Public Health Engineering Department - Rajasthan

39964049 tender for work under sanctioned mla lad makrana at buldako ki dhani village kalwa bada 1 construction of tube well up to 100 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, ( if required ) excluding cost of casing pipes, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended up to date ) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a through out bore as per nominal dia of casing pipe. 2 nominal bore 200 mm dia. 3 add 15% extra on above item ( item no 2.4.1 to 2.4.2 ) for drilling depth beyond 100 mtr and up to 200 mtr from ground level, rate shall be applicable for only extra depth beyond 100 mtr and up to 200 mtr. 4 development of tube well as per i.s.11189:1985 and is 2800 ( part i ) :1991 ( both amended upto date ) using suitable compressor to give sand free water for required yield of the gravel packed tw 5 labour charges for making slots on blank pipes made of erw ms black pipe isi marked of following sizes, the slotting should be as per is: 8110 2000 or as amended up to date 6 200 mm dia nominal bore of 5.4 mm thickness 7 supply of erw m.s. black casing pipe isi marked ( is : 4270 / 2001 ) or amended upto date of grade fe 410 of following sizes 8 200 mm dia nominal bore of 5.4 mm thickness and mass of tube 28.46 kg / m ) 9 providing & lowering in tubewell isi marked gi pipe b class as per is : 1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25 x 3 mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 10 50 mm dia 11 supply & fixing of isi marked three core pvc flat submersible cable as per is : 694:1990 ro amended upto date and conductor as per class 5 of is 8130:1980 including making connection etc. 12 3 core 6.0 mm2 13 supply, installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per is : 8034 2011 ( pump ) and is 9283 2013 ( motor ) or amended upto date of approved make of following duty condition with required accessories includig making connection suitable for tube well / dcb. the job includes lowering of motor pumps, installation of complete fitting& accessories, jointing of electrical cables upto switch board, testing of submersible pump sets and interconnection up to water mains, complete in all respect. 14 7.5 kw ( 10hp ) & head above 120 mtr 15 s&f ms clamps set of 50 mm x 6 mm flat form iron with nuts and bolts etc for holding the riser pipe assembly of submersible pumpset 16 supply and fixing of electric control feeder panel comprising of suitable rating mccb, fully automatic star delta starter, over load relya, ampere n meter with cts, volt meter, phase preventor, suitable starting copacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out form 18 guage ms sheet with powder coating. panel should be of minimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5m ) duly bolted / screwed with enclosure box having 4 legs, each legs length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete plat form. the size of cc plate form should be equal or bigger thatn the base size of panel having height of at least 200 mm from gound level. the panel should have opening of suitable size in fron of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply 17 above 10 hp and up to 15 hp 18 providing and fixing of double flanged, ci body, isi marked nrv of approved make of size 65 mm dia 19 supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug.200 mm dia 20 fabrication & fixing m.s.stand of specified class of angle iron l shaped of 50 mm size with four legs grouted by 300*300*300 mm cc block m 15 in the ground and all legs tied up with each other through same size of angle iron along with cross bars to support the bottom of 1000 ltr. / 2000 ltr. pvc tank complete in all respect 21 providing & fixing pump safety cage as per specifications or as directed by engineer in charge. 22 testing verticality of tube well by plumping system and yield test and draw down test by pumping system as per is : 2800 ( part ii ) 1979 as amended up to date...

North Western Railway - Rajasthan

39881185 supply of kit of modified gasket for air brake pipe flangekit of modified gasket for air brake pipe flange,kit of modified gasket for air brake pipe flange welded joint to drg. no. bknws/mech/2023/12 confirming to str 04 abr 02 [with amendment 6] rev. 1 of feb. 2007. kit consisting of two items [1]. gasket for 32 nb pipe 05 nos. and [2]. gasket for 20 nb pipe ? 07nos [ warranty period: 30 months after the date of delivery ] sse/air brake/ bikaner , rajasthan 800.00 set...

