip 65 protection fixed on wall complete all as specified and as directed by engineer in charge. make : havells cat part no hexaft10wled857ssy mbopc / syska cat part no ssk bh 9w / crompton cat part no lbhe 10 cdl or equivalent cat part no of makes mentioned in appendix a here in after. 116 supply and fixing led lamp minimum 3 star rated 10w led b 22 base complete all as specified and directed by engr in charge with following specifications ( a ) lumen system efficacy of lamp should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.90 ( e ) cri: morethan80 117 supply, fixing and testing led street / security light fitting of 25 watt, 5700k 6500 k ( including led drive and internally prewired ) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. the luminaries shall be monolithic construction totally enclosed dust and water proof with ip 65 / 66 protection as per is 10322 1982 ( part i ) with latest amendments and input voltage range 140 300 v, ac, frequency 50 60 hz , p.f should be more than 0.9 with total harmonic distortion thd ( i ) less than 15% , cool white colour and lamp starting time should not be more than 10 second including 10 kv surge protection in built or external. driver should be constant current constant voltage driver. driver should have high voltage withstanding capacity upto 300 v, ac. driver should also have double phase protection, no load , open circuit and short circuit protection .led light fitting should be suitable for ambient temperature from 10 degree centigrade to 50 degree centigrade and humidity level 10% to 90 % rh. covers should be polycarbonate / toughened glass to ensure minimum ip 65 degree protection. cover should not degrade due to heating and ageing. the efficiency of led luminaries system shall be more than 100 lumens per watt and must be certified by the lm 79 test report and including connection for street light from pole box with 1.5 sqmm, 3 core pvc insulated stranded copper conductor frlsh cable, 1100 volts grade isi marked including addition / alteration in bracket ( if required ) for fixing light fitting complete all as specified and directed by engineer in charge. 118 notes for srl item no 117 : ( a ) tenderer shall submit test report of led street light fitting from government accredited test laboratory for lm 79 and lm 80 . ( b ) contractor has to furnish a replacement warranty of 05 years for led light fittings complete including lamps from the date of completion of ca. contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. the product will be replaced free of cost in the following case : ( i ) manfacturing defects ( ii ) failure due to mechanical and electrical impact. ( iii ) drop in lumen ( or lux at 1 m ) below 90% of clamied values of lumen ( or lux at 1 m ) of the led / luminaries. ( c ) all led light / luminare must meet the provision laid down in is 16101 , 16102 part i / ii , 16103 part i , 16104 , 16105 , 16106 , 16108 / 2012 and 15885 part ii / section 13. ( d ) scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, if street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, in that case cost of additional / alteration is included in the unit rate of this item, which also includes needfult & p andrequired accessories such as 1.5 sqmm, 3 core pvc insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .no extra payment is admissible on this account. ( e ) light fittings shall be provided with 10 kv surge protection as mentioned in description of item. if 10 kv surge protection is not provided in light fitting for which cat part is mentioned in boq. contractor has to provide light fitting with 10 kv surge protection without any extra cost to department. ( f ) contractor shall write ca no on street light fitting with synthetic enamel paint which should be visible from ground level. cost of the same is included in the unit rate of this item nothing shall be extra paid on this account. 119 s&f as in repair flush mounting factory made spn db 4 way, 240 volt, double door, ip 43 protection, ik 09 with metal door with 100 amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by engineer in charge. 120 s&f as in repair flush mounting factory made spn db 8 way, 240 volt, single door, ip 43 protection, ik 09 with metal door with 100 amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by engineer in charge. 121 s&f as in repair flush mounting factory made tpn db 4 way, 415 volt, double door, ip 43 protection, ik 09 with metal door with 160 amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by engineer in charge. 122 s&f mcb 6 to 32 amps, single pole 240 volts, 10 ka, ‘c’ curve, complete all as specified and directed by engineer in charge. 123 s&f as in repair mcb 40 63 amps, single pole & neutral 240 volts, 10 ka, ‘c’ curve, complete all as specified and directed by engineer in charge. 124 s&f as in repair mcb 63 amps, triple pole & neutral 240 volts, 10 ka, ‘c’ curve, complete all as specified and directed by engineer in charge. 125 s&f as in replacement switch piano flush button 5 amps single pole, one way complete all as specified and directed by engineer in charge. 126 s&f as in replacement switch piano flush button 5 amps single pole, two way complete all as specified and directed by engineer in charge. 127 s&f as in replacement switch piano flush button 15 amps single pole, one way complete all as specified and directed by engineer in charge. 128 s&f as in replacement bell push, flush type, 5 amp, 230 volts grade complete all as specified and directed by engineer in charge. 129 s&f as in replacement socket outlet 3 / 5 pin, 5 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 130 s&f as in replacement socket outlet 6 pin, 15 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 131 s&f as in replacement lamp holder, insulated body with back plate etc complete all as specified and as directed by engineer in charge. 132 s&f as in replacement ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by engineer in charge. 133 s&f as in replacement switch socket combination 3 pin, 15 amps, 240 volts, flush type complete all as specified and directed by engineer in charge. 134 s&f as in replacement electric bell ( ding dong ) , ac, 230 volts, single pole & connecting up complete all as specified and directed by engineer in charge. 135 s&f as in replacement electronic fan regulator suitable for ceiling fan 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by engineer in charge. 136 s&f as in repair 3mm thick phenolic laminated sheet cover of size 8 x 5 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 137 s&f as in repair 3mm thick phenolic laminated sheet cover of size 9 x 5 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 138 s&f as in repair 3mm thick phenolic laminated sheet cover of size 9 x 11 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 139 s&f as in repair 3mm thick phenolic laminated sheet cover of size 11 x 5 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 140 s&f as in replacement energy efficient decorative ultra slim, prewired, maxoled batten for t 8 led retro lamp, polycarbonate body, 1.2m length, ultra bright, glass shell, glare free, wide angle single / double side connection retrofit led tube with g 13 lamp holder / patti 20 watt led light fitting ( day cool light ) including 20 watt led tube with all accessories prewired fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lhfxcenntn1w020 & lhlddcxcml8q020 / crompton cat part no dijb12lt8 20 & lgt8 16 865 2 or equivalent cat part no of makes mentioned in appendix a here in after. 141 s&f as in replacement energy efficient decorative ultra slim prewired 9 / 10watt ( 600mm length ) led light fitting ( mirror light ) ( day cool light ) , surface and wall mounted led batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lumilinebs9wled865 spcwh / syska cat part no ssk t5t 9w / crompton cat part no lctln 10 cdl or equivalent in makes mentioned in appendix a here in after. 142 s&f as in replacement energy saving 9 / 10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge lit led luminaire comprising of high brightness leds, ip 65 protection fixed on wall complete all as specified and as directed by engineer in charge. make : havells cat part no hexaft10wled857ssy mbopc / syska cat part no ssk bh 9w / crompton cat part no lbhe 10 cdl or equivalent in makes mentioned in appendix a here in after. 143 supply and fixing in replacement led lamp minimum 3 star rated 12w led b 22 base complete all as specified and directed by engr in charge with following specifications ( a ) lumen system efficacy of lamp should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.90 ( e ) cri: morethan80 144 s&f in replacement led post top 40 watt decorative circular design energy saving, ip 65 protection environmental freindly, long life aesthetically designed with symmetrical light distribution, cast aluminium body landscape luminaire with high power leds with polycarbonate type diffuser including two coat of black painting on existing post and cement work in base stand ( spigot housing with decorative opal acrylic diffusser and ip 65 protection with all accessories complete all as specified and as directed by engineer in charge. 145 s&f in replacement sub main wiring complete with 2 single core 6 sqmm ( nominal area ) multi stranded copper conductor pvc insulatedunsheathed cable frlsh drawn in and including heavy duty pvc conduit isi marked not less than 25mm dia concealed including single core multistranded copper conductor 6 sqmm size cable as earth continuity wire drawn in same conduit complete all as specified and directed by engineer in charge note :two runs of 6 sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittingsshall be measured as one length. 146 supply, fixing and testing as in replacement led bldg / security light fitting of 25 watt, 5700k 6500 k ( including led drive and internally prewired ) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. the luminaries shall be monolithic construction totally enclosed dust and water proof with ip 65 / 66 protection as per is 10322 1982 ( part i ) with latest amendments and input voltage range 140 300 v, ac, frequency 50 60 hz , p.f should be more than 0.9 with total harmonic distortion thd ( i ) less than 15%, cool white colour and lamp starting time should not be more than 10 second including 10 kv surge protection in built or external. driver should be constant current constant voltage driver. driver should have high voltage withstanding capacity upto 300 v, ac. driver should also have double phase protection, no load , open circuit and short circuit protection .led light fitting should be suitable for ambient temperature from 10 degree centigrade to 50 degree centigrade and humidity level 10% to 90 % rh. covers should be polycarbonate / toughened glass to ensure minimum ip 65 degree protection. cover should not degrade due to heating and ageing. the efficiency of led luminaries system shall be more than 100 lumens per watt and must be certified by the lm 79 test report and including connection for street light from pole box with 1.5 sqmm, 3 core pvc insulated stranded copper conductor frlsh cable, 1100 volts grade isi marked including addition / alteration in bracket ( if required ) for fixing light fitting complete all as specified and directed by engineer in charge. 147 notes for srl item no 145 : ( a ) tenderer shall submit test report of led street light fitting from government accredited test laboratory for lm 79 and lm 80 . ( b ) contractor has to furnish a replacement warranty of 05 years for led light fittings complete including lamps from the date of completion of ca. contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. the product will be replaced free of cost in the following case : ( i ) manfacturing defects ( ii ) failure due to mechanical and electrical impact. ( iii ) drop in lumen ( or lux at 1 m ) below 90% of clamied values of lumen ( or lux at 1 m ) of the led / luminaries. ( c ) all led light / luminare must meet the provision laid down in is 16101 , 16102 part i / ii , 16103 part i , 16104 , 16105 , 16106 , 16108 / 2012 and 15885 part ii / section 13. ( d ) scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, if street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, in that case cost of additional / alteration is included in the unit rate of this item, which also includes needfult & p andrequired accessories such as 1.5 sqmm, 3 core pvc insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .no extra payment is admissible on this account. ( e ) light fittings shall be provided with 10 kv surge protection as mentioned in description of item. if 10 kv surge protection is not provided in light fitting for which cat part is mentioned in boq. contractor has to provide light fitting with 10 kv surge protection without any extra cost to department. ( f ) contractor shall write ca no on street light fitting with synthetic enamel paint which should be visible from ground level. cost of the same is included in the unit rate of this item nothing shall be extra paid on this account. 148 s&f as in repair capacitor of 3.15 mfd capacity, 230 volts including provision of insulation sleeves isi marked complete all as specified and directed by engineer in charge. 149 s&f as in replacement plug top 3 pin, 5 amp, 230 volt ac complete all as specified and as directed by engineer in charge. 150 s&f as in replacement plug top 3 pin, 15 amp, 230 volt ac complete all as specified and as directed by engineer in charge. 151 m&l for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of gi wire 4 mm dia ( 8 swg ) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia gi light grade top of pipe with funnel & wiremesh, and bottom connected to earth plate by slit and two bolts / nuts / washers, pcc chamber in cement concrete ( 1:2:4 ) type b 1 and 40mm thick rcc cover, excavation & earth work complete all as shown in electrical plate no. 3 of mes schedule part i of ssr 2009 including taking down old eathing complete all as specified and directed by engr in charge.notes : ( i ) cost of gi wire upto 7.5m is included in this item. ( ii ) pcc 1:2:4, excavation, earthwork is included in the quoted rate of this item. ( iii ) cost of gi tubing upto 7.5m is included in the quoted rate of this item. ( iv ) outer edge of earth pit chamber shall be 1.5 metre away from the outer edge of pcc chamber. ( v ) minimum weight of reinforcement for rcc cover shall be 1 kg. 152 supplying and fixing as in repair 1100 volts grade heavy duty cable pvc insulated solid aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections in and including wherere required pvc conduit 20mm diaof 6 sqmm, one twin core cable flat or circular complete all as specified and directed by engineer in charge.notes : ( i ) excavation, earth work, sand cushioning, cable protection inlcuded in this item. nothing shall be extra paid on this account. ( ii ) road cutting / floor cutting / cutting holes etc in walls required for laying / fixing of cable etc shall be made good as per existing. nothing extra shall be admissible on this account. quoted rates shall deemed to be inclusive of the above provisions. 153 s&f as in repair switch socket combination 3 pin, 5 amps, 240 volts, flush type complete all as specified and directed by engineer in charge. note : a sum of rs. 68575 / will be deducted on account of credit for dismantled / demolished / taken down material. please refer details on srl page no. 28 to 30 ( schedule of credit ) of tender documents....

Due Date : December 12, 2023

Tender Value : ₹ 18 Lakhs

View Tender
3
Military Engineer Services - Rajasthan

40874623 tender for special repair of qtr 57 and 60 ( offers md accommodation ) of certain unit at mil station kota. ; 1 demolition / dismantling of existing roof treatment, any type from rcc roof slab including lime concrete / pcc padding over roof, removing layer of bitumen under lime concrete / pcc padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside md land, complete all as specified and directed. 2 demolition / dismantling of existing roof treatment, any type from rcc sunken slab including lime concrete / pcc filling materials around wc upto top of existing sunken slab, removing layer of bitumen under lime concrete / pcc sunken, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside md land, complete all as specified and directed. 3 taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 4 taking down chowkhat or frames not exc 1.50 sqm each with shutters ( with out taking off shutters from the frame ) , complete all as specified and directed. 5 taking down chowkhat or frames exc 1.50 sqm and not exc 4.00 sqm each with shutters ( with out taking off shutters from the frame ) , complete all as specified and directed. 6 takingdown shutters of any description exc 1 sqm and not exc 2 sqm each and removing from site complete all as specified and directed. 7 takingdown shutters of any description exc 2 sqm each and removing from site complete all as specified and directed. 8 takingdown and re fixing after rescuring or easing and adjusting of any description exc 1 sqm & n. exc 2 sqm each in the same opening complete all as specified and directed. 9 takingdown and re fixing after rescuring or easing and adjusting of any description exc 2 sqm each in the same opening complete all as specified and directed. 10 demolition of cement concrete ( un reinforced ) of any description and in any position not otherwise specifically provided for and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 11 demolition of cement concrete ( un reinforced ) in ground floor and pavings n.exc 15 cm thickness ( below or above gl ) and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 12 demolition of cement concrete ( reinforced ) as in roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work for and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 13 dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. 14 demolition of stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed. 15 dismantling floor, hearth or wall tiling / terrazzo including cement mortar bedding ( but not backing ) , removing tiles and rubbish off the premises, complete all as specified and directed. 16 demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed. 17 providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed. 18 treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and directed. 19 m&l brick work with old size pulverized fuel ash lime bricks ( fly ash bricks non modular size ) , straight or curved on plan exc 6 m mean radius, built in cm 1:6, complete all as specified and directed. 20 m&l for brick work with pulverised fuel ash lime bricks ( fly ash bricks non modular size ) , straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed. 21 m&l for pcc 1:3:6 type c 2 ( using 40mm graded stone aggreate ) , 75 mm thick as in plinth protection / path / pcc paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling ( one part of hot bitumen 85 / 25 and three parts of fine sand by weight ) , complete all as specified & directed. 22 m&l for 100mm thick plain cement concrete 1:3:6 type c 2 ( using 40 mm graded crushed stone aggregate ) as in flooring / sub base finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 23 m&l for 50mm thick plain cement concrete 1:2:4 type b 2 ( using 40 mm graded crushed stone aggregate ) as in flooring finished surface even & smooth without using extra cement complete all as specified and directed. 24 m&l providing cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating & formwork, complete all as specified and directed. 25 m&l providing cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed. 26 s & f 40mm gi pipe, medium grade, 60cm long out of which 20cm projected outside for spout pipe, placed in slope to drain water accumulated in sunken portion including making good in cm 1:3 for the damaged portion complete all as specified and directed. 27 m&l for pcc 1:2:4 mix type b 0 ( using 12.5 mm graded crushed stone agg ) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed. 28 m&l brushing neat cement slurry with 3.00 kg cement per sqm, complete all as specified and directed. 29 m&l for applying 15 mm thick screed in cm 1:4 on roof slabs with using liquid water proofing compound as per manufacturers instructions, complete all as specified and directed. ( liquid wpc shall be measured and paid separately ) . 30 m&l for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and supply and fix app polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 kg / sqm, black finish reinforced with non woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to is 3384 @ of 0.40 kg / sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. note: ( i ) coved fillets in pcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall / mumty / chimney / other vertical surfaces and thereafter surface painted with hot paving bitumen of grade 30 / 40 confirming to is 73, applied@1.20 kg / sqm over a coat of cold applied bituminous primer conforming to is:3384 @ 0.40 kg / sqm. 31 item 30.00 contd........ ( ii ) polymeric membrane shall be taken to a height of 45cm ( minimum ) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. ( iii ) the waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. ( iv ) in case of stone masonry parapet wall etc a groove of size 25mmx25mm ( minimum ) shall be made in coved fillet at the junction of roof and parapet wall / mumty chimney / other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. ( v ) cost of above aspects is deemed to be included in quoted rates. 32 m&l for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and supply and fix app polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 kg / sqm, black finish reinforced with non woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to is: 3384 @ 0.40 kg / sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed.note: ( i ) the waterproofing treatment shall be got carried out through the manufacturer or their authorized applicators only. 33 supply only approved liquid water proofing compound, complete all as specified and directed. 34 s&f 35mm thick factory made iind class hard wood ( hollock ) paneled door shutters two panel with lock rail and panel of 9mm b.w.p. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to is 710 or 12mm thick particle board veneered with commercial veneering on both faces. the size of rails & style as specified in ssr part i ( 2009 ) section 8 and as per is 1003 ( part i ) kiln seasoned as per is 1141 and chemically pressure treated as per is 401 complete all as specified and directed. 35 s&f 35mm thick factory made iind class hard wood ( hollock ) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass / gauge etc. the size of rails & style as specified in ssr part i ( 2009 ) section 8 and as per is 1003 ( part i ) kiln seasoned as per is 1141 and chemically pressure treated as per is 401 complete all as specified and directed.note : s & f glass / gauge shall be measured and paid for separately. 36 m&l in renewal of 18 / 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. 37 s&f in renewal of factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick pbi sheet and shutter made of 1.00 mm thick pbi sheet with 6 nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. ( total width including frame shall be measured for payment purpose ) . 38 s&f in renewal of 18 mm thick hdwpc ( high density wooden plastic composite ) kitchen cupboard / door shutter board, one side colour / white laminate and other side decorative as in modular kitchen / cabinet door shutters fixed with minifix hardware where ever required & including edge band 22 mm wide 0.80m thick of matching colour on exposed surfaces of board fixed with polymaster adhesive including trimming edges of edge band to true line of thickness of board by manual trimmer, fixed to wall etc, complete all as specified and directed. 39 s&f in renewal of 18 mm thick hdwpc ( high density wooden plastic composite ) board of both side white laminate as in back kitchen and other side un decorative as in back of kitchen cabinet / partition of cupboard etc, complete all as specified and directed. 40 s & f in renewal continuous ( piano ) hinges, stainless steel, matt or brush finish, width of flaps ( when open ) in 40mm complete all as specified and directed. 41 s&fof ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified and dirceted. 42 s&f ss handles, fancy type, 100 mm size, complete all as specified and directed. 43 s & f auto closing hinges, three dimentional adjustment with suitable mounting plate made of stainless steel with nickel plated for corrosion resistance for cupboard and cabinet shutters of kitchen, complete all as specified and directed. 44 s & f in renewal of kitchen basket cutlery stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 45 s & f in renewal of kitchen basket plate rack stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 46 s & f in renewal of kitchen basket utensils stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 47 s&f of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed. 48 s&f aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed. 49 s&f aluminium handles, cast type, anodised 100 mm size, complete all as specified and directed. 50 s&f aluminium handles, cast type, anodised 150 mm size, complete all as specified and directed. 51 s&f 100 mm sizemild steel butt hinges, isi marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed. 52 s & f 250 mm long aluminium alloy, anodised sliding door bolts ( isi marked ) with bolt not less than 16mm dia with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as specified and directed. 53 s&f 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, welded to mild steel frame complete all as specified and directed. 54 s&f snake guard ( door seal aluminium plate with rubber beading ) for door etccomplete all as specified and directed. 55 supply only stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, fixed to door, window, ventilator etc complete all as specified and directed. ( note: cost of fixing of wire cloth shall be deemed included in the unit rates under respective items. ) 56 s & f for solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in ssr part – ii ( 2020 ) . 57 s & f for factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in ssr part–ii. 58 providing and fixing factory made upvc white colour sliding window ( area not exceeding 2.00 sqm each ) , three track made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm ) . window profile with hollow section with multi chamber. frame ( 88mm x 52mm ) , sliding sash ( 42mm x 67mm ) . sliding mesh sash ( 42mm x 57mm ) sliding interlock ( one vertical length in each shutters ) ( 45.5mm x 28mm ) , glazing bead ( 24.5mm x 16mm ) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. epdm gasket, 1.2+ 0.2mm thick galvanised steel frame ( 30mm x 18mm ) 2 nos, sliding sash ( 30mm x18mm ) , sliding mesh sash ( 26mm x 10mm ) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, hardware.touch lock of zinc alloyed ( white powder coated ) , steel roller system. stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories etc., complete all as specified and directed.note : ( i ) the unit rate quoted by contractor includes cost of glass and ss steel wire cloth and includes all other connected accessories. net opening will be measured for payment purpose. ( ii ) provision for fixing the ac and cooler shall be included in rate quoated by the bidder, no payment shall be made on this account and no misunderstanding entertained in later stage. ( iii ) bidder shall note that all the accessories ( packing, hinges, handles etc ) of upvc window shall be maintained by manufactureres till defect libility period and quoated rate shall be included this provision. 59 supply and fixing factory made upvc white colour fixed glazed window / ventilator made of ( small series ) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension ( area upto 0.75 sqm. ) comprising of upvc multi chambered frame and mullion ( where ever required ) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length ( shape & size according to upvc profile ) , upvc extruded glazing beads of appropriate dimension, epdm gasket, g.i. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame shall be mitred cut and fusion welded at all corners, mullion ( if required ) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality including provision of exhaust fan etc., complete all specified and directed. note : ( i ) for upvc frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. ( ii ) the unit rate quoted by contractor includes cost of glass and ss steel wire cloth and includes all other connected accessories. net opening will be measured for payment purpose. ( iii ) provision for fixing the exhaust fan shall be included in rate quoated by the bidder, no payment shall be made on this account and no misunderstanding entertained in later stage. ( iv ) bidder shall note that all the accessories ( packing, hinges, handles etc ) of upvc window / ventilator shall be maintained by manufactureres till defect libility period and quoated rate shall be included this provision. 60 s&f factory made steel windows conforming to is 1038 with side hung shutters & including box type hinges, with 2 nos steel handles, 2 nos tower bolts & steel pag stay complete ( without glazing bars ) , dovetailed or welded including fixing of lugs in pcc 1:2:4, type b 1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide / zinc chrome primer complete all as specified and directed.note : ( i ) ss or ms cloth wire shall be measured and paid for sepparately under respective items. ( ii ) window size and pattern wherever required and directed shall be suitable for installing desert cooler. 61 s&f factory made steel ventilator with top hung shutter including hinges, steel peg stay and including one coat of red oxide / zinc chrome primer complete all as specified and directed. 62 s&f factory made steel ventilator with fixed type shutter without glazing bars including hinges, steel peg stay and including one coat of red oxide / zinc chrome primer complete all as specified and directed. 63 welding in repairs thickness of metal to be welded not exc 6mm and length of welding exc 2.5 cm but not exc 5cm complete all as specified and directed. 64 s&f sheet glass 3 mm thick ordinary quality and glazing with oil putty etc in squares n.exe 0.50 sqm in each pane, complete all as specified and directed. 65 s & f of framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings ( excluding of steel sheeting or other covering running rails and guides ) and hanging also fastening and fixing, conforming to fe 290 grade e 165, complete all as specified and directed. 66 s&f mild steel framed work as in grills, grating etc. with end of bars shouldered and / or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: cages, frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to fe 290 grade e 165, complete all as specified and directed. 67 m & l for cutting holes in brick / stone masonary walls in cement mortar exc. half brick but not exc. one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type b 1 as required, complete all as specified and directed. 68 dismantling plain or corrugated steel sheeting, any gauge, any thickness incl hooks and ridge as retrieved from site complete all as specified and directed. 69 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering, wall cladding etc, fixed to iron / wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed. 70 re fixing only pre painted galvalume aluminium zinc coating ( gi based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering, wall cladding etc, fixed to iron / wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.note : pre painted galvalume aluminium zinc coating sheets obtained from dismantling shall be reused under this item. 71 s&f in renewal of stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed. 72 m&l 100 mm thick pcc 1:4:8 type d 2, using 40 mm graded crushed stone aggregate, as in sub base of floors, etc., finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 73 m&l machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to is 15658 2006 of 60 mm thickness, m 35 grade, laid over and including 25 mm thick sand cushioning, complete all as specified and directed. 74 m&l for 25mm thick plain cement concrete 1:2:4 type b 1 ( using 20 mm graded crushed stone aggregate ) as in flooring / sub base finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 75 m&l for joint free non skid ceramic coloured tiles, 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cm 1:6, complete all as specified and directed. 76 m&l for light coloured vitrified tiles, 10mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm ( 600x600mm ) , in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cm 1:6, complete all as specified and directed. 77 m&l for light coloured vitrified tiles, 10mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm ( 600x600mm ) , fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in cm 1:4 backing, complete all as specified and directed. 78 m&l glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in cm 1:4 backing, complete all as specified and directed. 79 m&l for machine cut kota stone slab as in flooring 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing andmirror polishing by applying wax polish, laid over and including 15 mm thick screed bed in cm 1:4, complete all as specifiedand directed. 80 m&l for machine cut kota stone slab as in skirting, dado, risers etc, 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and mirror polishing by applying wax polish, laid over and including 15 mm thick rendering in cm 1:4, complete all as specifiedand directed. 81 m&l for grinding of the existing marble / kota stone flooring by mechanical process using corborundum stone of appropriate grit, cleaning & finally mirror polishing by applying wax polish complete all as specified and directed. 82 m&l black granite ( of any type ) slab 18 20 mm thick, table rubbed and mirror polished by applying wax polish as in cooking platform, jambs, cills, pillars, tread, risers, platform for whb etc including bull nosing to exposed outer edges, set in cm 1:4 bedding and pointing with white cement mixed with pigment and provn of hole for gas pipe, laid over and including 20 mm thick screed bed in cm 1:6, complete all as specified and directed.note : granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of slab. 83 m&l for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed. 84 m&l for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed. 85 m&l for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4 ( using water proofing compound as per manufacturers instructions ) , surface finished even and smooth without using extra cement, complete all as specified and directed. ( liquid wpc shall be measured and paid separately ) . 86 m&l for rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed. 87 m&l for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide zinc chrome primer, complete all as specified and directed. 88 m&l for preparing old steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. 89 m&l applying 2 coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed. 90 m&l applying two coats of synthetic enamel paint on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the old surfaces complete all as specified and directed. 91 m&l preparation of newly plastered surfaces of walls and applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats distempering with 1st quality acrylic distemper ( ready mixed ) having voc content less than 50 gms / litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification over new surfaces on walls complete all as specified and directed. 92 m&l for complete removal of existing treatment from previously treated plastered / unplastered surfaces of walls and applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats distempering with 1st quality acrylic distemper ( ready mixed ) having voc content less than 50 gms / litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification over new surfaces on walls complete all as specified and directed. 93 m&l preparation of newly plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces over new surfaces on walls complete all as specified and directed. 94 m&l for complete removal of existing treatment from previously treated plastered / unplastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces over new surfaces on walls complete all as specified and directed. 95 m&l for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed. 96 m&l for applying two coats of white wash after preparation of old previously treated plastered surfaces of walls, complete all as specified and directed. 97 m&l for applying one coat of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed. 98 s&f in renewal of hdpe pvc connection 450 mm long suitable for 15 mm gi pipe with two ptmt nuts and rubber washers complete all as specified and directed. 99 s&f in renewal of vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl pvc waste pipe of 32 mm bore, suitable size of waste fittings, one pair of 600 mm long cast iron brackets, complete all as specified and directed. 100 s&f in renewal of shower rose, chromium plated brass, 100 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed. 101 cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 102 taking up or down existing gi tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed. 103 taking up or down existing gi tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed. 104 supply, fixing, laying & testing 15 mm bore galvanised iron water tubing medium grade with and including all gi fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed. 105 supply, fixing, laying & testing 20 mm bore galvanised iron water tubing medium grade with and including all gi fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed. 106 dismantling existing water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed. 107 dismantling existing water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed. 108 s&f in position rotational moulded polyethylene water storage tanks 500 lts capacity, white colour ( cylinderical verticalwith closed top ) hoisted and fixed in position, complete all as specified in ssr part i and as directed.note: pvc tank shall be isi marked and having three layers. 109 s&f in position rotational moulded polyethylene water storage tanks 1000 lts capacity, white colour ( cylinderical verticalwith closed top ) hoisted and fixed in position, complete all as specified in ssr part i and as directed.note: pvc tank shall be isi marked and having three layers. 110 s&f of 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed. 111 s&f in renewal of 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. 112 s&f in renewal of 15 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. 113 s&f in renewal of stop valve 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup ( concealed type ) , screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to gi socket complete all as specified and directed. 114 s&f in renewal of bib taps, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handles, screwed down, screwed for 15 mm bore gi pipe or for brass ferrule orto gi socket complete all as specified and directed. 115 s&f in renewal of angle valve 15 mm bore cast copper alloy, cp, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed. 116 s&f in renewal of two way angle valve 15 mm bore, cast copper alloy, chromium plated with long shank and cup ( concealed type ) , screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to gi socket complete all as specified and directed. 117 s&f in renewal of kitchen sink mixer cp hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging etc completeall as specified and directed. 118 s&f in renewal of wall mixer fitting with built in non return valve with 3 in 1 wall mixer, chromium plated brass, fancy type for 15mm bore completeall as specified and directed. 119 s&f in renewal of basin mixture cp hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging etc completeall as specified and directed. 120 s&f in renewal of vitreous china floor mounted water closet pan ( pedestal pattern ) with & including superior quality dual type low level pvc flushing cistern, water jet spray and health faucet & including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc., & including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed. 121 s&f in renewal of vitreous china squatting pan orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed. 122 s&f in renewal of 10 ltr capacity pvc low level flushing cistern, top push type with inlet ball valve, pvc float, brackets & including superior quality pvc flush pipe of 32 mm dia, completeall as specified and directed. 123 s&f in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality pvc waste pipe and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm fixed on granite stone slab and top of granite stone match with top of kitchen sink complete all as specified and directed. note : granite stone slab shall be measured and paid in separately with appropriate item of boq. 124 s&f in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality pvc waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. 125 s&f in renewal of stainless steel utensil plate rack of size 900 x 600 x 200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the ge, complete all as specified and directed. 126 s&f in renewal of 600x450 mm bevelled edge mirror 5.5 6mm thick selected quality glass flaw less, mounted in 6 mm thick ac buildings board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 127 s&f in renewal of ptmt alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed. 128 s&f in renewal of soap dish fancy type, chromium plated, approx size 160x160x90mm, fixed to plugs with chromium plated brass screws etc, complete all as specified and directed. 129 s&f in renewal of toilet paper holder, chromium plated, fixed to plugs with chromium plated brass screws etc, complete all as specified and directed. 130 s&f in renewal of 300 mm corner glass shelf with abs brackets etc, complete all as specified and directed. 131 s&f in renewal of grating doom of 100 mm dia, made of mild steel chromium plated, complete all as specified and directed. 132 s&f in renewal of pvc ( swr ) 75 mm dia floor trap, with cp grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type b1 ( using 20 mm graded stone aggregate ) complete all as specified and directed. 133 s&f in renewal of salt glazed stoneware gully traps of size 150x150, square or round mouthed, type p complete all as specified and directed. 134 s&f in renewal of 100mm cast iron sanitary connection socket to fit wc out let complete all as specified and directed. 135 s&f pvc ( swr ) pipe 75 mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floor and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 136 s&f pvc ( swr ) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 137 s&f pvc ( swr ) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 138 s&f pvc ( swr ) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed. 139 s&f pvc ( swr ) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed. 140 s&f pvc ( swr ) 110 mm bore junction single, ( single t ) equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 141 s&f pvc ( swr ) 75 mm bore junction single, ( single t ) equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 142 s&f pvc ( swr ) vent cowl 110 mm dia, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 143 s&f stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 100 / 110 mm, complete all as specified and directed. 144 s&f stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 75 / 80 mm, complete all as specified and directed. 145 demolition and breaking up drain pipes 150mm dia ( salt glazed ware, ac or reinforced concrete ) set in cement mortar complete all as specified and directed. 146 m&l for cement concrete 1:4:8 type d 2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe complete all as specified and directed. 147 m&l 150 mm bore reinforced concrete pipes, class np2, laid to slope in trenches and jointed in cm 1:1 and tested, complete all as specified and directed. 148 excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 sqm on plan and getting out in soft / loose soil, complete all as specified and directed. 149 returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed. 150 removing excavated materials ( soil ) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed. 151 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. 152 dismantling unserviceable main switch / dbs incl wooden board and deposit to mes store yard including making good disturbed surface of wall complete all as specified and directed. 153 taking down sub main wiring of any size / capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed. 154 m&l for point wiring with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 1.5 sqmm with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 1.5 sqmm as earth continuity wire to be drawn in and including pvc concealed conduit not less than 20 mm dia including with all accessories and fittings, fixed in concealed & including providing ms sheet metal sunken switch / terminal box 1.2mm thick for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete allas specified and directed for the following: one light / ceiling fan / exhaust fan / bell buzzer point controlled by one, one way switch of 5 / 6 amps.note : cutting chases and making good to match with the adjoining surface deemed to be included in the unit quoted rate. 155 all as per item no 153.00 ( here in before ) but one 5 pin, 5 / 6 amps socket outlet point on independent board, controlled by one, one way 5 / 6 amp switch. 156 all as per item no 153.00 ( here in before ) but one 5 pin, 5 / 6 amps socket outlet point on same board, controlled by one, one way 5 / 6 amp switch. 157 all as per item no 153.00 ( here in before ) but one light point controlled by two, two way switch of 5 / 6 amps. 158 m&l point wiring with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 2.5 sqmm, with pvc insulated ( frls ) unsheathed multi stranded copper conductor cablefrls of size 2.5 sqmm as earth continuity wire to be drawn in and including pvc concealed conduit not less than 20 mm dia including with all accessories and fittings, fixed in concealed for one socket outlet 15 amp on independent board & including providing ms sheet metal sunken switch / terminal box 1.2mm thick and fittings for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.note : cutting chases and making good to match with the adjoining surface deemed to be included in the unit quoted rate. 159 s&f modular switch 1 way 5 / 6 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 160 s&f modular switch 1 way 15 / 16 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 161 s&f modular socket, 5 / 6 amps, 2 / 3 pin combined 2 module, 240 volts, isi marked, complete all as specified & directed. 162 s&f modular socket, 6a / 16a amps, 2 / 3 pin combined 2 module, 240 volts, isi marked, complete all as specified & directed. 163 s&f modular bell push, 5 / 6 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 164 s&f in renewal of modular fan step regulator, 120w 2 module, complete all as specified & directed. 165 s&f in renewal of buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed. 166 s&f in renewal of modular metal flush box 8 module, isi marked, complete all as specified & directed. 167 s&f in renewal of modular metal flush box 6 module, isi marked, complete all as specified & directed. 168 s&f in renewal of modular metal flush box 3 module, isi marked, complete all as specified & directed. 169 s&f in renewal of modular metal flush box 1 / 2 module, isi marked, complete all as specified & directed. 170 s&f modular white cover plate with frame, 8 module, isi marked, complete all as specified & directed. 171 s&f modular white cover plate with frame, 6 module, isi marked, complete all as specified & directed. 172 s&f modular white cover plate with frame, 3 module, isi marked, complete all as specified & directed. 173 s&f modular white cover plate with frame, 2 module, isi marked, complete all as specified & directed. 174 s&f modular white cover plate with frame, 1 module, isi marked, complete all as specified & directed. 175 s&f switch piano flush type 5 / 6amps, 230 volts, single pole, one way, isi marked, complete all as specified & directed. 176 s&f switch piano flush type 5 / 6amps, 230 volts, single pole, two way, isi marked, complete all as specified & directed. 177 supply and fixingswitch socket combination, 5 / 6 and 15 / 16amps, 230 volt, multi pin, flush type universal, complete all as specified and directed. 178 supply and fixing socket outlet, 5 / 6 amps, 230 volt, five pin, flush type universal, complete all as specified and directed. 179 s&f pvc / polycarbonate lamp holder, angular / batten type with back plate, isi marked complete all as specified & directed. 180 s&f in renewal of stepped type electronic fan regulator, flush type, 230 volts ac, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed. 181 s&f ceiling rose surface type pvc / polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed. 182 s&f in renewal of wall mounted 20 watt led tube light fittings, 4 feet in length, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed. 183 s&f in renewal of wall mounted 10 watt led tube light fittings, 2 feet in length, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed. 184 s&f in renewal of led street light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection, complete all as specified and directed. 185 m & l in renewal of street / road light gi mounting bracket made out of steel tube, medium grade, 32 mm dia ( or higher size to suit the opening of the fitting ) 0.550 mtr long by hydraulic pressed mechine bend to require arc shape and fixed to pole with 02 nos ms flat iron clamps of suitable size fixed with bolts, nuts and washers including drilling holes and grouting with the same for fixing bolts as required & incl duly painted with two coat of aluminum paint over a coat of aluminum red oxide primer and fixing with lights fittings on the existing old street light poles complete all as specified and directed. note : cost of necessary tools and plants such as ladders, hydra for renewal of mounting brackets, light fittings, nuts, bolts etc shall be deemed to be included in the unit rate quoted. 186 s&f mcb, 6 to 32 amps, single pole, 240 volt, 10 ka c curve including all accessories, complete all as specified and directed. 187 s&f mcb, 40 to 63 amps, single pole & neutral, 240 volt, 10 ka c curve including all accessories, complete all as specified and directed. 188 s & f in renewal of single pole and neutral enclosure with a two pin and earth plug and socket complete with & including one single pole mcb of 20 amps complete, all as specified & directed. 189 s & f mccb 125 amps, 415 volts, four pole, c curve, adjustable type with rupturing capacity 36ka conforming to is 8828 1996, iec 60898 and testing for proper functioning complete, all as specified & directed. 190 s & f factory made verticle tpn db, 4 way, double door, ip 43, as per is 8623 iii, impact resistance ik 09 with the provision of 125 amp mccb 4 pole, 25 ka as incomer, 160 amp rated busbar, blanking plates with all electrical connection complete all as specified and directed.note for items of mcb db ( 1 ) the unit rate includes for cutting the brick / stone walls to accommodate db to make flush to wall. ( 2 ) the unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface. 191 s & f factory made mcb db made of sheet steel phosphatised, powder painted with bus bar 200 a, neutral link, earth bar and din rail, 240 volts spn with 8 ways, double door, complete all as specified and directed. 192 s & f factory made mcb db made of sheet steel phosphatised, powder painted with bus bar 200 a, neutral link, earth bar and din rail, 240 volts spn with 12 ways, double door, complete all as specified and directed. 193 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 10 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 10 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. note for items of submain wiring: ( i ) cutting chases of stone masonary wall and making good to match with the adjoining surface deemed to be included in the unit quoted rate. ( ii ) two runs of cable one run of earth wire and one run of pvc non metallic conduit of 20mm dia shall be measured as one run length. ( iii ) cable required for connection to dbs shall deemed to be included and shall not be measured separately. ( iv ) earth wire shall run inside the pvc conduit. 194 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 6 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. 195 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 4 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. 196 m&l for earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground ( earth plate not less than 2.25 mtr below normal ground level ) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade gi tubing for protection of earth wire, ms sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 cm compacted thickness all around the electrode with concrete earth pit of pcc 1:3:6 type 75 mm thick precast rcc ( 1:2:4 ) type b1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft / loose soil and disposal of spolis to a distance not exc 50 mtr and necessary connection and testing complete all as shown in electrical plate no. 3 and including dismantling and taking out old earthing complete all as specified and directed.notes: ( a ) irrespective of whatever is shown in plate no 5 of ssr, earth pit shall be casted in pcc ( 1:3:6 ) type c 1 and precast cover of rcc ( 1:2:4 ) type b 1 with suitable handle. ( b ) item includes the cost of gi pipe for protection of earth wire and earth wire upto 7.5 m. any variation below or above shall be measured and paid for separately under relevant item of this sch ‘a’. 197 s&f in renewal of exhaust fan, steel body ac single phase. 230v of size 230mm, sweep with, blades, and frame and louvers & including connecting with and including pvc insulatedthree core 23 / .0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing mes no with black syntheticenamel paint 2.0 cm high and including making appropriate hole in the wall / window complete all as specified and directed. 198 s&f in renewal of exhaust fan, steel body ac single phase. 230v of size 300mm, sweep with, blades, and frame and louvers & including connecting with and including pvc insulatedthree core 23 / .0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing mes no with black syntheticenamel paint 2.0 cm high and including making appropriate hole in the wall / window complete all as specified and directed. 199 m & l for taking down carefully of serviceable geyser from its existing position by disconnecting all connection and keeping it in safe custody and refixing / re installation the same with nuts, bolts, fastnersand electrical connection etc., complete all as specified and directed. 200 s&f in renewal of hdpe pvc connection 600 mm long suitable for 15 mm gi pipe with two ptmt nuts and rubber washers complete all as specified and directed. 201 m & l for taking down carefully ceiling fans, exhaust fans, wall fanscomplete with blade and deposited it into mes stores & re fixing of the same to the specified locations and including connecting of ceiling rose with and including pvc insulatedthree core 23 / .0076 copper conductor cable, complete all as specified and directed....