Public Health Engineering Department - Rajasthan

39864553 tender for supply and installation of submersible pump set and mono submersible pump set and panel at division bagidora supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with requiredaccessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , up to 5.5 kw ( 7.5 hp ) & head up to 120 mtr. , up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. , 7.5 kw ( 10 hp ) & head up to 120 mtr. , 7.5 kw ( 10 hp ) & head above 120 mtr. , 9.3 kw ( 12.5 hp ) & head up to 120 mtr. , 9.3kw ( 12.5 hp ) & head above 120 mtr. , 11 kw ( 15 hp ) & head up to 120 mtr. , 11 kw ( 15 hp ) & head above 120 mtr. , 13 kw ( 17.5 hp ) & head up to 120 mtr. , 13 kw ( 17.5 hp ) & head above 120 mtr. , 15 kw ( 20 hp ) and above, head up to 120 mtr. , 15 kw ( 20 hp ) and above, head above 120 mtr. , supply and fixing of electric feeder panel ( having projected canopy ) for submersible pump set single phase up to 5 hp, comprising of dol starter, mcb, indicating light, ammeter, volt meter, connection plate, condensers of approved make and the panel enclosureshould be made out from 18 gauge m.s. sheet with powder coating. panel size height 600 mm width 500 mm depth 250 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the operation of panel should be suitable for on 240 volt ac supply. , supply and fixing of electric control feeder panel comprising of suitable rating mccb, dol starter, overload relay, ampere meter, volt meter, phase preventer, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 300mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level.the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. , up to 5.00 hp , supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. thesize of cc platform should be equal or bigger than the base size of panel having height ofat least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. , above 5 hp and up to 10 hp , above 10 hp and up to 15 hp , above 15 hp and up to 20 hp , above 20 hp and up to 30 hp , supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. , 3 core 4.0 sq.mm , 3 core 6.0 sq.mm , 3 core 10.0 sq.mm , 3 core 16.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. , 10.0 sq.mm, 4 core , 16.0 sq.mm, 4 core , 25.0 sq.mm, 3.5 core , 35.0 sq.mm, 3.5 core , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. , supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. , 125 mm dia , 150 mm dia , 200 mm dia , 250 mm dia , providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. , 32 mm dia , 50 mm dia , 65 mm dia , 80mm dia...

Panchayat Raj Department - Rajasthan

39731938 pageal arrangement water well construction work aam guwad panchra alias ammarpura ; 1 construction of tube well from ground level & up to 100 mtr depth to accommodate housing and assembly pipe of following sizes in all type of alluvium strata unconsolidated formation such as pebbles, boulders etc. by percussion / rotary drilling method as per is:2800 part 1: 1991 and is:2800 part ii: 1979 ( both amended upto date ) and technical specifications, the work would be comleted after obtaining sand free water 2 add 15% extra on above item ( item no 2.1.1 to 2.1.3 ) for drilling depth beyond 100 mtr and upto 200 mtr, rate shall be applicable for only extra depth beyond 100 mtr and up to 200 mtr. 3 supply of erw m.s. black casing pipe isi marked ( is: 4270 / 2001 ) or amended up to date offollowing sizes 4 labour charges for making slots on blank pipes made of erw ms black pipe isi marked offollowing sizes, the slotting should be as per is:8110 1985. 5 supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended upto date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 6 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. 7 supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connectionetc. 8 supply &fixing xlpeinsulated / p.v.c.sheathedcableof1.1kvgradewithaluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refillingearth, compactionofearth, makingnecessaryconnection, testingetc.asrequired of size. 9 plateearthing asperis:3043withg.i.earthplateofsize600mmx 600mmx 6.0mmby embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories 10 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holdingthe riser pipe assembly of submersible pump set. 11 supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 12 providing and fixing double flange isi marked of 80 mm dia 13 rope for holding units 14 providing & lowering in tube well isi marked gi pipe medium duty ( b class ) , steel tube as peris:1239oramendeduptodateandzinccoatingasperis4736, threadedanddouble flanged ( welded ) onbothendsandtwonumber25x3mmmsflatweldedonbothends between pipe and flange rubber washer and nut bolts etc comlete in all respect 15 display board 16 between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 80mm dia...