Due Date : December 20, 2023

Tender Value : ₹ 37.80 Lakhs

View Tender
4
Military Engineer Services - Rajasthan

40784310 tender for special repair to bldg no p 152 ( jcos mess ) at mil station sri ganganagar.; 1 dismatiling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by engineer in charge. 2 demolition of mud in roofs, any thickness, including plastering and leeping ( whether full thickness removed or only a part thereof ) complete all as specified and directed by engineer in charge. 3 s&f heat resistance tiles ofsize 300x300x10mm thick on roof slab of any colour approved over and laid including 15mm thick in cm 1:4.techinical specification of roof tiles shall be as prer is 4457:2007 complete all as specified and directed by engineer in charge. 4 m&l for roof treatment to rcc roofas follows : ( a ) cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections, cleaning joints, washing, drying and removing all dirt / dust to receive concrete padding / plaster etc complete. ( b ) providing 15 mm thick screed bed or bedding layer in cement mortar ( 1:4 ) with wpc , finished even and smooth without using extra cement. ( c ) providing one coat of approved bituminous primer @ 100 gms per sqm, over dried plastered surface. ( d ) laying 3 mm thick app based polymeric membrane, ( mineral finish ) minimum weighing 3 kg / sqm reinforced withnon woven polyster fabric ( weight not less than 150 gms / sqm ) by torch application. the overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by engineer in charge.makes: stp, dr fixit, sikka, torch tar notes: ( i ) all joints and change in directions should be covered with cement mortar ( 1:3 ) mixed with sbr latex @ 200 ml / bag of cement / as per site requirement and cured well before laying membrane by torching. ( ii ) all angles and abuttments should be sealed well with extra care to ensure full bondage. ( iii ) water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only.the name of firm shall be got approved from ge before carrying out the work. ( iv ) the independent testing of membrane for technical parameters given in particular specificationsshall be carried out from govt approved labs having fascilities for testing of membrane. ( v ) the guarantee of treatment shall be for minimum 10 yearsreckoned from date of completion of whole work complete all as specified and directed by engineer in charge. 5 m&l pcc 1:2:4, type b1 using 20 mm graded stone aggregate as in roof kerbs / benching / coved fillets etc rounded or chamfered on edges, complete all as specified and directed by engineer in charge. 6 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , and rubbish off the premises complete all as specified and directed by engineer in charge.. 7 m&l 300x600 x7 mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles and incliding 10mm thick backing coat in cm 1:4. complete all as specified and directed by engineer in charge. 8 m&l non skid ceramic coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles and incliding 15mm thick screed in cm 1:6 complete all as specified and directed by engineer in charge. 9 m&l light shade vitrified ceramic tiles 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over screed bed or bedding layer of mortar 15 mm thick in cm 1:6 for laying floor finishes complete all as specified and directed by engineer in charge. 10 m & lmachine cut kota stone slab flooring 18 20mm thick ( minimum size 55 cms x 55 cms ) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing including 15mm thick of screed bed in cm 1:6.complete all as specified and directed by engineer in charge. 11 m & l machine cut kota stone slabs as in vertical surfces such as risers of steps 18 20mm thickover cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing also moulding edgesincluding 10mm thick of backing coat in cm 1:4, complete all as specified and directed by engineer in charge. 12 m&l granite ( of any type ) work18 to 20 mm thick ( table rubbedand polished ) in steps, jambs, pillars, window cills, cooking platforms, hand wash platform and like laid over and including 12 mm thick cement mortar in cm 1:4including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by engineer in charge. 13 demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for ( reinforcement cut as required to facilitate demolition ) complete all as specified and directed by engineer in charge. 14 m&l providingreinfoced cement concrete ( nominal mix ) in cement concrete 1:2:4 type b1 ( 20mm graded aggregate ) as chajjas, lintel, plinth beametcand similar workcomplete all as specified and directed by engineer in charge. ( note : the rate quoted shall be deemed to include use and waste of necessary form work ) 15 m&l tmt bar 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9 mm dia complete all as specified and directed by engineer in charge. 16 m&l for providing precast rcc jallies ( cement concrete type b0 1:2:4 12.5mm gragded aggregate ) louvres and jallies, 40 mm thick ( measured solid ) , including allmouldings & set in cm 1:4 complete all as specified and directed by engineer in charge. 17 demolition concrete in ground floors and pavings n exc 15cm thickness ( below or above ground level ) complete all as specified and directed by engineer in charge. 18 m&l75 mm thick cement concrete type d2, 1:4:8 ( using 40mm graded stone aggregate ) filling sub base as in floors, paving, sub floor etc finished even and smoothcomplete all as specified and directed by engineer in charge. 19 m&l 25mm thick cement concrete flooring type b0, 1:2:4 using 12.5 mm graded aggregate finished even and fair complete all as specified and directed by engineer in charge. 20 m&l for sand filling ( 25mm thick ) under floors or in foundations including watering and consolidation complete all as specified and directed by engineer in charge. 21 m&l machine pressed precastrubber moulded concretecoloured interlocking paver block any shape and size confirming to is 15468 2006 of 60 mm thickness with grey cement and pigmentm 35 grade 20mm graded stone aggregate ) complete all as specified and directed by engineer in charge. 22 m&l providing precast cement concrete in pcc ( 1:2:4 ) type b 1 with 20 mm graded aggregate for kerb stone and similar works with plain fair finishes including chamfers, weatherings, throat ing etc. and setting in mortar ( 1:4 ) complete with joints to match complete all as specified and directed by engineer in charge. 23 m & l for 75mm thick cement concrete type c 1, 1:3:6 using 20mm graged aggregate as in plinth protection complete all as specified and directed by engineer in charge. 24 m & l for 40mm thick cement concrete type b 1, 1:2:4 using 20mm graged aggregate as in flooring , finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by engineer in charge. 25 dismantling of brick work built in cement mortar of any description complete all as specified and directed by engineer in charge. 26 m&l for brick work with sub class b bricks ( old size ) straight or curved on plan exc 6 m mean radius built in cm 1:6complete all as specified and directed by engineer in charge. 27 m&l for brick work with sub class b bricks straight or curved on plan exc 6 m mean radius built in cm 1:6 but except bricks complete all as specified and directed by engineer in charge. 28 taking down cement plaster any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by engineer in charge. 29 m&l rendering 15 mm thick in cm ( 1:6 ) finished even and smooth without using extra cement as on brick work surfaces complete all as specified and directed by engineer in charge. 30 m&l 15mm thick rendering in cm 1:4 to brick / concrete wall surfaces finishedeven & smooth w / o using extra cement. complete all as specified and directed by engineer in charge. note: work is to be carried out upto 10 mtr height. 31 m&l 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by engineer in charge. 32 m&l for preparation ofnewly plastered surface of wall any description and applying twocoats of oil emulsion distemper over & including 3 mm thick wall putty over a coat of chalk whiting layer on plastered surfaces preparatory to distempering complete all as specified and directed by engineer in charge. 33 m & l preparation of new plastered surfaces of wall and applying two coats of cement base paint over & including 3 mm thick wall putty over one coat of alkali resistantprimer complete all as specified and directed by engineer in charge. 34 m & l for three coats of white washing on new plastered surfaces of on ceiling surface including preparation of surface complete all as specified and directed by engineer in charge. 35 m&l for preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and removing all dirt and dust by watering making surface even and smooth and then applying two coats of cement base paint over over & including 3 mm thick wall putty well prepared old decorated plastered surface etc complete all as specified and directed by engineer in charge. 36 m & l for preparation of old decorated wall surfacesby brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spotsand then applying two coats of oil bounddistemper over & including 3 mm thick wall puttycomplete all as specified and directed by engineer in charge. 37 m & l forold decorated ceiling surfacesby brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spotsandthen applyingtwo coats of white washcomplete all as specified and directed by engineer in charge. 38 taking downsteel window / ventilators complete all as specified and directed by engineer in charge. 39 taking down chowkats or frames ( without taking off shutters from the frame ) not exceeding 1.5 sqm each complete all as specified and directed by engineer in charge. 40 taking down shutters of any description exc 1 sqm but n exc 2 sqm each complete all as specified and directed by engineer in charge. 41 taking down chowkats or frames with shutters ( without taking off shutters from the frame ) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and directed by engineer in charge. 42 taking down shutters of any material and description exc 1 sqm but n exc 2 sqm each and refixing in same opening after resecuring easing duly completed repair work in all respects etc.complete all as specified and directed by engineer in charge. 43 taking down shutters of any material and description n exc 1 sqmeach and refixing in same opening after resecuring easing duly completed repair work in all respects etc.complete all as specified and directed by engineer in charge. 44 s&f steel windows with side hung shutters includinghinges with steel handle and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified and directed by engineer in charge. 45 s&f 10mm dia m. s round guard bars for steel windows & including welding complete all as specified and directed by engineer in charge. 46 s&f ms falt iron 25 x 6mm as in hold fast confirming to fe 290 gde e 165 complete all as specified and directed by engineer in charge. 47 m&l for cutting holes in brick ( n.exc half brick ) walls in cement mortar forinserting holdfasts andmaking gooddismantled portion incement mortar 1:3 or cement concrete 1:2:4type b 1 complete all as specified and directed by engineer in charge. 48 s&f framed brackets of angles or tee with web and flange cut to shape, drilled and counter shunk for screw, including bending and welding angles asnecessary gusset plates riveting rails, braces, running rails and guides and hanging; also fastening and fixing complete conforming to fe 290 ( grade 165 ) complete all as specified and directed by engineer in charge. 49 s & f factory made pressed steel frames of frame size 125 x 60mmfor doors with one or more rebatesincluding necessary fixing lugs, hold fasts, hinges, lock strike plate, etc., complete all as specified and directed by engineer in charge. ( note : mild steel sheet shall be 1.25mm thick ) 50 s & f factory made pressed steel frames of frame size 105 x 60mmfor doors with one or more rebatesincluding necessary fixing lugs, hold fasts, hinges, lock strike plate, etc., complete all as specified and directed by engineer in charge. ( note : mild steel sheet shall be 1.25mm thick ) 51 m&l for providing cement concrete ( 1:3:6 ) type c1 using 20 mm gradded stone aggregate for filling in pressed steel frames and other similar items complete all as specified and directed by engineer in charge. 52 s & f 2nd class hard wood plain solid straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed by engineer in charge. 53 s & f 35mm thick factory made shutter, plain, framed, panelled shutters factory made ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by engineer in charge. 54 s & f factory made second class hard wood glazed and skeleton door, window shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number& fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in ssr part i, section 8 clause 8.24 ( a ) complete all as specified and directed by engineer in charge. 55 s&f 18 / 19mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work, including piano hinges, sliding channels and wheels with magneting cather / locking arrangements and beading etccomplete all as specified and directed by engineer in charge. 56 s & f continuous ( piano ) hinges, ( width of flap 40mm when open ) mild steel, bright finish or electrogalvanised complete all as specified and directed by engineer in charge. 57 s&f in repair aluminium 150 mm long hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed by engineer in charge. 58 s&ffiber glass reinforced plastic ( frp ) door frames of three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness. the laminate door frame molded with fire retardant grade unsaturated polyster resin and chopped mat. door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiberglass from all sides. m s stay shall be provided at the bottom to steady the frame complete all as specified and directed by engineer in charge. 59 s&f factory made 30mm thick fiber glass reinforced plastic ( frp paneled doorshitter ofrequired colour and approved brand and manufacture made with fire retardant grade unsaturated polyster resin. moulded to 3mm thick frp laminate for forming places for fixing of fittings cast monolithically with 5mm thick frp laminate for panels and conforming to is 14856 2000 complete all as specified and directed by engineer in charge. 60 s&f 100 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type c 21 complete all as specified and directed by engineer in charge. 61 s&f 125 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type c 21 complete all as specified and directed by engineer in charge. 62 s&f 75 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type c 21 complete all as specified and directed by engineer in charge. 63 s&f 125 aluminium anodised barrel tower bolts of extruded sction and fixedcomplete all as specified and directed by engineer in charge. 64 s&f aluminium handle cast type anodised, 150mm long complete all as specified and directed by engineer in charge. 65 s&f 300mm long aluminium alloy anodised sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by engineer in charge. 66 s&f aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed by engineer in charge. 67 s&f 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engineer in charge. 68 s&f in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engineer in charge. 69 s&f stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by engineer in charge. 70 s&f in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by engineer in charge. 71 s & f for floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised, with hard drawn steel spring, complete all as specified and directed by engineer in charge. 72 hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads complete all as specified and directed by engineer in charge. 73 s&f 4mm thick sheet glass ordinary quality and glazing with oil putty in squaren. exc 0.5 sqm in each plane complete all as specified and directed by engineer in charge. 74 s&f 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares n.exc 0.5 sqm in each pane complete all as specified and directed by engineer in charge. 75 s&faluminium frame for doors, window, ventilatorswith one or more rebates including joining cleat for fixing including sliding chennals etc complete with powder coating on aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners . aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of engineer in charge 76 s&f powder coated aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, powder coated aluminum snap beading screws etc. including sliding channel, wheel, cleats with whole arrangement complete all as specified and directed by engineer in charge 77 s&faluminiumwindowsand ventilator shutters, side hung typewithout sash bars, aluminium saction weighing 0.55 kg / m including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as aluminiumpeg stay 150mm long ( 1no ) , powder coated aluminiumhinges type b 21 100 mm long ( 2no ) , suitable powder coatedaluminium handle ( 1no ) , and powder coated aluminium self closing tower bolt 75mm long ( 1no ) complete all as specified and directed by engineer in charge. 78 s&f powder coated aluminium grills to aluminium windows including all necessary fixing arrangments of size 50 mm x 5 mm thick complete all as specified and as directed by engineer in charge.note: design shall be approvedby engineer in charge. note : minimum thickness of powder coating shall not be less than 50 micron. 79 s & f for 5.5mm thick sheet glass ( tinted ) , selected quality and glazing with necessory arrangement in square exc 0.5 sq. m in each pane complete all as specified and directed by engineer in charge. 80 m&l for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying onecoat of synthetic enamel paint complete all as specified and directed by engineer in charge.. 81 m&l for preparation of new wooden and wood base surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and directed by engineer in charge. 82 m&l for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed by engineer in charge. 83 m&l for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed by engineer in charge. 84 s&f in repairs white vitreous china squatting pan orissa pattern of size 580mm x 440 mm, with integral foot rest and p or s trap connection to trap and to flushing pipe front or back inlet including, trap complete all as specified and directed by engineer in charge. 85 s&f in repair vitreous china wash down water closet pan ( pedestal pattern ) , white complete, including white seat cover with hinging arrangement, ( excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed by engineer in charge. 86 s&f in repairs 10 ltr capacity low level pvc valveless, syphonic action type flushing cistern ( dual system ) , white, with inlet, ball valve, flush pipe, pvc connection 15 mm dia and 450 mm long float and handle including bracket. complete all as specified and directed by engineer in charge. 87 s&f in repair cp toilet paper holdercomplete all as specified and directed by engineer in charge. 88 s&f in repair cp soap dish complete all as specified and directed by engineer in charge. 89 s & f in repairs 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by engineer in charge. 90 s & f in repair 15 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by engineer in charge. 91 s&f in repairs chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by engineer in charge. 92 s&f in repairs chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by engineer in charge. 93 s&f in repair concealed chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by engineer in charge. 94 s&f in repairs chromium plated 15mm bib taps cast copper alloy, chromium platedfency type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by engineer in charge. 95 s&f in repairs pvc connection 15mm size with ptmt nuts of length 450mm long complete all as specified and directed by engineer in charge. 96 s&f in repairs pvc connection 15mm size with ptmt nuts of length 600 m long complete all as specified and directed by engineer in charge. 97 s&f cp gratings 100 mm diafixed in repairs. ( minimumweight25 gms ) complete all as specified and directed by engineer in charge. 98 taking up or down gi steel water tubing 15mm bore and connections including fittings from floor / walls / ceiling complete all as specified and directed by engineer in charge. 99 taking up or down gi steel water tubing 20mm bore and connections including fittings from floor / walls / centrings complete all as specified and directed by engineer in charge. 100 s & f galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall / ceiling or laying in floors and making good complete all as specified and directed by engineer in charge. 101 fixing only tubes, of 15mm bore any grade, ( medium ) to walls and ceilings or laying in floors complete all as specified and directed by engineer in charge. 102 s & f gi steel water tubing 20mm bore medium grade with all fittings and fixed complete to walls ceiling or laid in floors complete all as specified and directed by engineer in charge. 103 fixing only tubes, of 20 mm bore any grade, ( medium ) to walls and ceilings or laying in floors complete all as specified and directed by engineer in charge. 104 dismantling water tanks any type exc. 250 ltr but nexc 500 ltr complete all as specified and directed by engineer in charge. 105 s & f rotational moulded polythylene water storage tank ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i ( 1000 ltrs ) capacity. complete all as specified and directed by engineer in charge. ( note : pvc tanks shall be isi marked & having two layers ) 106 supply and fixing ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed for bore dia of pipe 20mm.complete all as specified and directed by engineer in charge. 107 dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required.complete all as specified and directed by engineer in charge. 108 s&f 100mm bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by engineer in charge 109 s&f 75mm bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by engineer in charge 110 s&fcast iron 100mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed by engineer in charge. 111 s&fcast iron 75mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed by engineer in charge. 112 s&f cast iron 100 mm bore branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and directed by engineer in charge. 113 s&f cast iron 75 mm bore branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and directed by engineer in charge. 114 s&fcast iron100 mmbore branch pieces, double ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and directed by engineer in charge. 115 s&f cast iron 75 mm bore branch pieces, double ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branchescomplete all as specified and directed by engineer in charge. 116 s& f 100 mm bore cast iron sockets ( double ) collars complete all as specified and directed by engineer in charge. 117 s& f 75 mm bore cast iron sockets ( double ) collars complete all as specified and directed by engineer in charge. 118 s&f 100 mm cast iron traps ‘p’ or ‘s’complete all as specified and directed by engineer in charge. 119 s&f100 mm cast iron cowls complete all as specified and directed by engineer in charge. 120 taking down eaves gutters and rainwater pipes, pvc ( swr ) pipes ( any size or pattern ) including all fittings heads , shoes, bends, and removal to store complete all as specified and directed by engineer in charge. 121 s&f 110 mm borediapvc ( swr ) pipes single socketed in any length with rubber ring joints, fixed to walls includingnecessary scaffolding upto the height of buildingfrom ground level complete all as specified and directed by engineer in charge. 122 s&f 110 mm dia pvc ( swr ) bend with oval access door complete all as specified and directed by engineer in charge. 123 supply and fixing drapery curtain rod 25mm dia, fancy type, fabricated out of stainless steel steel sheet not less than 20 guage, including brackets and pair of decorated end knobs ( finials ) , stop roller etc, pretreated powder coated natural color completeall as specified & directed by engineer in charge. 124 s&f in rep aluminium door closer hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by engineer in charge. 125 s&f in replacement double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by engineer in charge. 126 s & f in repair stainless steel sink with drainage board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mmcomplete all as specified and directed by engineer in charge. 127 dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by engineer in charge. 128 m & l for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing complete conforming to fe 290 ( grade 165 ) complete all as specified and directed by engineer in charge. 129 m & l framed work as in doors or gates of angle or other section with gusset plates, for stainless steel framed work as in multipurpose vegitable rack, ration rack, utensils racks, plate rack ofgde 304 ordoors or gates of angle or other section with gusset plates, rails, braces, including ss wire guage arragements in sides etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing complete complete conforming complete all as specified and directed by engineer in charge. 130 excavating post holes ( or similar holes ) each n.exc. 0.5 cum getting out returning filling, in and ramming with earth around in layers not exc. 25 cm includingwatering and removing surplus soil to a distance n.exc. 50m and making good surface in soft loose soil complete all as specified and directedbyendineer in charge. 131 m&l pcc 1:3:6 ( 40mm graded stone aggregate ) type c2, in foundation of posts and strutscomplete all as specified and directedbyendineer in charge. 132 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directedbyendineer in charge. 133 s&f pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directedbyendineer in charge. 134 s&f 0.56 mm thickplain, aluminium sheeting, alloy 31000 h4 for crumple / expansion joints, ridges, hips, valley gutter, drip, and straight flashing ( length and girth as fixed ) fixed with self tapping screws complete all as specified and directedbyendineer in charge. 135 s & f for steel work in tubular trusses , channels , purlines, crange gantries, rails including special shaped washer, platesnuts and bolts, gusset plates, including necessary drillingetc. complete using erw or induction butt welded tubes conforming to i. s.1161 1979 grade st. 240 complete all as specified and directedbyendineer in charge. 136 s & f for flat ironfor wind ties, plates ( plain or chequered ) channels, posts, square cut or notched ( ordinary and counter sunk ) forming holesetcfe 410 w ( gde e 250 ) quality a complete all as specified and directedbyendineer in charge. 137 s&f mild steel screw bolts ( machine made ) with hexagonal or square head at one end, and screwed the other, or screwed bothend to be fitted with washer and one hexagonal / square nut not exceeding 5cm long and dia of neck 11 to 15mm complete all as specified and directed by engineer in charge. 138 s&f for dwcpe ( s n 8 ) drain pipe 150mm internal dia confirming to is 16098 part ii 2013 laid in trenches on moorum bed to required slope including all accessories / fitting complete all as specified and directed by engineer in charge.note: moorum shall be paid separately. 139 excavation in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and directed by engineer in charge. 140 returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm.in soft / loose soil complete all as specified and directed by engineer in charge. 141 removing excavated material n exc. 50 mtr and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by engineer in charge. 142 m & l for pcc ( 1:4:8 ) type d2 ( 40mm graded stone aggregate ) as in foundation lean concrete complete all as specified and directed by engineer in charge. 143 m&l for pcc 1:3:6 type c 2 ( 40mm graded stone agg. ) concrete in surface channels and drains complete all as specified and directed by engineer in charge. 144 m&l for brickwork withsub class `b bricks, straight or curved on plan exc 6m meanradius, built in cm 1:4 in half brick thick wall / on edge wall complete all as specified and directed by engineer in charge. 145 taking down carefully copper / aluminium point wiring ( light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in cm 1:3 etc complete all as specified and directed by engineer in charge. 146 dismantling and taking down fluorescent / ledtube light / wall light / ceiling light single / bulk head / tube light / suspension light / mirror light double of any wattage or size street light fittings for repair / refixing purpose all as specified and directed by engr in charge. 147 fixing only led lights fitting 1x 20 / 25w, 220v, led tube light / security light / bulk head / mirror light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 148 m & lfor concealed conduit point wiring complete for light / fan on independent / combine boardwith cable 1.5 sqmm ( nominal area ) frlshpvc insulated multistranded unsheathed copper conductor, drawn in and includingpvc concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , aftercutting in wall chasing for conduits and sinkings for sunkencast iron / pressed steelterminal boxes suitable lengthandthickness for mounting, switches, sockets, fan regulatorwith 3 mm thick plastic laminated sheet cover fixedwith brass screwed and cup washers, dulygrouting and painted with red oxide metal primer and making the gooddisturbed surfaces of wallin cm 1:3 with white wash or existing colour including provision ofcontinuousearth continuity conductoralong with point wiring of 1.5 sqmm copper pvc insulated cable for one light / fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddirecedby the engineer in charge. 149 all as per srl item no 148 here in before but for one switch socket combination5 / 6 amp on independent board complete all as specified and directed by engineer in charge. 150 all as per srl item no 148 here in before but for one three pin socket outlet 5 amp on same board with other switches complete all as specified and directed by engineer in charge. 151 all as per srl item no. 148 here in before but for one switch socket combinationt 6 pin 5 / 15 amps on independent board with copper conductor 2.5 sqmm complete all as specified and directed by engineer in charge. 152 s & f switch piano flush type 5 / 6 amps single pole one way complete all as specified and directed by engineer in charge. 153 s & f switch socket combination 5 pin, type 5 / 6 amps flush type complete all as specified and directed by engineer in charge. 154 s & f switch socket combination 6 pin, 5 / 16 amps flush type complete all as specified and directed by engineer in charge. 155 s & f socket outlet 5 pin 5 amps flush type complete all as specified and directed by engineer in charge. 156 s & f ceiling rose surface bakelitethree terminals complete all as specified and directed by engineer in charge. 157 s & f in repair compact & decorative energy efficient led mirror light fitting with antiglare diffuser and decorative end caps suitable for 1x10 watt fitting 2 ft version including led lamp 10 watt complete all as specified and directed by engineer in charge. 158 s & f in replacement of existing light fitting withled batten with aliminium housing andintegrated electronic driver, 20 watt having input voltage ac90 300v, 50 hz , 6500k, and all other accessories including connection with flexiblecable copper conductortwin coreof size 23 / .2 mm upto ceiling rose / connector complete all as specified and directed by engineer in charge. 159 s & f angle holder insulated body with back plate for conduit fittings complete all as specified and directed by engineer in charge. 160 s&f led lamp 9w for angle holder complete all as specified and directed by engineer in charge. 161 s & fin replacement water tight bulk head fitting, comprision of connector , weather proof enamelled gallery , glass well, and including 10 watt led lamp all as specified and directed by engineer in charge. 162 s&f in replacementmcb protected socket 25amps in renewal with plastic box and plug topvertical din rail mount type suitable to operate at 240v current rating range 25a , 50hz 1ph, complied is specification 13032 & 8623 complete all as specified and directed by engineer in charge. 163 s&fin replacementround recess mounted led edge lit slim downlight 12 watt ( 6500k ) with opal diffuser and separate electronic driver die cat aluminum housing fineshed in premium white powder coating efficacy 100lm / w complete all as specified and directed by engineer in charge. 164 s&f decorative, wall mounting, made of polycorbonate suitable for 9 w led lamp, b22 base complete all as specified and directed by engineer in charge. 165 s & f stepped type, single socket fan regulator for ceiling fan 1200 / 1400mm sweep complete all as specified and directed by engineer in charge. 166 s & f in replacement of sub main wiring with two single core cables pvc insulated and un sheathed 6 sqmm ( nominal area ) frlsh multistranded copper conductor drawn in concealedpvc conduict dia 25mm “medium quality” conduit including 6.00 sq mm ( nominal area ) copper cableas earthcontinuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and coversincluding necessary connections, pvcflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by engineer in charge. ( note : pvc cable and pvc conduit shall be isi marked ) 167 s & f in replacement of sub main wiring with two single core cables pvc insulated and un sheathed 4 sqmm ( nominal area ) frlsh stranded copper conductor drawn in concealedpvc conduict dia 25mm “medium quality” conduit including 4.00 sq mm ( nominal area ) copper cableas earthcontinuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and coversincluding necessary connections, pvcflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by engineer in charge. ( note : pvc cable and pvc conduit shall be isi marked ) 168 s & f in repairs sheet metal enclosure for double door db made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted sp & n 8 ways, 240 volts, isi marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation mcbs and isolators etc complete all as specified and directed by engineer in charge. 169 s & f in repairs sheet metal enclosure for double door db made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted sp & n 12 ways, 240 volts, isi marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation mcbs and isolators etc complete all as specified and directed by engineer in charge. 170 s&f in repairs mccb tp&n 63 amps with breaking capcity 16ka , fixed tm and 415 volts ac supply isi marked complete all as specified and directed by engineer in charge. 171 s & f in repairs mcb ‘c’ series type suitable for 240 volts, ac supply5 to 40 amps, s p & n with over load and short circuit protection and rupturing capacity not less than 10ka complete all as specified and directed by engineer in charge. 172 s & f in repairsmcb ‘b’ series type suitable for 240 volts, ac supply5 to 40 amps , single pole with over load and short circuit protection and rupturing capacity not less than 10ka complete all as specified and directed by engineer in charge. 173 m & l for earthing complete with gi earth plate electrode 60 cm x 60 cm x 6 mmthick burried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of plate not less than 1.5 mtr below ground level , connecting to gi earth lead 4 mm dia gi earth wire , by means of bolts, nuts and washers of giand protection by provisionof gi medium grade pipe 15 mm bore including provision of concrete pit in pcc ( 1:2:4 ) type b1 using 20 mm grade stone aggregate with 40 mm thick cover of rcc ( 1:2:4 ) reinforced with xpm ( weight not less than 4kgs / sqmm ) and frame of angle iron 25mmx25mmx6mm with lugs 02 nos and with 6 mm dia ms bar handle made to shape , gi light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmx 8 mm fi with fixing arrangement , funnel, wire mesh and earth work inhard dense soil , returning filling in and removal of surplus soil to a distance not exceeding50 mtrs all as per electric plate no.3 of ssr part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by engr in charge 174 s&fin replacement security light fitting led type 25 watt with all necessary acessories, clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 hz ac & supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23 / 0.0076 complete all as specified and directed by engineer in charge 175 s&f in repairs sheet metal enclouser for doble door vertical dbs made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting vtpn 4 way 415 voltisi marked 250amps busbar stove enameled dust and vermin proof, ip:43 protection suitable for incorporation fp mccb ( v tech ) n1 frame upto 125a, isolators and including give connection with wire and cable etc complete all as specified and directedby engineer in charge . 176 supply and fix pvc body tent / industrial type desert cooler ( 1135x600x1535mm ) alongiwth four wheels, electric driven ( single phase ) , 3 speed motor with 950 rpm, 30 inch axial type fan , noise level 68 db, having nominal air flow capacity of 18000cmh / 10500 cfm, large size, pad size ( 1100x100x1150mm ) , water tank 90l capacity, black color complete all as specified and directed by engineer in charge 177 hanging only ceiling fan ( m.d. supply ) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by engineer in charge 178 fixing only exhaust fan ( m.d. supply ) and connecting upincluding provision of cable from ceiling rose / connector to fan and clean the existing exhuast fan with chemical solution complete all as specified and directed by engineer in charge 179 s&f rj 45 data and tv socket eachfor connection of data network and tv cable ( dish ) complete all as specified and directed by engineer in charge 180 s&f rigid non metaliic pvc conduit 20mm dia inclusive of all tees, bends , elbows , reducers , bell mouth tube ends and complete with all fixing accessories such as couplers , lock nuts, saddles, pipehooks etc complete all as specified and directed by engineer in charge 181 s&fsteelbody exhaust fan of 300mm sweep , 240 volt , 900 rpm, 5 star rating complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core pvc insulated pvc sheathed copper conductor flexible cable 24 / 0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in cm ( 1:4 ) white washing matching with existing color etc complete all as specified and directed by engineer in charge 182 supply and filling in sand for cable protection complete all as specified and directed by engineer in charge 183 supply and lay standard size bricks subclass b type complete all as specified and directed by engineer in charge 184 m&l for fixing gi tubing ( light grade ) 80mm bore for cable protection laid under path / trench / wall / on pole all as specified and directed by engr in charge. 185 supply and lay jointing and testing and commissioning in replacement of 35 sqmmx4 core xlpe insulated, screened , pvc bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & pvc sheathed lt cable 1100 v grade conforming to is 7098 laid in trenches / ducts / fixed on poles wall / laid under roads / paths / drain / culverts or passing through pipes complete all as specified and directed by engineer in charge. 186 m&l for galvanized steel water tubing medium grade of 25 mm bore with & including all fittings complete, laid in trenches / wall or floor , and connections of 25 mm bore, complete all as specified and directed by engineer in charge. 187 supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 100mm bore gi / di water pipe line including drilling and welding of 15 25mm gi socket and necessary rubber insertion, nut, bolts & washers complete all as specified and directed by engineer in charge. 188 s&f 20mm bore gun metal gate valve ( isi marked ) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete all as specified and directed by engineer in charge. 189 m&l for cutting existing steel tubing for alterations or additions for 40mm to 50 mm size screwing existing steel tubing for alterations or additions ( or lengthening screw on pipe to form connector ) complete all as specified and directed by engineer in charge. 190 s&f 25mm bore gun metal gate valve ( isi marked ) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete all as specified and directed by engineer in charge. 191 supply, fixing , testing & commisioning of electric chimney ( 90 cm ) with feature of baffle filter, inbuilit light, touch screen control panel, noise level, 58 db, stainless steel body, air suction capacity 1200 cmh, speed level 3 , motor power 180 watt, input vol 220 240 v / 50hz, remote controlled and fitting in wall as connecaled or duct all as specified and directed by eng in charge. 192 supply and fixing of ms powder coated fly catchers machine with dimensions ( l 24.5 x d 5.5 x h 17 ) , light source philips actinic uv tubes ( two tubes ) , capacity of 18 watt each of tube all as specified and directed by engr in charge. 193 note : ( i ) amount ofcredit for retrieved materials is mentionedin sch a section ii of tender documents in pdf form which will be deducted while acceptance of tender offline....

Due Date : December 14, 2023

Tender Value : ₹ Ref. Documents

View Tender
5
Indian Army - Rajasthan

40736528 bids are invited for synthetic enamel paint og , synthetic enamel paint black , synthetic enamel paint dark brown , synthetic enamel paint sand color , synthetic enamel paint brown , synthetic enamel paint white , synthetic enamel paint blue , synthetic enamel paint yellow , synthetic enamel paint green , synthetic enamel paint red , thinner , turpentine oil , brush 2 inch , brush 4 inch , fevicol , red oxide primer , oil bound distemper obd , screw full threaded 50mm packet of 100 nos , ply 8 feet x 4 feet x 6mm thick , terracotta , lime , geru , sintex tank 1000 ltr capacity , sintex tank 500 ltr capacity , sds screw 50mm packet of 100 nos , glass putty , jk white putty , pvc looking mirror 600mm x 450mm , urinal waste pipe 40mm , vitreous china urinal pot of standard size including waste pipe comma ci bracket and connection pipe. , shower rose 75mm dia cp designer type , cp brass conceal valve 15mm dia , thread seal teflon tape , cp stop cock 15mm , float valve 20mm , float valve 15mm , gi pipe 15mm dia , pvc connection 450mm long , cp pillar cock 15mm , m seal 200gm , flushing cistern , cp bib cock 15mm , vitreous china wash hand basin with stand , sliding bolt 200mm long , tower bolt 150mm long , door stopper , hydraulic door closure , window glass pane 1 feet x 1 feet x 4mm thick , window handle , flush door with shutter with fly mesh shutter of size 1000x2160mm century or greenply , steel window pegset , wire mesh for door or window , double door shutter , acrylic sheet 2 feet x3 feet , door handle , cement opc 43 gde , sand coarse , aggregate 20mm gde , aggregate 40mm gde , aggregate 10 to 20mm gde , white cement , cgi sheet 3 feet x10 feet , ppgi sheet 0 point 5mm thick 8 feet x 4 feet , ppgi sheet 0 point 5mm thick 10 feet x 4 feet , pbs roll 1m wide x 20m long , floor tile 600mm x 600mm , floor tile 400mm x 400mm , floor tile 300mm x 300mm , false ceiling panel 600x 600mm total quantity : 2046...

Due Date : November 23, 2023

Tender Value : ₹ Ref. Documents

View Tender
6
Indian Army - Rajasthan

40595070 bids are invited for provision of miscellaneous maintenance store float valve 20mm , float valve 15mm , gi pipe 15mm dia , pvc connection 450mm long , cp pillar cock 15mm , m seal 200gm , flushing cistern , cp bib cock 15mm , vitreous china wash hand basin with stand , sliding bolt 200mm long , tower bolt 150mm long , door stopper , hydraulic door closure , window glass pane 1 feet x 1 feet x 4mm thick , window handle , flush door with shutter with fly mesh shutter of size 1000x2160mm century or greenply , steel window pegset , wire mesh for door or window , double door shutter , acrylic sheet 2 feet x3 feet , door handle , cement opc 43 gde , sand coarse , aggregate 20mm gde , aggregate 40mm gde , aggregate 10 to 20mm gde , white cement , cgi sheet 3 feet x10 feet , ppgi sheet 0 point 5mm thick 8 feet x 4 feet , ppgi sheet 0 point 5mm thick 10 feet x 4 feet , pbs roll 1m wide x 20m long , floor tile 600mm x 600mm , floor tile 400mm x 400mm , floor tile 300mm x 300mm , false ceiling panel 600x 600mm total quantity : 2046...

Due Date : November 20, 2023

Tender Value : ₹ Ref. Documents

View Tender
7
North Western Railway - Rajasthan

40343491 auction sale of old abandoned quarters ,released masonry stone,980 cum, release stone patti,1650sqm,released rail,23.648mt,steel jaffery,6.933mt,wooden door,4 mt,steel door,9.850mt,wooden ventilator,0.400mt,wooden window ,0.800mt,steel window,0.600mt,miscellaneous steel ,500 kg...

Due Date : October 30, 2023

Tender Value : ₹ Ref. Documents

View Tender
10
Prasar Bharati - Rajasthan

39997773 tender for providing and fixing wire gauge steel window in 1 no. type e quarter (ground floor) at akashvani, suratgarh...

Due Date : October 10, 2023

Tender Value : ₹ 1.11 Lakhs

View Tender
11
North Western Railway - Rajasthan

39685596 auction sale of abandoned 48 nos type i quarters, released rails us (rm) 41/1aprox. wt2566.08 kg,released rails us 50r aprox. wt 491.04 kg, released rubble stones 897.99 cum, released stone slab 617.10 sqm, released half bricks 297.04sqm, released wooden windows 24 nos, released wooden doors 36 nos, released u/s steel jeffery 132.90 kg, released ac sheets47.61sqm,released steel girders 3516.48 kg, released steel doors of different sizes 1125 kg, released steel window 360 kg,...

Due Date : September 19, 2023

Tender Value : ₹ Ref. Documents

View Tender
12
Military Engineer Services - Rajasthan

39565805 tender for repair /maintenance of wooden doors and windows,steel windows, cupboards and repair to approach path, hardstanding, drain cover etc in domastic area at air force station jaisalmer...

Due Date : October 02, 2023

Tender Value : ₹ 45 Lakhs

View Tender
13
Indian Army - Rajasthan

39278199 bids are invited for synthetic enamel paint og , synthetic enamel paint black , synthetic enamel paint dark brown , synthetic enamel paint sand color , synthetic enamel paint brown , synthetic enamel paint white , synthetic enamel paint blue , synthetic enamel paint yellow , synthetic enamel paint green , synthetic enamel paint red , thinner , cement opc 43 gde , sand coarse , aggregate 20mm gde , white cement , fevicol , red oxide primer , oil bound distemper obd , screw full threaded 50mm 100 nos , nails full threaded 150mm , nails 100mm , nails 75mm , nails 50mm , nails 25mm , ply 8 feet x 4 feet x 6mm thick , ppgi sheet 0 point 5mm thick 8 feet x 4 feet , ppgi sheet 0 point 5mm thick 10 feet x 4 feet , terracota , lime , geru , pbs roll 1m wide x 20m long , sds screw 50mm 100 nos , sds screw 25mm 100 nos , termite solution , glass putty , jk white putty , pvc looking mirror 600mm x 450mm , towel rail 600mm long , urinal waste pipe 40mm , cp stop cock 15mm , float valve 20mm , float valve 15mm , gi pipe 15mm dia , pvc connection 450mm long , cp pillar cock 15mm , m seal 200gm , flushing cistern , cp bib cock 15mm , sliding bolt 200mm long , tower bolt 150mm long , hydraulic door closure , window glass pane 1 feet x 1 feet x 4mm thick , window handle , steel window pegset , wiremess for door or window , acrylic sheet 2 feet x 3 feet , door handle , led tube light fitting 9 or 10w , led tube light fitting 18 or 20w , led bulb 10w , led bulb 12w , lt ug cable 10 sqmm 2 core , multistranded copper cable of size 1 point 5 sqmm , casing n capping 25mm , db spn double door 8 way , mcb spn 40a dp , pt switch 5a , piano type switch 15a , socket 5a , socket 15a , ss combination 5a with box , ss combination 15a with box , bulb holder , fan eloctroic regulator , flexible wire twin twisted , mcb 6 to 3...

Due Date : August 25, 2023

Tender Value : ₹ Ref. Documents

View Tender
14
Rajasthan Housing Board - Rajasthan

39114072 item 2 additional a / f for additional and alteration work of sewer and water pipe and steel window including repair work at rental houses jyoti nagar and jawahar nagar, jaipur...

Due Date : August 21, 2023

Tender Value : ₹ 14.44 Lakhs

View Tender
15
Department Of Defence - Rajasthan

39042261 bids are invited for stone boulders , stone metal 40 mm , stone chips 20 mm , stone chips 10 mm , sand , bricks first class , steel window desert coolers, tank cap min 110 l, height min 4 ft, motor material copper, air throw coverage 60 feet, cooling medium wood wool , electric ceiling fan 1200 mm sweep bldc, 5 star make havells , ismb for slab size 150 mm x 75 mm x 6 mtrs long , jambo tent coolers, normal air delivery 5000 cum per hour, fan size 450 mm, minimun weight 50 kgs, size 1135x700x1790 mm, floor standing with integral castor wheels, warranty 01 year , water pump 05 hp diesel engine along with suction pipe 50 mtrs and delivery pipe 50 mtrs complete with foot valve , electric operated diamond chain saw, bar length 20 inch net wt 4 5 kgs, output 2100 watts, make bosch , monoblock motor pump 7pt 5 hp 3 phase , mattress size 1905 x914 x 100 mm minimum thickness , oxygen gas , acetylene gas , right angle coupler, suitable for 50 mm dia pipe, best quality , swivel coupler, suitable for 50 mm dia pipe, best quality , pvc socket 6 inch dia , pvc pipe 6 inch dia , pvc elbow, bend 6 inch dia , rolling steel shutter size 2.75 mtr x 3 mtr with all accessories , door with ms angle frame size 1200 mm x 2100 mm with 19 mm ply wood shutter complete with sliding bolt, tower bolt and door stopper, size of angle iron 35 mm x 35 mm x 5 mm , door with ms angle frame size 900 mm x 2100 mm with 19 mm ply wood shutter complete with sliding bolt, tower bolt and door stopper, size of angle iron 35 mm x 35 mm x 5 mm , door with ms angle frame size 750 mm x 1900 mm with 19 mm ply wood shutter complete with sliding bolt, tower bolt and door stopper, size of angle iron 35 mm x 35 mm x 5 mm , steel window size 1500 mm x 1200 mm with ms angle frame, double shutter 4 mm glass and wire mesh fitted, complete with tower bolt and window stopper , steel window size 1200 mm x 900 mm with ms angle frame, double shutter 4 mm glass and wire mesh fitted, complete with tower bolt and window stopper , steel ventilators, v 1 having size 600 mm x 300 mm , wc indian type , pvc cistern 10 ltrs cap , pvc pipe 110mm dia 6 mtr long , plastic jerricane 60 ltrs cap , plastic jerricane 35 ltrs cap , plastic jerricane 20 ltrs cap , plastic jerricane 10 ltrs cap , plastic jerricane 5 ltrs cap , steel jerricane 20trs cap , steel conical measuring can half ltr cap , steel conical measuring can 1 ltr cap , steel conical measuring can 2 ltr cap , steel conical measuring can 5 ltr cap , steel conical measuring can 10 ltr cap , rotary oil pump 12 mtrs head and max flow rate 250 ml in one rotation , plastic barrel pump model emk 12 , lever action barrel pump, cap 50 210 ltrs , steel funnel 05 ltrs cap , smart funnel with dust cap plastic 5 ltrs cap , drum wrench with high strength cast alluminium body, ideal for opening all types of drums total quantity : 26724...

Due Date : August 10, 2023

Tender Value : ₹ Ref. Documents

View Tender
16
Military Engineer Services - Rajasthan

38911722 tender for welcome maintenance of offers married accommodation in central area at ge nasirabad. 1 m & l for preparation of old plastered or unplastered surfaces of wall including cornices etc applying one coat of white wash complete all as specified and directed. 2 all as per srl item no 1.00 here in before but one coat of white wash on ceiling 3 m & l for washing rubbing down and stopping distempered surfaces of wall and applying one coat of oil bound distemper white or tinted complete all as specified and directed. 4 m & l for complete removal of existing treatment of old plastered surface of wall andapplying two coats of oil bound distemper over a coat of 1mm thick putty ( jk / birla ) complete all as specified and directed. 5 m&l for preparation of old surface of wood and wood based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint ( 1st quality ) complete all as specified and directed. 6 m&l for preparation of old surface of steel or iron based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint ( 1st quality ) complete all as specified and directed. 7 m & l for washing rubbing down and stopping of old painted surfaces, removing nails, making good holes, cracks etc and applying one coat of cement base paint complete all as specified and directed. 8 m & l for complete removal of existing treatment and applying two coats of weather proof acrylic emulsion paint over a coat of 1mm thick wall care putty including a coat of emulsion wall primer all as per manufactures instructions complete all as specified and directed.make : asian, apex and berger or equivalent as approved by ge 9 m & l for complete removal of existing treatment of oldsurface of manglore tiles and applying two coats of terracotta roof paint complete all as specified and directed. make : apex / berger 10 taking down cement or cement lime plaster from stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 11 dismantling floor, hearth or wall tiles including cement mortar and rubbish off the premises, complete all as specified and directed. 12 demolition of brick / stone masonry built in cement or cement lime mortar in any description complete all as specified and directed. 13 demolition of cement concrete ( unreinforced ) in floors and paving n.exc 15cm thickness ( above or below ground level ) complete all as specified and directed. 14 hacking out old broken glass ( any thickness, size quality or description ) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new ones and s&f 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 15 hacking out old broken glass ( any thickness, size quality or description ) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new ones and s&f 3.00 mm thick figured glass, ordinary quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 16 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) n. exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar ( 1:3 ) complete all as specified and directed. 17 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) exc 1.50 sqm and n.exc 4.00 sqm each and removing from site complete and making good disturbed surfaces of wall in cm ( 1:3 ) complete all as specified and directed. 18 taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf and removing from site complete all as specified and directed 19 m & l for rendering 15mm thick in cm ( 1:6 ) on stone masonry surfaces wall finished even and smooth without using extra cement or surface other than fair face of brick work or on one side of lathing complete all as specified and directed. 20 m & l for rendering 10mm thick in cm ( 1:3 ) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. 21 m & l for 15mm thick rendering in cm ( 1:4 ) on brick / concrete surface mixed with water proofing compound @ 3% by weight of cement & surface fair and even complete all as specified & directed. note : wpc will be measured and paid separately 22 m & l for 15 mm thickrough cast plaster mix with crusted stone ( 6 10 mm ) , sand and cement in the ratio 1:1:1 , over 10 mm thick rendering in cm 1:4 as in under coat including dubbing coat ( if required ) complete all as specified and directed. 23 m&l for stone walling of random rubble, uncoursed, well bonded, bedded & solidly hearted, built in cm ( 1:6 ) complete all as specified and directed. 24 all as per sl item no 23.00 here in before but except stones.note: old servieable stones retrieved vide sl item no 12.00 shall be reused. 25 m & l for brick work with fly ash bricks, straight or curved on planto any radius, in half brick thick wall built in cm 1:4 complete all as specified and directed. 26 m & l for brickwork with fly ash bricks, old size, straight or curved on plan exc 6 m mean radius, built in cm 1:6complete all as specified anddirected. 27 dismantling loose / disintegrated portion of rcc chajjas bends shelves, beams balconies and similar work at any position or any height and dubbing out with pcc ( 1:1.5:3 ) , 15mm to 50mm thick using 6 to12mm graded stone aggregate to make up and finished to required shape including applying anti corrosive paint on exposed surface of reinforcement, provision of necessarysupports, form work and 10mm thick plastering in cm ( 1:4 ) finished fair and even complete all as specified and directed. 28 m&l 25mm thick pcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate as in floorcomplete all as specified and directed. 29 m & l for non skid ceramic coloured tiles ( joint free ) , 7 to 8 mm thick ( square / rectangular ) , area of each tile exc 0.18 sqmbut not exc 0.38 sqmin floors etc set and jointed in neat cement slurryand pointed inwhite cement mixed with pigments to match the shade of tile laid over and including screed bed 15 mm thick in cm ( 1:6 ) complete all as specified and directed. 30 m & l for non skid ceramic coloured tiles ( joint free ) , 7 to 8 mm thick ( square / rectangular ) , area of each tile exc 0.11 sqmbut not exc 0.18 sqmin floors etc set and jointed in neat cement slurryand pointed inwhite cement mixed with pigments to match the shade of tile laid over and including screed bed 15 mm thick in cm ( 1:6 ) complete all as specified and directed. 31 m & l for vitrified ceramic tiles light shade 10mm thick ( square / rectangular ) polished area of each tiles exc. 0.18 sqm but n.exc 0.36sqm in floor, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tile laid over and including screed bed 15mm thick in cm ( 1:6 ) complete all as specified and directed. 32 all as per sl item no 31.00 here in before but on vertical surfaces of stone wall such as dados, skirting etc set& jointed in neat slurry and pointed inwhite cement mixed with pigments to match the shade of tile over & including 10 mm thick screed plaster in cm 1:4 complete all as specified and directed. 33 m & l for glazed ceramic coloured tiles, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces of wall such as dados, skirtingsetc set and jointed in neat cement slurry and pointedin white cement mixed with pigments to match with the shade of tile over and including 10mm thick screed plaster in cm ( 1:4 ) complete all as specified and directed. 34 all as per sl item no 29.00 here in before but on vertical surfaces of stone wall such as dados, skirting etc set& jointed in neat slurry and pointed inwhite cement mixed with pigments to match the shade of tile over & including 10 mm thick screed plaster in cm 1:4 complete all as specified and directed. 35 m&l for 16 18 mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platform and like set & jointed in neat cement slurry & pointed in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite including rounding the exposed edgeslaid over & including 15mm thick screed bed in cm ( 1:6 ) complete all as specified and directed. 36 m & l for rolled mild steel work angle iron ( 40x40x6mm ) as in door frame ( chowkhats ) including provn of 10mm dia deformed bar welded horizontally to bottom of frame confirming to fe 210 gde e 165 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed 37 s & f second class hw ( hollock / bansum / sal ) , plain, solid, straight, chowkhats & frames, wrought, framed, rebated on the solid, rounded or chamfered, put together glue pinned at joints complete all as specified and directed. 38 s & f hold fast of flat iron 25x6mm conforming to fe 210 gde e 165including preparing the surfaces & treated with coaltar & sanded with clean sharp sand complete all as specified & directed 39 raking out joints / pointing to random rubble or polygonal rubble stone masonry uncoursed or brought upto courses built in cm and m & l for raised pointing in cement mortar ( 1:4 ) complete all as specified and directed. 40 taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf& refixing in the same opening after necessary resecuring or easing & adjusting etccomplete all asspecified and directed. 41 taking down shutters of any description exc 2 sqm each leaf& refixing in the same opening after necessary resecuring or easing & adjusting etc complete all asspecified and directed. 42 s & f 30mm thick flush shuttersolid core construction with block board core and ply wood face panels with commercial face on both sides including 6mm thick iind class hard wood lipping on edges complete all as specified and directed. 43 s & f second class hw hollock / bansum / sal, 35 mm thick, glazed and skeleton shutters, factory made open rebated ( three panels ) and prepare to receive glass, gauge etc without sash bar, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. size of members of shutter shall be as specified in ssr part i, section 8 clause 8.24 ( a ) member shall be kiln seasoned & chemically pressure treated complete all as specified and directed. 44 s&f factory made pvc solid frame of size 50mmx47mm made out of 5mm prelam pvc sheet & edges will be painted to match with prelam sheet reinforced with m.s. square tube and fixing in opening as per specification & drawing as perssr 2020 complete all as specified and directed. 45 s & f factory made solidpvc mouldeddoor shutter with wood free eps, 28 to 30mm thick, ( styles ) with 2 raised panel design with 2mm thick moulded prelaminated pvc sheeton front face & 2mm thick plain colour pvc sheet on back face, and fixing in the frame at site as per specification and drawings on page 161 of ssr ( part ii ) 2020 complete all as specified and directed. 46 s & f in repair steel window / ventilator factory made, made out of ms hollow section 79mmx39mmx1.6mm thick frame with double shutters ( glazed & wire gauge shutters ) made out of z section using flush butt welding & tenon riveting all as per is 1038 / 83, dobby hinges shall be provided to both shutters. locking arrangements as per sample approved by ge, provided with knob, 10mm ms square bars in grills, z section handle 100mm sized & 150mm long hook & eye welded to frame & shutter, four nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fasts and making good in pcc 1:2:4 type b 1 including preparation of surfaces & applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed.note : wire mesh and sheet glass shall be measured & paid separately under respective items. 47 taking down of old boards and s & f 18 / 19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination, fixed with screws including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works complete all as spepcified and directed. 48 s & f aluminium alloy, anodised sliding door bolt, 300mm long, isi marked, with hasp and staple ( bolt type ) and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed. 49 s & f in repairs aluminium alloy, anodised sliding door bolt, 300mm long, isi marked, with hasp and staple ( bolt type ) and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed. 50 s&f mild steel butt hinges, medium weight, cold rolled, isi marked of size 125 mm complete all as specified and directed. 51 s&f in repairs mild steel butt hinges, medium weight, cold rolled, isi marked of size 125 mm including necessary welding work etc complete all as specified and directed. 52 s&f aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 53 s&f in repairs aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 54 s&f 150 mm long extruded aluminium alloy handle fabricated type anodized complete all as specified & directed. 55 s&f in repairs 150 mm long extruded aluminium alloy handle fabricated type anodized complete all as specified & directed. 56 s & f stainless steel wire cloth0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed 57 s & f in repairs stainless steel wire cloth0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed 58 s & f in repairs floor door stopper aluminium alloy body & tongue of size 140mm, anodised with hard drawn spring, fixed in door, over all length of cover plate of complete all as specified and directed. 59 taking down the existing material and s&f 300 mm rat tail rod mild steel ordianarypattern springs including roller and roller plate complete all as specified and directed. 60 s & f in repairs 100mm size hasp and staple, aluminium anodised, safety type including bolt to hinge plate complete all as specified and directed 61 s & f in reapirs25mm dia ms chromium plated curtain rod powder coated tubular, fancy type, complete all as specified and directed. 62 s&f in reapirs ms chromium plated powder colour coated, decorative type knobs with bracket fixed at end of pelmet rod suitable for 25mm dia complete all as specified and directed. 63 dismantling of exisiting unserviceable rcc / pvc water tank of capacity not exceeding 500 litre each s&f 500 litre capacity rotational moulded polyethylene water storage tanks double layered ( cylindrical vertical with closed top ) isi marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in ssr part i. 64 dismantling of exisiting unserviceable rcc / pvc water tank of capacity not exceeding exc 500 but n. exc 1000 litre each s&f 1000 litre capacity rotational moulded polyethylene water storage tanks double layered ( cylindrical vertical with closed top ) isi marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in ssr part i. 65 taking out old unserviceable water closet ( squatt pattern ) and s & f vitreous china, squatting panorissa pattern size 580x440mm, white with integral foot rests ( excluding flushing cistern and flush pipe ) with chinaware ‘p’ or ‘s’ trap, front or back inletincluding connection to trap and to flushing pipe, anti syphonage pipe and making good the floor to match the existing completeall as specified and directed. 66 taking out old unserviceable water closet and s & f vitreous china wash down closet pan ( pedestal pattern ) , white, including plastic cover white closed pattern whith flat bottom and mild steel chromium plated / pvc hinge device including connections to drain ( or outgoing pipe ) and to flushing pipe, anti syphonage pipe etc complete all as specified and directed. 67 taking down old unserviceable whb and s&f vitreous china, white, wash hand basin flatback of size 550 x 400mm complete all as specified and directed 68 demolition of cement concrete ( unreinforced ) in any position & of any description from sunken floor ( ground or 1st floor ) and removing and depositing materials exc 50mtrs level not exc. 1.5m above the starting point complete all as specified and directed. 69 m & l for cement concrete 1:5:10 type e2 using 40mm graded stone aggregate as in sunken floors filling and mass concrete complete all as specified and directed. 70 m&l 20mm thick cement plaster in cm 1:4 mixed with water proofing compound @ 3% and applying water proffing treatment on sunken portion with acrylic based polymer modified cementitious composit compound as specified and approved & cement slurry two layers, 1st layer @ 0.488 kg / sqm mixed with composit compound @ 0.253 kg / sqm & the second layer slurry @ 0.242 kg / sqm mixed 0.126 kg of compound complete with min 4 hours allowed to air cure between these layers and applying 200 polyflim with adhesive complete all as specified and directed. 71 m&l for 50mm thick pcc ( 1:3:6 ) type c 1 using 20mm graded stone aggregate as in plinth protection finished fair and even laid in alternatebays n.exc 2m in length and joints filled with bitumen mastic 1:3 ( 1 bitumen :3 sand ) complete all as specified and directed. 72 s & f in repair pvc valve less, syphonic action type flushing cistern, isi marked, 10 litre capacity, low level, white / ivory colour, with inlet, ball valve, float, handle fixed with pvc rawl plug of suitable size complete all as specified and directed. 73 s & f in repair pvc flush pipe of approved quality 32 mm bore, for low level flushing cistern complete all as specified and directed. 74 s & f in repair brass chromium plated shower rose of 100mm size with swivel joints, including fixing to steel pipe or union complete all as specified and directed. 75 taking down old unserviceable pvc connectionand s & f pvc connection, heavy duty 15 mm bore, 45 cm long with two nos ptmt nuts at both ends of approved quality complete all as specified and directed 76 s&f in repair pillar tap, 15mm bore, cast copper alloy, chromium plated, isi marked, screwed down high pressure with or without lettred hot or cold with long screw shanks and fly nuts screwed for iron pipe complete all as specified and directed 77 s&f in repair stop / angle valve 15mm bore cast copper alloy, chromium plated, isi marked with long crutch or butterfly handle screwed down high pressure screwed both ends for iron pipe complete all as specified & directed. 78 s&f in repairs 25mm bore gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipes and fixed all as directed. 79 taking down old unserviceable waste pipe and s&f 32mm bore pvc waste pipe of 75mm length with oneend socketed complete all as specified and directed. 80 s & f in repairs grating square / round 140mm size of ptmt with centre hole movable or side hole for fix to waste pipe ( minimum weight 50 gms ) complete all as specified and directed. 81 s & f in repairs 15 mm bore bib taps standard of ptmt any colour, screwed for iron pipe and fixed complete all as specified and directed. 82 taking down old unserviceable water closet seat cover & s&f plastic water closet seat cover, white, closed pattern with flat bottom and cover & mild steel chromium plated or aluminised hinging device complete all as specified and directed. 83 taking down old unserviceable kitchen sink and s&fkitchen sink with drainage board overall size not less than 915x460mm, bowl size 410x 330x160mm made of stainless steel 1.00 mm thick with plugs, washers and waste including fixing cantilever brackets and connecting union complete all as specified and directed.note : minor variation in dimension + 20mm as per standard catalogue of manufacturer may be approval of ge in writing without price adjustment. 84 s & f in repairs stainless steel plate rack made of 0.50mm thick of over all size914mm x 609 mm x 255 mm and weight not less than 7.00 kg each of approved quality complete all as specified and directed.note : minor variation in dimension may be permitted as per standard manufacturing models of manufacturer without price adjustment with prior approval of ge but weight shall not be less than 7.00 kgs. 85 s & f waste coupling cp 32mm dia for glazed ware basins etc with long screwed shanks and fly nuts flanged etc complete all as specified and directed. 86 s & f in repair bib taps isi marked, cast copper alloy, chromium plated, isi marked with crutchor butterfly handle, screwed down, screwed for iron pipeor for brass ferrule and fixed for 15 mm boreof pipe complete all as specified and directed. 87 s & f in repair pvc ( swr ) floor trap with grating 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed. 88 taking down old unserviceable mirror and s & f looking mirror of size 600 mm x 450 mm x 5.5mm thickof selected quality, mounted on pvc frame and fixed to and including wooden plugs with chromium plated brass screwswasher cup washer complete all as specified and directed. 89 s & f in repair tubular towel rail, chromium plated brass 20mm dia ‘d’ type 60cm long between flanges complete all as specified and directed. 90 s & f in repair for toilet fittings chromium coated towel rack 600mm long without lower haners but three hookscomplete all as specified and directed. 91 s & f in repair brass wall mixer 15mm bore cast copper alloy chlromium plated wall each mixer with hot and cold water with crutch handlecomplete all as specified and directed. 92 s & f in repair for toilet fittings corner glass shelf with bracket complete all as specified and directed. 93 s & f in repair for toilet fittings wall mixer ( wall mounted model ) with teliphonic shower rose complete all as specified and directed. 94 s & f in repair for toilet fittings wall teliphonic shower with 1.5 mtr long flexible tube & swivel wall hookcomplete all as specified and directed. 95 s & f in repair for toilet fittings health faucet with 1.2mtr long flexible tube & swivel wall hook complete all as specified and directed. 96 s & f in repair for pvc cabinet of size 422mm x 622mm with mirror of good quality with shelves in bath fixed complete to wallscomplete all as specified and directed.make : prayag cat no. 555 or make and model are equivalent as approved by ge. 97 s & f in repair for toilet fittings two way bib cock of 15mm bore complete all as specified and directed. 98 taking up or down steel tubing and connection 15mm bore keeping aside for reuse or removingto store complete all as specified and directed. 99 all as per srl item no 98.00 here in before but 20mm bore 100 all as per srl item no 98.00 here in before but 25mm bore 101 supply and fix mild steel water tubing 15 mm dia galvanised medium grade including all fittings ( such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc ) and fixed to walls / ceilings / laid on floors including testing complete all as specified and as directed. 102 all as per srl item no 101.00 here in before but 20mm bore 103 all as per srl item no 101.00 here in before but 25mm bore 104 refixing only 15mm bore old gi tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, tee, union, socket, reducer etc complete all as specified and directed. 105 all as per srl item no 104.00 here in before but 20mm bore 106 all as per srl item no 104.00 here in before but 25mm bore 107 supply only liquid water proofing compound, isi marked complete all as specified & directed 108 m&l in repairs for 2nd class hard wood plain fillets, square , rectangular or triangular area exec. 6 sqcm but n. exec 13 sqcm in sectional, clean sawn, secured with nails complete all as specified and directed. 109 s & f in repairs 75mm bore pvc ( swr ) pipe single socketed in any length with rubber ring joints fixed to wall isi mark, complete all as specified and directed. 110 s & f in repairs 110mm bore pvc ( swr ) pipe single socketed in any length with rubber ring joints fixed to wall isi mark, complete all as specified and directed. 111 s & f in repairs 75mm bore pvc ( swr ) bend / shoe with oval access door of any radius complete all as specified and directed. 112 s & f in repairs 110mm bore pvc ( swr ) bend / shoe with oval access door of any radius complete all as specified and directed. 113 s&fin repair 75mm bore pvc ( swr ) junction single ( single t ) equal or unequal complete all as specified and directed. 114 s & f in repairs 110mm bore pvc ( swr ) junction single ( single t ) equal or unequal complete all as specified and directed. 115 m&l for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over & including one coat of 1mm thick cement putty complete all as specified & directed.. 116 m&l for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified & directed. 117 m & l for preparation of newly plaster surfaces of wall& applying two coats of cement base paint over a coat of primer complete all as specified and directed. 118 m&l for preparation of new steel surfaces of any description over 10 cm width or girth applying two coats of synthetic enamel paint ( 1st grade ) over a coat of red oxide primer complete all as specified. 119 m&l for preparing the new wooden surface of any description over 10 cm width or girth & applying two coats of synthetic enamel paint ( 1st grade ) over one coat of pink primer complete all as specified & directed. 120 s&f in repair jet flush including plate and coonection pipe complete all as specified and directed. 121 m&l for machine cut kota stone slab flooring of size 550mm x 550mm 20 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishinglaid over & including 15mm thick screed bed in cm 1:6 complete all as specified & directed. 122 m&l for kota stone slab 20 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing in riser of steps, skirting, dado and pillar laid over & including cement screed 10mm thick in cm ( 1:4 ) complete all as specified & directed. 123 only on old surfacesmirror polishing on marble / granite / kota stone where ever required to give high gloss finish complete all as specified & directed. 124 m&l for crack repair in wall, ceiling and roof with cm 1:3 mixed with water proofing compound @3% by weight of cement, width of crack is 25mm and 50mm deep including necessary demolition and making good disturbed surfacecomplete all as specified & directed.note : wpc measured and paid separately 125 supply and fixing in repairs18mm thick ( one side decorative lamination & other side balancing lamination sheet density 600kg / m3 ) solid pvc board with edge bending on edgeswith cement solvent adhesive for shutter / kitchen cabinet / cup boards / partition wall / wall cabinet and similar work completeall as specified and directed. make : rajshree / kitply / century or equivalent as approved by ao. 126 supply and fixing in repairs12mm thick ( one side decorative lamination & other side balancing lamination sheet density 600kg / m3 ) solid pvc board with edge bending on edges with cement solvent adhesive for shutter / kitchen cabinet / cup boards / partition wall / wall cabinet and similar work complete all as specified and directed.make : rajshree / kitply / century or equivalent as approved by ao. 127 s&f stainless steel soft close hinge with assembly, complete all as specified and directed.make : godrej code no. 5070 128 s&f 125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed. 129 s&f stainless steel basket ( plain ) of approved quality of size 520 x 485 x 100mm complete all as spepcified and directed. make : godrej ss 304 code no. 6154 130 s&f stainless steel plate / thali basket of approved quality of size 520 x 485 x 200mm complete all as spepcified and directed. make : godrej ss 304 code no. 6168 131 s&f stainless steel cutlery basket of approved quality of size 520 x 485 x 100mm complete all as spepcified and directed. make : godrej ss 304 code no. 6162 132 s&f stainless steel cup & saucer basket of approved quality of size 520 x 485 x 100mm complete all as spepcified and directed. make : godrej ss 304 code no. 6159 133 s&f stainless steel two shelf pull out basket of approved quality of size 150 x 485 x 430mm complete all as spepcified and directed. make : godrej ss 304 code no. 6169 134 s&f steel ball bearing basket / trolly / drawer channel 50cm long complete all as spepcified and directed.make : godrej code no. 8178 135 total in figures 136 quoted amount in words...

Due Date : August 26, 2023

Tender Value : ₹ 40 Lakhs

View Tender
17
Military Engineer Services - Rajasthan

38911633 special repair to building no. p 54 1 to 4 jco md accn at tower colony of rkt regt pinaka and spl repair and addn / altn of bldg no 95 of 97 ad gp sp wksp under ge nasirabad spl repair to bldg no. p 54 1 to 4 jco md accn at tower colony of rkt regt pinaka and spl repair and addn / altn of bldg no 95 of 97 ad gp sp wksp. 1 taking down cement or cement lime plaster on stone / brick wall, ceiling incl. raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 2 m& l for rendering in cement mortar ( 1:6 ) , 15mm thick on stone masonary surfaces finished fair and even complete all as specified and directed. 3 m&l for rendering 15mm thick in cm 1:4 on stone masonry, external surfaces finished fair & even complete all as specified and directed. 4 m&l for rendering in cement mortar ( 1:3 ) 5mm thick as on ceiling surfaces finished even and smooth without using extra cement, complete all as specified and directed. 5 dubbing out average 10mm thick in cm 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed. 6 m&l for preparation of new plastered surfaces of wall and applying two coats ofoil bound distemperover a coat of1mm thick wall care putty complete all as specified and directed. 7 m&l for preparation of new plastered surfaces of ceiling and applying three coats ofwhite wash complete all as specified and directed 8 m&l for preparation of old plastered surfaces of ceiling and applying two coats ofwhite wash complete all as specified and directed 9 m & l preparation new decorated surfaces of wallsand providing two coat of cement base paint over a coat of primer, complete all as specified and directed. 10 m & l for complete removal of existing treatment of old plastered surfaces ofwall and applying two coats of oil bound distemper over & including 1mm thick ( jk / birla ) white putty complete all as specified and directed. 11 m & l for preparation of old wooden surfacesof any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 12 m & l for preparation of old concrete surfaces of kerb stone etc over 10cm in width or girth and applying two coats of synthetic enamel paint, alternate in black & white tint, all as specified & as directed. 13 m & lfor preparation old decorated surfaces of wallsand providing one coat of cement base paint complete all as specified and directed. 14 demolition of cement concrete ( unreinforeced ) in floors and paving n.exc 15cm thickness ( above or below ground level ) complete all as specified and directed. 15 m&l for machine cut kota stone slab flooring 18 20mm thick over and including 15mm thick screed bed in cm 1:6, laid andjointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 16 m&l for kota stone slab 18 20mm thick in riser of steps, skirting, dado and pillar laid over and including cement screed 10mm thick in cm ( 1:4 ) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishingcomplete all as spd & directed. 17 m&l for cement concrete type d 2, 1:4:8 ( 40 mm graded aggregate ) , 100 mm thick, complete all as specified and directed. 18 m&l for factory made 60mm thick machine pressed precast cement concrete coloured interlocking paver blocks of grade m 35 conforming to is 15658 2006 of shape and size as directed with grey cement andpigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed. 19 m&l for pcc 1:2:4 type b 1 ( using 20mm stone crushed agg. ) as inrounded or chamfered on edges in any description complete all as specified. 20 m & l forbitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5 kg per sq m per coat and applying plythene film black, 50 micron laid in floors complete over sunken floor slab and embedded in side wall / covered fillet complete all as specified and directed.note : supply of water proofing compound shall be measured and paid separately. 21 supply only water proofing compound isi marked complete all as specified and directed. 22 m & l for pcc ( 1:5:10 ) type e 2 using 40mm graded crushed stone aggregate as in sunken floors complete all as specified and directed. 23 m&l forglazed ceramic coloured tiles, size 450 mm x 300 mm, 6 7 mm thick on vertical surfaces of wall such as dados, skirting etc set& jointed in neat slurry and pointed in white or colour cement to match over 10 mm thick screed plaster in cm 1:4 complete all as specified and directed 24 m & l for non skid ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqmbut not exc 0.18 sqmin floors etc set and jointed in neat cement slurryand pointed inwhite or coloured in whiteor colouredcement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in cm ( 1:6 ) complete all as specified and directed. 25 all as per the item no 24.00 above but as in skirting 10 mm screed plaster in cm 1:4 complete all as specified. 26 m&l for 25mm thickpcc 1:2:4 type b 1 ( using 20 mm thick crushed stone aggregate ) as insub base complete all as specified and directed. 27 demolition of stone / brick masonry built in cement or cement lime mortar as in portion orderedand directed. 28 m&l for walling of random rubble, brought upto courses, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & directed. 29 all as per serial item no. 28.00 above but except stone. 30 m&l forbrick work with flyashbricks straight or curved on plan exc 6m mean radius, built in cm 1:6 complete all as specified and directed. 31 m&l for brick work with old size fly ash bricks staright or curved on plan to any radius in half brick thick walls built in cm 1:4, complete all as specified and directed. 32 extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm as specified. 33 demolition of stone slabs & tiles of any description or thickness in floors , aprons etc, complete all as specified and directed. 34 m & l for 18 20mm thick black granite on kitchen platform, window cill and similar work over & including 15mm thick screed bed in cm 1:6 laid over sand stone slabmachine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed. 35 m&l for 50 mm thick pcc 1:3:6 type c1 using 20 mm graded crushed stone aggregate as inplinth protection surface finished fair and evencomplete all as specified. note : plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic ( 1:3 ) . 36 taking down old unserviceable shower rose & s&f brass chromium plated shower rose of 125 mm size withswivel joints, including fixing to steel pipe or union of 15mm bore, mixing valve including three joints to steel pipes or unions and plugging and screwing to walls complete all as specified and directed. 37 taking out old unserviceable water closet ( squatt pattern ) and s&f vitreous china, squatting pan orissa pattern size 580 x 440mm, white with integral foot rests ( excluding flushing cistern and flush pipe ) with vitreous china ‘p’ or ‘s’ trap, front or back inletincluding connection to trap and to flushing pipe, anti syphonage pipe , including pcc ( 1:2:4 ) type b 1 for fixing of wc and making good the floor to match the existing complete all as specified and directed. 38 taking down old unserviceable flushing cistern s&f pvc valveless syphonic action type low level flushing cistern, 10 ltrs capacity . white, with inlet ball valve, float, handlewith 32mm pvc flush pipe, fixed on walls by driling holes and using pvc rawl plug of suitable size complete all as specified and directed. 39 taking down old unserviceable pvc connectionand s & f pvc connection, heavy duty 15 mm bore, 45 cm long with two nos ptmt nuts at both ends of approved quality complete all as specified and directed 40 s&f in repair soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed. 41 taking out old un serviceable tubular towel rail & s&f tubular towel rail aluminium anodised 20mm dia d type 60cm long between flanges complete all as sped & directed. 42 s & f 15mm bore dia stop valves / angle cock, cast copper alloy, isi marked, chromium plated with long shank and cup ( concealed type ) screwed down, light pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the engineer in charge. 43 s&f in repairschromium plated angle stop cock 15 mm diascrewed down light pressure, isi markedscrewed both ends for iron pipe or for union complete all as spd & directed 44 s&f in repairs chromium plated bib taps, with capstan heads, isi marked screwed down for iron pipe or for brass ferrule& fixed for 15 mm bore pipe complete all as specified & directed. 45 s & f for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; in cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to rigid upvc waste pipe bent to shape & fixed to wall with bracket overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the engineer in charge. note : minor variation in dimension + 20mm as per standard catalogue of manufacturer may be approval of ge in writing without price adjustment. 46 taking down old wooden plate rack and s&f stainless steel plate rack made of 0.50mm thick of over all size920mm x 785 mm x 255 mm and weight not less than 7.00 kg each of approved qualitycomplete all as specified and directed.note : minor variation in dimension may be permitted as per standard manufacturing models of manufacturer without price adjustment with prior approval of ge but weight shall not be less than 7.00 kgs. 47 s&f in repairs looking mirror of size 600 x 450 bevelled edgewithselected quality glass mounted on 6 mm thick ac bldg boardor commercial plywood & fixed to wooden plugs with chromium plated brass screw and cup washers.complete all as specified and directed 48 taking down old unserviceable whb and s&fwash hand basin vitreous china white / ivory colour flat size 550 x 400mm fixed including waste coupling, waste pipe , complete all as specified and directed. 49 taking up or down steel tubing and connection 15 mm bore and removing the same from site / keeping aside for reuse complete all as specified and directed. 50 all as per srl itemno. 49.00 above but 20 mm bore. 51 all as per srl item no. 49.00 above but 25 mm bore. 52 s & f water tubing 15 mm bore, medium weight, isimarked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified anddirected. 53 all as per srl item no. 52.00 above but 20 mm bore. 54 all as per srl item no. 52.00 above but 25 mm bore. 55 refixing 15mm bore old gi tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, tee, union, socket, reducer etc complete all as specified anddirected. 56 all as per srl item no. 55.00 abovebut 20 mm bore. 57 all as per srl item no. 55.00 above but 25 mm bore. 58 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) n. exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar ( 1:3 ) complete all as specified anddirected. 59 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) exc 1.50 sqm and n.exc 4.00 sqm each and removing from site complete and making good disturbed surfaces of wall in cm ( 1:3 ) all as specified and directed. 60 m & l for rolled mild steel work angle iron as in door frame ( chowkhats ) & cooler stand including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to fe 290 or fe 330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed. 61 s & f factory made solid pannel pvc door shutter 30mm thick ( style ) consisting of frame made out of ms tubes for top and bottom rail.ms frame shall be covered with heat moulded plain colour pvc c channel having pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour pvc sheet to be fitted in the ms frame welded. sealed to the stiles and rails with suitable pvc sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on ssrpart ii 2020 complete all as specified and directed. 62 s & f second class hw hollock / bonsum / sal35mm thick, factory made, plain framed, paneled shutter ( three panels ) with panels of 9mm thick bwpgrade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to is 710. the size of rails & style shall be as per is 1003 ( part i ) kiln seasoned as per is 1141 & chemically pressure treated as per is 401 complete all as per specified and directed. 63 s & f for 2nd class hw 35 mm thick, gauged and skeleton shutters ( three panels ) , factory made open rebated and prepare to receive glass, gauge etc ( with sash bar ) , edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. size of members of shutter shall be as specified in ssr 2009 part i, section 8 clausemember shall be kiln seasoned as per is 1141 & chemically pressure treated as per is 401 complete all as specified and directed. 64 s&f steel window / ventilator factory made, out of ms hollow section 79mm x 39mmx1.6mm thick frame with double shutter ( glazed & wiregauged shutters ) made out of z section using flush butt welding and tennon riveting all as per is 1038 / 83, dobby hinges shall be provided to both shutters, locking arrangements as per sample approval by ge, provided with knob, 10mm ms square bars in grill, z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in pcc 1:2:4 type b 1, and plaster with finishes to match the existing surfaces, including two coat of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. note : wire mesh and sheet glass shall be measured & paid separately under respective items. 65 m&l18 / 19mm thick block board grade .ii quality, interior grade with decorative type with decorative face veneer on bothface fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed. 66 m & l for 20 to 25 mm thick machine cut kota stone shelves incl rubbing & polishingand set in cm ( 1:4 ) incl cutting inserting into wall not less than 50mm deep and making good to disturbed surfacescomplete all as specified and directed. 67 s & fcontinuous ( piano ) hinges, mild steel, bright finishwidth of flaps ( when open ) 40 mm all as specified and directed. 68 s & fmagnetic ball catcher for cupboard shutters, complete all as specified and directed. 69 m&l for iind class hwplain , solid , straight chowkats and frames sec area n. exe 40 sqcm complete and all as specified. 70 s & f 100mm size hasp and staple, aluminium anodisedsafety type, fixed with screws complete all as specified and directed 71 s & f 75mm size hasp and staple, aluminium anodisedsafety type, fixed with screws complete all as specified and directed 72 s & f in 50 mm dia polished hardwood knobs fixed with screws complete all as specified and directed. 73 s & f for 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all asspecified anddirected. 74 s & f extruded aluminium handle fabricatedtype, anodised 150mm size conforming to is complete all as specified and directed. 75 s&f aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 76 s & f 125mm double action spring hinges, mild steel with steel wire spring, stove enaelled black, completeall asspecified anddirected. 77 s&f mild steel butt hinges, medium weight, cold rolled, isi marked of size 100 mm, complete all as specified and directed. 78 s&f stainless steel wire cloth 0.36mm nominal dia of wire & average width ofaperture 1.40mm & fixed with wire staples complete all as spd & directed. 79 m & l for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of ist quality over a coat of pink primer complete all as specified and directed. 80 m&l for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed. 81 s&f 3.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 82 s&f in repair fancy type 20mm dia aluminium curtainrods powder coated fixed to bracket completed all as spd & directed. 83 s&f in repairs decorative type knobs with bracket of ms powder coated fixing at end of pelmet rod complete al as spd & directed. 84 dismantling of existing unserviceable water tank ofany description capacity exc 250 ltr but n.exc 500trs capacity each complete all as specified and directed 85 supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tanks double layered ( cylindrical vertical with closed top ) isi marked, hoisted and fixed in position and making necessary arrangements for fixing inlet, outlet, over flow pipe & provision of wash out pipe etc complete as specified in ssr part i 86 s&f ball valves ptmt high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete ( minimum weight 210 gm ) complete all as spd & directed. 87 s&fin repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, isi marked complete all as spd & directed. 88 m&l for 40 mm thick sand stone slabs; set and jointed over joists etc. in cm 1:4 as in base of water tank and m&l 25 mm thick pcc 1:2:4 type b 0 ( using 12.5mm stone crushed agg. ) finished concrete surfaces even & smooth complete all as specified and directed 89 taking down existing unservicable treatment of any description including cement plaster / conctrete any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed. 90 m&l for screeding 10mm thick in cm 1:4 on fair faces of rcc / stone patti roof surface finished fair & even without using extra cement even complete all as spescified and directed. 91 m & l for five layered roof treatment with app modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film ( hmhdpe ) protected on both sides with high polymeric asphaltic mix and 20 micron hmhdpe film weight not less than 2.60 kg / sqm applied with bonding material using belown type bitumen conforming to is 702 grade85 / 25 @ 1.20 kg / sqm over bitumen primer conforming to is 3384 @ 0.40 kg / sqm with final coat of bonding bitumen grade 85 / 25 @ 1.20 kg / sqm over app membrane with all overlaps complete all as specified and directed. 92 material and labour for 40mm thick ( average consolidated thickness ) pcc ( 1:2:4 ) type b 0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of v shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of pcc padding and filled with mastic bitumen of ( 1:1 ) proportion complete all as specified and directed. 93 m&l for coved fillet in pcc 1:2:4 type b 0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfacesand surface painted with a hot paving bitumen grade 30 / 40 conforming to is 73 @0.70 kg / sqm over a coat of bituminous primer conforming to is 3384 @ 0.30 ltr sqm complete all as specified and directed 94 taking out of old grill & m & l framed work such as grills, gratings, etc, with ends of bars shouledered and / or reiveted , or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks , cooler stand, and similar work coforming to fe 290m gde e 165 complete all as specified and directed. 95 m&l for pcc 1:3:6 type c1 using 20 mm graded stone aggregateas in surface channel and drain etc complete all as specified and directed. 96 m&l for pcc 1:2:4 type c1 using 40 mm graded stone aggregateas in surface channel and drain etc complete all as specified. 97 s&f in repairs110mm dia upvc rain water pipe fixed on wall under walls as spout incl.complete all as specified and directed. 98 s&f in repairs75mm dia upvc rain water pipe fixed on wall under walls as spout includingcomplete all as specified and directed. 99 s&f only stack clamp out of 50mm by 5mm flat iron and 16 mm dia round iron stays fixed to pipe of bore 100mm complete all as specified and directed. 100 s&f in repair pvc bend / shoe of dia. 110mm complete all as specified and directed. 101 m&l for pcc 1:3:6 , type c 2, using 40mm graded crushed stoneaggregate as in foundation, filling and mass concrete, including necessary formwork, complete all as specified and directed. 102 s & f false ceiling with fibre cement designer tile ivory painted ( high pressure steam cured ) of 4mm thickness ( as per is: 14862 ) of size 595x595 mm and any one of the desin ( occeanic, lake & hill, cascade or electra ) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gms, both side inclusive ) consisting of main t runner with suitably spaced joints to get required length, and 15x32mm made from 0.30 mm thick sheet, and cross t of size 15x32mm made of 0.30 mm sheet, spaced between main t at 600mm c / c to form a grid of 600x600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixures, smoke detectors etc.main t runners to be suspended from ceiling using gi soffit cleats fixed to existing rafter, purlin, etc with dash fasteners, gi adjustable rods of 3mm dia with gavanised butterfly level clips, spaced at 1200 mm c / c along main t, bottom exposed width of 15mm of allt sections shall be centra black pre painted with polyester paint, and having a load bearing capacity of 12 kg / sqm, all complete at all height and dismantling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover filletscomplete all as specified and directed. 103 dismantling of asbestos cement ( corrugated, semicorrugated, etc. ) sheets in roof coverings complete all as specified and directed. 104 s&f pre painted galvatume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws fixed with l & j hooks and washers, in roofs, walls etc with grade of zink coating 275 complete all as specified and directed. 105 s&f pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified and directed 106 s&f 25mm dia fancy type stainless steel curtain rod fixed to bracket complete all as specified & directed. 107 s&f decorative type knob with bracket of stainless steel fixing at end of curtain rod complete all as specified & directed. 108 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from siteand making good disturbed surface of walls, floors etc. 109 disconnecting unserviceable sub main wiring / service connection of any size and including conduit of any type and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed. 110 taking downmcb dbs complete with mcbs / isolator etc removing materials from siteand making good disturbed surface of walls, floors etc complete all as specified and directed. 111 m&l for point wiring with 1.5 sqmm, pvc insulated, unsheathed, stranded copper conductor single core frls cable, is 694 marked, drawn through and including non metallic rigid pvc concealed conduit 20mm dia or higher complete with all pvc conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. / fittings isi marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 sqmm stranded copper conductor pvc insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for: 112 all as per item no. 111.00 here in before one light point / bell point controlled by one, one way switch. 113 all as per item no. 111.00 here in before one ceiling fan / exhaust fan point controlled by one, one way switch. 114 one three pin 5 amp socket on same board with other switches. 115 all as per item no. 111.00 here in before one 3 pin 5 amp socket on independent board. 116 all as per item no. 111.00 here in before one light point controlled by two nos two way switch. 117 all as per item no. 111.00 here in before but with 2.5 sqmm, for one 5 pin 5 / 15 amp socket on independent board including 2.5 sqmmstranded copper conductor ( frls ) pvc insulated green in colour as continous earth conductor connected to common earth. 118 s&f of sub main wiring with two runs of single core pvc insulated and unsheathed multistranded ( frls ) copperconductor cable of size 6.00 sqmm lt, 1100 volts grade, drawn through and including 25 mm dia or higher pvc nonmetallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistrandedcopper conductor cable green colour as earth continuity conductor complete all as specified and directed. 119 s&f switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed. 120 s&f switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed. 121 s&f switch piano flush type 5 amps, single pole two way 240 volts complete all as specified and directed. 122 s&f bell push piano flush type 5 amp complete all as specified and directed. 123 s&fsocket outlet 3 pin 5 / 6 ampflush type complete all as specified and directed. 124 s&fsocket out let 2 in 1, multipurpose 3 pin 15 / 16 amp flush type isi marked complete all as specified and directed. 125 s&f ceiling fan regulator electronic flush , steped ( four step ) 230 volts ac complete all as specified and directed. 126 s&f ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed. 127 s&f of door bell ding dong type electric 230 volts ac , single phase, complete all as specified and directed. 128 s&f of lamp holder pvc / polycarbonate type with back plate complete all as specified and directed. 129 s&f led tube light fitting in acrylic linear tube ( 1x 18 watt ) , 230v for single led tube lightincluding 1 x 18 w ledretrofitbar professional cw 6500 k cover channel, bipin holders, led power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. 130 s&f wall mounted decorative luminaire fitting suitalble for led lamp b 22 base 9 watt complete all as specified and directed by engr in charge. 131 s&f led lamp 10 watt suitable for 230 volts, 50 hz b 22 base complete all as specified and directed. 132 s&f led bulk head luminaire 1x 10 w bulk, ip 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed. 133 s&f testing and commissioning energy saving street light luminaire 35 watt led, pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete with individual led lences and complete all as specified and directed. 134 supply and fixing street light bracket made of 32 mm gi pipe, 1.2 mtr length fixed with two nos of clamp, nut and bolts complete all as specified and directed. 135 disconnecting and taking down existing electric meterand refixing the same electric meter, connecting, testing and sealing properly and making good disturbed surface of walls etc complete all as specified and directed. 136 taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan complete all as specified and directed. 137 s&f of mcb distribution board single pole & neutral with 200 amps rated bus bar, double door ip 42 dbs , made outof sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing mcbs complete all as specified and directed.note: mcb db and mcb sp / spn will be of same make. 138 s&f of mcb distribution board tpn 4 way, 415 volts, double door, with 200 amps rated bus bar, neutral bar with shrouds, earth bar, ip 43 , made outof sheet steel enclosure, recessed type, factory made powder coated suitable for housing mcbs as incomer andoutgoing complete all as specified and directed.note: mcb db and mcb sp / spn will be of same make. 139 s & f of mcb sp, 240 volt, 6 amp to 30 amp capacity, 10 ka, c curve complete all as specified and directed. 140 s & f of mcb spn, 240 volt, 32 amp capacity, 10 ka , c curve complete all as specified and directed. 141 s & f of mcb sp, 240 volt, 63 amp capacity, 10 ka , c curve complete all as specified and directed. 142 s&f of mcb tpn, 415 volt, 63 amp capacity, 10 ka, c curve complete all as specified and directed. 143 m&l for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore gi med grade with funnel and wire mesh pcc chamber in cement concrete 1:3:6 type c 2 and rcc cover with handle all as specified and shown in elect plate no 3 of ssr part i of 2009 including dismantling of old unsv existing earthing complete all as specified and directed. 144 supply and fixing storage type electric water heater ( geyser ) single phase 230 volts, stainless steel tank, vertical type oc capacity 25 ltr, bee 5 star rated connecting inlet / outlet / vent pipes, electric / earth connections , mounting bolts, nutsand carrying out testing for proper functioning including wiriting mes no with black enemel paint complete all as specified and directed. 145 supply and fix exhaust fan, steel body ac single phase, 230v of size 300 mm sweep with blades and frame and louvers suitable for 230 volts, single phase 50 hz ac supply, connecting with three core flexible copper cable including making hole for fixing of fan and making good the distrubed surface of wall complete all as specified and directed. 146 supply and fix ventilation fan, steel body ac single phase, 230v of size 250 mm sweep with blades and frame and louvers shutter suitable for 230 volts, single phase 50 hz ac supply, connecting with three core flexible copper cable including making hole for fixing of fan and making good the distrubed surface of wall complete all as specified and directed. 147 supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing xlpe insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 16 sqmm, 4 core complete all as specified and directed by engineer in charge. 148 supply and fixingtubes light grade gi tubing 40 mm dia withall fitting laid in trenches complete all as specified and directed. 149 excavation in trenched n exc 1.50 m in width and n exc 1.50m in depth for foundation , manholes , cesspits, laying cables cables, pipes etc n exc 10 sqm on plan and getting out in any type of soil complete all as specified and directed. 150 returning filling in including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed 151 removel of surplus soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above from the starting point complete all as specified and directed. 152 supply andlaying dry river sand for cable cushioning in trenches to required width at bottom and top cable including spreading, levelling, watering and consolidation, complete all as specified and directed by engineer in charge. note: punned thickness only shall be measured and paid. 153 m & l for old size sub class b’ bricks s as in cable cover, laid flat adjoining to each other width wise for protection of cables in trenches, complete, all as specified & directed. 154 taking down existing exhaust fan & wall mounted fan and re use at site or carrying to the store ( to be measured only when found serviceable in all respects complete forre use. ) complete all as specified and directed. 155 s&f led box type tube light fitting 20 watt made up of crca sheet with pre wired double sided connections including 1x20 watt retrofit led tube rod with extruded aluminium body , pc diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired complete all as specified and directed 156 s&f ceiling fan 1200 mm sweep , 230 volts, ac , 50 hz, copper winded motor, be star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and directed 157 supply, fixing and testing energy saving street light luminaire 25 watt led , pressure die cast housing with high power led as lighting source and lens embedded pc cover with ip 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by engr in charge. 158 s&f recess mounted 2 x 2led luminarie 36 watt, cool day / warm white light with white powder coated crca housing with led driver, efficiencey >100 lm / wcomplete all as specified and directed. 159 m&l for tv socket including pvc conduit and co axial wire complete all as specified and directed 160 m&l for telephone socket including pvc conduit and telephone wire complete all as specified and directed 161 s & f single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 amp mcb sp `c series for geyser complete all as specified and directed 162 total in figures 163 quoted amount in words...

Due Date : August 28, 2023

Tender Value : ₹ 48 Lakhs

View Tender
18
Department Of Defence - Rajasthan

38851081 bids are invited for misc items with sliding bolt, tower bolt and door stopper, size of angle iron 35 mm x 35 mm x 5 mm , door with ms angle frame size 750 mm x 1900 mm with 19 mm ply wood shutter complete with sliding bolt, tower bolt and door stopper, size of angle iron 35 mm x 35 mm x 5 mm , steel window size 1500 mm x 1200 mm with ms angle frame, double shutter 4 mm glass and wire mesh fitted, complete with tower bolt and window stopper , steel window size 1200 mm x 900 mm with ms angle frame, double shutter 4 mm glass and wire mesh fitted, complete with tower bolt and window stopper , steel ventilators, v 1 having size 600 mm x 300 mm , wc indian type , pvc cistern 10 ltrs cap , pvc pipe 110mm dia 6 mtr long , plastic jerricane 60 ltrs cap , plastic jerricane 35 ltrs cap , plastic jerricane 20 ltrs cap , plastic jerricane 10 ltrs cap , plastic jerricane 5 ltrs cap , steel jerricane 20trs cap , steel conical measuring can half ltr cap , steel conical measuring can 1 ltr cap , steel conical measuring can 2 ltr cap , steel conical measuring can 5 ltr cap , steel conical measuring can 10 ltr cap , rotary oil pump 12 mtrs head and max flow rate 250 ml in one rotation , plastic barrel pump model emk 12 , lever action barrel pump, cap 50 210 ltrs , steel funnel 05 ltrs cap , smart funnel with dust cap plastic 5 ltrs cap , drum wrench with high strength cast alluminium body, ideal for opening all types of drums total quantity : 26724...

Due Date : August 05, 2023

Tender Value : ₹ Ref. Documents

View Tender
19
Indian Army - Rajasthan

38841192 bids are invited for provision of misc maint stores 15mm dia , pvc connection 450mm long , cp pillar cock 15mm , m seal 200gm , flushing cistern , cp bib cock 15mm , sliding bolt 200mm long , tower bolt 150mm long , hydraulic door closure , window glass pane 1 feet x 1 feet x 4mm thick , window handle , steel window pegset , wiremess for door or window , acrylic sheet 2 feet x 3 feet , door handle , led tube light fitting 9 or 10w , led tube light fitting 18 or 20w , led bulb 10w , led bulb 12w , lt ug cable 10 sqmm 2 core , multistranded copper cable of size 1 point 5 sqmm , casing n capping 25mm , db spn double door 8 way , mcb spn 40a dp , pt switch 5a , piano type switch 15a , socket 5a , socket 15a , ss combination 5a with box , ss combination 15a with box , bulb holder , fan eloctroic regulator , flexible wire twin twisted , mcb 6 to 32 amps , ceiling rose , pvc switch board 6 feet x 8 feet , pvc switch board 8 feet x 10 feet , pvc insulation tap 25mm , led security light 25watt , bulk head fitting , mcb spn 32 amps , bty 12v and 75 ah for dg set total quantity : 741...

Due Date : August 17, 2023

Tender Value : ₹ Ref. Documents

View Tender
21
North Western Railway - Rajasthan

38369097 auction sale of abandoned 39 nos type i and 01 nos type iv quarters, released rr masonry=707.59 cum, released red stone slab=1265 sqm, released u / s ac sheet=30 sqm, released 50r rails=5406.68 kg, released wooden doors=1320 kg, released wooden windows=416 kg, released steel doors=1775 kg, released steel windows=456 kg, released cgi sheet=72 sqm, released girder =1231.1 kg, released steel jafferey=1595 kg...