Rajasthan State Road Transport Corporation - Rajasthan

39438849 rsrtc invites the tender for automotive gasket essential , auto motive gasket (essential)as:284:71:dec:2006 , pgk/12 2576 3560 5301 gasket ( cover to hub) bs iv/bs iii,2017 , pgk/15 2573 3511 5302 gasket bs iii( diff. cover) , pgk/29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk/42 f1761300 gasket nozzle holder bs iii , pgk/47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk/65 ia 203036 rear axle packing eicher midi 1mm caf , pgk/66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv/iii/2017/ , 2786 1899 9910 gasket lube cooler bs iv/iii/2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii/iv , 252514115314 gasket egr cooler , 252514115313 gasket egr pipe flange , 252501155355 gasket arm cover , 278614999902 gasket turbocharger bsiv...

Rajasthan State Road Transport Corporation - Rajasthan

38739639 rsrtc invites the tender for automotive gasket essential , auto motive gasket (essential)as:284:71:dec:2006 , pgk/12 2576 3560 5301 gasket ( cover to hub) bs iv/bs iii,2017 , pgk/15 2573 3511 5302 gasket bs iii( diff. cover) , pgk/29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk/42 f1761300 gasket nozzle holder bs iii , pgk/47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk/65 ia 203036 rear axle packing eicher midi 1mm caf , pgk/66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv/iii/2017/ , 2786 1899 9910 gasket lube cooler bs iv/iii/2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii/iv...

Indian Army - Rajasthan

38655042 bids are invited for field water supply scheme mild steel casing pipe slotted 8 inch dia 5mm thickness 20 foot long , mild steel casing pipe unslotted 8 inch dia 5mm thickness 20 foot long , pea gravel of size 1 point 6mm to 4mm all around the casing pipe and slotted pipe in the well bore to entire depth complete , 80mm bore gi pipe medium grade isi marked with flanged fitting 20 foot long , 80mm bore gi pipe medium grade isi marked with flanged fitting 10 foot long , submersible pumping set 35 hp make kirlosakar or crompton or cri of capacity 1000 lpm at min 100 meter head and 200 lpm at 229 meter head , lt panel board outdoor cpri type tested made out of 3mm crca sheet cubical totally enclosed with hinges double door , welding rod the diameter can be 2 point 5 cmm 3 point 2mm 4mm and 5mm , hdpe coated plastic sheet 15 foot x 15 foot of minimum 250 gsm isi marked , nut and bolts appropriate size suitable for 80mm dia gi pipe flange , gi clamps for 80mm dia gi pipe , gun metal gate valve of 80mm dia with iron wheel head screwed both ends for gi pipe incl fittings ie union socket make leader or hm or zoloto , earth continuity conductor or main earting lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit or pipe or fixed to poles total quantity : 1430...