Due Date : July 03, 2023

Tender Value : ₹ Ref. Documents

View Tender
22
Military Engineer Services - Rajasthan

38357851 repair /maint of wooden doors and windows,steel windows, cupboards and repair to approach path, hardstanding, drain cover etc in domastic area at air force station jaisalmer...

Due Date : July 19, 2023

Tender Value : ₹ 45 Lakhs

View Tender
23
North Western Railway - Rajasthan

38090828 auction sale of abandoned 35 nos quarters, released rr masonry=552.35 cum, released red stone slab=830 sqm, released u/s ac sheet=9 sqm, released 50r rails=4853.2 kg, released wooden doors=595.1 kg, released wooden windows=72 kg, released steel doors=945 kg, released steel windows=240 kg, released cgi sheet=45.2 sqm...

Due Date : June 16, 2023

Tender Value : ₹ Ref. Documents

View Tender
24
North Western Railway - Rajasthan

38090825 auction sale of abandoned 61 nos quarters, released rr masonry=803.13 cum, released red stone slab=1434.34 sqm, released u/s ac sheet=88.45 sqm, released 50r rails=14055.43 kg, released wooden doors=805 kg, released wooden windows=316 kg, released steel doors=1430 kg, released steel windows=240 kg...

Due Date : June 16, 2023

Tender Value : ₹ Ref. Documents

View Tender
25
North Western Railway - Rajasthan

38090814 auction sale of abandoned 38 nos type i quarters, released rr masonry=707.59 cum, released red stone slab=1265 sqm, released u/s ac sheet=30 sqm, released 50r rails=5406.68 kg, released wooden doors=1320 kg, released wooden windows=416 kg, released steel doors=1775 kg, released steel windows=456 kg, released cgi sheet=72 sqm, released girder =1231.1 kg, released steel jafferey=1595 kg...

Due Date : June 16, 2023

Tender Value : ₹ Ref. Documents

View Tender
26
Rajasthan Housing Board - Rajasthan

37991283 item 2 additional and alteration work of sewer and water pipe and steel window including repair work at rental houses jyoti nagar and jawahar nagar jaipur...

Due Date : June 12, 2023

Tender Value : ₹ 14.44 Lakhs

View Tender
27
Military Engineer Services - Rajasthan

37871050 repair /maint of wooden doors and windows,steel windows, cupboards and repair to approach path, hardstanding, drain cover etc in domastic area at air force station jaisalmer...

Due Date : June 24, 2023

Tender Value : ₹ 45 Lakhs

View Tender
28
Rajasthan Housing Board - Rajasthan

37863149 altration work of sewer and water pipe and steel window including repair work at rental houses jyoti nagar and jawahar nagar , jaipur. item 2...

Due Date : June 12, 2023

Tender Value : ₹ 14.44 Lakhs

View Tender
29
Military Engineer Services - Rajasthan

37255521 welcome maintenance for offrs qtrs under age b / r ii under ge ( n ) bikaner. 1 m&l preparingof old decorated surfaces of walland applying one coat of distemper oil emuision complete all as specified and as directed by engr in charge. 2 m&l preparingof old decorated surfaces of walland applying two coat of distemper oil emuision complete all as specified and as directed by engr in charge. 3 m&l preparing surfaces of plaster or unplaster old surface of wall and applying one coat of white wash complete all as specified and as directed by engr in charge. 4 m&l preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash complete all as specified and as directed by engr in charge. 5 m&l preparing surfaces of plaster or unplaster old surface of wall and applying one coat of white wash on ceiling complete all as specified and as directed by engr in charge. 6 m&l preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash on ceiling complete all as specified and as directed by engr in charge. 7 m&l preparing old surfaces of wall and applying one coats of plastic emulsion paint complete all as specified and as directed by engr in charge. 8 m&l preparingold surfaces of ceiingand applying one coats of plastic emulsion paint complete all as specified and as directed by engr in charge. 9 m&l preparing old surface of wood of any desc over 10cm width or girth and applying two coats of synthetic enamel paint .over pink primer complete all as specified and as directed by engr in charge. 10 m&l preparing new surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide complete all as specified and as directed by engr in charge. 11 m&l preparing the old painted wooden surfaces of any description over 10 cm width or girthand applying one coat of synthetic enamel paint.complete all as specified and as directed by engr in charge. 12 m&l preparing new surface of steel of any desc over 10cm width or girth and applying one coat of synthetic enamel paint over red oxide complete all as specified and as directed by engr in charge. 13 m&l complete removal of existing treatment and applying a thin layer of putty on wall surfaces complete all as specified and as directed by engr in charge. 14 m&l preparing new surface of old or new incl removal of old treatment ans applying a thin layerof plaster of paries to give a uniform finish as approved by engr in charge 15 m&l demolition of cement conc. in any description and incl any position not otherwise specially provided complete all as specified and directed 16 m&l dismanting floor, hearth or wall tiling including cement mortar bedding and removal of rubbish out of the premises complete all as specified and as directed by engr in charge. 17 hacking out old broken glass ( any thickness, size, quality or description ) fromwooden frame or stone concrete or brick surrounds glazed with putty or fixed with beads.complete all as specified and as directed by engr in charge. 18 dismantlingpipes of any desc fixed to wall or laid under floor complete all as specified and as directed by engr in charge. 19 dismantling cast iron pipes of any desc fixed to wall or laid under floor complete all as specified and as directed by engr in charge. 20 taking down cement plaster on brick or stone walls, including raking out joints, hacking for key, scrubbing down with water etc. 21 taking up or down steel tubing 15 mm diaand connections and stacking neatly for offering credit complete all as specified and as directed by engr in charge. 22 all as per item n 21 above, but 20 mm dia. complete all as specified and as directed by engr in charge. 23 taking down chowkhats or frameswith shutters ( without taking off shutters from the frames ) of size n. exc 1.5 sqm each complete all as specified and as directed by engineer in charge. 24 taking down chowkhats or frameswith shutters ( without taking off shutters from the frames ) of size exc 1.5 sqm but not exc 4.0 sqm each complete all as specified and as directed by engineer in charge. 25 taking down shutters of any description, areaexceeding 1.00 sqm and n.exc 2.00 sqm eachcomplete all as specified and as directed by engineer in charge. 26 m&l for welding in repairs n.exc 2.5 cm in length and not exceeding 6mm thick of metal complete all as specified and directed by engineer in charge. 27 s&f 1.25 mm thick pressed steel frames of size 125mm x 60mm for single doorsincluding necessary fixing lugs, hinges, lock strike plate, etc complete all as per is provns.complete all as specified and as directed by engr in charge. 28 s&f 1.25 mm thick pressed steel frames of size 105mm x 60mm for single doorsincluding necessary fixing lugs, hinges, lock strike plate, etc complete all as per is provns.complete all as specified and as directed by engr in charge. 29 s&f second classhard wood plain, framed, panelled shutters 35mm thick, ( any number of panels ) with panels of timber flat on both sides ( feather edged ) or of veneered partcile board medium density wood particle board with commercial faces venners supplied and fixed to chowkats.complete all as specified and as directed by engr in charge. 30 s&f second class hard wood, glazed and skelleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etcwithout sash bar, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc, size of members as directedsupplied and fitted to chowkats complete all as specified and as directed by engr in charge. 31 m&l for 25 mm thick flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces covered with decorative face veneer with lipping to matchcomplete all as specified and as directed by engineer in charge. 32 s&f solid pvc door frame of size 50 mm x 47 mm made out of 5 mm plain colour pvc sheet reinforced with m.s. square tube suppling & fixing in opening all as specified and as directd. 33 s&f factory made solidpanel pvc door shutter 30mm thick ( style ) consisting of framemade out of ms tubes for top and bttom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colourpvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail, panneling of plain color pvc sheetto be fitted in the ms frame welded / sealed to the stiles &rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site all as specfied and as directed. 34 s&f steel window / ventilators pressed steelframed ( box type ) factory made glaged and guaged with side hung shutters including pintolhinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded incl a prov of cooler / ac opening with shutter including one shop coat of red oxide primer complete all specified.note :i ) he window shall be fabricated as per drg no cebz / 888r & 889 sheet 1 to 4. ii ) ms fillets, glazing, wire gauge shall be measured and paid separately. 35 s&f framed work such as grills , framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to fe 410 0or fe 310 0 complete all as specified and as directed by engr in charge. 36 s&f stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples.complete all as specified and as directed by engr in charge. 37 s&f stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed in repairwith stainless steel wire staples.complete all as specified and as directed by engr in charge. 38 m&l for second classhard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints.complete all as specified and as directed by engr in charge. 39 m&l second classhard wood, in scantling wrought, in timber fixed complete all as specified and as directed by engr in charge. 40 teakwood beading 20x60mm half round complete supplied and fixed complete all as specified and as directed by engr in charge. 41 s&f 18 / 19 mmplywood, grade 1 ( with bwr resistant / termite proof ) with fixed with screws to timber frame work as in cup boards / cabinets etc complete all as specified and as directed by engr in charge. ( make : century / kitply / or other app by ge ) 42 m&l for water proofing block boards 18 / 19 mm , grade 2 exterior quality grade , commercial type fixed with screws to timber frame work. complete all as specified and as directed by engr in charge. 43 m&l for 0.9 mm thick decorative choice of laminates type i of surface finishwhitestuck with importedadhesive on sides of board as directed by eng in charge . ( make corby, or euro ) 44 m&l prelaminated partical board 19 / 20mm medium density , prelaminated with one side with decorative choicelaqmination and other side balancingwith white laminationfixed with screws as in shelves to kitchen almirah and cub board fixed in repair.complete all as specified and as directed by engr in charge. 45 s&f 12mm thick plywwod grade bwr , type bb , fixed with screws to timber frame work.complete all as specified and as directed by engr in charge. 46 s&f 6mm thick plywwod grade bwr , type bb , fixed with screws to timber frame work.complete all as specified and as directed by engr in charge. 47 m&l for 0.9 mm thick decorative choice of laminationtype 1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and as directed by engr in charge. 48 m&l for 1.50 mm thick pvc laminated decorative impressionchoice of laminationtype 1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions ( corby / duco ) . 49 s&f stain less steel catcherof superior quality complete all as specified and as directed by engr in charge. 50 s&f stain less steel pivoted type hingesof superior quality complete all as specified and as directed by engr in charge. 51 s&f 75mm long brass handle of desired finish with screws as approved by engg in charge. 52 s&f 35mm long mortice lockcomplete all as specified and as directed by engr in charge. ( make :godrej / harrison ) 53 s&f 75mm long brass tower bolt of desired finish with screws as approved by engg in charge. 54 s&f drawer side channel of std size and incl of rooler for moving drawer, mild steel bright finish, or electrogalavanised width of flap 30mm & length 60 mm all as specified. 55 s&f stainless steel fancy type, bright finish handles fixed with screw, of 125mm size all as specified. 56 s&f stainless steel multipurpose bracket in wooden / partitions for storing rations types made of 4mm dia stainless steel rods, fixed in side partition etccomplete.make: usha shriram enpt or equivalent ) . 57 s&f stainless steel luddel craddle hanging stand for cutlery all as specified and directed dy engr in charge.make: usha shriram enpt pvt ltd. 58 s&f stainless steelzero crank hinges fancy type ( with euro concealed hinges make: avis gold or equivalent ) fixed to shutter in cub board of std size and shape all asdirected dy engr in charge. 59 s&f 7s&f sinks made of stainless steel lmmthickkitchenorlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including fixing contilever brackets and connecting union to pipe complete all as specified and as directed by engr in charge. 60 m&l for recessed type stain less steelhandle for cup boards size 150 mm long complete all as specified and as directed by engr in charge. 61 m&l for roller ( pvc / stain less steel ) suiltable for sliding shutters . as app by eng in charge 62 pvc toilet cabinet with shelves and shutters fixed with looking mirror of size 600 x 450 mm complete all as specified and as directed by engr in charge. ( make : commander or equivalent ) 63 s&f continous ( piano ) hinges 30mm wide mild steel bright hinges 30 mm with flap, ms bright finished or electrogalvanised complete all as specified and as directed by engr in charge. 64 hasp and staple 100mm aluminium anodised, safety type, with mild steel hinges pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by engr in charge. 65 s&f mild steel peg set stay 300 mm with and incl screws and bolts complete all as specified and as directed by engr in charge. 66 butt hings, 100 mm long, extructed aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type c 21.complete all as specified and as directed by engr in charge. 67 s&f butt hings, 100 mm long, extructedisi marked complete all as specified and directed by engr in chargefixed complete all as specified and as directed by engr in charge. 68 s&f extruded aluminium alloy handles, 100 mm long, fabricated type anodised complete all as specified and as directed by engr in charge. 69 s&f aluminium, anodised , 100 mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed by engr in charge. 70 s&f extruded aluminium alloy handles, 150 mm long, fabricated type anodised complete all as specified and as directed by engr in charge. 71 s&f aluminium, anodised , 150 mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed by engr in charge. 72 supply and fix floor door stopper of aluminium alloy body, overall length of cover plate 140 mm and tongue anodised with hard drawn steel sring fixed in floor complete all as specified and as directed by engr in charge. 73 s&f aluminium alloy, anodised, slidding door bolt300mm long, with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed by engr in charge. 74 s&f mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete fixed in repair complete all as specified and as directed by engr in charge. 75 s&f figured glass, pin head type, 4mm thick and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed by engr in charge. 76 s&f 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not execeeding 0.5 sqm in each pane for metal frames complete all as specified. 77 s&f anodised aluminium with powder coating frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing etc. complete all as specified and as directed. 78 s&f anodised aluminium frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing etc. complete all as specified and as directed. 79 s&f sheet glass, ordinary quality 5.5 mm thick for aluminium door , window and vent.and glazing in square n exc 0.5 sq.m in each pane complete all as specified. 80 s&f neoprene / epdm rubber gasket for fixing sheet glass complete all as specified. 81 m & l pcc25 mm thick 1:2:4 type b0 ( 12.50 mm graded aggregate ) in any position in ground floor / roof complete all as specified and as directed by engr in charge. 82 m & l pcc75 mm thick 1:3:6 type b0 ( 12.50 mm graded aggregate ) in any position in ground floor / roof finishing cement concrete surface without using extra cement complete all as specified and as directed by engr in charge. 83 m & l pcc1:2:4 type b1 ( 20 mm graded aggregate ) as in hold fast blocks rungs etc icluding necessary form work complete all as per specified and directed ny engr in charge 84 m & l pcc 1:3:6 type c0 ( 12.50 mm graded aggregate ) as in filling in pressed steel frames complete all as specified and as directed by engr in charge. 85 m and l for coloured non skid ceramic tiles exceeding 0.11 sqm but not exceeding 0.18 sqm 7 to 8mm thick in floorsset and jointed in neat cement slurry and pointed incoloured cement to match the floorlaid over 15mm thick screed in cement mortar 1:6.complete all as specified and as directed by engr in charge. 86 m&l glazed ceremic tiles white450x300mmx7mm thickcoloured, set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floortiles as on vertical surfaces laid over 10mm thick cement screed in 1:4.complete all as specified and as directed by engr in charge. 87 m&l chequered cement concrete tiles 25 cm x 25 cmx25mm thick with grey cement and no pigment set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified 88 m&l for vitrified tiles not exceeding 0.36 sqm 10 mm thick in floors set and jointed in neat cement slurry and pointed in neat cement s;urry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified 89 m&l for vitrified tiles not exceeding 0.36 sqm 10 mm thick in floors set and jointed in neat cement slurry and pointed in neat cement s;urry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified but in vertical surface. 90 m and l for 20mm thick granitemachine cutslab table rubbed and polished graniteas on cooking platforms incl. pointing in white cement 1:2using marble dustwith admixture of pigmentto match with marble shadelaid over 20mm thick cement screed in cement mortar 1:6.complete all as specified and as directed by engr in charge. 91 rendering 10 mm thick in cm 1:6 on other than fair faces of brick work or concrete surfacesfinished fair and even complete all as specified and as directed by engr in charge. 92 rendering 15 mm thick in cm 1:4 on fair faces of brick work or concrete surfacesfinished fair and even complete all as specified and as directed by engr in charge. 93 rendering 5mm thick on fair faces ofconc. surfaces in cement mortar 1:3, even and smooth w / o using extra cement as on ceiling.complete all as specified and as directed by engr in charge. 94 s&f tubes, medium grade galvanised, 15 mm borewith all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed by engr in charge. 95 s&f tubes, medium grade galvanised, 20 mm borewith all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed by engr in charge. 96 s&f aluminium sheeting 0.56 mm thick alloy 31000 h4 in ridges, hips, valley gutter drip and straight flashing ( length and girth as fixed ) complete all as specified and as directed by engr in charge. 97 s&f mild steel work as in hold fasts, clamps, bands, straps etc conforming to fe 410 0 complete all as specified and as directed by engr in charge. 98 s&f sinks with drainage board made of stainless steel 1mm thick kitchen or laboutery with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm 330 mm x 160mm complete all as specified and as directed by engr in charge. 99 s&f stainless steel plate rack, tubular type, with fixing arrangement900mm x 900 mm size all as directed and as approved by engr in charge. 100 s & f glass corner of size 300mmx300mm with5.5 mm thick glass andsteelness steel clip and steelness steel railing allround the shelfcomplete all as specified and directed by engineer in charge . 101 s&f 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm th ac building board or commercial ply complete all as specified and as directed by engr in charge. 102 s&f 5mm thick looking mirror of selected quality with and including stainless steel spacers any size as approved by engrbevelled edge mirror of selected quality glass mounted on 6mm th ac building board or commercial ply complete all as specified and as directed by engr in charge. 103 s&f pvc ( swr ) pipes 75 mm bore, single socketed, in any length with rubber ring jointed fixed to walls complete all as specified and as directed by engr in charge. 104 s&f pvc ( swr ) pipes 110mm bore, single socketed, in any length with rubber ring jointed fixed to walls.complete all as specified and as directed by engr in charge. 105 s&f pvc ( swr ) branch piece, single ( single y ) equal or unequal, 75mmbore.complete all as specified and as directed by engr in charge. 106 s&f pvc ( swr ) vent cowl 75 mm complete all as specified and as directed by engr in charge. 107 s&f pvc ( swr ) floor trap 75 mm, plain with grating including jointing with solvent cement complete all as specified and as directed by engr in charge. 108 s&f pvc ( swr ) branch piece, single ( single y ) equal or unequal 110mmbore.complete all as specified and as directed by engr in charge. 109 s&f pvc ( swr ) bends any radius 75mm bore complete all as specified and as directed by engr in charge. 110 s&f pvc ( swr ) bends any radius 110mm bore complete all as specified and as directed by engr in charge. 111 s&f pvc ( swr ) gully trap 125 / 110 mm setting and jointing with solvent cement complete all as specified and as directed by engr in charge. 112 s&f in repair stack clamp out of 40mm x3mm flat iron stays with rubber gasket covering including bolt and nuts, spacer and securing ends of stays to walls or roof for 50mm bore piece complete all as specified and as directed by engr in charge. 113 s&f in repair stack clamp out of 40mm x3mm flat iron stays with rubber gasket covering including bolt and nuts, spacer and securing ends of stays to walls or roof for 100mm bore piece complete all as specified and as directed by engr in charge. 114 disconnecting existing tanks, setting aside ( or lowering if required ) for repairs cleaning etc andhoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirtetc from tanks and from mouths of circulating pipes etc complete ( capacity of tanksexc 250 ltr and n exc 500 ltrs ) complete all as specified and as directed by engr in charge. 115 s&f rotational moulded double layer ( isi marked of app make ) polythene water storage tank ( cylindrical vertical with closed top ) hoisted and fixed in position of 500 ltrs including dismantling existing.complete all as specified and as directed by engr in charge. 116 s&f ball valve high pressure of ptmt with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixedfixed in repair.of 20mm complete all as specified and as directed by engr in charge.make : prayag or equivalent. 117 s&f brass cp wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore.complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) . 118 s&f brass cp whb mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore complete all as specifie and as directed by engr in charge . ( make : parryware or hindware or equivalent ) . 119 s&f vitreous china wash down water closet pan with fixing bolts, trap ( pedestal pattern ) , white, ( excludingflushing cistern and flush pipe ) complete fixed in repairs complete all as specified and as directed by engr in charge. 120 supply and fix vitreous chinawash hand basin flat back size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand etc complete fixed in repairs complete all as specified and as directed by engr in charge. 121 s & f pvc valveless ( syphon internal fitting ) of pvc low levelaction type flushing cistern, 10 ltr capacity low level , whitewith inlet, ball valve, float and handle including brackets fixed in repairs complete all as specified and as directed by engr in charge. 122 s & f pvc valveless syphonic action type flushing cistern, 10 ltr capacity low level , whitewith inlet, ball valve, float and handle including brackets fixed in repairs.complete all as specified and as directed by engr in charge. 123 s&f pvc connections 15 mm size with ptmt nuts of length 450 mm complete all as specified and as directed by engr in charge. 124 s&f stainless steel tubular towel rail, 200 mm dia d type 60cm long between flanges complete all as specified and as directed by engr in charge. 125 s&f bib tap 15 mm dia, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwedfor iron pipeand fixed in repairs complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) 126 s&f bib tap 15 mm dia, long body fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwedfor iron pipeand fixed in repairs complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) 127 s&f stop valve, 15 mm dia, fancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and as directed by engr in charge. 128 s&f stop valve, 15 mm dia, concealed stop valvefancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and as directed by engr in charge. 129 s&f pillar taps, 15mm dia, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, long screwed shanks and fly nuts, screwed for iron pipe and fixed in repairs.complete all as specified and as directed by engr in charge.make: jaquar or equivalent 130 s&f brass chromium plated shower rose 125 mm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engr in charge.make: jaquar or equivalent 131 sf brass chromium plated shower arm 15 mm 195 mm long with bend 45 degreemm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engr in charge.make: jaquar or equivalent 132 s&f sheet glass shelf assembly in repair , oconsisting of 5.5 mm thick sheet glass shelf 12 cm wide chromium plated bracket guard and railing 60 cm long complete all as specified. 133 s&f plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by engr in charge. 134 s&f cp health faucetfixed type suitable for ewcs with 1, 5 mtr stainless steel tube complete all as specified and directed by engineer in charge make : jaquar, prayag 135 s&f cp toilet paper holder fancy type complete all as specified and directed by engineer in charge.make: jaquar or equivalent 136 s&f angle valve cast copper alloy fancy type cp with long shank and cup and screwed for iron pipefixed in repair complete all as specified and as directed by engr in charge.make: jaquar or equivalent 137 s&f waste pipe 32mm for whb with coupling fixed in repairs complete all as specified and as directed by engr in charge. 138 m&l for along the wall below concrete or masonry using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by engr in charge. 139 m&l for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and as directed by engr in charge. 140 s&f grating doom 125 mm dia with waste hole of ptmt ( minimum weight 40 gms ) complete all as specified and as directed by engr in charge. 141 s&f chromium plated soap dish complete all as specified and directed by engineer in charge. 142 s&f aluminium snake bead with bush duly fitted with screws with length equal to door width as specified and directed by engr in charge 143 m&l for repairingof rolling shutters making functional by providing greasing oiling , welding etc.including taking down rolling shutters or hood if required complete all as specified and as directed. 144 s&f safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed by engr in charge. 145 s&f ball bearing for rolling shutters.complete all as specified and as directed by engr in charge. 146 m&l for 25mm to 30mm thick plaster of paris ( pop ) ( gypsum anyhydrous ) raised moulding to flat surface of ceiling including preparation of surfaces all as directed.complete all as specified and as directed by engr in charge. 147 m&l for green sheet pvc of best quality to cover the surface where required complete all as specified and as directed. 148 s&f water closet pedestral pattern white or coloured ( as approved by engr in charge ) make :cera cat no.s1013113 ( cristy single piece suite p or s trap incl seat cover ) or equivalent in hindware , jaquar, parryware ) complete all as specified and as directed. 149 s&f in aluminium composite panel of any colour of having thickness of approx 3 4mm thick which are used in aluminium doors / partitions of all as specified and as directed. 150 s&f in pre laminated pvc boards of heat and fire resistant , non toxic , anti chemicaland corrosion resistant, termite proof and resistant to fungal attacks used in kitdhen cabinets of any finish complete all as specified and as directed. 151 m&l washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 ( 1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1:1 / 2:2 ( 1 cement: 1 / 2 coarse sand : 2 stone chipping 10mm nominal size ) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified ( paymentfor providing grooves shall be made separately ) . 152 s&f 10.00 mm thick gypsum boards as in ceiling as per approved desidg including recessing for provision of ceiling lights , moisture resistant , incl intermediate , perimeter channel ceiling channel , alon nuts and bolts connecting plates gypsum boards , dry wall screws soffits cleats , ceiling section, rowel plugs fixtures and screws complete all as spfd and as shown in sketch and applying twwo coats of emulsion paint over a coat primer on exposed surfaces.design of ceiling board as app by engr in charge. ( note: no extra payment shall be claimed from contractor for designs to ceiling falls etc ad shall be measured in plan only ) 153 m&l for 1.5mm thick self adhesive waterproofing membrane consisting of self adhesive sbs ( styrene butadiene styrene ) modified / bitumen compound covered on the top side with high density cross laminated polyethylene film and on the underside with an easy to peel silicon film all as per manufacturer’s instructions having minimum overlaps 50mm on sides and 100mm on ends, provided with & including suitable bitumen primer @ 0.30 litre per sqm as recommended by membrane manufacturer after cleaning the roof surface / sunken floor from all loose, dust, dirt, foreign material and particularly oil and grease marks, complete all as specified and as directed.make : m / s texsa india ltd / m / s pidilite industries ltd / m / s sika india pvt ltd / m / s stp limitednote : the net area of waterproofing treatment shall be measured and paid for without any extra allowance for side & end laps for membrane and this aspect shall be deemed included in the quoted rates. 154 taking down carefully ( aluminium ) point wiring complete of any type ( batten / surface conduit or concealed ) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper / white washing / colour washing to match with the existing surface complete all as spcified and directed. 155 taking down submain wiring aluminium / copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed. 156 taking down old u / s existingdb tpn 4 way anddb spn 12 way including mcb / mccb of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed. 157 m & l for point wiring with and including single core frlsh pvc insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of pvc concealed conduit with accessorieswithlaminated top cover fixed on ms sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmmfrlsh pvc insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by engr in charge for the following : ( a ) one light / fan / ex fan / bell / point controlled by one switch. 158 ( b ) one pin 5 amps socket point on the same board with other switches complete 159 ( c ) one 3 pin 5 amps socket on independent board. 160 ( d ) all as per item no 4 above but but one light point controlled by two 02 way switchboard complete and all as directed by engr in charge. 161 ditto all as per item no 157 above but with 4.0 sqmm copper wire for 3 pin socket outlet 20 amp on independent board complete and all as directed by engr in charge. 162 s&f switch piano type, 5 amp, single pole one way, 230 volts, flush type complete all as specified and as directed by engr in charge. 163 s&f switch piano flush type single pole, one way 15 / 20 amps 230 voltscomplete all as specified & directed by engr in charge. 164 m&l socket outlet 3 pin5 amps flush type230 voltscomplete all as specified and directed by engr in charge. 165 m&l for socket outlet 2 in 1, 3 pin, 5 & 15 amps, 230 volts t complete all as specified & directed by engr in charge. 166 s&f ceiling rose, surface backelite , three terminal ac, 230 voltcomplete all as specified. 167 supply and fixing led mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete.havells cat part no enduralinearneobs10wled865spcwh / wipro cat part no ll20 111 xxx 65ne3 / bclsb 10 wh 168 s&f led tube light fitting, 1x 20 22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24 / 0.20 sqmm complete all as specified and directed by engr in charge. make :philips bn021 led 20s psu cw gr s2 / crompton greaves lddr20 cdl dazzle ray / bajaj bclab 20w 169 s&f single pole and neutralenclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amp complete all as specified and as directed by engineer in charge. 170 supply and fixing fan regulator electronicsocket typefive step controlled 230v ac 50 hz forcomplete all as specified and directed by engr in charge. 171 s&f sheet metal enclosure mcb db, double door, tpn 4 way with 200 amps rated busbar all as specified and as directed. make: hegar / legrand / seimens 172 s & f double door, sheet metal enclosure, powder coated for mcb db spn 12 way fittedwith neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to is 13032 1991 complete all as specified and as directed by engr in charge. 173 s & f mcb sp, 5 32 amps , 240 volts, breaking capacity 10ka complete all as specified and as dircted by engr in charge. 174 s&f mcb 63amps, c curve tpn, 415 volts, complete all as specified and as directed by engr in charge. 175 supply and fixing bell push, flush type, 5 amp 230v ac 50 hz forcomplete all as specified and directed by engr in charge. 176 supply and fixing buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed by engr in charge. 177 m & l lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by engr in charge. 178 taking dowen and refixing led light fitting mirror type with high out put diffuser 2 feet, 10 / 5 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete. 179 taking dowen and refixingled tube light fitting, 1x 20 22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24 / 0.20 sqmm complete all as specified and directed by engr in charge. 180 s&f mccb 100 amps, 4 pole, 415 volts, fixed type breaking capacity 16ka complete all as specified and as directed by engr in charge. 181 s&f mccb 40 amps, 4 pole, 415 volts, fixed type breaking capacity 16ka complete all as specified and as directed by engr in charge. 182 s&f in replacement decorative wall light fittings complete made up of polycarbonate, including withfor 9 w led lamp complete all as specified and directed by engr in charge. make / sample approved by engr in charge : surya / havells / phillips 183 s&f in replacement bad side light fitting with suitable led bulb complete all as specified and directed by engr in charge. sample approved by engr in charge and ge . 184 s & f led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size. 185 s&f switch piano single pole 5 amps, two way, complete all as specified and as directed by engineer in charge 186 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300m 187 m & l for submain ( single phase ) wiring complete with and including 10 sqmm two single core, ( frlsh ) fire retardant, pvc insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, drawn through existing pvc conduitincluding accessories and fixed on walls and10sqmm, fire retardant, pvc insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by engr in charge. note : ( i ) two runs of10.0 sqmm pvc insulated wire and one run of 10sqmm wire and one run of pvc conduit shall be measured as one unit length. 188 m & l for submain ( single phase ) wiring complete with and including 4.0 sqmm two single core, ( frlsh ) fire retardant, pvc insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, drawn through pvc conduit of suitable size including accessories and fixed on walls and 4 sqmm, fire retardant, pvc insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by engr in charge. note : ( i ) two runs of 4.0 sqmm pvc insulated wire and one run of 4 sqmm wire and one run of pvc conduit shall be measured as one unit length. 189 s & f mcb spn, 5 32 amps, 240 volts, breaking capacity 16ka complete all as specified and as dircted by engr in charge. 190 m&l for submain wiringusing 4 runs of single core frls pvc insulated, unsheathed stranded copper conductor cable of size 4runs of 10 sqmm of voltage rating 1100v for three phase & neutral, drawn in and including concealed pvc conduit of dia not less than 25 mm dia with standard acessories, along with two run of frls pvc insulated, unsheathed, stranded copper conductor of size 2x6.0 sqmm as earth continuity conductor all as specified and directed ( note 4 runs of single core frls pvc cable 10sqmm for three phase & neutral with two run of earth conductor as earth and conduit shall be measured as one unit ) ...

Due Date : May 13, 2023

Tender Value : ₹ 45 Lakhs

View Tender
32
Military Engineer Services - Rajasthan

35865736 tender for repair and maintenance of misc b / r and e / m nature work in area under age ( i ) pokaran taking down carefully by unscrewing from boards / outlet boxes, switches, bell push, socket outlets, fan regulators, buzzers, holder and taken as schedule of credit. 2 disconnecting and removingthe mcbs, mccbs, dbs, metal clad switch from any height , stripping out the fitting for examine replacement of unserviceable spare parts, reassembling, refixing in original position includingminor repairs for the smooth functioning and testing complete all as specified & directed by engg in charge 3 m&l for attending, repair and rectification ofany type of internal elect supply complaint viz light point / fan point / 5 / 15 amps switch socket / submain wiring / mcbs / dbs / no electric supply on 230v / 415v system along with necessary t&p, safety devices, without replacement of items as per site requirement and as directed by engr in charge.note :1.the contractor shall detail / depute his supvr / electrician to receive the complaints from the concerned complaint cell and rectify the same on the given day alongwith necessary manpower and t & p as required.after completion of the complaints attended, the docket / slips shall be handed over to the concerned complaint cell.2. the cost of the stationery such as complaint register and docket book shall be deemed to be included in the rate quoted. 4 s & fswitch piano single pole flush type 5 amps, 230 volts. 5 s & fswitch piano single pole flush type 15 amps, 230 volts. 6 s & f single pole modular switch 1 way 6 amps, 1 module 7 s & fsingle pole modular switch 1 way 16 amps, 1 module 8 s&fbell push 5 a flush type 9 s&f modular bell push 6a, 1 module 10 supply and fixsocket outlet modular type multipurpose 2 / 3 pin, 6 amps, 230 volts combined 2 module 11 supply and fixsocket outlet modular type multipurpose 3 / 5 pin, 6 / 16 amps, 230 volts combined 2 module 12 supply and fixsocket outlet flush type multipurpose 2 in 1, 3 pin, 5 amps, 230 volts all as specified 13 supply and fixsocket outlet flush type multipurpose 2 in 1, 3 pin, 5 / 15 amps, 230 volts all as specified 14 s & fswitch socket combination flush type multipurpose 2 / 3 pin 5 amps 2 in 1230 volts all as specified. 15 s & fswitch socket combination 5 in 1 multipurpose 3 / 5 pin 5 / 15 amps flush typewith complete all as specified. 16 s & fmodular ceiling fan regulator stepped socket size ( modular ) suitable to work on 230 volts complete all as specified, 2 module 17 s & felectronic type regulator single module stepped heavy duty for ceiling fan suitable to work on 230 volts complete all as specified. 18 s & f electronic type regulator two module stepped heavy duty for ceiling fan suitable to work on 230 volts complete all as specified. 19 s&fbell ( buzzer / ding dong ) working on 230 volts ac supply 20 s & f lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings 21 s & fwall mounted 2 ft led batten of 9 watt with led lamp, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver complete including taking down all as specified and directed by engg in charge. make : havells cat part no luminebs9wled865spcwh / bajaj cat part no. bclsb10nw or equivalent. 22 s & f 4 ft box type tube light fitting with led tube rod of 18 / 22 watt , extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver complete including taking down all as specified and directed by engg in charge . make : havellscat part no regalbatten8upto1x22wssbswh and crystal1213t8dstl20wled865sglass / luker cat part no.llts1 or equivalent 23 supply and fix 4ft led tube rods of 18 / 20 / 22 watt complete including taking down all as specified and directed by engg in charge make: havells cat part no. crystal1213t8dstl20wled865sglass / bajaj cat part no.18wcdl orequivalent 24 s & f security lights of 1x25 watt led light with high power led and unique peanut lens to ensure uniform distribution and including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all including taking down as specified and directed by engg in charge.make : havells cat part no endura pearl sl25wled757sasytopcmp / luker cat part no lst24 or equivalent 25 m & l bracket made out of gi pipe of suitable dia not less than 1.2 mtr long and fixed on walls with 2 nos ms clamps made out of ms flat of suitable size thick complete with ms nuts, bolts and washers etc bent to required shape complete including taking down all as specified and directed by engr in charge 26 s & f 15 watt recess mounted circular downlight with white powder coated polycarbonate housing and pressure diacast , heat sink having high efficiency and including taking down all as specified and directed by engr in charge make : havells cat part no enduraneodlr15wled840mod and analogdrivernm12 / 15w / crompton cat part no.scr 15w cdl orequivalent 27 s & f 15 watt surface mounted circular downlight with white powder coated polycarbonate housing and pressure diacast , heat sink having high efficiency and all including taking down as specified and directed by engr in charge. make : havells cat part no enduraneohesurfacedls15wled840s / crompton cat part no. lcdspln r 12 ww or equivalent 28 s & f 24 watt recess softline luminaire ( 1x1 ) suitable for armstrong / grid ceiling with high brightnesswhite leds and pmma extruded diffuser giving glare free light and good aesthetic appeal and all including taking down as directed by engg in charge. make : havells cat part no pluto 1x1 plr15wled857s / crompton cat part no. ccr 141 24 57 sl nwh or equivalent 29 all as per sl item no 49. here in before, but 2x2 fittings of 45 wattsincluding taking down all as specified and directed by engr in charge. make : havells cat part no venus neo he 2x2plr42wled857mod , leddriver63v1a42ws / crompton cat part no.ccr 126 50 40 sl nwh or equivalent 30 s & f 10 watt bulk head luminaire suitable for outdoor with high brightness giving glare free light and including taking down all as directed by engg in charge. make :havels cat part no. hexaft10wled857ssymbopc / bajaj bibwp10wled or equivalent 31 s & f mcb sp 6 to 32 amps 240 volts for fixing on mcb dbsall as specified. 32 s & f mcb sp40 to 63 amps 240 volts for fixing on mcb dbsall as specified 33 s & f mcb spn 16 to 32 amps 240 volts for fixing on mcb dbsall as specified 34 s & f mcb spn 40 to 63 amps 240 volts for fixing on mcb dbsall as specified 35 mcb four pole, 415 volts suitable for fixing in mcb db of capacity63 amps including removing the existing us one and making good the distrubed surface to match with the existing surface. 36 mcb four pole, 415 volts suitable for fixing in mcb db of capacity100 amps including removing the existing us one and making good the distrubed surface to match with the existing surface. 37 s & f sheet metal enclosure mcb dbspn 4 way with 200 amps rated bus bar 240 volts double door with locking system complete all as specified 38 all as per sl item no 37 here in before, but spn 8 way db 39 all as per sl item no 37 here in before but spn 12 way db 40 s & f horizontal type tpn db 4 way double door made out of crca sheet housing duly powder coated & confirming to is specification complete all as directed by engr in charge. 41 s & f vertical loadline type tpn db 4 way double door with incoming as mccb tp 415 volts ac 3 phase50 hz with fixed magnetic setting for current rating of 100 amps 16 ka ( mccb tp confirming to is specification made out of crca sheet housing duly powder coated & confirming to is specification complete all as directed by engr in charge. 42 s & f single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amps ( ac box ) all as specified and directed 43 s&f mccbs 415v, 25ka, 100 amps 4 pole suitable for db including removing the existing unserviceable one and making good the distrubed surface to match with the existing surface. 44 all as per sl item no 43 here in before, but 63 amps, 10 ka 45 m & l submain wiring with 2 runs of single core 4 sqmm pvc insulated frls multistranded 1100 volts grade wire, copper conductor drawn through and including non metalic rigid pvc conduit and conduit accessories of medium grade not not less than 25mm dia including one run of single core 4 sqmm pvc insulatedsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from db to db / main board including removing the existing unserviceable submain riwing complete all as specified and as directed. 46 all as per sl item no 45, but 2 runs of single core 6 sqmm and one run of single core 6 sqmm as earth continuty conductornote :for sl item no 66 to 67: two runs of cable, one run of earth wire and one run of pvc conduit will be measured as one unit 47 supply and fix 36 watt cfl 4 pin typecomplete all as specified and directed by engg in charge. 48 supply and fix 18 watt cfl 2 pin typecomplete all as specified and directed by engg in charge. 49 supply and replace electronic driver fordownlight of any capacity / watt as per site required all as specified and directed by engineer in charge. 50 supply and replace electronic driver for led light of2x2 fittingof any capacity / watt as per site required all as specified and directed by engineer in charge. 51 supply and replace bi pin holdersuitable for 40 / 28 watts tubes ( pin & screw type ) 52 supply and replace cfl holdersuitable for 2 / 4 pin for 9 to 36 watts 40 / 28 watts tubes ( pin & screw type ) 53 supply and replace fan condenser 2.5 mfd 54 supply and replace fan condenser of 4.00 mfd 55 supply and replace split pins / lock pins for ceiling fans 56 supply and replace ms clamp with rubber bushes, bolts & nuts for ceiling fan along with lock pin all as specified 57 m & l for repairs to copper inner container like denting, soldering, brazing, leak testing and reassembling of any ltrs capacity water heater ( geyser ) complete all as specified. 58 supply and replace geyser element2000 watts of any type or as per site requirement 59 supply and replace thermostat 60 supply and replace indicator bulb 230 v suitable for any make and colour. 61 supply and replace pvc cold / hot water connection pipe 45 cms long 15 mm dia 62 m & l rewinding of burnt ceiling fan of1200 / 1400mm sweep motor with supper enameled copper wire of suitable size including repainting it white , replacement of sealed bearing and shaft of any make, type, model incl transportationcomplete all as specified and directed by engineer in charge. 63 m & l rewinding of burnt exhaust fan of 225 / 300mm sweep motor with supper enameled copper wire of suitable size including repaintingas per site requirement, replacement of sealed bearing and shaft of any make, type, model incl transportationcomplete all as specified and directed by engineer in charge. 64 s&f ceiling fan downrod of required heightincluding drilling of holes and threads for the same as per the site requirement all as direted by engineer in charge. 65 s & f ceiling rose three terminal surface bakelite type ac 50 hz 230 volts of size 65 x 50 mm complete all as specified. 66 supply and replace pvc round blocks 67 supply and replace pvc dummy sheets circular type of 4 68 supply and replace pvc dummy sheets circular type of 6 69 supply and replace rigid pvc casing & capping 20 / 25 mm wide 70 supply and replace pvc rectangular box ( gang box ) with 5 amps switch socket 71 supply and replace pvc rectangular box ( gang box ) with 5 / 15 amps switch socket 72 supply and replace pvc wire of flexible cord with copper conductor multistanded of twin core 23 / 0.198sqmm 73 supply and replace pvc insulated frls copper wire of size 1.5 sq mm multistranded 1100 volts grade 74 supply and replace pvc insulated frls copper wire of size 2.5 sq mm multistranded 1100 volts grade 75 supply and replace pvc insulated frls copper wire of size 4.0 sq mm multistranded 1100 volts grade 76 supply and replace pvc insulated frls copper wire of size 6.0 sq mm multistranded 1100 volts grade 77 supply and replace service wire twin core of 10.0 sq mm multistranded 1100 grade 78 supply and replace plug top 5 amps 3 pin 250 volts 79 supply and replace plug top 15 amps 3 pin 250 volts 80 supply and fix white hylam plain laminate sheet ofthickness as per the site requirement and as directed by engr in charge. 81 repair / maintenance of 25 ltrs ro plant of any make by removing of all electrical connections and water connections, rectification of all electric complaints including replacement of wiring and cleaning of all filters all as specified by engr in charge 82 s&f filters of 25 ltrs ro plant all as specified and directed 83 taking down chowkats or frames with shutters ( w / o taking of shutters from the frame ) exc. 1.5 sqm but n.exc. 4 sqm & removing from site. 84 taking down chowkats or frames with shutters ( w / o taking of shutters from the frame ) area n. exc 1.5 sqm removing from site 85 taking down shutter of any description and removing frome siteexc. 1 sqm & n. exc. 2 sqm each leaf. 86 taking down shutter of any description and removing frome siten exc. 1 sqmeach leaf. 87 m&l for joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. ( cut to ordinary lengths i.e. within 20mm of the length indicated ) fe 410 w ( gde e 250 ) quality a 88 s&f 35mm thick plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is: 1003 ( part i ) , kiln seasoned and chemically pressure treated 89 supply and fix flush shutter solid core construction with block board core and plywood face panels commercial typeboth side, 30mm thick. 90 s / f 2nd class h.w. skeleton shutter 35 mm thick open rebated & prepared to receive glass, gauze, etc. divided into squares with plain chamfered or rounded & rebated sash bars ( of any nos ) as spd in ssr pt i sec 8 cl. 8.20. ( a ) . 91 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s square tube, supplying & fixing in opening as per specification & drawing 92 s&f factory made solid panel pace door shutter 30mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails, m.s. frame shall be covered with heat moulded plain colour pvc `c channel heaving a pvc sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s frame wedded / sealed to the stiles, & rails with suitable pvc sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. 93 steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded 94 steel ventilator with top hung shutter including hinges, steel peg stay, complete 95 s&f 4 mm thick sheetglass ordinary quality and glazingwith oilputty in squaren exc 0.50 sqn in each pane. 96 s&f 4 mm thick figured glass, pin headed type and glazingwith oilputty in squaren exc 0.50 sqn in each pane. 97 resecuring or easing & adjusting, taking down shutters of any description n exc 1 sqm each refixing in same opening 98 resecuring or easing & adjusting, taking down shutters of any description exc 1 sqmn exc 2 sqm each, refixing in same opening 99 s&f 100 mm long mild steel but hinges medium weight cold rolled. 100 s&f in repairs 100 mm long mild steel but hinges medium weight colld rolld. 101 s&f 150 mm long aluminium anodised barrel tower bolt of extruded section. 102 s&f in repairs150 mm long aluminium anodised barrel tower bolt of extruded section . 103 supply and fix 150mm long extruded aluminium alloy handles, 150mm long fabricated type., anodised 104 supply and fix in repairs extruded aluminium alloy handles, 150mm long fabricated type., anodised 105 s&f 300 mm long aluminium alloy anodised sliding door bolt with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alu allow. 106 s&f in repairs 300 mm long aluminium allow anodised sliding door bolt with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alu allow. 107 s&f stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples 108 supply & fix in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples 109 supply and fix in repairs floor door stopper of aluminium body and tongue anodised with hard drawn steel spring fixed in floor over all length of cover plate 150mm. 110 supply and fix repairs decorative type curtain rod , stainless steel, 25 mm dia with not less than 1mm wall thickness complete all as specified and directed. 111 supply and fix decorative type brackets , stainless steel, suitable for above curtain rod complete all as specified and directed. 112 hacking out old broken glass ( any thickness, size, quality or description ) frommetal frame including punching or drilling out old glazing pins / spring clips and providing and fixing new ones 113 s&f 3 mm thick sheet glass ordinary quality & glazing with oil putty in squares n. exc. 0.5 sqm in each pane. 114 s&ffigured glass 3 mm thick, pin head type & glazing with oil putty in squares n. exc. 0.5 sqm in each pane 115 prelaminated particle board, interior grade, prelaminated both side 18 / 19 mm thick with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work but prelaminated both sides with decorative choice laminations 116 s&f continuous ( piano ) hinges, mild steel, bright finish or electro galvanizedwidth of flaps ( when open ) 30 mm. 117 m&l iind class hard wood plain fillets, square, rectangular or triangular in section, clean swan, se cured with nails or brads, sectional area not exc 3.00 sqcm. 118 s & f aluminium anodised hasp and staple 75mm , safety type, mild steel hinge pin including bolt to hinge plate and fixed with screws 119 s&f 100 mm long aluminium anodised barrel tower bolt of extruded section . 120 supply and fix extruded aluminium alloy handles, 100 mm long fabricated type., anodised 121 s&f, anodised aluminium frame & shutter for door, window and ventilator including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, hinges, tower bolt, etc complete all as specified & directed by engineer in charge. 122 supply only 5.5 mm thick sheet glass, selected quality, in square exc 0.5 sqm each pane including solar control film 25 micron reflective type over it. 123 supply only 5.5 mm thick sheet glass, selected quality, in square nexc 0.5 sqm each pane including solar control film 25 micron reflective type over it. 124 s&f door closer ( aluminium extuded body section ) hydreulically regulated, , designation no 1 universal type, suitable for door shutters up to 700mm in width and of wieght not more than 35kg complete all as directed. 125 s&fmild steel 4 lever mortice lock, vertical type of size 100mm all as directed. 126 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises 127 m&l for colored non skid ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colored cement to match, including 15 mm thick screed bed or bedded layer in cement mortar 1:6 for laying floor finish. 128 m&l for colored glazed ceramic tiles ( 300mm x450mm ) x 7 mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in white or colored cement to match including 10 mm thick plaster in cement mortar ( 1:4 ) on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing to receive / fixing dado / skirting tile. 129 dismantling of stone slab in any description or thickness, laid bedded jointed in any morter. 130 material and labour for granite ( of any type ) 18 to 20 mm thick work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match withshadeincl 15mm thick screed bed in cm 1:6 complete. 131 drilling holes for bolts, pipes, etc. n. exc 25mm dia in granite or trape stonefor gas connection pipe 132 rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations 133 s&f vitreous china coloured wash hand basin 580mm x 450mmfixed in repairs including 15 mm pillar cock cast copper alloy cp, 15mm cast copper stop valve, 32 mm brass cp waste fitting & 15 mm pvc connection pipe 450 mm long fixed in repairs 134 s&f vitreous china wash down water closet coloured pan ( pedestal pattern ) , white ( excluding fixing bolt, flushing cistern and flush pipe ) complete connected to drain fixed in repair 135 supply and fix in repairs vitreous china squatting pan, ‘orissa’ pattern, size 580 x 440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) 136 s&f in repairs plastic water closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device 137 s&f pvc flushing cistern 10 ltrs capacity isi marked incl pvc down take pipe and connection etc all complete in repairs. 138 supply and fix in repairs vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white ( minimum ) , with grating and union ( exclusive of fixing supply pipe to flushing cistern, trap and waste pipe ) fixed in repair 139 s&f for stop cock copper alloy cp screwed down high pressure with crutch or butterfly handle screwed both ends for iron / pipe or for union and fixed 15 mm bore in repairs 140 s&f bib taps cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs 141 s&f in repairs cp health faucet spray with 1.5m long pipe with wall hook& fixed in repair complete 142 supply and fix in repairs bib taps two way type , cast copper alloy with crutch or butterfly handle, sc rewed down, screwed for iron pipe or for brass ferrule 15 mm boreand fixed 143 s&f in repairs 32mm dia pvc waste pipeforkitchen sink , whb , urinal etc 144 supply and fix 15mm bore pillar taps of cast copper with capstan head cp screwed down high pressure with or without lettered hot and cold with long screwed shank and fly nut for iron pipe and fixed in repairs 145 s&f in repair brass cp mixer for mixing hot & cold water screwed down for iron pipe and fixed 146 s&f pvc connections 15 mm size with ptmt nuts to length 450 mm in repairs. 147 s&f , brass, chromium plated, tubular towel rail, 20mm dia, d type, 60cm long between flanges 148 s&f in repairs soap dish, any type, fixed to plugs with chromium plated brass screws 149 supply and fix in repairs brass chromium plated shower roses 125mm sizewith or without swivel joints, any size, including fixing to steel pipe or union 150 s / f s s grating dome of 100 mm dia ( min wt 25 gms ) to floor traps in repairs. 151 s & f 600mmx450mm beveled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers 152 taking down steel tubing and connections including cleaning for re fixing or removal to store of 15 mm bore 153 taking down steel tubing necessary fittings connection etc for 20 mm bore pipe 154 cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth 155 s&f gi tubes of medium grade with all fitting and fixed complete to walls and ceilings or laid in floors of 15 mm dia 156 s&f tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors 20 mm dia 157 supply and fix pvc ( swr ) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let 158 s&f in repair pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm dia 159 s&f in repair pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm dia 160 supply and fix in repairs ball valves high pressure of ptmt with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed in repairs of pipe 15 mm dia. 161 supply and fix in repairs ball valves high pressure of ptmt with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed in repairs of pipe 20 mm dia. 162 supply and fix in repairs 15 mm dia bib tap standard of ptmt any colour high pressure screwed for iron pipe and fixed . ( minimum weight 15mm 90gms / 20mm 125gms ) 163 supply and fix in repairs 15 mm dia pillar taps of ptmt any colour high pressure screwed for iron pipe and fixed ( minimum weight 15mm 110gms ) ) 164 supply and fix in repairs 15 mm dia stop valve of ptmt any colour high pressure screwed for iron pipe and fixed ( minimum weight 15mm 90gms / 20mm 112gms ) 165 s&f in repairs sinks made of stainless steel of 1 mm thick kitchen sink with plug washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 x 420 mm bowl size 410 mm x 330 mmx 160 mm 166 s&f in repair sinks made of stainless steel 1mm thick in kitchen sink with plug washers and waste pipe including bedding in cement mortar to dwaft wall or incl fixing cantilever brackets and connecting unionto pipe over all size 915 x 460 mm bowl size 410mm x 330 mm x 160mm all as specified and directed. 167 dismantling water tanks & removing from site, capacity of tanks exc 250 litres & n. exc. 500 litres capacity each 168 dismantling water tanks & removing from site, capacity of tanks 500 ltr and n exc 1000 ltr 169 s&f rotational moulded polyethelene water storage tanks ( cylindrical, vertical with closed top ) hoisted & fixed in position all as specified in ssr pt i, 500litre capacity. 170 s&f rotational moulded polyethelene water storage tanks ( cylindrical, vertical with closed top ) hoisted & fixed in position all as specified in ssr pt i, exc 1000 ltr capacity...