Rajasthan State Road Transport Corporation - Rajasthan

38311869 rsrtc invites the tender for exclusive parts tata through single source procurement , exclusive items ( tata ) , 2724 2540 8601collector ring , 2786 1599 9902tensioner belt , 2786 2099 9925thermostate tc , 2786 0198 9924tube inj. fuel supply 1, 2, 3 , 2786 0198 9925tube inj. fuel supply 4, 5, 6 , 2786 1899 9905core cooler , 2786 2099 9973thermostate bs iii , 2786 0599 9978tappit valve , 2786 0599 9969valve intake , 2786 0599 9004 / 9968valve exh. , 2786 0599 9912support cam shaft , 2786 1899 9933oil pump , 2786 0599 9977 / 7902cam shaft , 2786 0199 9946 hose plain , 2786 0199 9910plug expension , 2786 0199 9907plug expension , 2786 0599 9979push rod , 2786 0599 9981assy rocker lever , 2786 2099 9996clutch viscus fan , 2786 0798 9922timing plate , 2778 3210 3702front spring bracket frt. rh , 2754 2560 5101clutch release yoke , 2786 0399 9972fly wheel housing , 2770 312 00115engine cross member frt. , 2770 312 00113engine cross member rear , 2786 2099 9937 / 96fan engine , 2573 3120 8216cross member , 2786 0399 9907sleeve wear , 2778 3210 3701front spring bracketfrt. lh , 2778 3210 3703front spring bracket rear lh , 2778 3210 3704frt spring bracket rear rh , 2778 3210 7701webeller rubber front spring , 2786 0199 9802main brg. 2nd tc , 2786 0399 0106main brg. 3rd tc , 8854 0302 1618engine overhauling kit , 2786 0799 6901 / 2786 0798 9949tube fuel drain , 2754 2510 3401clutch housing bush , 2786 0599 9970collect valve , 2786 0399 0196flywheel , 2786 0399 9911flywheel washer , 2786 0599 9971 / 9901retainer valve , 2786 1899 9944 / 9922plug expension , 2786 0399 9980 / 5701 0399 0105con. rod bearing std. , npncon. rod bearing rs i , npncon. rod bearing rs ii , 2786 0199 9801 / 2786 0399 0176main bearing tc std. , npnmain bearing tc rs i. , npnmain bearing tc rs ii. , 2786 0599 9980cross head valve , 2076 5000 0201radiator , 2786 0199 9916cylinder liner tata , 2527 0110 3727cylinder liner tata midi , 2786 0999 9921hose plain a / b type , 2576 2410 0101frt. engine mtg. pad tata , 2576 2420 0118rr. engine mtg. pad tata , 2576 4130 6301p.s. rubber pad , 2641 2410 0109engine mtg. pad frt. rh tata midi , 2641 2410 0110engine mtg. pad frt. lh tata midi , 2573 4130 7505c.b. rubber tata midi , 2786 5010 5819hose rubber radiator , 2786 5010 5840hose radiator , 2786 5010 5835hose radiator , 2786 0399 0150 piston set bare std. , 2786 0399 0153piston ring set std. , 2786 0399 0151 piston set bare rs i , 2786 0399 0154piston ring set rs i , 2576 4130 3301c.b. bracket , 2076 5010 0152radiator assly. , 2786 5010 0375 / 0337raiator assly. , 2786 5010 0301 / 0286reserve tank plastic , 2575 3570 7902rr. axle shaft , 2527 0399 0172piston set bare std. tata midi , 2527 0399 0173piston ring set tata midi , 2575 3530 5403 / 5405rr. axle shaft gear gbs 60 , 2575 3530 5101diff. spidergbs 60 , 2691 2625 3704gear box frt cover upper gbs 60 , 2691 2630 3703g.b.frt.cover lower gbs 60 , 2691 2620 7911main shaft gbs 60 , 2691 2620 4615 engaging sleeve gbs 60 , 2691 26200185gear 2nd speed gbs 60 , 2691 26200184 geat ist speed gbs 60 , 2691 26204616 / 4624engaging gear reverse gbs 60 , 2691 2620 3710 rear cover main shaft gbs 60 , 2691 2630 3702 rear cover counter shaft gbs 60 , 2691 26208203oil slinger gbs 60 , 2691 2651 6705doweling pin gbs 60 , 2507 2670 9902brass pad gbs 60 , 2691 2620 8612spacer gbs 60 , 2516 2635 6102th. washer gbs 60 , 2691 2651 9901brass pad gbs 60 , 2691 2625 0135drive shaftgbs 60 , 2691 2630 7904 / 09counter shaft gbs 60 , 2691 2625 0126drive shaftgbs 60 , 2691 2630 5423constantmesh gear gbs 60 , 2691 2620 0182syncro. kit gbs 60 , 2688 2620 4608shifter sleevegbs 60 , 2691 2630 54105th gear on c / shaft gbs 60 , 2691 2620 0186gear 3rd speed gbs 60 , 2691 2620 0187gear 4th speed gbs 60 , 2691 2620 0189gear 5th speed gbs 60 , 2691 2620 4640engaging gear 5th&7th gbs 60 , 2691 2620 4651syncro. conegbs 60 , 2691 2620 4621engaging gear gbs 60 , 2691 2620 4618shifter sleevegbs 60 , 2691 2620 4650syncro. conegbs 60 , 2691 2620 5413gear reverse gbs 60 , 2691 2630 5424c / shaft third gear gbs 60 , 2691 2630 5425c / shaft fourth gear gbs 60 , 2688 2620 5407speed drive gear gbs 60 , 2691 2620 8601spacer gbs 60 , 2515 2620 4312 circlip gbs 60 , 2691 2620 4306circlip gbs 60 , 2691 2620 4301circlip gbs 60 , 2691 2620 4313circlip gbs 60 , 2691 2620 8629spacer main shaft gbs 60 , 2691 2651 8703compression spring gbs 60 , 2691 2625 8205oil slinger gbs 60 , 2668 3530 0107 / 0130c.w. & pinion set gbs 60 , 2688 2620 6501lock nut gbs 60 , 2691 2620 0172assly.coupling flange gbs 60 , 2691 2625 3113roller set gbs 60 , 2668 3530 5439gear rear axle shaft gbs 60 , 2691 2620 0146assly. over drive gear , 2691 2630 5414over drive gear , 2691 2651 5125shifter fork , 2691 2620 4652clutch body , 2691 2620 4643clutch body , 2691 2620 46444th spd. synchro cone , 2691 2620 4624engine gear reverse , 2516 2678 8201cap selector shaft , 2691 2620 4605clutch body d / shaft , 8854 2601 2516detent pin kit , 2691 2651 7507shifter fork , 2691 2620 4645syn. cone , 2691 2620 4623syn. cone , 2691 2620 4635syn. cone , 2691 2620 3426speedo adaptor ( rear cover upper ) 2017 model , 2691 2620 7910speedo pinion ( rear cover upper ) , 2691 2620 8203oil slinger ( rear cover ) , 2516 2671 3705gear case cover top ( upper half ) , 2691 2670 7903selector & shifter shaft rhd , 2691 2671 5101shifter finger , 2691 2671 8702compression spring inner , 2691 2671 8701compression spring outer , 2505 2670 6009shifting lever , 2691 2651 7907shifter shaft 5th / 6th , 2691 2651 5123shifter dog finger 5th / 6th , 2691 2651 5120swing fork 5th / o.d. , 2691 2651 9901brass pad , 2691 2651 7910shifter shaft 3rd / 4th , 2691 2651 5116shifter dog 3rd / 4th , 2691 2651 7908shifter shaft 1st / 2nd , 2691 2651 5115shifter dog 1st / 2nd , 2691 2651 7918shifter shaft reverse speed , 2691 2651 5118shifter dog reverse , 2691 2651 5113shifter fork reverse , 2574 4910 0110silencer muffler, tata , 2786 0599 9966inlet valve bs iii , 2651 3210 6704frt. spg. shackle pin , 2651 3240 3401frt. spring bush , 2640 3240 6702rr. spring shackle pin , 2640 3240 3401rear spring bush , 2643 3220 4201frt. spring u bolt , 2644 3250 4203rr. spring u bolt , 1205 239 6067nut for u bolt , 1205 239 6075nut for u bolt , 2821 3320 6701king pin std , 8854 3319 0709king pin kit std. , 2641 4010 6703wheel bolt , 1205 169 6059wheel nut , 5507 4010 6702rear