Due Date : February 11, 2023

Tender Value : ₹ 9 Lakhs

View Tender
34
Military Engineer Services - Rajasthan

35594842 tender for welcome maintenance at jalipa mil stn under ge army barmer taking down cement plaster of any description, on brick or stone walls etc.including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. ( note : work will be done / executed in patches without damaging other undamaged portion, of any size as directed ) 2 m&l for rendering 10mm thick plaster in cm ( 1:6 ) on faces of brick work or concrete surfaces, finished even and smooth ( without using extra lime or cement ) complete all as specified and directed. 3 m&l for rendering 5mm thick plaster in cm ( 1:3 ) on faces of brick work or concrete on surfaces of ceiling, finished even and smooth without using extra cement complete all as specified and directed. 4 m&l for rendering 15mm ( in two layers 10mm+5mm ) thick plaster in cm ( 1:4 ) on faces of brickwork or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 5 m&l for preparing new plastered or unplastered surfaces of walls and applying two coats of oil emulsion distempering over a coat of interior wall primer complete all as specified and directed. 6 m&l for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed. 7 m&l for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. 8 m&l for 3mm thick wall care putty on wall complete all as specified and directed. 9 m&l for preparation of new plastered surfaces of walls and applying two coat of cement based paint over a coat of primer complete all as specified and directed. 10 hacking out old broken glass ( any thickness, size, quality or description ) from from metal frame including punching or drilling out old glazing pins / spring clips, glazed with putty or fixed with beads and providing and fixing new ones complete all as specified and directed. 11 m&l for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and directed. 12 m&l for 3mm thick figured glass, pin head type and glazing with oil putty in squares in n exc 0.5 sq.m in each pane complete all as specified and directed. 13 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. 14 m&l for preparing old plastered or unplastered surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats of white wash complete all as specified and directed. 15 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed. 16 m&l for preparing old plastered or unplastered surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. 17 m&l for preparing old plastered or unplastered surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coat of white wash complete all as specified and directed. 18 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed. 19 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of oil bound distemper / emulsion complete all as specified and directed. 20 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats of oil bound distemper / emulsion complete all as specified and directed. 21 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails applying two coats of oil bound distemper / emulsionover a coat of interior wall primer over 3mm thick wall care putty complete all as specified and directed. 22 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of cement based paint complete all as specified and directed. 23 m&l for preparing old plastered or unplastered surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats cement based paint complete all as specified and directed. 24 m&l for preparation of old painted wood and wood based surfaces of any description over 10cm in girth or width and painting with one coat of synthetic enamel paint complete all as specified and directed. 25 m&l for preparation of old painted wood and wood based surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint complete all as specified and directed. 26 m&l for preparation of old painted steel or iron surfaces of any description over 10cm in girth or width and painting with one coat of synthetic enamel paintcomplete all as specified and directed. 27 m&l for preparation of old painted steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paintcomplete all as specified and directed. 28 demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed. 29 m&l for granite ( of any type ) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting andpolishing types including 15mm thick screed bed in cm ( 1:6 ) , complete all as specified and directed. 30 m&l for glazed ceramic tilesof size350mm x 250mm x 7mm / 450mm x 350mm x 7mm thick ( coloured ) of superior qualityfixed on vertical surfaces such asskirting / dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in cm ( 1:4 ) and pointed in coloured cement to match complete all as specified and directed. 31 m&l for non skidceramic tiles of size 7 to 8mm thick ( coloured ) ( square / rectangular ) area of each tile exc 0.06 but n exc 0.11 sqm, in floors, set & jointed in neatcement slurry and pointed in coloured cement over 15mm thick screed bed in cm ( 1:6 ) complete all as specified and directed. 32 taking up or down 15mm bore steel water tubing & connections from walls / ceilings / floors including cleaning for refixing or removal to store all as specified and directed. 33 taking up or down 20mm bore steel water tubing & connections from walls / ceilings / floors including cleaning for refixing or removal to store all as specified and directed. 34 s&f for 16mm bore of cpvc of food grade pipes sdr 11 and plain cpvc sdr 11 fittings on walls / ceiling or laying in floors complete all as specified and directed. 35 s&f for 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed. 36 cutting chases in brick walls, stone, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and directed. 37 s&f in repair 150 mm long aluminium anodizes barrel tower bolts of extruded section complete all as specified and directed. 38 s&f in repair 150mm size aluminium anodized handle complete all as specified and directed. 39 s&f in repair 250mm long aluminium alloy anodized sliding door bolts with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. 40 s&f in repair mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate and incl welding complete all as specified and directed. 41 s&f in repair 100mm size mortise lock, aluminium, vertical type, four leavers, all as specified and directed. 42 s&f in repair pvc cabinet 450x600mm overall size with looking mirror of selected qality 5mm thick glass mounted over pvc framing as per sample complete all as specified. ( make : neelkamal / prayag ) 43 s&f in repair 450mmx600mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 44 s&f for brass knobs 35 40mm dia complete all as specified and directed. 45 s&f ball catches with 8mm dia steel ball, and brass body and striking plate 140mm length including letting in and fixed complete all as specified and directed. 46 s&f in repair aluminium floor door stoppers double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified and directed. 47 dismantling of boarding any description fixed in any position with nails complete all as specified and directed. 48 m&l for prelaminated particle board of 18 / 19mm thick, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination with teak wood leaping on exterior face, fixed with screws as in cupboard shutters of bed room, kitchen andinternal shelves complete all as specified and directed. 49 s&f width of flaps ( when open ) in 40 mm continuous ( piano ) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. 50 s&f for 75mm size ms butt hinges cold rolled medium weight complete all as specified and directed. 51 s&f in repair stainless steel wire cloth 0.36mm nominal dia of wire andaverage width of aperture 1.40mm and fixed with stainless steel wire stapples of any type of windows and doors i.e. wooden, steel or aluminium including opening and refixing of frame, shutter or shutter elements if required and new wooden beads in wooden doors, complete all as specified and directed. 52 s&f in repair 20mm dia stainless steel curtain rod with fancy type fixing brackets, stops, rollers etc. complete all as specified and directed. 53 s&f in repairs mild steel window handles of approved quality with fixing nuts complete all as specified and directed. 54 s&f in repairs ms peg stay for steel window 300mm long with nuts complete all as specified and directed. 55 s&f in repair 15mm bore bib taps cp fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 56 s&f in repair 15mm bore dia pipe cp wall mixer for mixing ( hot / cold ) water, with wall cap / band of cp brass, screwed down, screwd foriron pipes 15mm bore complete all as specified and directed. 57 s&f in repair 15mm bore brass cp sink mixer fancy type with swinging casted spout ( wall mounted type ) for kitchen sink screwed down for iron pipe and fixed complete all as specified and directed. 58 s&f in repair 15mm bore centre hole basin mixer fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `hot and `cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed. 59 s&f in repair 15mm bore cp fancy type stop valves / angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and directed. 60 s&f in repair 15mm bore two way bib taps ( for health faucet / jet spray ) fancy type, chromium plated, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 61 s&f in repair 32mm dia pvc waste pipe for whb / sink complete all as specified and directed. 62 s&f in repair 15mm bore, 450mm long, pvc connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and directed. 63 s&f in repair vitreous china wash down water closet pan ( pedestal pattern ) , white including p or s trap, connection to drain ( or outgoing pipe ) and to flushing pipe with and including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device complete all as specified and directed. 64 s&f in rep vitreous china squatting pan “orissa” pattern, of size 580mm x 440mm white with integral foot rests and trap ( excluding flushing cistern and flush pipe ) including trap and provn of cement concrete bedding complete as fixed complete all as specified and directed. 65 s&f in repairs wash hand basins, vitreous china, of size 550x400mm ( flat back, or angle back type ) including cutting for and pinning in ends of brackets or erecting standinclusive of fixing of supply and waste pipe etc complete all as specified and directed. 66 s&f in repair plastic water closet seat for pedestal / semi pedestal closet pan, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. 67 s&f in repair pvc valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and directed. 68 s&f in repair brass chromium plated shower rose 125mm size complete all as specified and directed. 69 s&f in repair health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect complete all as specified and directed. 70 s&f in repair ss soap dish, approximate size 150x 150x80mm, fixed to plugs with chromium plated brass screws complete all as specified and directed. 71 s&f in repair toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated ( cp ) brass screws complete all as specified and directed. 72 s&f in repair sheet glass corner wall mounted shelf assembly consisting of 8mm thick sheet glass 220mmx220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and directed. 73 s&f in repair brass chromium plated tubular towel rail 20mm dia, d type, 60cm long between flanges complete all as specified and directed. 74 s&f in repair jet spray ( abs body ) mild steel chromium plated suitable for 15mm dia pipe with 1.00 metre long flexible tube including making connections and fixed in position complete in all respect complete all as specified and directed. 75 s&faluminium window / ventilator frame with side hung shutters ( fully glazed ) and aluminium grill 7.50mm thick as per design code no. 007 of dural grill or equivalent make as approved comprising of chokhat and shutters weight not less than 0.55kg / rm including jointing cleat, aluminium snap beading 20x15mm, rubber gasket, glazing clip, sheet glass 3.00mm thick selected quality for panels and aluminium hardware fitting fixed with steel chromium plated screws such as 02nos, 100mm size aluminium d type handles, 02 nos 75mm size stainless steel medium weight hinges, 02nos 100mm long aluminium tower bolts, one peg stay 150 mm long etc including taking down complete all as specified and directed . 76 s&f powder coated aluminium door frame with side hung shutters ( fully glazed ) comprising of chokhats section 101.04 x 44.45 x 1.5mm thick, shutter top rail 86.17 x 44.45 x 2.3mm, bottom and lock rail 150 x 44.45 x 2.3mm and style 53.7 x 44.45 x 2.3mm and including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip, sheet glass 5.5mm thick figured / solar control film glass selected quality for panels and aluminium hardware fitting fixed with steel chromium plated screws such as 02 nos disc type round handles, 03 nos 100mm size hinges, 03 nos 150mm long tower bolts, one floor door stopper with hard drawn steel spring 140mm long, 01 number of double action floor spring hydraulically regulated made upto minimum 1.25mm thick aluminium alloy sheet junction box for each leaf main body with stainless steel sheet cover governing pivot of brass, other parts made of mild steel heavy duty etcincluding taking down complete complete all as specified and directed. 77 s&f aluminium door frame with side hung shutters ( fully glazed ) comprising of chokhats section 101.04 x 44.45 x 1.5mm thick, shutter top rail 86.17 x 44.45 x 2.3mm, bottom and lock rail 150 x 44.45 x 2.3mm and style 53.7 x 44.45 x 2.3mm and including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip, sheet glass 5.5mm thick figured / solar control film glass selected quality for panels and aluminium hardware fitting fixed with steel chromium plated screws such as 02 nos disc type round handles, 03 nos 100mm size hinges, 03 nos 150mm long tower bolts, one floor door stopper with hard drawn steel spring 140mm long, 01 number of double action floor spring hydraulically regulated made upto minimum 1.25mm thick aluminium alloy sheet junction box for each leaf main body with stainless steel sheet cover governing pivot of brass, other parts made of mild steel heavy duty etc including taking down complete all as specified and directed. 78 m&l for prepration of surface by cleaning to remove loose particles, dust, latance etc, cutting grooves again remove loose particles, dust, latance etc properly, filling cracks / damaged portions / hollow areas / gaps of rcc and masonary upto 10mm to 15mm widhth and 10mm to 20mm deep by using polymer modified cement mortars and making good surface like existing painted surface with the help of cement mortar and paint all directed and as per manufacturers instructions. make : m / s asian paint / berger / m / s pidilite industries ltd / stp ltd / choksey. 79 m&l for prepration of preparation of new / old decorated plastered or unplastered surfaces of walls / chajjas by cleaning to remove loose particles, dust, latance etc., filling of holes / cracks with cns filler material. applying one priming coat ofsmart care damp proof with thinner at the rate of 0.40 ltr / sqm ( 0.20ltr smart damp proof : 0.20ltr water ) . applying second coat ofsmart care damp proof after 05 to 06 hrs at the rate of 0.40 ltr / sqm, and apply the third coat after 6 to 8 hrs once the second coat is dry at the rate of 0.40 ltr / sqm all directed and as per manufacturers instructions. make : m / s asian paint / berger / pidilite industries ltd / stp ltd. / choksey. note : cracks filler, priming coat and damp proofing coat shall be used of same make / manufacturer. 80 taking down copper / aluminium point wiring ( light, fan, socket or power ) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing unserviceable materials for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls, floors etc complete all as specified and directed. 81 taking down unserviceable main switch / db, teak wood boards etc complete all as specified and directed 82 taking down old unserviceable sub main wiring and making good the disturbed surfaces complete all as specified and directed. 83 m&l for point wiring surface type with single core 1.5 sqmm pvc insulated unsheathed single core multistranded copper conductor cable ( frls ) including 1.5 sqmm pvc insulated unsheathedcopper conductor as earth continuity conductor drawn in and including isi marked pvc casing caping not less than 20mm width with its accessories, including necessary modular metal flush box / pressed steelterminal boxes and modular white cover plate / 3 mm thick isi marked laminated sheet cover and ss screws with cup washers for fixing switches, sockets, fan regulators etc. including making good disturbed surfaces if any with cement mortar 1:3 for fixing switches / sockets / regulators etc. for one light point controlled by one switch complete all as specified and directed. 84 all as per srl item no 83 above but for call bell point controlled by one switch. 85 all as per srl item no 83 above but for one light point controlled by two 2 way switches. 86 all as per srl item no 83 above but for one fan point controlled by one switch. 87 all as per srl item no 83 above but for one 3 pin 5 amps socket outlet point on independent board. 88 all as per srl item no 83 above but for one 3 pin 5 amps socket point on the same board with other switches. 89 all as per srl item no 83 above but with cable 2.5 sqmm including 2.5 sqmm cable as earth wire for 15 / 16 amp socket. 90 all as per srl item no 83 above but with cable 4 sqmm including 4 sqmm cable as earth wire for 15 / 16 amp socket. 91 m & l switch piano, flush type single pole, one way 5 amps complete all as specified and directed. 92 m&l socket outlet 2in1, 3pin, 5a complete all as specified and directed. 93 m&l switch socket combination 2 in 1, 3 pin, 5 amps and 15 amps flush type universal complete all as specified and directed. 94 m&l ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed. 95 supply and fix steped type electronic fan regulator flush type, 230 volt, ac complete all as specified and directed. 96 m&l bell push, flush type, 5 amps complete all as specified and directed. 97 m&l call bell ac, 230 volts single pole complete all as specified and directed. 98 supply and fixing 06 to 32 a rating 240v, 10 ka c curve miniature circuit breaker ( mcb ) of single pole and current carrying capacity in the mcb db complete with connection testing and commissioning complete all as specified and directed. 99 all as per srl item no 98 above but spn 6 32 amps. 100 supply and fixing 415v 10ka c curve miniature circuit breaker ( mcb ) of tripple pole and neutral ( tpn ) and current carrying capacity 40 to 100 a in the db complete with connection testing and commissioning complete all as specified and directed. 101 supply and fix single pole and neutral enclosures with a two pin and earth plug and socket complete with one double pole mcb 20 a, 240 v complete all as specified and directed. 102 s&f mcb, db double door type, made out of crca mild steel sheet flushed in wall, spn 8 way , 240 volts ip 43, with pvc mcb blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of mcbs and isolators etc including complete all as specified and directed. 103 s&f mcb, db double door type, made out of crca mild steel sheet flushed in wall, tpn 4 way with 200 amps rated bus bar , 415 volts ip 43, withpvc mcb blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of mcbs and isolators etc includingcomplete all as specified and directed. 104 m&l sub main wiring surface type with two runs of single core, pvc insulated, unsheathed multi standard copper conductor cable of size 4 sqmm, 1100 volts grade ( frls ) and one run of 4 sqmm pvc insulated multi stranded copper conductor for earth continuityconductor drawn through and including suitable size isi marked rigid pvc conduit with all necessary accessories such as bends, tees, junction boxes, elbowscomplete all as specified and directed. ( note : two runs of 4 sqmm cable, one run of 4 sqmm continuity earth wire and one run of pvc conduit with all necessary accessories will be measured as one length ) . 105 m&l sub main wiring surface type with two runs of single core, pvc insulated, unsheathed multi standard copper conductor cable of size 6 sqmm, 1100 volts grade ( frls ) and one run of 6 sqmm pvc insulated multi stranded copper conductor for earth continuityconductor drawn through and including suitable size isi marked rigid pvc conduit with all necessary accessories such as bends, tees, junction boxes, elbowscomplete all as specified and directed. ( note : two runs of 6 sqmm cable, one run of 6 sqmm continuity earth wire and one run of pvc conduit with all necessary accessories will be measured as one length ) . 106 supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep, min air delivery 210 cfm with service value 6.00 bee. five star rated with brushless direct current motor ( bldc ) complete including connecting with 3 core flexible copper conductor including taking down the existing ceiling fan and depositing the same in mes store complete all as specified and directed. 107 supply and fix ceiling fans, complete with three blade, down rod, accessories 230v, 1200mm sweep, with squirrel cage induction motorcomplete including connecting with 3 core flexible copper conductor including taking down the existing ceiling fan and depositing the same in mes store complete all as specified and directed. 108 supply and fix exhaust fan, steel body ac single phase. 230v of size 300m sweep with, blades, and frame and louvers complete including connecting with 3 core flexible copper conductor including taking down the existing exhaust fan and depositing the same in mes store complete all as specified and directed. 109 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 250mm complete including connecting with 3 core flexible copper conductor including taking down the existing exhaust fan and depositing the same in mes store complete all as specified and directed. 110 supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 kw capacity 25 litre, bee 5 star rated complete with all accessories such as safety valve, thermostate, nrv, connection piece etc. and fixing on wall with toggle bolts and connecting with pvc flexible pipe complete including taking down the existing storage water heater and depositing the same in mes store complete all as specified and directed. note: pvc connection pipe, ground toggle bolts for fixing water heater will be measured and paid separately under relevant items. 111 supply only ground toggle bolts ( tower / anchor ) , 6 long along with washers and nuts for fixing geysers 25 / 50 ltrs capacity. 112 supply only pvc connection 15 mm bore with ptmt nuts of length 600mm in repairs complete all as specified and directed. 113 supply only pvc metal braided connection pipes for hot water supply with brass adopters 600mm long. 114 supply and fix in repair led bldg security light fitting 25 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection complete all as specified and directed. 115 supply and fix in repair led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed 116 supply and fix in repair led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 117 s & f in repair led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 118 supply and fix in repair lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. 119 taking out old u / s rubber reel of ceiling fan any make / size and supply and fixing heavy duty shackle type rubber reel complete with clamps. nut, bolt with split pin and washers complete all as specified and directed. 120 taking out defective capacitor and supply and fixing capacitor of rating 2.5 / 3.15 mfd230 vall as specified and directed. 121 supply & fix in repair fan regulator electronic step type 300 watt 240 volts including dismantling of old unserviceable regulator complete all as specified and directed. 122 supply and fix in repair modular switch 1 way 6 a, 1 module complete all as specified and directed. 123 supply and fixin repair modular switch 1 way 16 a, 1 module complete all as specified and directed. 124 supply and fixin repair modular bell push 6 a, 1 module complete all as specified and directed. 125 supply and fix in repairmodular socket, 6 a 2 / 3 pin combined 2 module complete all as specified and directed. 126 supply and fixin repair modular socket, 6a / 16a 2 / 3 pin combined 2 module complete all as specified and directed. 127 supply and fix in repair switch piano, flush type single pole, one way 5 amps complete all as specified and directed 128 supply and fix in repair switch socket outlet 2in1, 3pin, 5a complete all as specified and directed 129 supply and fixin repair switch socket combination 2 in 1, 3 pin, 5 amps and 15 amps flush type universal complete all as specified and directed 130 supply and fix in repair bell push, flush type, 5 amps complete all as specified and directed. 131 supply and fixin repair call bell ac, 230 volts single pole complete all as specified and directed 132 s&f in repair pvc board 30 x 25 x 5 cm depth medium quality isi marked complete all directed. for fixing of switches, sockets and regulators including taking down the old one complete all as specified and directed. 133 m & l for inverter point wiring forlight, ceiling fan and 5 amp socket with 2.5 sqmm, pvc insulated, unsheathed, single core multistandard copper conductor cable ( frls ) , 1100 volts grade including 2.5 sqmm pvc insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including pvc conduit medium grade isi markedwith its acessories upto the main dband 15 a switch socket combination with gang box flushed in wallfor inverter power supply complete all as specified and directed....

Due Date : February 01, 2023

Tender Value : ₹ 22 Lakhs

View Tender
35
Indian Army - Rajasthan

34743271 bids are invited for supply of hardware and certain other items marked , mcb, series c, operating voltage 240 v 415 v ac, 60 v dc per pole, spn, rating 32 amps, isi marked , mcb, series c, operating voltage 240 v 415 v ac, 60 v dc per pole, tpn, rating 63 amps, isi marked , mccb , ac 415 v breaking capacity 25 ka , four pole ,current rating 160 amp, isi marked , mccb , ac 415 v breaking capacity 25 ka , four pole ,current rating 100 amp, isi marked , mccb , ac 415 v breaking capacity 35 ka , four pole ,current rating 400 amp, isi marked , gi socket 25mm isi marked , gi tee 40mm isi marked , gi socket 50mm isi marked , gi reducer socket 50x15mm isi marked , gi reducer socket 25x20mm isi marked , gi reducer elbow 25x20mm isi marked , gi reducer elbow 25x15mm isi marked , gi elbow 25mm isi marked , gi elbow 50mm isi marked , gi elbow 40mm isi marked , gi union 25mm isi marked , door handle alum 125 mm long, isi mark , door handle alum 150mm long, isi mark , door stopper aluminium, isi mark , tower bolts alum 150mm, isi mark , m s bow handle 125mm, isi mark , m s steel window handle 100mm, left , m s steel window handle 100mm ,right , m s tower bolt 200 mm, isi mark , m s tower bolts 250mm, isi mark , m s tower bolts 125mm, isi mark , ms helical door spring hinges best quality , m s window stay 300 mm long, isi mark , m seal in100 gram pack , white cement in 1 kgs packing , washer set for low level flushing cistern , pvc washer for bib cock 15mm , stainless steel screw full thread 35 x 8 , stainless steel screw full thread 20 x 6 , stainless steel screw full thread 60 x 10 , stainless steel screw full thread 45 x 8 , gypsum screw full thread 35 x 8 , gypsum screw full thread 38 x 8 , gypsum screw full thread 32 x 8 , gypsum screw full 2 / 45thread 50 x 8 , stainless steel hinges size 4 inch , stainless total quantity : 6774...

Due Date : November 17, 2022

Tender Value : ₹ Ref. Documents

View Tender
36
Rajasthan Housing Board - Rajasthan

34503023 item 2 providing and fixing of aluminum window providing and fixing of aluminum window in place of steel window at head office building jaipur...

Due Date : October 31, 2022

Tender Value : ₹ 11.13 Lakhs

View Tender
38
Medical And Health Services - Rajasthan

34206683 construction of shc bejpur block itawa distt. kota 1 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 mtr. all kinds of soil 3 filling in plinth with locally available river shingle under floors including watering ramming consolidating and dressing complete including cost of shingle sand. 4 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 5 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 6 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.m20 grade nominal 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 8 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for :columns, pillars, posts and struts etc. 9 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 10 random rubble stone masonry for foundation and plinth in cement sand mortar above 30 cm thick wall in :cement mortar 1 : 6 (1 cement : 6 sand). 11 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 12 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. thermo mechanically treated bars (conforming of relevent is code) 13 filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 mtr. and lift upto 1.5 mtr. 14 filling in plinth withlocally available good earth under floors including watering ramming consolidating and dressing complete including cost of locally available good earth 15 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in :cement mortar 1 : 6 (1 cement : 6 coarse sand) 16 half flyash brick masonry in superstructure , above plinth level upto floor three levelusing flyash bricks of designation 75 cement mortar 1 : 6 (1 cement : 6 coarse sand 17 random rubble dry stone kharanja under floor. 18 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of :green / black / other granite. above 3601 cm2 slabs 19 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 20 providing and fixing 1st quality mat finished ceremic tile size 300 x 300 mm confirming to is : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (untile of roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of the complete (including the cost of cement mortor bed1:4). category a : kajaria, jhonson, somani make 21 providing & fixing vitrified paving tiles size 600 mm × 600 mm × 12 mm thick fix with cement mortar over 20 mm thich (1 cement 4 sand) laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (untile or roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortor 1:4) category a : kajaria, jhonson, somani make 22 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure a :30 mm thick commercial veneer both side 23 add extra in flush doors :for double leaf 24 for external teak wood lipping on flush door30mmx6mm 25 extra for cutting rebate in flush door shutters (total area of the shutter to be measured). 26 providing and fixing anodised aluminium curtain rod with aluminium brackets complete :25 mm dia 27 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded with 15 x 3 mm lugs, 10cm long embedded in cement concrete blocks 15 x 10 x 10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 28 supply and fixing in cement mortar welded hand railing made out of ms round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or pvc hand railing to be paid extra) with priming coat of red oxide. 29 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 30 providing and fixing m.s. sheet single leaf door shutter in angle iron frame 35 x 35 x 5 mm suitabilly diagonally braced with 25 x 3 mm flat iron above and below lock rail of size 50 x 5 mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats : including two coats of anit corrasite red oxide primer paint. m.s. sheet 18 s.w.g. 31 supplying and fixing of steel windows made out (65 x 40 mm) hollow metal pressed section of 1.25 mm thick sheet f4 & f7 standard rolled section conforming to is 1038 with wholly openable shutter of 0.80 mm thick (out side & inside) opening c.r. sheet embossed panels, joints matted and flush welded with suitable hinges, steel lugs & screws with approved oxidised steel handles, fittings, peg stays (casement stays) etc. complete in all respect including providing 10 mm square m.s. bars 10 cm. c/c and applying priming coat of red oxide paint. 32 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance. 33 providing batta (gola) 75 mm x 75 mm in cement concrete (1 : 2 : 4) including finishing with cement mortar 1 : 3 as per standard design. 34 providing & laying chequerred plain cement concrete embossed to specially manufactured non slipping tiles of approved make 20 mm thick laid on 20 mm thick bed of cement mortar 1 : 6 jointed with neat cement slurry complete.medium shade using approximately 50% white cement and 50% ordinary cement. 35 plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :25 mm thick 36 plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :20 mm thick 37 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand). 38 applying priming coat :with ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. 39 painting with enamel paint of approved brand and manufacture to give an even shade :two or more coats on new work. 40 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including prepration of base and all scaffolding :new work (two or more coats) over and including scrapping and priming coat with cement primer. 41 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. new work 42 renewing glass panes, with putty and nails wherever necessary :4 mm thick plain glass panes. 43 supplying and fixing dressed sand or other approved stone shelves, tands in cement mortar 1 : 3 with fine dressed edges : 35 mm thick. 44 supplying and fixing in walls machine cut and polished stone shelves, tands andin cm 1:3 with machine cut edges :kota stone 25 to 30mm thick. 45 making of health wellness center patern (gola) including colour picture work in side for fascasde branding includig material labour and t & p as pe direction engineer in charge as per standared drawing/patern 46 making of border of window health wellness center as per given patern for fascasde branding includig material labour and t & p as pe direction engineer in charge up to window size 4x5.6 as per standared drawing/patern 47 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge.granite work / kota stonefull edge moulding 48 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completebirla/j.k./nerolac or iso. as per direction of engineer in charge. 49 providing& fixing precast cement concrete coping 1: 2:4mix50mmthickcompleteas per specification 50 finishing with 25 mm thick cement plaster on roofs in cement sand mortar 1 : 4 mix including water proofing compound @ 2% of cement used. with neat cement, finishing, curing etc. complete in all respect including making of 300 mm x 300 mm square. 51 providing and fixing indian type white glazed vitreous china 1st quality w.c. orissa pan (is : 2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor. size 580 x 440 mm 52 p & f wvc wash basin (1st quality is : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p.pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall. size 510 mmx 400 mm 53 p & f wvc wash basin (1st quality is : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p.pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall. size 550 x 400 mm dia for counter top 54 p & f kitchen & lab sink of approved make with c.i. brackets duly painted, 40 mm c.p. waste coupling, c.p. brass chain with rubber plug, 40 mm g.i. waste pipe upto floor level complete including cutting & making good the wall & floor. 1.0 mm thick salem stainless steel aisi 304 kitchen sink of approved make (nirali, neel kanth, jaina, faber, criystal ) with large waste couplings is 13983 1994 over all size bowl size(inches) (inches)24 x 18 x 8 20 x 16 x 8 55 p & f looking mirror with pvc frame of approved (atul/ equivalent)size 500 x 400 mm 56 providing and fixing towel rail or ring of approved quality / make. c.p. brass towel rail with brackets 450 x 20 mm. 57 providing and fixing soap dish or tray of approved quality / make. c.p. brass 58 providing and fixing bath shower of approved quality / make. c.p. brass of heavy & superior quality 150 mm. 59 providing & fixing c.p. flange for 15 mm dia taps 60 p & f bib cock (is: 8931 mark) superior quality of approved make c.p. brass bib cock, 15 mm nominal bore 61 providing and fixing inlet connection (angle, valves) superior quality, of approved make.for wash basin gyser etc.c.p. inlet connection 15 mm.brass (is: 8931 marked) 62 providing and fixing 15 mm dia connection pipe of approved quality / make. pvc pipe with cp brass nuts upto length 600 mm 63 providing and fixing flush cock / flush valve (is : 9758 mark) for wc of approved quality make. c p brass half turn exposed 25 mm nominal bore 64 providing and fixing full way valve (is : 778 mark) or wheel valve of approved make. gun metal 15 mm nominal bore 65 providing and fixing full way valve (is : 778 mark) or wheel valve of approved make. gun metal 25 mm nominal bore 66 providing and fixing pvc storage tank confirming to is : (12701 marked indicating the bis license no) of approved make with cover, 25 mm dia 1 m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design.500 litres capacity 67 hoisting charges for each floor. 68 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work exposed on wall) 20mm nominal outer dia pipes 69 providing and fixing 3 layer pp r (polypropylene random coplymer ) pipes sdr 7.4 uv stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all pp r plain & brass threaded polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of engineer in charge. (external works)pn 16pipe, 32 mm od 70 providing and laying c.c. 1 : 5 :10 (stone aggregate 40 mm nominal size) upto haunches of s.w. pipes including 150 mm thick bed concrete as per rajasthan pwd specifications : (width w = dia of pipe in cm + 40 cm.) concrete width to be reduced from width w at centre of pipe to 0 at top of pipe.(excluding cost of pipe )100 mm dias.w. pipe 71 providing and fixing rigid pvc pipe (is : 4985 mark) class ii (4 kg./cm2) approved quality / makeincluding jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia 72 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia coupler (socket) 73 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia plain tee 74 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia bend 45° 75 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia bend 87.5° 76 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia vent cowel 77 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia pipe clip 78 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 450 x 450 mm depth upto 0.5 m cement coverwith frame 79 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 600 x 450 mm upto depth of 0.5 m cement cover with frame 80 construction of soakage well in all types of soil 300mm thick dry stone masonry, top and bottom 300 mm course in cm 1 : 6, 80 mm thick stone slab, jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m 15 grade c.c. flooring earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr. size 240 cm dia outside & 240 cm depth 81 construction of septic tank in all types of soil with 40 cm. thick masonry in cm 1 : 6, 15 cm. thickc.c. bed of 1 : 5 : 10, m 15 grade c.c. flooring & over stone slab covering, 80 mm thick slab, jointing of slab in cm 1 : 3 ralthal, kharanja, 50 mm thick stone partition walls, 20 mm thick plaster in cm 1: 6 finished with neat floating cement, 4 nos c.i. foot rests of approved design, two no. 450 mm dia 25kg. of each c.i. cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr. size 200 x 100 x 130 cm (for 10 users) 82 construction of cement concrete chamber 125mm dia on depressed floor upto 45cm height from floor with : stainless steel sheet grating 83 wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical/ wiring accessories refer chapter e 04, e 05 & e 07 . for additional technical parameters of products/ work , refer annexure a attached with this bsr short point (up to 3 mtr.) 84 medium point (up to 6 mtr.) 85 long point(up to 10 mtr..) 86 wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles, 18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, 3/ 5 pin 6 a modular socket, modular face plate with grid plate, screws etc,all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical/ wiring accessories refer chapter e 04, e 05 & e 07. for additional technical parameters of products/ work refer annexure a attached with this bsr on board 87 medium point (up to 6 mtr.) 88 s&f following sizes (dia.) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 20 mm 89 25 mm 90 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure a attached with this bsr 2 x 2.5 sq. mm. + 1x1.5sqmm 91 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 92 supplying and fixing of power plug point with modularaccessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 18 swg with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of isi marked modular 16 amp. switch (is :3854) and 3/5 pin 16 amp. socket outlet (is:1293) [ as per detailed in respective item in bsr] , making connection , testing , etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 93 providing & fixing of modular type step fan regulator duly isi marked (is :11037) as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm, including all as per pre approved by engineer in charge,making connections, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 5 step fan regulator 100 watt 2 module 94 providing & fixing of heavy duty capacitor start, copper woind double ball bearing 900/1400 rpm single phase exhaust fan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached withthis bsr .300 mm sweep(900/1400 rpm) 95 providing & fixing of ik07 ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum lm6/ adc12 material with heat dissipation fins on housing with uv stabilized pc/toughened glass cover (uv stablzation report submitted for uv cover ) and secondary lens on each led & should be smd type . the system level luminaire efficacy >=120 lm/ wt with high power leds is to be used and potted driver must be potted & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety ,input frequency 50hz±3% power factor >0.95 driver efficiency >85% ,thd(i) <10% humidity 10% to 90% rh working temp 5c to 45c . driver current <1000ma shown in lm79 report. the luminaire shall be bis certified and t.c. certified. life expectancy equal or more than 50000 burning hrs with minimum 70% lumenmaintened,colorrendering index>70 andcct 5700k+355k. surge protection shall be min = 4 kv internal and min 10 kv external. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr led street light fixture 70 watt 96 providing & fixing of 240/415 v ac mcb with positiveisolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with thisbsr .single pole mcb6 a to 32 a rating 97 double pole mcb50 63 a rating 98 providing & fixing of ik09 recessed/surface mountingheavy duty horizontal type sheet steel of 1.6 mm thick distribution board as per pwd specification for electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal db terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submit nabl / cpri/ erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr ip 43 double door (single phase)6 way (6 o/g +2 i/c ) 99 supply & laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with gi/cu thimble etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 8 swg copper wire 100 providing & fixing of ip40 led recessed / surface mounted, round / sqaure non dimmable back lit smd mid power led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal/ external bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and in compliance to iec standards. system lumen efficacy of = 120 lm / watt, thd < 10 % ,p.f.=0.95, cri >80, life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) ,maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsrrecessed mountingled downlight 18/20w 101 providing & fixing of ip40 led surface/ recessed / suspended mounting mid power smd type led light fixture made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 2.5 kv internal/external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection and in compliance to iec standards (integral with light fixture). system lumen efficacy of = 120 lm/watt ,thd < 10 % , p.f.=0.95,cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsrrecessed mounting36w led light fixture 2x2 with acrylic / prismatic front cover 102 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr.4 led tube shape fixture 18/20 w (polycarbonate base) 103 sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1):2004 of medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below : (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri/ erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second(b) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987,ieee 80 2013 (clause 14.5d) , ieee 837 & ier 1956 with latest amendemnts©heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm.(d) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.(e) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .with pipe in pipe technology (outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewellgi pipe 2000 mm long, 80 / 50 mm, terminal 50mm x 6 mm gi strip 104 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below: (a) material : h4 grade aluminium conductor of purity >99.6 %& as per is:1554 p i / is :7098 p i(b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures .(c) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type test certificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . armoured cable10.0 sq. mm2.0 core 105 providing & fixing of iso certified company made bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan as per pwd specification for electrical works, conforming to is:374 2019, & is:1885 p v 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 1200 mm sweep bee 2 star rated (service value >=4.5 to < 5 ) 106 supply & fixing of abc type (map 50) type powder fire extinguisher (stored pressure type) of following capacity duly current and valid bis certification conforming to is: 15683:2006, with dry chemical powder used as extinguishing agent should be mono ammonium phosphate 50% concentration conforming to is 14609:1999. oem will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket including initial fill and wall suspension complete in all respect. serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. the firm should submit the product certificate from an en notified body & product performance test report from nabl accredited lab as per is 15683. . all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 4 kg 107 supply installationtesting&commissioningofisocertified manufacturer made monoblock motor pump set isi marked (is:9079 2002) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single/three phase ( 240 440 v ) permanent split capacitor type (psc), fitted with thermal overload protection, . including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 0.5 hp, 1 ø, (3 18)mtr, (100 26) lpm 108 construction of tube well 100 metre depth and above in all type of rocks by dth system and over burden, to accommodate casing pipe of following size in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per is : 2800 (part i & ii) 1979 specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe. 200 mm dia nominal bore 109 development of tube well as per is specifications using suitable compressor to give sand free water for required yield of the gravel packed tube well. 110 supply of erw m.s. black casing pipe isi marked (is : 4270/1992) of grade fe 410 of following sizes at site of work. nominal bore of pipe200 (mm) 111 supply & fixing tube well cover of m.s. sheet (6 mm thick) with nuts and bolts complete for casing size. 200 mm dia 112 supply & fixing m.s. clamp, set of 50 x 6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 113 providing & fixing of single stage, water cooled, high speed(2880 rpm), horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t/c vs t/c, thrust bearing shall be of carbon + s.s.the stator body of single phase pump shall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition (ced) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 2.0 hp, 1 ø, (12 25) mtr, (350 115) lpm 114 supplying andlaying isimarkedp.v.c. insulated submersible cable as per pwd specification for electrical works confirming to is:694 and as per is 8130 : 2013 of 1.1 kv grade .wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4 including making connection etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. all as per pre approved by engineer in charge, making connections. for additional technical parameters of products/ work , refer annexure a attached with this bsr 6.0 sq.mm 3 core flat / round 115 providing & fixing of hdpe pipe isi mark (is:4984/2016 ) for watersupply (suitable for submersible & jet pump) with required fittings ie socket, elbows, tee etc. complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 50 mm od 6 kg / cm2 116 construction of 185 cm. dia platform as per approved design and drawing of unicef. 117 supply installation testing & commissioning of iso certified company made dol/star delta starter panel made out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / off push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr for single phase submersible / monoblockpump0.5 hp to 3.0 hp (dol starter) ...

Due Date : October 17, 2022

Tender Value : ₹ 38 Lakhs

View Tender
39
Military Engineer Services - Rajasthan

34098552 special repair to bldg no. t 39 and special repair to road furniture item at mil cantt ajmer under ge nasirabad. special repair to bldg no. t 39 and special repair to road furniture item taking down cement or cement lime plaster on stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 2 m& l for 15 mm thickrendering in cement mortar ( 1:6 ) , on stone masonary surfaces finished even and smooth, complete all as specified and directed 3 m&l for rendering 15mm thick in cm 1:4 on stone masonry, external surfaces finished even and smooth, complete all as specified and directed 4 m & l forpreparation ofnew plastered surfaces of wallsand providing two coat of cement base paint over a coat of primer, complete all as specified and directed. 5 m & l forpreparation old decorated surfaces of wallsand providing one coat of cement base paint complete all as specified and directed. 6 m & l for complete removal of existing treatment andpreparationwall surfaces and applying two coats of oil bounddistemperover a coat of primer over 1 mm thick wall care of putty complete all as specified and directed 7 m&l for preparation of new plastered surfaces and applying two coats of oil bounddistemperover a coat of primer over 1 mm thick wall care of putty complete all as specified and directed. 8 m&l for preparation of old wooden surfaces of any descriptionover 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 9 m&l for preparation of old concretesurfaces of any descriptionover 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 10 s & f second class hw 35mm thick, factory made, plain framed, paneled shutter ( three panels ) with panels of 9mm thick bwpgrade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to is 710. the size of rails & style shall be as per is 1003 ( part i ) kiln seasoned & chemically pressure treated complete all as per specified and directed. 11 s&f 2nd class hw 35 mm thick, gauged and skeleton shutters ( three panels ) , factory made open rebated and prepare to receive glass, gauge etc ( with sash bar ) , edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. size of members of shutter shall be as specified in ssr 2009 part i, section 8 clausemember shall be kiln seasoned& chemically pressure treated complete all as specified and directed. 12 s&f steel window / ventilator glazed and gauged ( combination ) with side hung / top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary ac / cooler arrangement in window & guard barscomplete all as as specified and directed. note : wire mesh and sheet glass shall be measured & paid separately under respective items. 13 s & f aluminium handle fabricatedtype, anodised 150mm size conforming to is complete all as specified and directed. 14 s & f 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all asspecified anddirected. 15 s&f aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 16 s&f mild steel butt hinges, medium weight, cold rolled, isi marked of size 100 mm, complete all as specified and directed. 17 m & l for rolled mild steel work angle ironas in door frame ( chowkhats ) of frame confirming to fe 290 or fe 330 including complete all as specified and directed. 18 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) exc 1.50 sqm and n.exc 4.00 sqm each and removing from site complete and making good disturbed surfaces of wall in cm ( 1:3 ) all as specified and directed. 19 taking down unserviceable chowkhats or frame with shutters ( without taking off shuters from the frames ) of any description n exc 1.50sqm and removing from site and making good disturbed surfaces of wall in cm 1:3 complete all as specified & directed. 20 m & l for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of ist quality over a coat of pink primer complete all as specified and directed. 21 m&l for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed. 22 s&f stainless steel wire cloth 0.36mm nominal dia of wire & average width ofaperture 1.40mm & fixed with wire staples complete all as spd & directed. 23 s&f 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 24 s&f in repair road stud ( cat eye ) abs bodyconforming to irc 67 1977giving reflection on both sides including fixing with epoxycomplete all as specified and directed. 25 s&f in repair solar road studs made up of highly compressive materials , water resistant alluminium alloy and polycarbonates 122 x 122x 20mm with 6 ledprismatic reflective lens on each side with stemfixed inroadcomplete all as specified and directed by engineer in charge. 26 m&l for 2 3 mm thick and 100 mm wide thermo plastic reflective painting white or golden yellow all as specified as on road surfaces in marking speed breakers, centre line, edge line etc complete all as specified and directed. 27 exavating in post holes ( or similar holes ) each n.exc 0.5 cum getting out in soft / lose soil returning, filling in and ramming earth in layers n.exc 25cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed. 28 m&l for pcc 1:3:6 type c 2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as specified and directed. 29 m&l for 1.65mm thick & 50 mm bore ( outer dia 60.3mm ) stainless steel pipe of schedule 5 s sign board complete all as specified and directed. 30 s&f informatory sign board in reqd size and each sign board made of two 4mm thick aluminium composite panel ( acp ) , both side face to fully covered with 3m scotchlite brand high intersity prismatic grade retro reflective sheet shall be astm d 4956 type iv in required colour.the retro reflective sheet shall be processed on acp by 3m equipment heat lamp vacum applicaror and letter, signs and symbol shall be cut by computerized plotter or digital printed on retro reflective sheet with high quality eco solvent digital roland and fabricated out of high internsity prismatic grade sheeting with text matter ( as reqd ) and border of same sheeting.signboard shall be supplied along with supported circular hollow stainless steel section frame of size 25mmx25mmx1.29mm thick along with proper clamping with same section of stainless steel and nut bolts / welding, complete all as specified and directed. 31 s&f guide post delinators model no. 952 gp abs round body fitted with 2 nos 100 mm dia highly reflective reflectors made out of pmma and mounted on ms pipe of 50 duly powder coated, anti rust & anti theft steel net make ( dark eye ) complete fixing incl necessary excavation, pcc etc required complete all as specified and as directed by the engineer in charge. 32 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from siteand making good disturbed surface of walls, floors etc complete all as specified and as directed by the engineer in charge. 33 disconnecting unserviceable sub main wiring / service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and as directed by the engineer in charge. 34 taking downmcb dbs complete with mcbs / isolator etc removing materials from siteand making good disturbed surface of walls, floors etc complete all as specified and as directed by the engineer in charge. 35 m&l for point wiring with 1.5 sqmm, pvc insulated, unsheathed, stranded copper conductor single core frls cable, is 694 marked, drawn through and including non metallic rigid pvc concealed conduit 20mm dia or higher complete with all pvc conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. / fittings isi marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 sqmm stranded copper conductor pvc insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for: 36 one light point controlled by one, one way switch. 37 one ceiling fan / exhaust fan point controlled by one, one way switch. 38 one three pin 5 amp socket on same board with other switches. 39 one 3 pin 5 amp socket on independent board. 40 all as per item no. 35.00 here in before but with 2.5 sqmm, for one 5 pin 5 / 15 amp socket on independent board including 2.5 sqmmstranded copper conductor ( frls ) pvc insulated green in colour as continous earth conductor connected to common earth complete all as specified and as directed by the engineer in charge. 41 s&f of submain wiring with two runs of single core pvc insulated and unsheathed multistranded ( frls ) copperconductor cable of size 6.00 sqmm lt, 1100 volts grade, drawn through and including 25 mm dia or higher pvc nonmetallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistrandedcopper conductor cable green colour as earth continuity conductor complete all as specified and as directed by the engineer in charge. 42 s&f switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and as directed by the engineer in charge. 43 s&f switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and as directed by the engineer in charge. 44 s&fsocket outlet 3 pin 5 / 6 ampflush type complete all as specified and as directed by the engineer in charge. 45 s&fsocket out let 2 in 1, multipurpose 3 pin 15 / 16 amp flush type isi marked complete all as specified and as directed by the engineer in charge. 46 s&f ceiling fan regulator electronic flush , steped ( four step ) 230 volts ac complete all as specified and as directed by the engineer in charge. 47 s&f ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and as directed by the engineer in charge. 48 s&f of lamp holder pvc / polycarbonate type with back plate complete all as specified and as directed by the engineer in charge. 49 s&f led tube light fitting in acrylic linear tube ( 1x 18 watt ) , 230v for single led tube lightincluding 1 x 18 w ledretrofitbar professional cw 6500 k cover channel, bipin holders, led power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. make : havells cat part no photonultra2.01212t8sstl20wled 865spc ( for tube ) regalbattent8upto1x22wdsbswh ( for batten ) bajaj cat part no blrb 18w cwc for tube , blrb db 118 for batten , or equivalent model of philips / crompton 50 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.make : bajaj / havells / cg 51 s & f led light fitting 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.make : bajaj / havells / cg 52 supply and fixing testing and commissioning energy saving street light luminaire 35 watt led , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, ip 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by engr in charge. make havells cat part no enduracityliteplat plussl35wled757sasybopc or equivalent model ofsurya / control& switchgear / bajaj 53 supply and fixingstreet light bracket made of 32 mm gi pipe , 1.2 mtr lenght fixed withtwo nos of clamp , nut and bolts for fixing of street lightcomplete all as specified and directed by engr in charge. 54 s & f of mcb sp, 240 volt, 6 amp to 40 amp capacity, 10 ka, c curve complete all as specified and directed. 55 s & f of mcb spn, 240 volt, 63 amp capacity, 10 ka, c curve complete all as specified and directed. 56 s&f of mcb distribution board single pole & neutral with 200 amps rated bus bar, double door ip 43 dbs , made outof sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing mcbs including blanking platecomplete all as specified and as directed by the engineer in charge. 57 s&f exhaust fans ac single phase 230v of size 300mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.make : usha / crompton / bajaj 58 m&l for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore gi med grade with funnel and wire mesh pcc chamber in cement concrete 1:3:6 type c 2 and rcc cover with handle all as specified and shown in elect plate no 3 of ssr part i of 2009 incl dismantling of old unserviceable existing earthing complete all as specified and as directed by the engineer in charge. 59 s&f of led lamp 9 / 10 watt complete all as specified and as directed. make : havells / crompton / bajaj / usha 60 supply & fixing ceiling fan 1200 mm sweep , 230 volts, ac , 50 hz, copper winded motor, bee 5 star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and as directed.make: crompton / havells / orient 61 s&f single pole and neutral enclosure with a two pin and earth plug and earth plug and socket complete with one single pole 20 amp mcb sp c series for ac complete all as specified and directed. 62 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and as directed by the engineer in charge. 63 supply and fixingtubes light grade gi tubing 40 mm dia withall fitting laid in trenches, fixed on pole / on wall for cable protection complete all as specified and as directed by the engineer in charge. 64 excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed. 65 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft / loose / hard / dense soil complete all as specified and as directed. 66 removing excavated material ( soils ) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point 67 supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed.note: depth of sand cushioning will be measured after punning down and levelling the sand properly. 68 m&l for laying of bricks locally available sub class b bricks, non modular sizes as per is 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed. 69 total in figures 70 quoted amount in words...

Due Date : October 24, 2022

Tender Value : ₹ 9 Lakhs

View Tender
40
Department Of Defence - Rajasthan

33603659 bids are invited for door with ms angle frame 0.90 mtr x2.10 mtr with 19 mm plywood shutter and complete accessories, size of angle 35mm x35mm x 5 mm thick, panel design as per buyer choice , window size 1.2 mtr x 0.90 mtr with aluminum frame double shutter 4 mm glass and wire mesh, panel design as per buyer choice , pvc paneled door size 6 feet x 2 feet with aluminum frame heavy duty, panel design as per buyer choice , aluminium sliding door size 4 feet x 7 feet complete set with frame, heavy duty, panel design as per buyer choice , aluminum sliding door size 5 feet to 6 feet x 7 feet with frame complete set heavy duty, panel design as per buyer choice , door with ms angle frame 1.2 mtr x 2.10 mtr with 19mm plywood shutter with complete accessories, size of angle 35mm x 35mm x 5mm thick, panel design as per buyer choice , aluminum sliding door size 5 feet 8 inch x 7 feet complete set with frame, heavy duty, panel design as per buyer choice , steel window size 5 feet x 4 feet with ms angle frame double shutter 4 mm glass and wire mesh fitted size of angle 30 mm x 30 mm x 5mm thick, panel design as per buyer choice , aluminum sliding door size 3 feet x 7 feet complete set with frame heavy duty, panel design as per buyer choice , steel window size 4 feet x 3 feet with ms angle frame double shutter 4 mm glass and wire mesh fitted size of angle 30 mm x 30mm x 5 mm thick, panel design as per buyer choice , aluminum main door size 7 feet x 4 feet complete set with frame, heavy duty, panel design as per buyer choice...

Due Date : August 23, 2022

Tender Value : ₹ Ref. Documents

View Tender
41
Department Of Defence - Rajasthan

33447761 bids are invited for door with ms angle frame 0.90 mtr x2.10 mtr with 19 mm plywood shutter and complete accessories, size of angle 35mm x35mm x 5 mm thick, panel design as per buyer choice , window size 1.2 mtr x 0.90 mtr with aluminum frame double shutter 4 mm glass and wire mesh, panel design as per buyer choice , pvc paneled door size 6 feet x 2 feet with aluminum frame heavy duty, panel design as per buyer choice , aluminium sliding door size 4 feet x 7 feet complete set with frame, heavy duty, panel design as per buyer choice , aluminum sliding door size 5 feet to 6 feet x 7 feet with frame complete set heavy duty, panel design as per buyer choice , door with ms angle frame 1.2 mtr x 2.10 mtr with 19mm plywood shutter with complete accessories, size of angle 35mm x 35mm x 5mm thick,panel design as per buyer choice , aluminum sliding doorsize 5 feet 8 inch x 7 feet complete set with frame, heavyduty, panel design as per buyer choice , steel window size 5feet x 4 feet with ms angle frmae double shutter 4 mm glassand wire mesh fitted size of angle 30 mm x 30 mm x 5mmthick, panel design as per buyer choice , aluminum slidingdoor size 3 feet x 7 feet complete set with frame heavyduty, panel design as per buyer choice , steel window size 4feet x 3 feet with ms angle frame double shutter 4 mm glassand wire mesh fitted size of angle 30 mm x 30mm x 5 mmthick, panel design as per buyer choice , aluminum maindoor size 7 feet x 4 feet complete set with frame, heavyduty, panel design as per buyer choice total quantity : 169...

Due Date : August 11, 2022

Tender Value : ₹ Ref. Documents

View Tender
42
Military Engineer Services - Rajasthan

33421946 provn of clothing and medical store at army area under ge shikargarh jodhpur excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed. 2 m&l pcc 1:4:8 type d2 ( 40 mm graded aggregate ) in foundation filling and mass concreteetc complete etc.all as specified and as directed. 3 m&l for brick work with fly ash bricks ( old size bricks ) , straight or curved on plan exc 6mtr mean radius, built in cement mortar ( 1:6 ) complete all as specified and as directed. 4 m&l for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides of soffits ( if any ) of foundations and plinth beams and similar work etc; rough finish surfaces complete all as specified and as directed. 5 m&l for form work to sides of concrete pillars, posts, struts, piers, columns and stanchion etc; rough finish surfaces complete all as specified and as directed. 6 m&l for form work to sides and soffits of floor or roofrcc beam sides of lintel beam flat rough finish surfaces to receive the plaster, complete all as specified and as directed. 7 m&l for formwork for chullah hoods, chajjas through and similar items including edges, surface rough finish surfaces to receive the plaster, complete all as specified and as directed. 8 m&l for form work to soffits of suspended slabs such as roof slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) , rough finish surfaces complete all as specified and as directed. 9 m&l for form work to edges of concrete flats, floor and roofs not exceeding 20cm wide ( horizontal or sloping ) , rough finish surfaces complete all as specified and as directed. 10 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in foundations, including raft footings, foundations beams, plinth beams, bases of columns etc; complete all as specified and as directed. 11 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in columns, pillars, piers, posts and struts etc; complete all as specified and as directed. 12 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in beams, lintel up to 1.5m clear span, lintel bands etc; complete all as specified and as directed. 13 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in slabs supported on walls, beams and columns in roof, landings, balconies, canopies and in shelves etc; complete all as specified and as directed. 14 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in chajjas etc; complete all as specified and as directed. 15 m&l for reinforcement 10mm dia and over tmt bars cut to length, bent to shape required and binding with ms wire not less than 0.9mm dia or securing with clips complete all as specified and as directed. 16 m&l for reinforcement 8 to 10mm dia tmt bars cut to length, bent to shape required and binding with ms wire not less than 0.9mm dia in stirrupscomplete all as specified and as directed. 17 m&l for carrying out water proofing treatment forroofs in the following stages ( i ) rendering 10mm thick in 1:4 mixed with integral water proofing liquid all as per manufacturers instructions over concrete surfaces finished even and smooth with out using extra cement. ( ii ) first coat of bitumen primer confirming to is 3384 @0.300 kg / sqm over plastered surafces ( iii ) secondlayer of 3.0 mm thick app modified polymeric membrane with centre core of single non woven polyster reinforcementandhaving weight 3 kg / sqm with mineral gravel finish on top complete laid with blown type bitumen grade 85 / 25 @ 1.20 kg / sqm complete all as specified and as directed. ( iv ) finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against uv, including preparing of old surfaces of roof remove all corrosion products brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of painted surfaces ( second coat apply after 24 hrs or as per manufacturing instructions ) . 18 supply only integral water proofing liquid isi marked make: pidiproof lw 19 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm each layer in hard / dense soil all as specified and directed. 20 removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point all as specified and directed. 21 m&l for 15 mm thick rendering on stone / brick masonary wall surfaces in cm 1:4finished fair and even all as specified and as directed. 22 m&l for rendering 15 mm thick in cm 1:6 finished even without using extra cement over stone wall surfaces all as specified and as directed. 23 m&l for 10mm thick rendering in cm 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed. 24 m&l for 75mm thick pcc 1:4:8 type d 2, ( 40mm graded stone aggregate ) as in sub floor, sub bases, floor and paving etc; complete all as specified. 25 m&l for pcc 1:2:4 type b0 25 mm thickusing 12.5mm graded stone aggregates as in sub floors / base floors under tiles as in levelling course etc all as specified and directed. 26 m&l for machine cut kota stone slab flooring 18 20 mm ( + 2mm ) thick over cement screed base laid and jointed with greycement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in cm 1:4 complete all as specified and as directed. 27 m&l for mirror polished machine cut kota stone slab 15 16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in cm 1:4 and jointed complete all as specified and as directed. 28 m&l for 16 18mm thick granite ( colour as approved ) work ( table rubbed and polished ) in steps, shelves, jambs, pillars, window cills, cooking platforms ( vertical / horizontal ) and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in cm 1:4 complete all as specified and as directed. 29 cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified. 30 pressed steel framed made out of 1.25mm thick ms sheet, of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed. 31 cement concrete ( 1:3:6 ) type c 1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc., complete all as specified 32 cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stoneaggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bedblocks of hold fasts etc including necessary form work complete all as specified 33 s&f of factory made 35 mm thick plain framed, panelled shutters ( two panel ) with 2nd class hard wood rail and stylewith lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 ( part i ) , kiln seasoned and chemically pressure treated complete all as specified. 34 s&f of factory made steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8 / 10mm square bars as directed by engineer incharge, fixed horizontally @ 10cm c / c, hinges, handle, tower bolts, stops, lugs etc. ( with provision of fixing for cooler if required ) all as shown on drawing no cejz / td / 20 sheet 1 / 3 to 3 / 3 fixed in repairs i.e, incl taking down and removal of old steel windows from site or to store complete all as specified and directed. note: guard bar / grillshall be measured and paid separately under respective item of sch a. 35 s&f of sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed. 36 mild steel round bars welded to steel windows or ventilators as in guard bars framed or unframed complete all as specified & as directed by engineer incharge.note: guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. cost of factory welding & shop coat of primer is deemed to be included in quoted rates. 37 s&f mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified. 38 s&f of mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified. 39 s&f of 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified. 40 s&f of framed work as in doors chowkats of ms angle iron or ms hollow square / rectangular any type / size with gusset plates, rails, braces, cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to fe 290 ( gde e 165 ) complete all as specified and directed by engineer in charge. 41 m&l for 100mm thick pcc 1:4:8 type d 2, ( 40mm graded stone aggregate ) as in sub floor, sub bases, floor and paving etc; complete all as specified. 42 m&l for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg / sqcm, of shape and colour as approved by ge , laid over 25mm thickcompacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed. 43 m&l for factory made precast cement concrete solid blocks m 30 grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size ( with plain or interlocking joints as directed ) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish / surplus soil etc., complete all as specified and directed by engineer in charge. 44 m&l for cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified. 45 preparing new plastered surfaces and m&l for applying chalk whitening / concrete primer and / or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and m&l two coats of distemper oil emulsion on new plastered surfaces all as directed by engr in charge. 46 preparing new plastered surfaces and m&l for applying concrete primer and / or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and m&l two coats of cement base paint on new plastered surfaces all as directed by engr in charge. 47 preparation of newplastered surfaces of ceiling etc. & applying three coats of limewhite wash on ceilingcomplete all as specified. 48 preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 49 preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paint complete all as specified andas directed by engineer in charge.. 50 m&l for point wiring ( concealed ) one light / fan point controlled by one 5 amps one way switch with 1.5 sqmm ( nominal area ) copper conductor flame retardant low smoke cable ( multi stranded ) pvc insulated and unsheathed electric cable 1100 volts ( isi marked ) drawn through pvc concealed conduit of suitable size ( as per conductor run ) with all fittings and accessories including pvc insulated unsheathed electric cable 1100 volts 1.5 sqmm ( multi stranded ) copper conductor single core ( green colour ) as continuous earth wire connected to common earth dolly including metal flush box made out of ms with hylum sheet suitable size and shape complete all as specified and directed by engineer in charge.. 51 all as per item no 50 above but for one 3 pin socket outlet 5 amps on independent board 52 all as per item no 50 above but for one 3 pin socket outlet 5 amps on same board 53 all as per item no 50 above but for one 3 pin socket outlet 15 ampsindependent with cable of size 4.0 sqmm for point wiring and 4.0 sqmm in continuous earth wire complete all as specified and directed by engineer in charge. 54 s & f switchpiano type 1way5a, 1 module 240 volts complete all as specfied and directed by engr in charge. 55 s & f switchpt 1way15a, 1 module, 240 volts complete all as specfied and directed by engr in charge. 56 s & f socket, 6a 2 / 3 pin combined 2 module, complete all as specfied and directed by engr in charge. 57 s & f socket6a / 16a 2 / 3 pin combined 2 module, complete all as specfied and directed by engr in charge. 58 s & f lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by engr in charge. 59 supply and fixing led lights fitting 1x 18w, 220v ac, metal ray plus is made of extruded aluminum channel with decorative dual color end caps providing a glare free evenly distributed light with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 60 supply and fixing led street light fitting 35 watt 230 v ac outdoor type with pressure die cast housing with toughned glass ingress protection of ip66, high power smd leds and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete all as specified. 61 ceiling rose surface backelite isi marked with 3 terminalincluding connecting and testing complete all as specified and dirted by the engineer in charge. 62 s&f distribution board sheet encloser powder coatedfor mcbs with bus bar 250 amps rated and neutral link earthing stud and degree of protection ip43 with door / mechanical resistance ik 07, spn 8 way 240 volts double door, concealed flush to wall surface complete all as specified and directed by the engineer in charge. 63 s&f distribution board sheet encloser powder coatedfor mcbs with bus bar 250 amps rated and neutral link earthing stud and degree of protection ip43 with door / mechanical resistance ik 07, spn 4 way 240 volts double door, concealed flush to wall surface complete all as specified and directed by the engineer in charge. 64 s& mcb, c curve type, 10 ka, 6 to 32 amp, single pole with over load and short circuit protection, complete all as directed. 65 s&f mcb, c curve type, 10 ka, 40amp, spn with over load and short circuit protection, complete all as directed. 66 supply and fix exhaust fan, steel body ac single phase. 230v of size 300m sweep with, blades, and frame and louvers with necessary making hole and finishing work as reqd at site complete all as specified and directed. 67 supply and fixing ceiling fans complete with blades, down rods, with 2 module electronic step type regulator and accessories, 230 v, 1200 mm sweep. min air delivery 210 cfm with service value 6.00 bee. 5 star rated with brushless direct current motor ( bldc ) compele all as specified and directed. 68 s&f vertical distribution board, double door, suitable for a frame fp mccb 125a made out of crca mild steel sheet surface with insulated material like polyester or with epoxy powder coating, vtpn 4 way, 415 volts with bus bar rating 250 amps, dust and vermin proof, suitable for incorporation of mcb’s and mccb etc and making all necessary connections, concealed flush to wall surface, complete all as specified and directed. note : mccb & mcb will be measured and paid separately under respective items 69 s&f mccb, a frame, thermal adjustable magnectic setting, ics = 75% 25 ka, 415v, 125 amp, 4 pole mccb with over load and short circuit protection, complete all as directed. 70 supply and fixing concealed sub main wiring with 2x10 sqmm single core copper conductor ( multistandered ) in concealed pvc frls conduit of suitable size as required, including single core 6.0 sqmm copper conductor as earth continuity all as directed. 71 supply, laying, testing and commissioning of lt ug cable, xlpe insulated, pvc sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 35 sqmm 3.5 core confirming to is:7098 ( part i ) , suitable for earthed system, laid in duct / trench / along pole / wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. 72 supply, laying, testing and commissioning of lt ug cable, xlpe insulated, pvc sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 10 sqmm 2.0 core confirming to is:7098 ( part i ) , suitable for earthed system, laid in duct / trench / along pole / wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. 73 earthing complete with galvanized steel earth plate electrode 600x600x6mm thickburied directly in ground ( earth pit not less than 2..25 mtr deep belownormal ground level ) with top edge ofearth plate not less than 1.5 mtr below the normal ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth lead gi wire 4mm dia ( 8 swg ) connectd to gi earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board and protected by galvanised iron pipe medium grade15mm bore and20mm bore medium grade gi pipewith funnel and wire mesh for watering all as shown in electrc plate no 5 connected to earth test point.40mm thick pre cast rcc m 15 ( nominal mix ) cover reinforced with xpm weight not less than 4 kg / sqm with suitable handle of 6mm dia ms bar and angle iron 40x40x3mm frame for cover, pcc chamber in cement concretem 15 ( nominal mix ) , excavation and earth work in any type of soil and connected all as specified and as directed by engineer in charge. 74 supplying and laying un reinforced precast concrete cable cover, class lv, type i, flat, size 250mm x 150mm x 40mm under ground cables for protection 75 m&l for sand cushioning with layer of sand 8cm thick before laying of cable and 10cm after laying of cable in trenches complete all as directed and sand cover to under ground cablecomplete all as directed. 76 m&l pipe galvanised iron light grade complete with all fittings laid in road crossing, and on pole, buildings complete all as specified and directed isi marked of 40mm bore...

Due Date : August 27, 2022

Tender Value : ₹ Ref. Documents

View Tender
43
Urban Improvement Trust - Rajasthan

32713522 various civil miscellaneous work in div. ii a ( arc ) civil works earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 2 cement concrete pavement of required thickness with (b) 1:1.5:3 (1 cement:1.5 course sand : 3 graded stone aggregate 20 mm nominal size) including finishing complete. 3 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 4 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand). 5 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto three levelabove 30cm. thick walls in :cement mortar 1:6 ( 1 cement : 6 sand). 6 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. 7 pointingonstonemasonryincementsandmortar 1:3 (1 cement : 3 sand) : flush / ruled/ struck or weathered pointing. 8 providing and laying damp proof course with cement concrete grade m 150 (1 : 2 : 4) mortar prepared with 1% solution of water proof compound complete as per specification .50mm thick. 9 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 50mmthickwith20mmthicknominalsizeaggregate. 10 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. 20 grade nominal mix 11 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. hot rolled deformed bars (is : 1139). 12 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 13 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 14 providing and fixing corrugated colour g.i sheet having thickness 0.50mm roofing fixed with g.i.j or l hooks bolts and nuts 8mm dia meetr with bitumen and g.i limpet washers or with g.i limpet washers filled with white lead and including over lapping of sheet complete ( upto a pitch of 60 degree) & excluding the cost of purlins rafters and trusses etc complete in all respect. 15 supplying and fixing of chain link fencing with angle iron posts 50x50x6mm placed at every 3 mtr. apart 30cm in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner and every tenth post to be strutted with (50 x 50 x 6cm) angle iron provided and fixed and fitted with posts including earth work in excavation etc. complete with chain link size. 16 50mm x 50mm x 3.15mm 17 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 18 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 19 one or more coats on old work. 20 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : 21 one or more coats on old work. 22 two or more coats on new work 23 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. 24 old work 25 new work 26 finishing wall with water proofing cement paint of approved brand and manufacture and or required shadetogive an even shade including all scaffolding: new work (two or more coats applied @ 3.84 kg/10 sqm). 27 old work (one or more coats). 28 clearing and grubbing road land including uprooting rank vegetation, grass, brush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000m from road boundary. (morth specification : clause 201). : in area of thorney jungle 29 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : walls (any thickness) including attached pilasters,buttressesplinthandstring course. 30 m 40,80mm thick to be used in medium traffic (medium trafficis defind as a daily traffic of 150 450 commercial vehicles exceeding 30 kn laden weight , or an equivalent of 0.5 to 2.0 msa for a design life of 20years) like city streets, small and medium market roads, low volume roads ,ytility cuts on arterial roads, etc. : category bdenated only two side like i,z,t shape etc. as per irc sp 63:2004 31 add extra for coloued 32 random rubble dry stone kharanja under floor. 33 providing stone slab covering over drains including filling of joints in cement sand mortar 1 : 3 with 35 mm thick cement concrete flooring 1 : 2 : 4 mix complete with good finish with :stone slab 40 to 50 mm thick average. 34 transportation of excavatedearth from site including loading – unloading etc. complete with all lead and lift.(for 5 km lead) 35 providing and laying m30 grade controlled cement concretepavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with 20/25 mm stone aggregate (crusher broken) including anti skid textured finish to required camber/ super lavation and grade including curing etc. as per specification with cement concrete m 30 grade including cost of steel frame work for sides of c.c. pavement consisting of m. s. channels flats and angles with required steel pegs ( some of them may left embedded in concrete/ including providing frame work 36 cutting of construction joint/ longitudinal joint 4 to 6 mm. wideusing mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealingcompound in groove including cost of sealing compound.100 mm depth 37 expansion joints raised type as per approved drawing. 38 providing and fixing 3 layer pp r (polypropylene random coplymer ) pipes sdr 7.4 uv stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all pp r plain & brass threaded polypropylene random fittings and fixing the pipe with clamps at 1.00 spacing. this includes testing of joint complete as per direction of engineer in charge.( internal work exposed on wall) pn 16pipe, 20 mm od 39 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge. 1: 3: 6 or richer mix. 40 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 41 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. in cement mortar. 42 demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge: in cement mortar. 43 dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead: of area exceeding 3 square meter. 44 taking out doors, windows and clearstory windows shutters (steel or wood) including stacking within 50 meters lead: of area exceeding 3 square meter. 45 dismantling wood work in frames, trusses, purlins andraftersupto10meterspanand5mheight including,levellingstackingthematerial within 50m lead: of sectional area 40 sq.cm and above 46 dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 47 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 48 dismantling chajja and shelves with care including making jhiries and making good : stone shelves. 49 repair to cement plaster in cement mortar 1 : 6 (1 cement : 6 fine sand) including removal of old plaster in regular shape and white or colour washing. 50 patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. 51 making the opening inmasonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground.for door/windows/clerestory windows 52 add extra item no. 13.15 for fixing of door / window frames (chowkhats or steel windows) in the opening including fixing hold fast in cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone grit 20 mm nominal grade) excluding the cost of frame or steel windows. 53 renewing glass panes, with putty and nails wherever necessary:float glass panes of thickness 4 mm 54 fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts embedding hold fasts in cement concrete blocks with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominaal size)painting two coats of coal tar to sides of chaukhats and making good the damages to walls and floors as required complete including disposal of rubbish to the dumping ground within 50 metres lead 55 door chowkhats 56 window chowkhats 57 providing and fixing double scaffolding system on the exterior side, upto five story made with 4 wodden member 1.5 m c/c horizontal and vertical direction joining with rassi, clamps, challies. the scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safty features for the workmen etc complete as per direction of ei.the lavation area of the scaffolding shall be mearured for payment. the paeyment will be made once irrespective of duration of scaffolding.note : this item to be used for maintence work judically 58 repair of existing steel glazed doors, windows and ventilator, ms sheet door, garge doors, compound wall gates etc. by welding drilling complete include. cost of welding rods and hire charge of welding meachine and tp etc complete 59 providing and fixing fully panelled double leaf shutters for windows and ventilators as per approved design and drawings with approval steel fittings as per annexure a and width of styles, bottom and top rails 75 mm including beading of 25 mm x 15 mm size on both faces. 30 mm thick nigeria teak wood grade i 60 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick . decorative teak veneer both side 61 rough chisel dressed stone flooring over 20 mm (av.) thick base in cm 1 : 6 including pointing with cement mortar 1 : 2 (1 cement : 2 stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm :35 mm thick red sand stone. 62 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 63 providing& fixing door, window, chowkhats and other frames, including antitermite treatment, m.s. flat, hold fasts of size 250 x 40 x 3mm fixed with m.s. bolt 5mm dia 50mm long duly embedded in cement concrete m 15 grade : sal wood grade i. ...

Due Date : June 30, 2022

Tender Value : ₹ 95 Lakhs

View Tender
44
Military Engineer Services - Rajasthan

32120085 repair to floor joinery , sanitary and plumbing items in tech area at af stn nal at ge ( af ) nal as described in bill of quantities 1 demolition of rcc of any descriptionand in any position not other wisespecially provided for ( reinforcement cut as required to faciliate demolition complete all as specified & directed. 2 demolition of cement concrete ( unreinforced ) in ground floor and paving exc.15 cm thickness above ground level and removing the rubbish outside mod land complete all as specified & directed. 3 dismantling floor, hearth wall tiling incld cement mortar bedding ( but not backing ) removing serviceabletiles to store & rubbish off the premises. note : the demolished material should be disposed off outside mod land. the contractor shall quote his rates considering the above element, no extra paid on this. 4 demolition of brick or stone masonrybuilt in cement mortarincl all quions, arches, pillar etc. complete all as specified & directed. 5 taking down cement plaster on brick or stone walls / ceiling etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed. 6 dismantling of stone slab and tiles of any descriptionor thickness in floors aprons etc, laid bedded and pointed in any mortar complete all as specified and directed. 7 dismantling plain or corrugated steel sheeting any gauge / thickness incl nainital pattern or similar pattern roof covering in patches complete all as specified & directed. 8 dismantling ac sheet ( corrugated / semi corrugated ) in roof covering including ridge etc. complete all as specified and directed. 9 dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 10 dismantling of wall / ceilingboards ( fibre, pvc, pulp, insulation etc ) of any description, any thickness including frame / grid, filletswork etccomplete all as specified and directed. 11 taking down of bird nettingof hangers at height exc 6.0 metre but n exc 10 metre and refixing in the same position including necessary repair to nettingcomplete all as specified and directed. 12 material and labour reinforced cement concerete1:2:4, type b 1 ( nominal mix ) using 20mm gradedcrushed stone aggregate ) as in slabs supported on walls, beams, columns, shelves and like complete all as specified & directed. note: reinforcement shall be measured and paid for separately under respective item of boq sch a. 13 material and labour reinforced cement concerete1:2:4, type b 1 ( nominal mix ) using 20mm gradedcrushed stone aggregate ) as in chajjas at approx up to 7 mtr heightand like complete all as specified & directed. note: ( i ) reinforcement shall be measured and paid for separately ( ii ) all scaffolding and necessary arrangements for casting at specified height shall be arranged by the contractor and included in the quoted rate. 14 use and waste of formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete complete all as specified & directed. 15 use and waste of formwork to soffits of suspended slab such as in chajjas; flat rough finished surfaces of concrete complete all as specified & directed. 16 use and waste of formwork to edges of concrete flats, treads, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed. 17 material and labour mild steel tmt bars 6 to 8 mm and abovecut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire ( annealed ) not less that 0.90 mm dia or securing with chips complete all as specified and directed. 18 material and labour 75mm thick pcc 1:3:6 type c 1 ( using 20mm graded aggregate ) as in plinth protectionlaid in alternate bays, surface finished even & smoothwithout using extra cement including making joints complete all as specified and directed. 19 material and labour 75mm thick pcc 1:4:8 type d 2 ( using 40mm graded aggregate ) thick as in sub base of floorsurface finished even & rough to receive floor topping complete all as specified and directed. 20 material and labour 25mm thick pcc ( 1:2:4 ) type b 0 ( using 12.5mm graded aggregate ) as in sub base of floorsurface finished even & rough to receive floor topping complete all as specified and directed. 21 material and labour 40mm thick pcc 1: 2: 4 type b 1, ( using 20mm graded stone aggregate ) as in floor & finishing the surface even & smooth using extra cement including fixing glass dividing strips complete all as specified and directed.note :glass dividing strips shall be measured and paid separately. 22 supply only glass dividing strips 3mm thick and 38mm wide inserted in position conform to design complete all as specified and directed. 23 material and labour glazed ceramic coloured tiles 7 to 8mm thick ( square / rectangular ) dark / printed in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm thick set & jointed in neat cement slurry and pointed with coloured cement to match, over and including 10mm thick rendering in cm 1:4 complete all as specified and directed. 24 m & l for glazed ceramic tiles in vertical surface 350x 250x 7 mm / 450x 350x 7mm thick, projected pattern elevation tile, set and jointed in neat cement slurry and pointed in white or colour cement to match including cement mortar backing coat of 10mm thick in cement mortar 1:4 complete all as specified and directed by engr in charge. note: i ) colour, type and pattern of tile shall be as apoproved by geii ) tile used shall be projected pattern elevation tile and the tenderer shall quote his rate accordingly. 25 material and labour non skid, ceramic, coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, in floors, set and jointed incement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed. 26 material and labour non skid, ceramic, coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed incement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in cm 1:4 complete all as specified and directed. 27 m&l for vitrified light shade ceramictiles10 mm thick polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cm 1:6 complete all as directed. 28 all as peritem no.27 above but in skirting and over 10mm cement backing in cm 1:4 complete all as specified and directed. 29 supply and layingchequred cement concrete tiles glossy finished 30mmx30mmx22mm thick made by table vibratory method set, jointed and pointed in neat cementslurry as in floors with grey cement & pigment tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6, complete all as specified and directed. 30 s&f in repair factory made rubber moulded, rubberized laboroda tiles, ( pre polished / glossy finish ) of pcc type a 1, of approved colour and shape of size 400mm x 400mm x 30mm thick, jointed with neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles, over 15 mm thick screed bed in cm1:6 complete all as specified and directed. 31 material and labour 18 to 20 mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, landings, window cills cooking plate form and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble duet with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and includingrounding of edges of graniteslabs 10 to 20 mm thick by grindingand rubbing and finished smooth, coloured as approved by ge all asspecified and directed.note: front facia edges of granite slabs shall be rounding and finished smooth. the contractor shall quote his rates considering the above element, no extra paid on this. 32 all as per item no. 31.00 above but as on vertical surfaces and over 10 mmthick rendering in cm 1:4. 33 m&l fine sand filling under floors or in foundations including watering and consolidation for interlocking paver block and similar works etc complete as specified and directed. 34 m&l machine pressed precast concrete coloured interlocking paver block of approved shape and size confirming to is 15658 2006 of 60 mm thickness with grey cement and no pigment, m 35 grade of approved colour and design complete all as specified and directed 35 all as per item no. 34 above but 80 mm thick m40 grade. 36 all as per item no. 34 above but 100 mm thick m50 grade. 37 providing and laying at or near ground level factory made kerb stone of m 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm ) , including making drainage opening wherever required complete and as directed. 38 material and labour for brick work with sub class b bricks old size, straight or curved on plan exc 6m mean radiusbuilt in cm 1:6. complete all as specified & directed. 39 all as per item no. 38.00 above but as in half brick thick wall built in cm 1:4 complete all as specified & directed. 40 material and labour 15mm thick rendering on other than faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed. 41 material and labour 10mm thick rendering on concrete surface in cm 1:3 as in ceiling surface to be finished even and smooth without using extra cement complete all as specified and directed.. 42 material and labour 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed. 43 material and labour two coats of white wash on newly plasteredsurfaces of wall including preparation of surfacescomplete all as specified and directed. 44 preparingsurface of new plastered surface and applying two coat of oil bound distemper emulsionover one coat of primer complete all as specified and directed. 45 material and labour three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed. 46 preparingsurface of new plastered surface and applying two coats of acrylic emulsion exterior paintover coat of primer, tint as approved by ge in camouflagepattern to match existing surface complete all as specified and directed. 47 m&l in repairs precast cement concrete louvres and jallies, 40 mm thick ( measured solid ) , including all mouldings but excluding frame, type b 0 ( 1:2:4 ) using 12.5 mm graded stone aggregate, set in cement mortar 1:4, complete all as specified and directed. 48 m&l as in repairs precast cement concrete post, ornamental moulded, 75mm x 75mm in section, total length of each post exceeding 45cm but not exceeding 60cm, type b 0 ( 1:2:4 ) using 12.5 mm graded stone aggregate, with groves on two opposite sides for holding jalli 40mm thick, set in cement mortar 1:6, complete all as specified and directed. 49 m&l for ms work in roof trusses ( framed ) , trussed, purlins, crane gantries, rails, posts andfastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc.including special shaped washer etc. complete and including all necessary drilling or cutting holes in brick / concrete surfaces and making good, welding work, bolting or reveting etc and similar work conforming to fe 290 gde e 165 complete and all as specified 50 s&f 6 mm thick asbestos cement corrugated sheet in roof, fixed with j or l hook or cranked bolt with washers. 51 re fixing only 6 mm thick asbestos cement corrugated sheet in roof, fixed with j or l hook or cranked bolt with washers in small areas. 52 s&f asbestos cement two piece adjustable plain wing ridge 6mm thick, fixed in repairs with j or l hook or cranked bolt with washers. 53 supply and fixing0.63mm thick galvanized, corrugated mild steel sheeting with grade of zinc coating 275 as in roof covering in patches with two corugation side lap, l or j type hooks and washer or fixed with self thread making steel screws with suitable arrangement as required, as in roof, complete all as specified & directed. 54 supply and fixing0.63mm thick galvanized with grade of zinc coating 275 plain mild steel sheeting as in roof covering / cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape as required and directed at site fixed with l or j type hooks an washer or fixed with self thread making steel screws with suitable arrangement as required, complete all as specified & directed. 55 m & l for pre painted galvalume aluminum zinc coating gi based corrugatedor semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified. 56 m / l for pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified. 57 s&f in reapirs ceiling board of arm gyp fb ceiling snow frost vinyl face, washable metallized polyster foil backing, vinyl covered edges, suspended ceiling on suspension system. panels shall be of size 600 mm x 600 mm x 9 mm, having 7kg / sqm including restraining of supporting hangers and necessary nothcing and prepared to holes for re securing ofgi frame workcomplete all as specified and directed.make : amstrong, gyptech, dexune 58 s&f in repairs ceiling snow frost vinyl face, washable metallized polyester foil backing , vinyl covered edges, suspended ceiling on suspension system. panels shall be of size 600 mm x 600 mm x 9 mm, having 7 kg / sqm, including providing grid system for fixing ceiling tiles shall comprise of suspension system with true horizontal level, suspended on inter locking tegular “select” system with 15mm black flanges incorporating a 4mm central reveal in black colour and a load carrying capacity of minimum 14.50 kg / m2 with birdsmouth notches metal grid of hot dipped galvanized steel sections consisting of main t runner with suitably spaced joints to get required length and of size 15x32 mm made from 0.30 mm thick ( minimum ) sheet, spaced at 1200 mm center to center and cross t of size 15mmx25mm made of 0.30 mm thick ( minimum ) sheet, 1200mm long spaced between main t at 600 mm center to center to form a grid of 1200mmx600 mm and secondary cross t of length 600 mm and size 15mmx25mm made of 0.30 m thick ( minimum ) sheet to be interlocked at middle of the 1200mmx600 mm panel to form grids of 600mmx600mm and wall angle of size 20mmx15mmx0.3 mm and laying false ceiling tiles of approved texture in the grid including, required fitting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main t runners to be suspended from ceiling using gi slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm gi adjustable rods with galvanised butterfly level clips of size 85mm x 30mm x 0.8 mm spaced at 1200 mm center to center along main t, bottom exposed width of 15 mm of all t sections all complete for all heights as per specifications, drawings incl dismantling of old ceiling, all as specified and directed. 59 repair to de railed sliding steel gate, over allsize24.80m x 8.40mhaving 06 leafs ofsize 4.10 m x 8.2 m each, for smooth functioningof gate by welding where required, dismantling, staightning and refixing in position damaged steel members, cutting and levelling bottom unlevelled pcc stucking to steel members to steel rollers tightening / replacing of worn out nuts & bolts, welding and re adjusting / replacing top / bottom steel rollers, greasing to all movable parts complete all as specified and as directed.note : ( i ) t&p and grease required for taking down the door for repair and re fixing the same shall be arranged by the contractor at his own and the unit rate quoted shall include the cost thereof. no clam whatsoever on this account shall be entertained. ( ii ) replacement of defective steel members, items shall be measured and paid as supply only against respectiveitem of this schedule. 60 all as per item no. 59 here in before but over all size of gate 16.0m x 6.0 mtr having 04 leafs of size 4.0 m x 6.0 m each. 61 repairing of rolling shutter, push type, size n.exc 6sqm eachfor smooth functioning by re posting of laths, riveting to old defective rivets, tighteningnuts and bolts, re stretching of spring, greasing to movable parts and at guide channel including taking out and re fixing rolling shutter in position complete all as specified and directed.note : ( i ) t&p required for taking down the door for repair and re fixing the same shall be arranged by the contractor at his own and the unit rate quoted shall include the cost thereof. no clam whatsoever on this account shall be entertained. ( ii ) replacement of defective steel members, items shall be measured and paid as supply only against respectiveitem of this schedule. 62 all as per item no 61 above but size of rolling shutter exc 6sqm but n.exc 15 sqm. 63 supply only mild steel plain sheet 1.00mm covering to door shutter and top cover of rolling shutter cover cut to size, edges beaded as directed, holes punched all as specified and directed. 64 supply only ms spring suitable for rolling shutter complete all as specified and directed. 65 supply only ms ball bearing suitable for rolling shutter complete all as specified and directed. 66 supply only mild steel section of any size or any section for guide channel of rolling shutters including necessary cutting & drilling holes as required and making good all as specified and directed. 67 s&f as in repairs rolling shutter gear operated type with bevel gear box and crank handle with 1.25 mm thick lath without ball bearing as specified including top cover anchoring rod, hasp and staple, side guide rail etc and erected in position built as indicated, including cutting holes in brick / rcc walls and making good complete all as specified and directed 68 s&f solid pvc wall lining consisting of 5mm thick wood grain printed pvc sheet inclusive of solvent cement and fixing at site on pvc frame as per specifications and drawing including dismantling of sheets complete all as specified . 69 m&l5mm thick pvc sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make pvc frame as per specification and drawing. 70 supply and fixing as in repairs anti bird net, square mesh size 20 mm x 20mm, black / white hdpe knotted net, thickness of the net 1.00mm, weatherproof, u.v. stabilized and chemically inert, breaking strength of 23.08 kg per yarn, having a melting point of 260°c fixed with boarder rope of dia 4mm, uv stabilized boarder rope jointed with the net by machine inter locking process using three twinces of the same as that of nettied to12mm dia hooks ( made to shape ) orwelded to steel structure and 12 mm dia ancher fastner bolt fixed to rcc structure as applicable at suitable intervalscomplete all as specified and directed. 71 taking down aluminium shutter / sliding door for necessary repair work and re fixing in position after necessary repair work such as setting of floor spring, pivot adjusting etc incl necessary fixing of screwsetc for proper function of aluminum door of sizen exc 1.5 sqmeach complete all as specified and directed.note : replacement of defective items shall be measured and paid as supply only against respectiveitem of this schedule. 72 supply only double action floor door spring hydraulically regulated made up minimum1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified 73 supply only top pivot of casting body suitable for aluminum door complete all as specified and directed 74 s&f in repairs 4.80 mm thick sheet glass ofordinary quality plain / tintedand glazing with rubber beads, clips etc complete all as specified and directed.note: cost of rubber beads, clip included in unit quoted rate of this item. 75 s & f as in repairs mild steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed. 76 s & f as in repairs aluminium grill of size, 85mm x 85mm hexagonal shaped mesh, fixed to aluminium frame work with u clip of size 15mmx12mm & fastners complete all as specified and directed. 77 supply and fixingin repairs powder coated aluminium ( minimum thickness of powder coating 50micron ) work for frames of doors, windows, ventilators and partitions ( fixedportions ) with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directionsof engineer in charge 78 providing and fixing in repairs powder coated aluminium ( minimum thickness of powder coating 50 micron ) work for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) with extruded built up standardtubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, rollers & dust proof brush for sliding door / windowcomplete all as per architectural drawings and the directions of engineer in charge. 79 s & f double action floor door spring hydraulically regulated made up minimum1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified 80 s & f top pivot of casting body suitable for aluminum door complete all as specified and directed 81 supply and fixing 170 to 200 mm size extruded aluminiumalloy handels fabricated fancy type, anodised fixed with stainless steel screws complete all as specified and directed. 82 supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section, fixed with stainless steel screws complete all as specified and directed. 83 s & f4.80 mm thick sheet glass ofordinary quality plain / tintedand glazing with rubber beads, clips etc complete all as specified and directed. 84 supply and fixing only 3 mm thickhigh quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed. 85 s & f steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed. 86 taking down & seiving the existing sand and saw dust mix laid along the slant height upto a height of 15 metre from gl, re filling the sand and saw dust mix passed through seives in position complete all as specified and directed.note: ( i ) mix of sand and saw dust before seiving shall be brought down and stacked properly. stack shall be measured and recordedfor payment purpose. ( ii ) supply and mixing of sand and saw dust shall be measured and paid for separately under respective item of this schedule. 87 labour only for mixing coarse sand and saw dust manually in proportions as directed by ge and filling where directed upto a height of 15 metre from gl complete all as specified and directed.note: sand and saw dust shall be measured and paid separately as supply only under respective item of ths schedule. 88 supply only coarse sand complete all as specified and directed.note: measurement shall be taken from the stacked material and 10% shall be deducted on account of voids. 89 supply only saw dust complete all as specified and directed.note: measurement shall be taken from the stacked material and 30% shall be deducted on account of voids. 90 taking down chowkats or frames but with shutters ( with outtaking off shutter from the frames ) not exc 1.5 sqm eachcomplete all as specified and directed. 91 taking down chowkats or frames but with shutters ( with outtaking off shutter from the frames ) exc 1.5 sqm but n. exc 4 sqmeachcomplete all as specified and directed. 92 taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed. 93 supplying & fixing 1.25 mm thick pressed steel door frames size 105x60mmfor doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c 0 ( using 12.5 mm graded stone aggregate complete all as specified. ) 94 supplying & fixing 1.25 mm thick pressed steel door frames size 125x60mmfor double doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with pcc 1:3:6 type c 0 using 12.5 mm graded stone aggregate complete all as specified. 95 supplying & fixing solid pvc door frames of sizes 50mm x 47mm made out of 5mm single side prelam pvcsheet used instead of plain colour pvc sheet & edges will be painted to match with prelam sheet reinforced with ms square tube complete all specified and as directed. 96 s & f factory made solid panel pvc door shutter 30mm thick ( style ) consisting of frame made out of m.s. tubes for top and bottom rails. m.s. frame shall be covered with heat moulded prelam pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and prelamcolour pvc sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam pvc sheet used insted of plain colour pvc sheet. stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the ms framewelded, sealed to the stiles and rails with suitable pvc sheet beading , and jointed together with solvent cement complete all as specified in ssr part ii. 97 s&f factory made 30mm thick flush shutters, solid core construction, with particle board coreand plywood face panels, commercial type on both sides includeforthe provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specified and directed. 98 m& l for providing cupboard shutter in required size at site made out of18 mm thick pvc colour sheet and provision of shutters one side decorative pre laminated pvc sheetand all required brackets ss screws etc. the pannels shall be fabricated using adhesive and screws where required. all the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per draeing and specification approved by engr in charge. 99 s & f factory made glazed & skeleton shutters 35mm thick open rebated & prepare to received glass, gauge etc edges of framing plain chamfered or rounded inwindow, ventilator etc are provided with stiles and rails in 2nd class hard wood all as specified in ssrpart i, section 8 clause 8.20 ( b ) . 100 s&f 35 mm thick 2nd class hardwood, plain, framed, panelled shutters ( any number of panels ) , in with panels of timber flat on both sides ( feather edged ) , of 12 mm bwp commercial ply with commercial veneering on both faces; supplied and fitted to chowkats 101 s&f factory made box type steel window 1.25mm thickerw hollow p section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage andglass shutter comprised gaused glazed &skelton shuttererw section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of t section 20mmx3mm complete welded to frame with one vertical mullion of erw box type t section of size 60mmx25mm and 1.25mm thickwith following fittings welded to the frame shutter : i ) hold fast 150mm long mild steel flat iron 12x3 mm made to shape 04 nos per window. ii ) handle of z section 20mmx25mm, 100mm long – 01 no per leaf.iii ) ms tower bolt 150mm long 2 no per leaf. iv ) z section 20mmx25mm, 100mm long stopper – 01 nos per leaf. v ) cleat 55 mm long of solid square 15x20x.63mm square 01 nos per leaf vi ) ms pintal hinges 12 x 75 mm 2 nos each leaf vii ) 10 mm squre guard bar @ 10 cm c / c viii ) 25 x 3 mm flat iron for joint of both frame wiremesh & glazed welded inner side and outer side of frame ( ix ) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed / gazed skelton shutterof window ( x ) 3mm thick sheet glass ordinary quality and with oil putty in squre n exc 0.50 sqm in each pane fixed in glazed / guage skelton shutter of windowxi ) fabrication and fixing arrangements as per specificationincluding taking down, cutting holes and making good dismantled portion in pcc 1:2:4 type b 1 / cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.note: ( i ) windows shall be povided as per the td of chief engineer chandigarh zone, td 219 i.e typical details of box window ( steel ) with fly proof shutter. ( ii ) the mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account. 102 s & f mild steel box type ventilator fixed type with glazing bar with mesh & glass all as per item ser no 101 above 103 m & l for wooden surfaces of any description not other describe over 10cm width or girth and applying twocoat of synthetic enamel paintover one coat of pink primer, including preparation surface. 104 m & l for steel surfaces of any description not other describe ver 10cm width or girth and applying twocoat of synthetic enamel paintover one coat of red oxide, including preparation of surface. 105 taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkat and re fixing in same opeing after re securing or easening and adjusting including repaircomplete all as specified. 106 supply and fixing aluminium butt hinges medium weight, cold rolled, 100mm, isi marked, fixed with stainless steel screws complete all as specified and directed. 107 supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section, fixed with stainless steel screws complete all as specified and directed. 108 supply and fixing 150 mm size extruded aluminium aluminium alloy handels fabricated type, anodised fixed with stainless steel screws complete all as specified and directed. 109 supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple ( bolt type ) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed. 110 s&f ball magnetic catcher with 8mm dia steel ball, brass body and striking plate fixed with brass screws or with adhesive complete all as specified and directed. 111 supply and fixingin stainless steel wirecloths 0.45 mm nominal dia of wire and average width aperature1.40mm and fixed with stainless wire staples complete all as specified and directed.. 112 all as item no. 111.00 above but as in repairs. 113 supply and fixing in repair 140mm long floor door stoper of aluminium alloybody and toungue, anodised wirh hard drawn steel spring, fixed to door shutter fixed with stainless steel screws complete all as specified and directed. 114 hacking out old broken glass ( any thickness size quality or description ) from wooden frames or stone, concrete or brick surrounds glazing with putty or fixed with beads and s&f 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each panes complete all as specified and directed. 115 supply and fix in repairs heavy duty stainless steel ( grade 305 ) curtain rods 25mm dia complete all as specified and as directed. 116 supply and fix in repairs stainless steel ( grade 305 ) brackets with finnals ( open ends ) suitable for curtain rods of25mm dia complete all as specified and as directed. 117 supply and fix in repairs stainless steel ( grade 305 ) brackets ( dead ends ) suitable for curtain rods of25mm dia complete all as specified and as directed. 118 taking up or down 15 mm dia steel tubing & connections including fittings complete all as specified and as directed. 119 all as per d item no.118.00 above but 20mm bore tubes. 120 s & f 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed. 121 all as per description of serial item no. 120.00 here in before but 20mm bore tubes. 122 dismantling water tanks any type of capacityexc 250 but n.exc 500 liters 123 s&f 500 liter capacity rotational moulded polyethylene water storage tanks ( cylin drical vertical with closed top ) tripple layered white, hoisted and fixed in position, including 20 mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. 124 s&f 20mm ptmt nipple suitable for hdpe water tank ( minimum weight 45gms ) complete all as specified . 125 s&f in repairpvc ( ptmt ) float valve, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all assecified and directed 126 s & f in repair long body stop valve 15mm borefancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions. 127 s&f in repair 15mm bore long body angle cock fancy type chromium plated screwed down high pressureclomplete all as speified 128 s & f in repair long body stop valve15mm borefancy type chromium plated with long shank and cup ( concealed type ) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed. 129 s&f in repair 15mm long body bib taps long shankcast copper alloy with crutch or butterfly hadle secrwed for iron piper or for brass ferrule complete all as specified and as directed. 130 s&f in repair pillar taps long body fancy type with capasten head chromium plated screwed down high pressure with without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. 131 s&f in repairs 15mm bore pvc connection pipe 450mm long with ptmt nuts at both ends complete all as specified and as directed. 132 s &f in repair chromium pated shower rose 125mm size with or without swivel joints, any size including fixing to 15 mm bore steel pipe or union complete all as specified and as directed. 133 s & f in repair towel rail 20mm dia chromium plated including 600mm longincluding brackets, screws and wooden / plastic cleats complete all as specified and as directed. 134 s&f in repairs 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac plain building board or commercial ply wood and fixed to wooden plug with chromium plated brass screw and cup washers complete as directed. 135 s&f in repairs 100 mm dia stainless steel gratingcomplete all as specified. 136 s&f in repairs 75 mm dia stainless steel with hole grating complete all as specified. 137 s&f in repairswaste down pipe 32 / 40mm bore for wash basin / sink complete all as specified and directed 138 s&f in repairs vitreous china wash down water closet pan pedestal pattern ( type white including pvc seat cover , connection to waste pipe and flushing pipe completemake hindustan / cera / neycer 139 s&f as in repairs vitreous chinawc, rimless, single piece, 360mmx675mmx750mmsize, with uf soft close seat cover, hinges, fixing accessories and cistern fittingsincluding 300 mm s trap, chrome finished brass jet spray with connection lead, complete all as specified .make : jaquar cat part no ops wht 15851 sn or equivalent cera, parryware 140 s&f as in repairs health faucet with 1.5mm flexible chromium plated tube and hook fixed to angle valve etc complete all as specified and directed.make jaquar cat part no. ald 573 or equivalent cera, parryware 141 s & f in repair 10 ltr capacity pvc valveless syphonic action type flushing cistern low level white with inlet ball valve and brackets, float and handle, l bend complete all as specified and directed 142 s&f in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed 143 s & fvitreous china half stall urinal white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, fixing automatic flushing cistern with brackets and pointing around urinal back in cement, fixed in repairs complete all as specified and directed. 144 s&f as in repairs corner glass shelfcomplete all as specified and directed.make : jaquar cat part no aqn 7771 or equivalent. 145 s&f as in repairs toilet paper holder, chromoim plated without flapcomplete all as specified and directed. make : jaquar cat part no ahs 1553or equivalent. 146 demolition up to100 / 75mm bore and breaking up drain pipes ( ac / reinforced concrete / salt glazed ) complete all as specified and directed 147 s & f 110mm bore pvc swr pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed 148 s & f 75mm bore pvc swr pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed 149 s & f 110mm bore pvcswr junction single ( single t ) equal or unequal complete all as specified and directed 150 s&f pvc ( swr ) bends of 110 mm bore complete all as specified and directed 151 s&f pvc ( swr ) bends of 110 mm bore with access door complete all as specified and directed 152 s&f pvc ( swr ) bends of 75 mm bore complete all as specified and directed 153 s&f pvc ( swr ) bends of 75 mm borewith access door complete all as specified and directed 154 s&f pvc ( swr ) bends of 110 mm reducers complete all as specified and directed 155 s&f pvc ( swr ) bends of 75 vent cowlwith access door complete all as specified and directed 156 s & f in repair75mm bore pvc ( swr ) floor trap, with grating plain / whole including jointing to waste pipe fixed in cement concrete type b 1 ( 1:2:4 ) complete all as specified and directed....

Due Date : June 04, 2022

Tender Value : ₹ 39.96 Lakhs

View Tender
45
Military Engineer Services - Rajasthan

31963069 repair / maintenance of dg set and other connected items , repair / maint ofexternal electric works, steet lightsand lt ug cables at west camp, south camp and dbs& motigarh, pugal , rd 498 ascon nodes andrepair / maint of summer appliances , deep freezer, water cooler & acat age mffr under ge ( n ) bikaner taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified.note : work will be carried out upto 4th storey of bldgs also as per pirection of engr in charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account. 2 rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement ( up to 4th storey with necessary scaffolding ) complete all as specified and as directed by engineer in charge. 3 m&l rendering cement plaster, 15 mm thick on fair faces of brick / concrete surfacesof wall in cement mortar 1:6 finished even and smooth w / o using extra cement complete all as specified. 4 rendering 10 mm thick on fair faces of brick or concrete surfaceceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cementcomplete all as specified and as directed by engineer in charge. 5 preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washingcomplete all as specified and as directed by engineer in charge. 6 preparation of new plastered or unplastered surfaces of walls to achieve smooth and even surface and applying three coats of white washingcomplete all as specified and as directed by engineer in charge. 7 material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified. 8 preparationof newplastered / concrete surfaces of walls to achieve smooth and even surfaceandapplying two coats of cement based paint over and includingone coat of primer ( up to 4th storey with necessary / scaffolding ) complete all asspecified andasdirected by engr in charge. 9 supply and fixing in repair brass face for cp / brass bib tap, angle / stop cock, pillar cock, wall mixer, whb mixer, etcfor 15 mm bore pipecomplete all as specified and as directed by engineer in charge. 10 supply and fixing in repair, pvc knob or flushing handle for flushing cistern of capacity 10.0 litres , complete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) 11 supply and fixing in repair, pvc float valve suitable for flushing cistern of capacity 10.0 litrescomplete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) . 12 supply and fixing in repair, pvc syphonic kit for flushing cistern of capacity 10.0 litres, complete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) 13 supply and fixing in repair, pvc bend suitable for flushing cistern of capacity 10.0 litres, complete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) . 14 supply and fixing in repair, pvc syphon washer suitable for flushing cistern of capacity 10.0 litrescomplete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) 15 repairs to steel window, ventilators of any size to make it functional ( including slot pin, hinge, hook and eye of standard quality where required ) , resecuring of windows wire gauge and railings / grills by using welding equipments, complete all as directed. 16 repair / easing ofwooden door any type, glazed or panelled, by trimming the side of door shutter where rubbing with chowkhat, unscrew the hinges screws and lift the door and fix with screws, tightening of wire mesh etc all as per engr in charge. 17 material and labour for ( a ) repairing aluminium shutters ( door / window ) including refixing, tighteningand making good with usingrubber / beads and others small fixtures / fittings if required and making serviceable all as specified and directed by engr in charge. 18 ( b ) aluminium door locks ( sample approved by engr in charge ) 19 taking down shutters of any description n.exc 1.00 sqmeach and removing from the site all as specified & directed. 20 taking down shutters of any description exc 1.00 sqm and n.exc. 2.00 sqm each and removing from the site all as specified & directed. 21 taking down chowkats or frames with shutter ( without taking off shutter from the frame ) n.exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from siteall as specified. 22 taking down chowkats or frames with shutter ( without taking off shutter from the frame ) exc 1.5 sqm&n.exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick workand removing from site all as specified. 23 s&f pressed steel framesof size 125mm x 60mm made outof size 1.25mm thick ms sheet for doorssingle rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type b 1 including pcc 1:3:6 as in back fill to chowkats all as specified. 24 s&f pressed steel framesof size 105mm x 60mm made outof size 1.25mm thick ms sheet for doorsdouble rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type b 1 including pcc 1:3:6 as in back fill to chowkats all as specified. 25 supply and fixing factory made, plain framed, panelled shutter ( two panel ) 35mm thick, 2nd class hardwood with lock rail and panel of 9 mm b.w.p commercial ply. the size of rail and stiles as per as per is:1003 ( part i ) , kiln seasoned and chemically pressure treated complete all as directed by engr in charge. 26 supply and fixing 35mm thick2nd class hard wood glazed, gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitredand rebatedsash bars, stiles and rails as specified in ssr part i sec 8 clause 8.24 ( a ) complete all as specified 27 s&f flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.note : sampel approved by engr in charge or ge. 28 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all asspecified and as directed by engr in charge. 29 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppplyingand fixing in the frame at site as per specification & drawing complete all asspecified and as directed by engr in charge. 30 s&f factory made solid pvc moulded door shutter 28 to 30 mm thick ( stiles ) with particle board core with 2, 4 , or 6 raised panel design with 2 mm thick mouldedprelam pvc sheet on the front face & 2 mmprelam pvc sheet on back face, to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable pvc sheet beading, and joined together with solvent cement, supplying and fixing in the framme at site as per specification and drawing, complete all asspecified and as directed by engr in charge. 31 taking down of old / unserviceable kitchen cabinet / cupboard including all fixture and fitting, complete all as specified and directed.note: for measurement superficial area in elevation shall be measured. 32 s&f factory made 18mm ( +0.7mm ) thick celuka pvc ply of density 600kg / cbm manufacured by an iso 900 2008 certified company. one side prelam and other side plain18mm thick celuka pvc ply for kitchen cabinet shutter and also manufactuers test report and test certificate is mandatory with each and every supply of the material complete as per manufacturers specifications and drawing and as directed. 33 s&f factory made 18mm ( +0.7mm ) thick celuka pvc ply of density 600kg / cbm manufacured by an iso 900 2008 certified company. plain 18mm thick celuka pvc ply for shelf / partitions / drawer and also manufacturers test report and test certificate is mandatory with each and every supply of the material complete as permanufacturers specifications and drawing and as directed. 34 s&f factory made 5mm thick pvc of density 600kg / cbm manufacured by an iso 900 2008 certified company. plain 5mm thick pvc sheet paneling for back side ( wall side ) and also manufacurers test report and test certificate is mandotary with each and every supply of the material complete as per manufacturers specifications and drawing and as directed. 35 s&f 100mm size stainless steel handle complete all as specified and as directed. 36 s&f ball rolling sliding channels of size 450mm length fixed in cupboards with screws as in drawers 37 s&fauto hingesof size 150mm length fixed in cupboards with screws for holding stainless steel baskets as in drawers 38 s&f self adhesive tape of 18 / 19mm width , hot pressed & pasted on sides & bottom of edges of cupboards shutters 39 s&f steel fasteners of size 75mm long drilled and fixed to walls 40 s&f 50mm dia and 75mm long steel supports fixed with bolt at bottom of cupboards box all as specified 41 pressed steel cup board frameof ms sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including pcc 1:2:4 as in filling to back of chowkats includingbutt hinges 100 mm long. piano hinges measured separately. 42 prelaminated mdf board 19 mm thick as in shutters / shelves ( exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame worknincluding lipping ( 15 mm thick three sides and 20 mm thick lipping hinge side ) around the shutter complete all asspecified and as directed by engr in charge. 43 s&f in repair continuous ( piano ) hinges, width of flaps ( when open ) 30 mmheavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified. ( isi marked ) 44 s&f butt hinges of mild steel cold rolled medium weight of size 100mm as specified. 45 supply and fixingfor stainless steel medium weight butt hinges, 100mm , complete all as specified and as directed 46 s&f aluminium anodised, barrel tower boltssize 150 mm of extruded section and fixed complete all as specified. ( isi marked ) 47 s&f aluminium handles, fabricated type, anodised size 100mm, anodised section and fixed complete all as specified. ( isi marked ) 48 s&f aluminium alloy, anodised, sliding door bolt size 250 mmwith hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified. 49 s & f hasp & staple safety type aluminium anodised with mild steel hinges spin including bolt to hinges plate fixed with screws of 75 mm in length. 50 s&f aluminium hanging floor door stopper, twin rubber stopper, size 100mm , anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. 51 m&l for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed. 52 s&f 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified. ( isi marked ) 53 s&f in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified. 54 supply and fixing in repair mild steelhelical ordinaryrat tail rod patternsprings300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed. 55 s&f in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 rm length, with stainless steel brackets near to ends with stainless steel finialsfor 25mm dia drapery rod at both ends. the drapery rod shall be projecting 150 mm outer side from the clear opening of doors / windows. ( including necessary fittings ) 56 s&f powder coated aluminium door shutter including frame of hollow section 101mm x 44.00mm xthickness not less than 1.53 mm including aluminium anodized powder coated of hollow section glazed shutter of stiles size 85mm x 44.45mm xthickness not less than 1.56mm having grooves for aluminium beading and top rail of hollow section 83.5mm x 44.45mmxthickness not less than 1.50mm, lock rail of hollow section 83.5mm x 44.45mm xthickness not less than 1.50mm and bottom rail of hollow section 114.3mm x 44.45mmx thickness not less than 1.50mm , one derived handle 300mm long, 100mm long butt hinges or aluminium floor type hydraullic door closer, aluminium mortice lock 65mm 4 levers of godrej make and glazing with select quality tinted glass 5mm thick or panelling with acp sheet and cleat rubber packing aluminium beading including aluminium hardware fitting complete all as specified and as directed by engr in charge and approved by ge. 57 m&l aluminum power coated, sliding windows three track with mosquito proofing with style 44.4x44.5x2mm thick including 4 mm thick coloured / tinted / frosted glass panes including all necessary fittings and fixturescomplete. 58 m&l for anodised aluminium grills, 6mm dia size 100x100mmfixed to aluminium windowsand thickness of powder coating not less than 50 micron, complete all as specified. 59 taking down wall panelling including any type of aluminium door, windows and partition in any position complete all as specified and as directed by engr in charge. 60 s&f in repair aluminium extruded section body, door closer hydraulically regulated, designation no. 1, universal type, suitable for door shutters of 700mm in width and of weightnot more than 35kg and fixed. 61 supply and fixing in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. 62 s&f in repair brass mortice lock with brass handles and fittings , 4 leververtical type, size 100 mm including complete accessories complete all as specified. make: links locks / godrej / harrison 63 supply and fixing5 mm thicksheet glass ordinary quality coloured / tintedand glazed in squares, n.exceeding 0.5 sqm in each pane. 64 supply and fixing5mm thick ( minimum ) glass sheet selected quality coloured / tinted / frosted and glazed in squares, n.exceeding 0.5 sqm in each pane. 65 supply and fixing 4mm thick aluminium composite panel ( coloured sheet ) and in additional other accessories for fitting complete all as specified by engr in charge. 66 material & labourfactory made steel windows double shutter box type, outer frame made out of erw tube p section ( 60x45x25mm ) and shutters of erw tube p section ( 50x35x20mm ) operable shutters side hung includding pistol hinges with two nos of ms tower bolts 150mm size on each shutter steel handle and stopper of z section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings / openning for cooler / ac where required .steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per drg no cepz / td 324 / 07 1 / 3 to 3 / 3 all as specified and directed by engr in charge.note: the quoted rate against the above item shall also include ( i ) 04 nos ms steel lugs of 20x5mm ms flat 20cm long over all welded to frames ( ii ) pcc block for embedding lugs. 67 ditto all as per item no 66 but in ventilators any size. 68 s&f framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work conforming to fe.290.gde e 165 69 hacking out old broken glass ( any thickness, size quality or description ) from any types of wooden / steel / alum ( up to 4th storey ) frames or stone concrete or brick surrounds glazed with putty or fixed with beads. 70 s&f4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 sq each pane in any type of frame of iron / steel / wood / aluminium as required at site complete all as specified ( uptofourth storey with necessary scaffolding ) , all as specified. 71 s&f 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 sq each pane in any type of frame of iron / steel / wood / aluminium as required at site complete all as specified ( uptofourth storey with necessary scaffolding ) , all as specified. 72 securing glass of any description in existing wooden and iron frames glazed with putty / beads including removing loose or decayed putty / beads, painting / oiling one coat on rebates, grooves, reputtying and painting / oiling puttied surface to match existing work ( new length of frame reputtied shall be measured. 73 supply and fixing stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple 74 supply and fixing galvanised mildsteelwire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specifiedfixed with stainless steel wire staples. 75 supply and fixingin repair galvanised mildsteelwire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specifiedfixed with stainless steel wire staples. 76 s&f in repair central hole basin mixer without popup waste system with 450mm long braided hoses also available all as per directed and specified.make : jaquar, cat no cqt 23167b or equivalent in cera / hindware 77 supply and fixing in repairwall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified make :jaquar, cat no cqt 23219or equivalent in cera / hindware. 78 s&f in repairwall mixer 3 in 1 system with provision for both hand shower & overhead shower complete with 115mm long bend pipe on upper side, connecting legs & flanges ( without hand & overhead shower ) complete all as specified. make: jaquar, cat no: cqt 23281upr or equivalent in cera / hindware. 79 s&f in repair hand shower 120mmdia round shape multi flow with cascade effect ( abs body chrome plated with gray face plate ) with rubit cleaning systemcomplete all as specified. make : jaquar, cat no hsh1731 or equivalent in cera / hindware. 80 s&f in repairsink mixer with swinging spout ( wall mounted model ) with connecting legs & wall flanges complete all as specified. make: jaquar, cat no cqt 23309 or equivalent in cera / hindware. 81 s&f in repair sink cock with swinging casted spout ( wall mounted model ) with wall flange complete all as specified make: jaquar, cat no cqt 23347 or equivalent in cera / hindware 82 s&f in repair bib cock with wall flange cast copper alloy, chromium plated fancy type , complete all as specified. make : jaquar, cat no: sqt 23047 or equivalent in cera / hindware. 83 s&f in repair 2 way cp bib cock with wall flange, cast copper alloy, chromium plated fancy type, sutable for 15 mm gi pipe, complete all as specified. make : jaquar, catno: cqt 23041 or equivalent in cera / hindware. 84 s&fin repair angle cock with wall flange , cast copper alloy, chromium plated fancy type screwedfor 15 mm iron pipe, complete all as specified. make: jaquar, cat no cqt 23059 or equivalent in cera / hindware 85 s&fin repairexposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange ( compatible with ald 069 ) complete all as specified. make: jaquar, cat no: cqt 23069k or equivalent in kohler / artize. 86 s&f in repair 15mm bore cp bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified. make: jainko, essco, parko, prayag 87 s&fin repair 15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwedfor 15 mm iron pipe, complete all as specified. make: jainko, essco, parko, prayag 88 s&fin repair 15mm borestop valves, cast copper alloy, fancy type, chromium plated with long shankandcup ( concealed type ) screweddown, highpressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed, complete all as specified. make: jainko, essco, parko, prayag 89 s&f in repair 15mm bore cp pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified. make: jainko, essco, parko, prayag 90 supply and fixing in repair health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect as specified.make: jainko, essco, parko, prayag 91 s&f in repair tubular towel rail, 20mm dia, d type, 60cm long between flangescomplete all as specified. make: jainko, essco, parko, prayag 92 s&f in repair chromium plated, towel ring, complete all as specified. make: jainko, essco, parko, prayag 93 s&f in repair chromium plated towel rack 600mm long without lower hangers, stainless steel complete all as specified. make : jaquar cat no akp 35781pfs or equivalent in cera / hindware. 94 s&f in repairstainless steel shop dishholder complete all as specified. make: jainko, essco, parko, prayag 95 s&f in repair toilet paper holder with flat recessed type stainless steel complete all as specified and directed., complete all as specified. make : jainko, essco, parko, prayag 96 s&f in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long . complete all as specified. make : jainko, essco, parko, prayag 97 s&f in repair corner glass shelf ( with bracket ) as per directed by engr in charge. make: jainko, essco, parko, prayag 98 s&f in repair waste coupling of chromium plated brass32 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basinall as specified . make : jainko, essco, parko, prayag 99 s&f in repair waste coupling of chromium plated brass40 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basinall as specified . make : jainko, essco, parko, prayag. 100 s&f in repair pvc connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.make : jainko, essco, parko, prayag 101 s&f in repair pvc connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore. make : jainko, essco, parko, prayag 102 s&f in repairbrasschromiumplatedshower rosewith or without swivel joints, 125mm size, including fixing to steel pipe or unionmake : jainko, essco, parko, prayag 103 s&f in repair single piece wc with uf soft close seat cover, hinges, fixing accessories set and accessories set, cistern fittings, size: 660 x 365 x 765mm, s trap 300mm complete all as specified. make : cera, cat no s1013105 or equivalent in hindware / jaquar. 104 s&f in repair under counter basin white colour with fixing accessories set, size: 560 x 470x190, oval shape, including cpwaste coupling and pvc waste pipe complete all as specified. make : cera, cat no s2030104 or equivalent in jaquar / hindware. 105 s&f in repairvitreous china, wash basin white, flat back , size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass.complete all as specified and as directed by engineer in charge.. make : cera, cat no s2040119 or equivalent in jaquar / hindware. 106 s&f in repair full pedestal for whbcomplete all as specified. make : cera, cat no s2090113 or equivalent in jaquar / hindware. 107 s&f in repair pvc valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, pvc 32 mm l bend of capacity 10.0 litres and making good to dismantled / damaged floor / surfaces, fixing in repair, complete all as specified and as directed by engineer in charge. make: cera, cat no b1010109 ( congo ) or equivalent in jaquar / hindware. 108 supply and fixing in repairpvc seat cover for ewc pan ( white ) of standardd quality including hinges bolt etc all as directed by engr in carge.make: cera cat no b1510121 or equivalent in jaquar / hindware. 109 supply and fixing in repair vitreous china ware pedestal type water closet white, with p or s trap including self closing seat cover, closed pattern with flat bottom, complete all as directed. make: cera, cat part no s1053101 or equivalent in jaquar / hindware. 110 s&f in repair wc orissa pattern white with integral foot rest580x 440 mm including l bend, &pcc bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified. ( rate of including in taking out and removal of old wc seat unhygienic condition ) make: cera, cat part no s3010102 ( calina ) or equivalent in jaquar / hindware. 111 supply and fixingin repair pvc waste pipe 32mm bore of required length complete. make: prayag cat no 329 or equivalent in polytuf / jindal. 112 supply and fixing in repair pvc waste pipe 40mm bore of required lengthcomplete for sink / whb . make: prayag cat no 330or equivalent in polytuf / jindal. 113 dismantling water tanks and removing to store of water storage tanks ( cap. 500 ltr to 1000 ltr ) complete all as specified and directed by engineer in charge. 114 dismantling water tanks and removing to store of water storage tanks ( cap. 250 ltr to 500 ltr ) complete all as specified and directed by engineer in charge. 115 supply and fixingrotational moulded polyethylene water storage tanks of1000 litres capacity, ( cylindrical vertical with closed top ) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in ssr part i including ptmt ball valves high pressure with epoxy coated aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified. make : vectus, sintex, sheetal. 116 supply and fixingrotational moulded polyethylene water storage tanks of 500 litres capacity, ( cylindrical vertical with closed top ) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in ssr part i including ptmt ball valves high pressure with epoxy coated aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specifiedmake : vectus, sintex, sheetal. 117 disconnecting of water tank of 500 ltr capacity setting aside ( or lowering if required ) for repairs, cleaning etc. and hoisting if required reconnecting and re fixing in position. ( cleaning repairing, etc. measured separately ) . 118 cleaning and removing all scale and dirt etc, from exc 250 & n exc 500 litres capacitytanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed. 119 cleaning and removing all scale and dirt etc, from exc 500 & n exc 1000 litres capacitytanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed. 120 supply and fixing in repair gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 25 mm bore pipe, including making connections complete all as specified and fixed. 121 supply and fixing in repair gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed. 122 supply and fixing in repair gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 15 mm bore pipe, including making connections complete all as specified and fixed. 123 supply and fixing in repair ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed ( minimum weight 20mm 210 gms ) . 124 supply and fixing in repair ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm bore pipe including making connections complete all as as specified and fixed ( minimum weight 25mm 455 gms ) . 125 s&f in repair pvc tank coversrequired for 500 ltr to 1000 ltr pvc water tanks complete all as specified and fixed 126 taking up or down steel tubing of 15 mm bore pipe and connections, including cleaning for re fixing or removal to store, complete all as specified and as directed 127 taking up or down steel tubing of 20 mm bore pipe and connections, including cleaning for re fixing or removal to store, complete all as specified and as directed 128 taking up or down steel tubing of 25 mm bore pipe and connections, including cleaning for re fixing or removal to store, complete all as specified and as directed 129 supply and fixing tubes medium grade galvanised, 15 mm bore, isi marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by engineer in charge 130 supply and fixing tubes medium grade galvanised, 20 mm bore, isi marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by engineer in charge. 131 supply and fixing tubes medium grade galvanised, 25 mm bore, isi marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by engineer in charge. 132 supply and fixing fittings for steel tubing galvanised, 15 mm bore, such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc complete all as specified and as directed 133 supply and fixing fittings for steel tubing galvanised, 20 mm bore, such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc complete all as specified and as directed 134 supply and fixing 20 mm nominal outer diachlorinated polyvinyl chloride ( cpvc ) pipes sdr 11, having thermal stability for hot & cold water supply, including all plain cpvc sdr 11 fittings & brass threaded fittings on walls / ceiling or laying in floors, including fixing the pipe with clamps. this includes jointing of pipes & fittings with one step cpvc solvent cement, complete as per direction of engineer in charge. make: supreme, prince, prayag. 135 supply and fixing 25 mm nominal outer diachlorinated polyvinyl chloride ( cpvc ) pipes sdr 11, having thermal stability for hot & cold water supply, including all plain cpvc sdr 11 fittings & brass threaded fittings on walls / ceiling or laying in floors, including fixing the pipe with clamps. this includes jointing of pipes & fittings with one step cpvc solvent cement, complete as per direction of engineer in charge. make: supreme, prince, prayag. 136 m&l cutting chases, pinning in , making good to facings where required and pointing in cement mortar1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting n.exc 10cm girth in brick walls. 137 s&f in repair stainless steel lock grating plain / hole size 100 mmdiaincluding embeding in tiles with white cement. make: jainko, essco, parko. 138 dismantling pvc / cement / ci pipes 50 to 110 mm diaincluding allfittings like bend, branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed 139 supply and fixing upvc ( swr ) type b pipes 110 mm bore single socketed in any length with rubber ringjoints, laid in trenches orin floors, complete all as specified and as directed by engineer in charge. make astral, supreme, finolex 140 supply and fixing upvc ( swr ) type b pipes 110 mm bore single socketed, in any length with rubber ringjoints fixedto walls including stack clamp of gi flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 141 supply and fixing upvc ( swr ) type b pipes 75 mm bore single socketed in any length with rubber ringjoints, laid in trenches orin floors, complete all as specified and as directed by engineer in charge. make astral, supreme, finolex 142 supply and fixing upvc ( swr ) type b pipes 75 mm bore single socketed, in any length with rubber ringjoints fixedto walls including stack clamp of gi flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by engineer in charge. make astral, supreme, finolex 143 supply and fixing, upvc ( swr ) , bends for75 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 144 supply and fixing, upvc ( swr ) , bends with access doorfor75 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 145 supply and fixing, upvc ( swr ) , bendsfor110 mm borecomplete all as specified and as directed by engineer in charge.make astral, supreme, finolex 146 supply and fixing, upvc ( swr ) , bends with access door, for110 mm borecomplete all as specified and as directed by engineer in charge.make astral, supreme, finolex 147 supply and fixing, upvc branch piece, single ( single y ) with access door for 75 mm bore complete all as specified and directed.make: astral, supreme, finolex. 148 supply and fixing, upvc branch piece, single ( single y ) with access door for 110 mm bore complete all as specified and directed.make: astral, supreme, finolex. 149 supply and fixing, upvc ( swr ) , junction single, ( single t ) with access door equal or unequal for 75 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 150 supply and fixing, upvc ( swr ) , junction single, ( single t ) with access door equal or unequal for 110 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 151 s&f upvc ( swr ) , reducers 110 mm dia complete all as specified. make: astral, supreme, finolex. 152 s&f upvc ( swr ) vent cowl 75 mm dia complete all as specified.make astral, supreme, finolex 153 supply and fixing in repair upvc ( swr ) floor trap plain with gratinghaving dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type b 1 ( 1:2:4 ) complete all as specified and directed.make astral, supreme, finolex 154 s&f in repair, upvc ( swr ) gully trap 125 / 110 mm, setting and jointing with solvent cement complete all as specified.make astral, supreme, finolex 155 rendering 15mm thck in cm 1:3 or plain cement concrete as in sunken floorswithout extra cement on walls / floors and including mixing of water proofing compound ( wpc shall be measured and paid separately ) 156 m&l applying a coat of bituminous primer conforming to is 3384on prepared surface of roof / sunken slab after drying of primer apply app based polymeric membrane minimum weighing 3kg / sqm and minimum 3mm thick reinforced with polyester non woven fabric ( wt not less than 150 gms / sqm ) laid on primed surface by forced torched application and finally apply a coat of hot blown 85 / 25 graded bitumen conforming to is 702 @ 1.2kg / sqm of plaster surface. 157 m&l cement concrete type e 2, 1:5:10 ( 40 mm graded agregate ) in sunkan ( up to 4th floor ) filling and mass concrete complete all as specified and directed by emgr in charge. 158 m&l 40 mm dia g i tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified. 159 demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable materialfrom the work site ouside defence premises complete all as specified. 160 m&l brick work with subclass b bricks, old size bricks, straight or curved onplan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by engineer in charge 161 m&l brick work with subclass b bricks, old size bricks, straight or curved onplan exceeding 6 metre mean radius built in cement mortar 1:6but except bricks complete all as specified and as directed by engineer in charge 162 m&l brickwork with subclass ‘b’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified. 163 material and labour for providing, cement concrete 1:2:4type b 1 ( using 20mm graded aggregate ) , in lintels upto1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed 164 demolition of cement concrete ( unreinforced ) ground floor to 4th floors and pavings n exc 15 cm thickness ( below or above ground level ) and removingthe rubbish from the work site out side defence premises complete all as specified. 165 dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface ( but not backing ) , removing serviceable tiles to store and rubbish off the premises. complete all as specied and directed. 166 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushingsurface with neat cement slurry with 3.0 kg of cement per sq. metre, removing serviceable tiles to store and rubbish off the cantt area complete all as directed 167 material and labour glazed ceramic coloureddigital tiles in vertical surface300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick cm 1:4 all as specified. ( sample as approved & kept in ges sample room ) 168 material and labournon skid digitalceramicjoint lesscoloured tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured / white cement to match the surface over and including15 mm thick screed bed in cm 1:4. ( sample as approved & kept in ges sample room ) 169 description all as item no 168 but as in vertical surfaces dado / skirting over and including a backing coat of cm 1:4, 10 mm thick complete. 170 material and labourvitrifiedceramic light shade tiles10 mm thick ( square / rectangular ) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured / white cement to matchover and including15 mm thick screed bed in cm 1:4. ( sample as approved & kept in ges sample room ) 171 description all as item no 170 but as in vertical surfaces dado / skirting over and including a backing coat of cm 1:4, 10 mm thick complete. 172 material and labourvitrifiedceramic ( double charged ) edge cutjoint freecoloured or printed any shade tiles10 mm thick ( square / rectangular ) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured / white cement to matchover and including15 mm thick screed bed in cm 1:4. ( sample as approved & kept in ges sample room ) 173 description all as item no 172but as in vertical surfaces dado / skirting over a backing coat of cm 1:4, 10 mm thick complete. 174 material and labour for chequered cement concrete tiles 30cm x30cm x 25mm thick, with greay cement and pigment, set, jointed and pointed in neat cement slurry in floors and laid over and including 20mm thick screed bed in cm 1:4 etc complete all as specified and as directed 175 material and labour for precast factory made interlockingdesigener tiles glazed topmade in white cement and pigment base of thickness not less than 19 mm indifferent colour and pattern ( compressive strength not less than 250 kg / sqcm ) setand jointed in neat cement slurry ( colour and pattern as per sample kept in ge office as approved by ge ) including 15 mm thick screed bedin cm 1:4. completeall as specified and directed by engr in charge. 176 providing and laying 60mm thick factory made chamfered edge cement concrete paver block of m 35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand 177 m&l 16 to 18mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick cm 1:4 as directed by engr in charge. 178 m&l rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified. 179 m&l for 50mm thick cement concrete 1:3:6, type c1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth ( comprising one part hot blown bitumen 85 / 25 and two part of sand ) , complete all as specified and directed. 180 material and labour for precast cement concretelouvers and jallies, 40 mm thick ( 1:2:4 ) type b 0 ( using 12.5 mm graded aggregate ) set in cement mortar 1:6, including all mouldingsand dismantling old u / s broken jallies at site, complete all as specified. 181 m&l for plain cement concrete ( 1:3:6 ) , type c 2 ( using40 mm graded crushed stone aggregate ) nominal mix, 75 mm thick, as in sub base offloors, finished even and faircomplete all as specified and as directed by engineer in charge. 182 m&lfor 25 mm thick cement concrete 1:2:4, type b 0, ( using 12.5 mm graded crushed stone aggregate ) as in sub base / levelling course of floors, finished even and faircomplete all as specified and directed. 183 supply and fixing in repair for bevelled edge mirror of size ( 600x450mm ) , selected quality glass approved size , mounted on 6 mm thick ac building board or commercial plywood and fixed to wooden plugs with ss screws and cup washers. 184 s&f in repair, pvc cabinet mirror ofselected quality glass approved size ( 330mm x 430mm ) , fix with screw complete all as specified. make: prayag, cat no: 551 or equivalent to jaquar, cera 185 supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen orlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 200mm complete with cp waste coupling & pvc waste pipe complete all as specified anddirected by engineer in charge. make: jainko, model no ssj 1. & equivalent in prayag, nirali, jayana. 186 s&f sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with cp waste coupling & pvc waste pipe complete all as specified anddirected by engineer in charge. make: jainko model no . ssj 8. & equivalent in prayag, nirali, jayana. 187 s & f kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. the over all size ( 30x36x10 ) fixed with steel fastners or steel screw complete.make: jainko, model no.krj 4. and equivalent in prayag, nirali, jayana. 188 dismantling of bricks ( laid flat or on edge ) or brick tiles in floors, channels, kerbs, aprons, etc. ( each layer ) , laid, bedded and pointed in any mortar, complete as specified and directed. 189 complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster / demolition of cement concrete any thickness and removal of debris off the premisesincluding grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt / dust. 190 m&l for p.c.c 1:2:4 type b 0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed. 191 m&l rendering 15mm thck in cm 1:4 on concrete surfaces of rooffinished fair & even and including mixing of water proofing compound ( wpc shall be measured and paid separately ) 192 m&lforwater proofing treatment inthe following sequences: ( a ) applying1st course of bituminous primer conforming to is 3384 @ 0.4 kg / sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely ( bi ) applying2nd coat of blown 85 / 25 graded bitumen confirming to is 702 @ 1.2 kg / sqm. ( c ) applying 3rd course of app ( atactic polypropylene ) modified polymeric membrane 3 mm thick weight not less than 3.6 kg / sqm with 160 grams / sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. the membrane has to be laid with lpg torch and overlap sealed and finished neat complete all as specified and as directed. 193 m&l for preparation of newly sufrace of app membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc 194 m&l 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar ( 1:3 ) mixed with 5% of crude oil by weight of cement on mud phuska 195 cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by engineer in charge. 196 supply only water proofing compound liquid. 197 cleaning of roof surfaces of rcc roof ( any type ) tiles with brush and removing all vegetation, plants, roots, grass, leaves any type ofmaterial asked to remove at any height of bldg or any part of bldg complete all as directed. 198 m&l for repairing of concrete surfaces such asbalcony, chajjas, upward or downward facias , column, pillar, ceiling and similar items with plain cement concrete 1:2:4type b 0 or rendering 10 15mm thickas per site requirement in cm 1:3 without using extra cement finished even and fair complete all as specified and directed ( up to fourth storey bldgs and including necessory formwork and scaffolding required as per site condition also taking down or dismantling as required at site. 199 m&l for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width / girth exceeding 10 cmincluding preparation and rubbing with sand paper to make surface even and smooth complete all as specified. 200 m&l for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width / girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth. 201 demolition ofreinforced cement concrete of any discription ground to 4th floors and removingthe rubbish from the work site out side defence premises complete all as specified. 202 m&l for rcc m 15, nominal mix, type b 1 ( 1:2:4 ) , using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specifiedand directed. 203 m&lfor tmtmildsteel bars10mm dia and over, cutto length, bentto shape required, including cranking, bendingspirallyforhooping for column, hookingendandbinding withandincludingmildsteelwire ( annealed ) not lessthan0.9 mm dia or securing with clips, complete all as specified and directed. 204 m&l for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick ( horizontal or sloping ) for rough finished surfaces of concrete, complete all as specified and directed. 205 m&l for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar workexc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed 206 repair to existing pvc pipe / ci pipe including making the joints water tight by using suitable material including cleaning if requiredand refixingof any dia. note :work to be carried out up to 4th storey bldg in any condition of working place / area 207 material and labour for sealing of wc / floor traps joint and joints between rain water pipe and roofby using neat white cement paste or leak proof material and making the joint leakproof in case seepage is observed from wc / floor trap and joint of rain water pipe and roof slab.note :work to be carried out up to 4th storey bldg in any condition of working place / area 208 taking down carefully aluminium conductor point wiring ( light, fan, light socket, power socket ) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed. 209 m&l for complete point wiringwith 1.5 sqmm single core multi stranded copper conductor frlsh pvc insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible frlsh pvc insulated drawn in and including concealed pvc rigid conduit medium gradeisi marked terminated into gi modular sunken boxes including white cover plate with frame as per relevant isfor mounting moudlar switches, sockets, fan regulators etc complete all as specified and as directed for the following : ( a ) one light / fan point / exhaust fan point controlled by one way switch 6 amps. 210 ( b ) one 3 pin socket outlet 6a point on same board. 211 all as per srl item no 209 above but for one 3 pin socket outlet 15 amp independent with cable of size 2.5 sqmm for point wiring and 2.5 sqmm as in continuous earth wire. 212 s & f moudlar switch piano flush button single pole one way, 6 amp, 1 moudle. complete all as specified and directed. 240 v 213 supply and fix moudlarsocket outlet 2 in 15 pin, 6 amps made of polycarbonate flush type complete all as specified and as directed. 214 supply and fix moudlar socket outlet 2 in 15 pin, 6 & 16 amps flush type made of polycarbonate complete all as specified and as di rected. 215 supply and fix moudlarswitch piano made of polycarbonateflush button single pole one way, 16 amps, 230 / 240 v complete all as specified and as directed by engineer in charge. 216 preparation of old decorated brick / concrete, plastered / un plastered surfaces of walls, pillars, cornices etc ( upto four storey bldgs ) by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, rubbing with sand paperand applying one coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed. 217 preparation of old decorated brick / concrete, plastered / un plastered surfaces of ceilings, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying one coat of white wash on ceiling, complete all as specified and directed. 218 preparation of old decorated brick / concrete / plastered / unplastered surfaces of walls, pillars, cornices etcby booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of oil emulsion distemper onwalls, pillars, cornices surface including making good uneven surface / holes with birla wall care putty coloured in same shade where ever required etc. complete all as specified and directed. 219 complete removal of existing treatment including washing, rubbing down with sand paper and stopping of distempered and painted surfaces including preparation of old plastered surfaces of walls andapplying two coats of distemperoil emulsion over and including one coat of primerover two coats ofbirla wall care putty 1 to 2 mm thick on plastered surfaces, preparatory to distempering. complete all as specified and as directed by engineer in charge. 220 preparation of old decorated brick / concrete / plastered / unplastered surfaces of walls, pillars, cornices etcby booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of cement base paint on walls, pillars, cornice etc ( upto 4th storey with necessary scaffolding complete all as specified and directed. 221 preparation of old decorated brick / concrete / plastered / unplastered surfaces of walls, pillars, cornices etcby booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applyingtwo coats of cement base paint on walls, pillars, cornice etc ( upto 4th storey with necessary scaffolding complete all as specified and directed. 222 complete removal of existing treatment including washing, rubbing down with sand paper and stopping ofpainted surfaces including preparation of old plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. andapplyingone coat of weather proof exterior emulsion ( apex ) making good uneven surface / holes with birla wall care putty coloured in same shade where ever required etc ( up to 4th storey with necessary scaffolding ) complete all as specified and directed. 223 preparation of old painted wooden surfaces having width / girth exceeding 10 cm including necessry putty filling with knife of same colour where required to achieve smooth and even surface and applying one coat of synthetic enamel paint on wood surfaces of any description ( up to 4th storey with necessary scaffolding ) complete all as specified and directed 224 preparation of old painted steel surfaces having width / girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying one coat of synthetic enamel paint on steel surfaces of any description ( up to 4th storey with necessary scaffolding ) complete all as specified and directed...

Due Date : May 16, 2022

Tender Value : ₹ 45 Lakhs

View Tender
46
North Western Railway - Rajasthan

31020776 auction sale of abandoned 40 nos type i quarters, released rubble stone 705.57 cum, released stone slab 462.00sqm, released ac sheets 88.80sqm, released steel girders 5860.80 kg, released steel doors of different sizes 1855 kg, released steel windows 600 kg, ...

Due Date : February 16, 2022

Tender Value : ₹ Ref. Documents

View Tender
47
North Western Railway - Rajasthan

31020760 auction sale of abandoned 48 nos type i quarters, released rails us ( rm ) 41 / 1aprox. wt2566.08 kg, released rails us 50r aprox. wt 491.04 kg, released rubble stones 897.99 cum, released stone slab 617.10 sqm, released half bricks 297.04sqm, released wooden windows 24 nos, released wooden doors 36 nos, released u / s steel jeffery 132.90 kg, released ac sheets47.61sqm, released steel girders 3516.48 kg, released steel doors of different sizes 1125 kg, released steel window 360 kg, ...

Due Date : February 16, 2022

Tender Value : ₹ Ref. Documents

View Tender
48
Military Engineer Services - Rajasthan

30860798 provn of certain lbw and rw work at lgj mil stn provn of certain lbw and rw work at lgj mil stn supply of portionexcavation in trenches n.exc. 1.5m wide and n.exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out in getting out in soft/ loose soil complete all as specified and directed by engineer in charge 2 , ditto all as per serial item no 1 above but add for each additional 1.5m or part thereof in depth beyond the first 1.5m complete all as specified and directed by engineer in charge 3 m&l for pcc 1:4:8 type d2 using 40mm graded stone aggregate in foundation, filling & mass concrete complete all as specified and directed by engineer in charge 4 m&l for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finish surface of concrete flat complete all as specified and directed by engineer in charge 5 m&l for formwork to sides of pillars, columns etc; rough finish surface of concrete square, rectangular or polygonal complete all as specified and directed by engineer in charge 6 m&l for formwork to sides and soffits of floor or roof beams, beam hunchings, girders, bressummers, lintels, cantilevers, etc. also splays between floors and beams, etc. rough finish surface of concrete flat complete all as specified and directed by engineer in charge 7 m&l for formwork to chajjas, troughts and similar items including edges rough finish surface of concrete flat complete all as specified and directed by engineer in charge 8 m&l for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200 mm thick (horizontal or sloping) rough finish surface of concrete flat complete all as specified and directed by engineer in charge 9 m&l for fromwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and sides of rcc/pcc bands in walls, orizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide, roughed finished surfaces of concrete all as specified and directed. 10 s&f for tmt bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed. 11 ; ditto all as per item ser no 10 above here in before but 6 mmto 8 mm dia complete all as specified and directed by engineer in charge. 12 ; ditto all as per item ser no 10 above here in before but 5 mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by engineer in charge. 13 m&l for reinforced cement concrete (design mix) m 25 using 20mm graded stone aggregrate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, pillers etccomplete all as specified and directed by engineer in chargenote : reinforcement shall be measured and paid seperately. 14 m&l for reinforced cement concrete (design mix) m 25 using 20mm graded stone aggregrate in columns, pillers etccomplete all as specified and directed by engineer in chargenote : reinforcement shall be measured and paid seperately. 15 m&l for reinforced cement concrete (design mix) m 25 using 20mm graded stone aggregrate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by engineer in chargenote : reinforcement shall be measured and paid seperately. 16 m&l for reinforced cement concrete (design mix) m 25 using 20mm graded stone aggregrate in chajjas complete all as specified and directed by engineer in chargenote : reinforcement shall be measured and paid seperately. 17 m&l for reinforced cement concrete (design mix) m 25 using 20mm graded stone aggregrate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like; all as specified and directed.note : reinforcement shall be measured and paid seperately. 18 m&l for brickwork with fly ash bricks, of old size bricks, straight or curved exc. 6 m mean radius built in cm (1:6) complete all as specified and directed by engineer in charge 19 m&l brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, buit in cm (1:4) complete all as specified and directed by engineer in charge 20 m&l for 40mm thick damp proof course in cement concrete 1:2:4, type b 0, 12.5 mm graded stone aggregate with wpc to horizontal or vertical surfaces including necessary formwork complete all as specfied and directed by engr in charge. note : approved water proofing compound shall be measured and paid separately as supply only. 21 returning, filling in, including spreading levelling including watering & well ramming in layers n. exc 25 cm all complete as specified in soil complete all as specified and directed by engineer in charge 22 spreading and levelling in layers n.exc 25cm thick and well ramming including watering as required under floors; all as directed. (in floor with available earth from excavation approved complete all as specified and directed by engineer in charge 23 removing excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed by engineer in charge 24 m&l for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area (area of the sub structure in contact with excavation such plinth beam, etc. to be measured) complete all as specified and directed by engineer in charge 25 m&l for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of the sub structure in contact with backfill to be measured) complete all as specified and directed by engineer in charge 26 m&l for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified. 27 m&l for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by engineer in charge 28 m&l for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc.15cm thick,watered and rammed to a true surface in broken stone or boulders (15cm compacted thickness) complete all as specified and directed by engineer in charge 29 m&l for 75 mm thick pcc 1:3:6 type c 1 using 20 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixturecomplete all as specified and directed by engineer in charge 30 m&l for 75mm thick pcc (1:4:8) type d2 using 40mm graded stone aggregate as in sub base below floors complete all as specified and directed by engineer in charge 31 m&l for 40 mm thick pcc (1:2:4) type b 0 using 12.5 mm graded stone aggregate as in floor or laid under floor etc complete all as specified and directed by engineer in charge 32 m&l for 38 mm wide glass dividing strips, 4mm thick and inserted in positionas in flooring complete all as specified and directed by engineer in charge 33 m&l for 5 mm thick setting coat as in skirting, trowelled to even and smooth finish incement mortar 1:2, complete all as specified and directed by engineer in charge 34 m&l for joint free non skid ceramic coloured tiles 7 to 8 mm thick, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floorcomplete all as specified and directed by engineer in charge 35 m&l for joint free glazed ceramic coloured tiles of size 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by engineer in charge 36 m&l for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding to edges of stone slabs one edge complete all as specified and directed by engineer in charge 37 m&l forrendering, 10 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement complete all as specified and directed by engineer in charge 38 m&l forrendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall and on roof surfaces when concrete is green finished even and fair with wpc complete all as specified and directed by engineer in charge.note : wpc shall be measured and paid separately as supply only. 39 m&l forrendering, 5 mm thick on brick work or concrete surfaces in cement mortar 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed by engineer in charge 40 supply only intregral water proofing compound complete all as specified and directed by engineer in charge 41 m&l for three coats of white wash on newly/old plastered surfaces incl preparation etc complete all as specified and directed by engineer in charge 42 m&l for three coats of white wash on newly /old plastered surfacesof ceilingincluding preparation of surfaces complete all as specified and directed by engineer in charge 43 m&l for two coats of cement base paint on newly plastered surfaces including preparation etc. complete on wall complete all as specified and directed by engineer in charge. 44 material and labour for water proofing treatment over rcc slab by applying one coat of bituminous primer @ 0.25 kg/sqm and providing 3mm thick app modified water proofing membrane weighting not less than 3.5 kg/sqm, reinforced with non woven polyster reinforcement mat weighing not less than 160 gm/sqm, polyster core having softening point not less than 150 degree c, longitudinal tensile strength not less than 650 n/5cm, tearing strength of 180n/5cm incouding two coat of solar reflective aluminium paint @ 0.15kg/sqm including cleaning the newly plastered surfaces of concrete/exisisting plastered vertical surfaces with wire brushes free from dust etc complete all as specified and directed by engineer in charge 45 s&f for factory made window, made out of ms hollow section of size 79mm x 39mm x 1.6mm thick frame with double shutter (glazed and wire guage shutter) made out of z section using flush butt welding and tenon riveting all as per is 1038/83, dobby hinges shall be provided to both shutter, locking arrangement as per sample approved by ge, provided with knob z section handles 100mm size and 150 mm long hook and eye welded to frame and shutter,four number legs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fastand making good disturbed surfaces in pcc(1:2:4) type b1 to match with the existing surfaces complete all as specified & directed by engineer in charge. 46 s&f for factory made steel ventilators all as per is 1038/83, with top hung shutters including hinges, steel peg stay, complete all as specified & directed by engineer in charge. 47 s&f for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spiles; framed guard bars; barred iron doors; ladders; framed balusteres; walk ways; railings; framework of water tanks and similar work fonforming to fe. 290, gde e 165 withcomplete all as specified and directed by engineer in charge 48 s&f for framed work as in chowkats of doors windows of angle iron ,gates or other section with gusset plates, rails, braces etc conforming to gde fe 410 0 or fe 310 0 complete all as specified and directed by engineer in charge. 49 s&f for hold fast of flat iron 25 x 3 mm conforming to fe 290 or fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified and directed by engineer in charge 50 m&l for cement concrete 1:3:6 type c–1 (using 20mm graded crushed stone aggregate) as in coping, hold fast, bed blocks or similar block etc complete all as specified and directed by engineer in charge. 51 s&f for 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 (part i), kiln seasoned and chemically pressure treated complete all as specified and directed by engineer in charge 52 s&f for 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me mbers of shutters as specified in ssr part i, section 8, clause 8.24 (a) complete all as specified and directed by engineer in charge 53 supply and fixing of fibre glass reinforced plastic (frp)door frame of required built in colour in three legged of cross section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick includinglaminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(csm) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides ms stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specifiedand as directed by engineer in charge. 54 supply and fixing of 30 mm thick glass fibre reinforced plastic (frp) paneled doorshutter conferming to is:14856 2000 of required colour andmade with fire retardant grade unsaturated polyster resin,moulded to 3mm thick frp laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick frp laminated for panels including fixing to frames,complete all as specified and as directed by engineer in charge. 55 s&f for 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anosied and fixed type b 21 complete all as specified and directed by engineer in charge 56 supply only 100mm long butt hinges mild steel medium weight cold rolled including necessary welding etc. to steel frame complete all as specified & directed by engineer in charge. 57 supply only 50mm long butt hinges mild steel medium weight cold rolled including necessary welding etc. to steel frame complete all as specified & directed by engineer in charge. 58 s&f for 300 mm long mild steelsliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by engineer in charge 59 s&f for 200 mm long aluminium anodisedbarrel tower bolt, of extruded sections complete all as specified and directed by engineer in charge 60 s&f for 125 mm long aluminium anodised handle, cast type complete all as specified and directed by engineer in charge 61 s&f for 150 mm long extruded aluminium alloy handle, fabricated type anodised complete all as specified and directed by engineer in charge 62 s&f for 300mm ordinary rat tail rod pattern springs including roller and roller platecomplete mild steel fixed complete all as specified and directed by engr in charge. 63 s&f for 2nd class hard wood (sal) or any other 2nd class hard wood articles not exceeding 200 cubic centimetre each as small fittings such as shaped door and window stops and the like, including necessary labour etc complete all as specified and directed by engineer in charge 64 s&f for stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture1.40 mm and fixed with stainless steel wire staplescomplete all as specified and directed by engineer in charge 65 , ditto all as per serial item no 64 above but fixed in repair complete all as specified and directed by engineer in charge 66 s&f for 3mm thick sheet glass ordinary quality and glazing with spring clips in metal surrounds and oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified and directed by engineer in charge . 67 s&f for 3mm thick figured glass, pin head type and glazing with spring clips in metal surrounds and oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified and directed by engineer in charge . 68 m&l for preparation of new steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer all as specified. 69 m&l for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by engineer in charge 70 s&f vitreous china squatting pan orissa pattern size 580 x 440 mm white with integral foot rests (excl flushing cistern) but including p trap set in and provision of lime concrete bedding complete complete all as specified and directed by engineer in charge 71 s&f vitrieous chinawash down wc (pedestal pattern) whiteand flush piple including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc.,complete all as specified and directed by engineer in charge 72 s&f plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, seat and cover for water closet (european type) complete all as specified and directed by engineer in charge 73 s&f vitreous china wash basin counter top (bowl type/oval shape) of size 560 x 450mm, long screwed shank fly nut flangeend including cutting for and pinning in ends of brackets in 1:3 cm including 32mm dia chromium plated waste coupling/trap complete all as specified and directed by engineer in charge 74 s&f vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including conncetion to flushing pipe and waste pipe providing and fixing plugs bedding urinal against wall complete all as specified and directed by engineer in charge 75 supply only pvc valve less, syphonic action type flushing cistern,10 ltrs capacitylow level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or pvc, 32mm dia, for low level cisterncomplete all as specified and directed by engineer in charge 76 s&f 15 mm dia stop valve, fany type chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipecomplete all as specified and directed by engineer in charge 77 s&f 15 mm dia stop valve/angle valve, fany type chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by engineer in charge 78 supply and fix pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed in 15mm dia bore pipe complete all as specified and directed by engineer in charge 79 supply and fix bib taps, cast copper alloyfancy type chormium plated. with crutch or butterfly handle screwed down screwdd for iron pipe of brass ferrule, and fixed in 15 mmbore dia of pipe complete all as specified and directed by engineer in charge 80 s&f chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by engineer in charge 81 s&f pvc connections 15 mm size with ptmtnuts of length 450 mm complete all as specified and directed by engineer in charge 82 s&f urinal spreader of ptmt any clolour for fixing with 15mm dia pipe, (minimum weigfht 60 gms) complete all as specified and directed by engineer in charge 83 s&f shelf of ptmt fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 300 gms) complete all as specified and directed by engineer in charge 84 s&f looking mirror of selected quality of size600 mm x 450 mm withbevelled edge mounted 6 mm thick commercial plywood and aluminium channel of required size fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by engineer in charge 85 s&f brass chromium plated tubular towel rail, 20mm dia, d type, 60cm long between flanges complete all as specified and directed by engineer in charge 86 s&f brass hat pegs, solid body, 125 mm to 175 mm (4 legs) complete all as specified and directed by engineer in charge 87 s&f rotational moulded polythene water storage tank 500 ltr capacity of tripple layer vertical with closed top hoisted and fixed in position all as specified in ssr part i. complete all as specified and directed by engineer in charge 88 s&f ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified and directed by engineer in charge 89 s&f gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair compete all as specified and as approved by ge/engineer in charge. 90 supply, layingand jointing g.i tubes, 15 mm bore dia of pipe, medium grade in lengths with screwed and socket jonts, together will allgalvanised steel fitting such as sockets, elbows , bends, tees reudcers unions caps plugs,nippples, short pieces etc fixed complete to walls by means of and including clips, wall hooks etc, or laid on surfaces/ floors or concealed in walls/ floors,complete all as specified and directed by engineer in charge 91 , ditto all as per serial item no 90 above here in before but 20 mm bore dia of pipe complete all as specified and directed by engineer in charge 92 s&f 110 mm dia pvc swr pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by engineer in charge 93 s&f 75 mm dia pvc swr pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by engineer in charge 94 s&f 110 mm dia pvc (swr) bend any radius complete all as specified and directed by engineer in charge 95 s&f 75 mm dia pvc (swr) bendany radius complete all as specified and directed by engineer in charge 96 s&f 110 mm dia pvc (swr) junction single, (single t) equal or unequal complete all as specified and directed by engineer in charge 97 s&f 110 mmdia pvc reducer complete all as specified and directed by engineer in charge 98 s&f pvc vent cowl complete all as specified and directed by engineer in charge 99 s&f pvc (swr) floor trap, 75 mm dia with grating including jointing with solvent cement etc complete all as specified and directed by engineer in charge 100 surface dressing not exceeding 15cm deep in soft/loose soil complete all as specified and directed by engineer in charge 101 surface excavation n.exc. (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by engineer in charge 102 m&l for precast cement concrete 1:2:4 type b1 using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in cm 1:4 complete all as specified and directed by engineer in charge 103 m&l for 100mm thick pcc (1:4:8) type d2 using 40mm graded stone aggregate as in sub base below floors complete all as specified and directed by engineer in charge 104 m&l machined pressed precast concrete interlocking paver block glossy with grey cementand pigment, any shape and size confirming to is 15658 2006 of 60mm thickness m 40 grade with over 50mm thick fazilka sand cushion complete all as specified and directed by engineer in charge 105 m&l for pcc 1:3:6 type c1 as in coping including necessary formwork, weatherig, slightly rounded or chamfered angle and throating complete all as specified and directed by engineer in charge 106 m&l for pcc 1:2:4 type b2 using40mm graded aggregates as in benching / haunchig ofmanholes including forming channels including necessary formwork etc.complete all as specified and directed by engineer in charge 107 m&l precast cement concrete 1:2:4 type b1 using 20mm graded stone aggregate and set cement mortar 1:6 as in cover slabs (for manholes etc,) chajjas, shelves and similar articles with plain faces all as directed 108 m&l rendering 10mm thick on fair face of brick work in cement mortar 1:4 and finished surfaces even and smooth without using extra cement as specified including wpc complete all as specified and directed by engineer in charge note : (wpc shall be measured and paid seperately) 109 material and labour for moorum bed to drain pipes, spread, levelled and rammed including wateringcomplete all as specified and directed by engineer in charge. 110 supply and laying dpcpe (sn8) 180 (od)/163 (id) mm diameter drain pipes as per is 16098 (part ii), laid in trenches on moorum bed to required slope, including all accessories/fittings, jointing and tested complete all as specified and as directed by engineer in charge 111 cutting into existing manholes for connection of new drain making pipes and rendering cutting out existing benching & forming branch channel in pcc 1:2:4 type b1 smooth finished & forming benches as reqd etc for 150 mm bore complete all as specified and directed by engineer in charge 112 demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) complete all as specified and directed by engr in charge 113 demolition of reinforced cement concrete of any description and in any position not otherwise specificlly provided for (reinforcement cut as required to facilitate demolition) all as specified and directed.. 114 m&l for reinforced cement concrete 1:1.5:3 type a 1 using 20mm graded stone aggregrate in chajjas; complete all as specified and directed by engr in chargenote : reinforcement shall be measured and paid seperately. 115 demolition of brick work or stone/boulder masonry, built in cement mortar including allquoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concretecomplete all as specified and directed by engineer in charge 116 m&l for pcc 1:2:4 type b1 using20mm graded aggregates as in coping, roof kerbs or mud stop and the like including weathering.slightly rounded or chamfered angles and throating, as directed including necessary formwork etc complete all as specified and directed by engineer in charge 117 dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removingrubbish off the premises complete all as specified and directed by engineer in charge 118 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by engineer in charge. 119 taking down cement plaster of any description from brick walls or concrete surfaces of walls and ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by engineer in charge. 120 material and labour for rendering/plastering 15mm thick in cement mortar (1:6) on any fair face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the engineer in charge. 121 m&l for two coats of oil bound distemper on newly plastered surfacesof walls paint over 3mm thick wall care putty including preparation of surfaces complete all as specified and directed by engineer in charge 122 m&l for water proofing treatment to rcc sunken slabas specified below and as directed by engineer in charge. : (a) applying 15 mm plaster in cm 1:3 with wpc on verticle and horizontal surface (b) cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c)creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d)apply first coat of two component modified polymer coating on the horizontal and verticle surface(e)provision of glass fiber mesh of 2 x 2 mm of gsm 145 immediately on above coating (f) apply second coat of two component modified polymer coating after 72 hrs (h) joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete all as specified and directed by engineer in chargemanufacturer. make: dr. fixit/fosroc/stp note: (i) the treatment shall be carried out by approved authorised applicator as per the manufacturers instructions and as directed by the engineer in charge. (ii) the plan area of floor shall be considered for payment and provn of cement work pcc is included in quoted rate for this item. 123 demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed by engr in charge 124 disconnecting existing serviceable pvc tanks of capacity upto 500 litre, setting aside (or lowering if required) for repairs, cleaning , etc. and hoisting if required reconnecting and re fixing in original position including all inlet and outlet water connection after removing all scale and dirt from tanks and from mouths of circulating pipes and re fixing existing ms frame and writing of dates of cleaning and due with synthetic enamel paint and stensil complete all as specified and as directed by engineer in charge. 125 m&l for roof treatment to rcc roof as follows: (a) cleaning the roof surfaces thoroughly using wire brusehes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/plaster etc.(b) providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with wpc, finished even and smooth without using extra cement.(c) providing one coat of approved bituminous primer @100 gms per sqm, over dried plastered surface.(d) laying 3 mm thick app membrane,(mineral finish) reinforced with non woven polyster fabric, by torch application. the overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by e in charge.make : stp dr fixit/pidilite, texsa india ltd/tikitar dansona/bengal bitumennotes :(i) all joints and change in directions should be covered wih cement mortar (1:3) mixed with sbr latex @ 200 ml/bag of cement/as per site reqmt and cured well before laying membrane by torching.(ii) all angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. the name of firm shall be got approved from ge before carrying out the wk. (iv) the independent testing of membrane for technical parameters given in particular specifications shall be carried out from govt approved labs having fascilities for testing of membrane.(v) the guarnatee of treatment shall be for min 10 yrs reckoned from date of completion of whole wk. 126 m&l lime concrete terracing as specified in roof (excluding bitumen tack coat) complete all as specified and directed by engr in charge. 127 m&l 40mm thick brick tiles laid flat on lime concrete & joints grouted flush in cement mortar (1:3) bedded in 15mm th cement morter (1:6) mixed with 5% of crude oil by weight of cement on lime concrete complete all as specified and directed by engr in charge. 128 , ditto all as per serial item no 127 above but except tiles complete all as specified and directed by engr in charge 129 m&l racking out joints/pointing to brick work or brick tiles laid flat in floors, surface channels, roofs etc. and flush pointing to bricks laid flat or brick tiles in pavings and roofs in cm 1:3 all as specified and directed. 130 taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by engr in charge 131 taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by engr in charge 132 taking down shutters of any description exc 1 sqm and n.exc 2 sqm each complete all as specified and directed by engr in charge 133 s&f framed work as in chowkats of doors windows of angle iron ,gates or other section with gusset plates, rails, braces etc conforming to gde fe 410 0 or fe 310 0 complete all as specified and directed by engineer in charge. 134 s&f hold fast of flat iron 25 x 3 mm conforming to fe 290 or fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified and directed by engr in charge 135 supply & fixing, factory made steel windows all as per is 1038/83, with side hung shutters including box type hinges, mshandle, peg stay, 02 nos ms tower bolt 100mm long for each leaf complete with glazing bars dovetailed or welded, including cutting holes in brick wall, fixing in pcc (1:2:4 type b 1 and making good complete all as specified & directed by engineer in charge. 136 supply & fixing, factory made steel windows all as per is 1038/83, with side hung shutters including box type hinges, mshandle, peg stay, 02 nos ms tower bolt 100mm long for each leaf complete without glazing bars dovetailed or welded, including cutting holes in brick wall, fixing in pcc (1:2:4 type b 1 and making good complete all as specified & directed by engineer in charge. 137 supply & fixing, factory made steel ventilators all as per is 1038/83, with top hung shutters including hinges, steel peg stay, fixing lugs in pcc (1:2:4) type b 1 and making good complete all as specified & directed by engineer in charge. 138 s&f mild steelms grills of any section to windows / ventilators conforming to fe 290 gde e 165 complete all as specified and directed by engr in charge 139 taking down existing shutter and refixing in same opening shutters of any description exc 1.0 sqm but not exc 2.0 sqm each all as specified and directed.(note: refixing includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.complete all as specified and directed by engineer in charge 140 s&f for 300mm long aluminium alloy, anodised, sliding door bolt typenot less than 16mm dia fixed complete all as specified and directed by engineer in charge 141 s&f 150 mm long aluminium anodised handle, cast type complete all as specified and directed by engr in charge 142 s&f 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.5 sqm in each pane complete all as specified & directed by engineer in charge. 143 s&f 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as directed. 144 s&f in repairs 25mm dia aluminium pipe coated with pvc sheet as in drapery curtain rod with decorative end knobs complete with brackets and fixed on wall complete all as specified and directed by engineer in charge 145 taking down 15 mm dia steel gi tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe complete all as specified and directed by engineer in charge 146 , ditto all as per serial item no 145 above but20mm dia pipe complete all as specified and directed by engr in charge 147 s&f 15 mm diagalvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etcfixed to walls / ceiling complete all as specified and directed by engr in charge 148 , ditto all as per serial item no 147 abovebut 15mm dia pipe fixing only complete all as specified and directed by engr in charge 149 , ditto all as per serial item no 147 above but20mm dia pipe complete all as specified and directed by engr in charge 150 , ditto all as per serial item no 147 above but 20mm dia pipe fixing only complete all as specified and directed by engr in charge 151 taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks etc., including cleaning or refixing or removal to store (measured overalll as fixed along the cente line over fittings and accessories) complete all as specified and directed by engr in charge 152 s&f 110 mm bore pvc (swr) branch piece double (single y) equal or unequal complete all as specified and directed by engr in charge 153 s&f 75 mm dia pvc (swr) bend with access door any radius complete all as specified and directed by engr in charge 154 m&l pvc (swr) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by engr in charge 155 excavating in post holes (or similar holes) each n.exc 0.5 cum getting put, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm in hard/dense soil complete all as specified and directed by enginee in charge. 156 m&l for pcc 1:3:6 type c2 using 40mm graded stone aggregate in foundation, filling & mass concrete complete all as specified and directed by engineer in charge 157 m&l for 40mm thick pcc (1:2:4) type b 1 using 20mm graded stone aggregate as in floor finished even and smooth without using extra cement complete all as specified and directed by engineer in charge 158 m&l for filleting in any position and to any shape in cement mortor 1:4 including all mitres stops etc section of filet n.exc 25sqm complete all as specified and directed by engineer in charge 159 s&f steel work in tubular/hollow section in trusses, rafter, purline post etc.including special shaped washer, plate, cleat etc complete using erw or induction butt welded tubes conforming to is 1161 1979 grade st 240 complete all as specified and directed by engineer in charge 160 s&f pre painted galvalume aluminum zinc coated gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge 161 m&l for preparation of new steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed by engineer in charge. 162 s&f framed work with stainless steel material such as grills, grating etc, of ormamental and intricate design with ends of bars shouldered and/or riveted, or forged into spiles, framed guard bars, barred iron doors, ladders framed balusteres, walk ways railings framework of water tanks and similar work conforming to fe 290 gde e 165 with complete all as specified and directed by engineer in charge 163 s&f for anodised aluminium frame cleat for fixing one or more rebates including jointing cleats for fixing etc complete all as specified and directed by engineer in charge. 164 s&f anodisedaluminium door shutters with powder coated aluminium sectionweighing 0.5 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing handles 2 nos in each door, hinges, anodised aluminium snap beading screwscomplete all as specified and directed by engineer in charge. 165 s&f mortice lock 4 lever vertical type, size 100mmbrass complete all as specified and directed by engineer in charge 166 m&l 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by engineer in charge. 167 m&l for 12mm thick prelaminated partile board, exterior grade, prelaminated one side with decorative choice laminated & other side balancing whhite laminated fixed with screws to aluminium frame work complete ...

Due Date : February 17, 2022

Tender Value : ₹ Ref. Documents

View Tender
49
Department Of Training And Technical Education - Rajasthan

30505900 open tenders are invited for supply of tools and equipments for fitter trade vernier caliper surface plate file square second cut , file flat second cut safe edge , file flat bastared , file round bastard , file hand second cut , wooden handle forged soldering iron copper bit wooden handle forged soldering iron copper bit. 350 gm 4 9 hand reamer set (tapar pin straight flute) nominal dia 6, 8, 10, 12, 16mm high speed steel 2 10 fire extinguisher (for 4 units) co2 type, foam type 3 kg capacity 2 each 11 torque wrench (standard/ratchet type) 14 to 68 nm drawi size 12mm length 476mm 2 12 power tools for fastening capacity 10 18mm voltage 18v,battery capacity 5.0 ah,max.torque 447 nm,breakaway torque 813 nm,no load speed 0 900/2000 rpm,impacts per minute 0 3100ipm,max bolt dia m18,tool holder 13mm, weight 2.12 kg,with 2 batteries variable speed trigger help to provide speed control,led light to help illuminate dimly lit areas 2 13 different profile gauges (plate type) for demonstration metric standard working length 190 mm,max. profile depth 81 mm,needle diameter 1.0 mm 8 14 temperature gauge range 0 150°c temperature element : gas inmetal,stem diamater : 8 mm,stem length : 80 to 250 mm,ranges available : ( 20 to 80)(0 to 60)(0 to 100)(0 to 160)deg. c,case : stainless steel,window : safety glass,dial : white aluminium,pointer : adjustable pointer,accuracy : 1 % of fs,connection : 1/2 bsp 2 15 dowel pin ( straight) dia. 1 length 4 (mat: stainless steel) 2 16 standard tap screws m3, m4, m5, m6, m8, m10, m1 lapping plate dia. 6 hand scrapped finish 4 18 caps screws m6, m8, m10, m12 4 19 drill gauges letter drill gauge (a to z) , number drill gauge (1 to 60) , metric drill gauge (1.5mm to 12.5mm, 30 holes) titanium_grade_5 4 20 cast iron globe valve (flanged type) 150nb, class# 150 flange:ansi125 b16.1 4 21 c.i. sluice / gate valve (flanged type) 150nb, class# 150 flange:ansi125 b16.1 4 22 stop cock 25nb (2 way, threaded end) casting: 100% virgin brass ingots certified for 63% copper to ensure flawless casting, chrome plated 4 23 slip on forged steel flange 150nb, ansi b16.5, class#150 8 24 bolt & nut with washer m20 x 2.5 x 90 long (part thread hex. head) 32 25 pipe threading die with handle ratchet type die head of 1/2 , 3/4 and 1 4 26 pulleys (for v belt or flat belt) to fit on 50mm dia. shaft with key slot cast iron 2 27 v belt and flat belt to fit on pulley 2 page 4 of 10 28 packing gasket ptfe gasket roll small size 2 29 washer, clutch, keys, jib, cotter & circlip minimum 25mm size, carbon steel material 4 30 bearing different types each type of diameter 25mm (min.) 2 set 31 lifting sling 8mm nominal dia. single leg sling up to 800kg capacity 3 variations available: soft eyes each end, thimble eyes each end, masterlink c/w sling hook & catch 2m height of lift as standard up to 10m available bs en13414 1:2003 4 32 bearing extractor universal gear puller 2 or 3 jaws adjustable chrome plating to provide a reliable and effective rust and corrosion protection. drive screw is covered by black phosphating, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. 2 33 pulley extractor universal gear puller 2 or 3 jaws adjustable chrome plating to provide a reliable and effective rust and corrosion protection. drive screw is covered by black phosphating, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. 2 34 stake hatchet with leg. 300 x 200 x 20 mm material ss 4 35 stake grooving. 100 x 100 x 300 mm material ss 4 36 depth micrometer. 0 25 mm accuracy 0.01 mm with standard set of extension rods upto 200 mm measuring faces: carbide. 2 page 5 of 10 37 digital micrometer outside. 0 25 mm l.c. 0.001 mm.. • measuring faces: carbide. • supplied with a ratchet stop for constant measuring force. 2 38 digital vernier caliper 0 200 mm l.c. 0.01 mm (optional)• resolution*1 : 0.01 mm or 0.0005 in/0.01 mm • display*1 : lcd • scale type*1 : absolute electromagnetic induction linear encoder • max. response speed*1 : unlimited • battery: sr44 (1 pc), 938882, for initial operational checks (standard accessory) • battery life*1 : approx. 5 years under normal use • dust/water protection level*1 : ip67 (iec 60529)*3 *1 digimatic models *2 analog models *3 rustproofing shall be applied after use if caliper was in contact with coolant. 2 39 compressor unit suitable for pressure: 30 liter horizontal tank and 0.36 cfm @ 90 psi. 110 max psi provides plenty of power to tackle diy projects. operates on 220 volt single phase electricity.oiled pump for maintenance free ownership and strong, reliable motor output conveniently placed gauges are easy to read and this compressors compact design makes it easily portable suitable for tire and ball inflation, its also perfect for powering air brushes, air/ brad nailers, upholstery projects and more power : 2 hp, cylinder : 48x1 mm, speed : 2850 r/min, pressure : 8 bar, weight : 30 kg 2 40 pneumatic trainer kit, each consisting of the following matching components and accessories: 2 i. single acting cylinder max. stroke length 50 mm, bore dia 20 mm 2 ii. double acting cylinder max. stroke length 100 mm, bore dia 20 mm, magnetic type 2 iii. 3/2 way valve manually actuated, normally closed 2 page 6 of 10 iv. 3/2 way valve pneumatically actuated, spring return 4 v. one way flow control valve 2 vi. 5/2 way valve with manually operated switch 4 vii. 5/2 way valve pneumatically actuated, spring return 2 viii. 5/2 way pneumatic actuated valve double pilot 2 ix. 3/2 way roller lever valve direct actuation normally closed 4 x. shuttle valve 2 xi. two pressure valve 2 xii. pressure gauge 0 16 bar 2 xiii. manifold with self closing nrv, 6 way 2 xiv. pushbutton station for electrical signal input with 3 illuminated momentary contact switches (1 no + 1 nc) and 1 illuminated maintained contact switch (1 no + 1 nc), contact load 2a xv. relay station with 3 relays each with 4 contact sets (3no+1nc or change over type), 5 a 2 xvi. 3/2 way single solenoid valve with led 2 xvii. 5/2 way single solenoid valve with manual override and led 2 xviii. 5/2 way double solenoid valve with manual override and led 2 xix. power supply unit, input voltage 85 – 265 v ac, output voltage: 24 v dc, output current: max. 4.5 a, short circuit proof. 2 xx. profile plate anodised aluminium 1100x700 mm, with carriers, mounting frames and mounting accessories (to be fitted onto the pneumatic workstation) 2 41 pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 1) work table – size(approx.) l1200mmxw900mmxh900mm, with four castor wheels including two lockable wheels at the front side, (2) drawer – size (approx.) – l460mmxw495mm xh158mm each, and overall size of drawer unit (approx.) l470mmxw495mmxh825mm and (3) drawer slide height (approx.) 85mm. 2 42 carrier for mounting components, such as pb & relay boxes. 2 43 cut section model for pneumatic components 2 44 hydraulic trainer kit, each consisting of the following matching components and accessories: 2 page 8 of 10 i. hydraulic power pack with (1) external gear pump having a delivery rate of 2.5 lpm, (approx.) @ 1400 rpm operating pressure 60 bar, coupled to a single phase ac motor (230 v ac) having start capacitor and on/off switch and overload protection, (2) pressure relief valve adjustable from 0 – 60 bar, (3) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and p and t ports. 2 ii. pressure relief valve pilot operated 2 iii. drip tray, steel size 1160 mm x 760 mm. 2 iv. pressure gauge glycerin damped, indication range of: 0 – 100 bar 2 v. four way distributor with five ports, equipped with a pressure gauge 2 vi. double acting hydraulic cylinder with a control cam, piston diameter16 mm, piston rod diameter10 mm, stroke length 200 mm. 2 vii. suitable weight for vertical loading of hydraulic cylinder 2 viii. mounting kit for weight for realizing pulling and pushing load. 2 ix. 3/2 way directional control valve with hand lever actuation. 2 x. 4/2 way directional control valve with hand lever actuation. 2 page 9 of 10 xi. 4/3 way directional control valve closed centre position, with hand lever actuation. 2 xii. non return valve. 2 xiii. pilot operated check valve pilot to open. 2 xiv. one way flow control valve with integrated check valve. 2 xv. t connector with self sealing coupling nipples (2 nos.) and quick coupling socket (1 no.). 4 xvi. profile plate, anodised aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories (to be fitted onto the hydraulic workstation) 2 45 hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 1) work table – size(approx.) l1200mmxw900mmxh900mm, with four castor wheels including two lockable wheels at the front side, (2) drawer – size (approx.) – l460mmxw495mm xh158mm each, and overall size of drawer unit (approx.) l470mmxw495mmxh825mm and (3) drawer slide height (approx.) 85mm. 2 46 cut section models for hydraulic components etc ...

Due Date : January 14, 2022

Tender Value : ₹ 8.65 Lakhs

View Tender
50
Department Of Defence - Rajasthan

30057655 bids are invited for non skid floor tiles 2 x 2 ( pressed ceramic) non skid floor tiles 2 x 2 ( pressed ceramic) , ceramic wall tiles size 12 x 8 ceramic wall tiles size 12 x 8 , door with ms angle frame 1.2 m x 2.10 m with 19 mm plywood shutter & complete accessories (size of angle 35mm x 35mm x 5mm thick), (good quality) door with ms angle frame 1.2 m x 2.10 m with 19 mm plywood shutter & complete accessories (size of angle 35mm x 35mm x 5mm thick), (good quality) , steel window size 5 x 4 with ms angle frame double shutter 4 mm glass & wire mesh fitted (size of angle 30 mm x 30mm x 5mm thick) (good quality) steel window size 5 x 4 with ms angle frame double shutter 4 mm glass & wire mesh fitted (size of angle 30 mm x 30mm x 5mm thick) (good quality) , steel window size 4 x 3 with ms angle frame double shutter 4 mm glass & wire mesh fitted (size of angle 30 mm x 30mm x 5mm thick) (good quality) steel window size 4 x 3 with ms angle frame double shutter 4 mm glass & wire mesh fitted (size of angle 30 mm x 30mm x 5mm thick) (good quality) , pvc paneled door size 6 x 2, registered brand with aluminium frame, heavy duty pvc paneled door size 6 x 2, registered brand with aluminium frame, heavy duty , aluminium sliding door size 4 x 7 complete set with frame, heavy duty aluminium sliding door size 4 x 7 complete set with frame, heavy duty , aluminium sliding door size 5 6 x 7 with frame complete set, heavy duty aluminium sliding door size 5 6 x 7 with frame complete set, heavy duty , aluminium sliding door size 5 8 x 7 set with frame complete set, heavy duty aluminium sliding door size 5 8 x 7 set with frame complete set, heavy duty , aluminium sliding door size 3 x 7 with frame complete set, heavy duty aluminium sliding door size 3 x 7 with frame complete set, heavy duty , aluminium main door size 7 x 4 with frame complete set, heavy duty aluminium main door size 7 x 4 with frame complete set, heavy duty , wc indian type with complet...

Due Date : December 07, 2021

Tender Value : ₹ Ref. Documents

View Tender