wheel bolt , 2525 2010 0124assy. water pump , 2525 2010 0119water pump repair kit major , 2641 3320 0121tie rod , 2641 3320 0135assy ball joint lh , 2641 3220 0136assy ball joint rh , 2651 3320 6304dust cap tie rod , 2651 4110 0128u.j.cross kit , 2632 4370 0115frt. brake diaphragm , 2821 4210 3702rear brake drum , 2574 3340 3701hub cover front , 2763 2540 0102310 dia assy. pressure plate , 2527 2311 0103steering oil pump midi , 2654 4620 8711compressor spring for stg. , 2641 4621 0136power stg. gear box rep. kit major , 2651 4660 0102u.j.cross stg. , 2786 0999 9951diesel fuel stainer , 2527 0100 0368engine assly. complete , 2786 0399 0176con. rod brg. std. , 2641 2910 0189brake pedal assly. , 2527 0312 3119main brg. set , 8854 0343 2534con. rod brg. std. , 2534 2015 6323cogged belt 980 length , 2534 2010 6310v. belt ( cogged ) 925 , 2525 2015 6305fan belt , 2640 3210 0105assly. shackle with bush , 2527 1451 0120turbocharger assly. , 2527 5011 0130radiator assly. , 2661 3570 7903rear axle shaft , 2770 0100 0102engine assly. complete , 2691 2601 0155gear box assly. gb 60 , 2691 2601 0150gear box assly. gb 60 ( over drive ) , 2778 3300 0101frt. axle assly. tata , 2668 3500 0205rear axle assly. tata , 2786 0199 0311short block w / o cyl. head ( with internal fitting ) , 2786 0199 0110cylinder block , 2651 3210 6704frt. spg. shackle pin , 2651 3240 3401frt. spring bush , 2640 3240 6702rr. spring shackle pin , 2640 3240 3401rear spring bush , 2525 2010 0124assy. water pump , 2525 2010 0119water pump repair kit major , 2574 3340 3701hub cover front , 2763 2540 0102310 dia assy. pressure plate , 2654 4620 8711compressor spring for stg. , 2651 4660 0102u.j.cross stg. , 2786 0999 9951diesel fuel stainer , 2527 0100 0368engine assly. complete , 2786 0399 0176con. rod brg. std. , 2641 2910 0189brake pedal assly. , 2527 0312 3119main brg. set , 8854 0343 2534con. rod brg. std. , 2640 3210 0105assly. shackle with bush , 2527 0399 0172piston set std , 2527 0399 0173piston ring set std , 2527 5011 0130radiator assly. , 2661 3570 7903rear axle shaft , 2786 0199 9902bush cam shaft , 2786 0399 3401con. rod bush , 2786 1499 9942exh. manifold clip , 2507 2670 0152sub assy ball socket , 2848 2910 0122cmc steel pipe , 2770 2681 0101gear lever stand , 2786 1399 9904con. rod bearing set , 2651 4660 3401needle bush rs 1 , 8854 0358 2527piston set tata midi , 8854 0360 2527 piston ring set tata midi , 2632 5420 9903tempreture switch , 2654 5450 9913oil pressure switch , npnrecone engine assy tata bs iii , 2691 2625 3105cylinder roller bearing , 2691 2620 3120needle cage double row bearings , 2691 2620 3106needle cage rev. gear bearings , 2691 2620 3103tapper roller bearings , 2691 2620 7814g b oil seals , 2691 2625 3113roller thrust bearings , 2651 3530 7701oil sel tp , 2691 2620 0143assy neddle cage bearings , 805345 / gb 356437fan support bearings , 2786 2099 0153water pump assy bs iii , 2525 2010 0124water pump assy midi , 2691 2630 54136th counter gear over drive , 2691 2651 7918shifter shaft reverse , 2786 0199 9905plug expension , 2691 2651 7907shifter shaft 5& 6 , 2576 3340 3104 / 3101front huib inner bearing , 2573 3530 3109 / 0009818601 / nu 307mnwtail pinion bearing , 2691 2620 0142neddle cage bearing , 2691 2630 3104tapper roller bearings , 2676 3320 3109king thrust bearing t151 , 2690 2620 3106 / 3131needle cage bearing 1st , 5812 2560 1602clutch release bearing , 2574 4100 0000centre bearing tata midi , 2516 2635 3104roller ring , 2525 0161 0173assy. engine complete bs iv , 2525 0199 0262assy. long block bs iv , 2525 0199 0264assy. half block bs iv , 2525 0199 0266engn. over haul gasket kit bs iv , 2525 0199 0267decarbonising gasket kit , 2525 0110 0313cylinder block assy.w / o clutch housing , 2525 0115 5336gasket , 2525 0115 5355gasket rocker arm cover , 2525 0114 6301gasket , 8854 0504 2525cam shaft bearing set , 8854 0398 2525set inlet & exh. valve , 2534 0515 3402valve guide inlet std , 8854 0397 2525valve seat ring std , 2534 0515 3415valve guide exh. std , 2525 0114 0186assy. timing gear hsg. , 2534 0310 7801oil seal crank shaft frt. , 2525 2510 3745clutch housing , 2525 0311 8203back cover , 2525 0311 8204cover , 5710 1520 9903cam sensor , 5710 1520 9902crank sensor / speed sensor , 2525 0311 0141assy. fly wheel with ring gear , 352 032 1105ring gear , 2525 0310 7940crank shaft , 3520 520 003crank shaft gear , 2525 0313 8201oil slinger , 2525 0313 8603spacer , 8854 0308 2525kit crank shaft sealing ring , 2525 0312 0159set main bearing , 8854 0376 2525thrust washer set std , 8854 0377 2525thrust washer set rs i , 8854 0378 2525thrust washer set rs ii , 2525 0399 0165set con rod bearing std , 8854 0368 2525con rod bush set std , 2525 0399 0197piston set bare std , 2525 0399 0188piston ring set std , 2534 0310 3102ball bearing , 2525 0510 0145assy. cam shaft with cyl. pin , 3520 520 762thrust washer , 2525 0713 0123assy. cam shaft gear & drive gear , 2534 0513 9902tappet valve , 3520 540 205valve push rod inlet & exh. , 2525 0712 5302gasket , 2527 0911 0136protect filter , 2525 1451 0145assy. turbo charger , 2525 1411 5301gasket , 2525 1412 3703exh. manifold cowl , 2525 1411 0136assy. gasket exh. manifold , 2525 1411 0135assy. gasket exh. manifold , 2525 1410 0101assy. gasket intake manifold , 2525 1411 0235assy. egr cooler , 2525 1411 5314gasket , 2525 1411 0281assy. egr valve 24 v , 2525 1470 0167assy. inlet line , 2525 1514 6303poly v belt 1260l , 5033 5420 9904ems ecu for 697 dicor engn. , 2525 1810 0148assy. oil pump with strainer , 2525 1810 0144assy. oil pump w / o strainer , 2525 1810 3704housing , 2525 1810 7902drive shaft oil pump , 2525 1810 5405drive shaft ( 50mm ) , 2525 1810 7901shaft for drive gear , 3521 840 329valve hsg. , 2525 1815 0140assy. strainer , 3121 860 080gasket , 8854 1808 2525gear kit oil pump , 8854 1804 2525oil pressure relief valve kit , 2525 1813 0166assy. oil filter head , 2654 5450 9913low oil pressure switch , 2534 1813 5301gasket , 2525 1817 0232assy. oil cooler , 2525 1817 0150assy. relief valve , 2525 2010 0180assy. water pump , 2527 2010 5310w. p. gasket , 2525 2014 0153assy. viscous fan 550 dia , 2525 2014 7028water pump pulley , 2525 2012 0248assy. thermostate 35 dia , 2525 2314 6313v belt coggerd 1060l , 2618 4660 0101power steering pump assy. , 2525 2311 0122assy. bracket , 2525 2340 7006pulley , 2525 2314 6316v belt coggerd 995l , 2724 2520 0151clutch plate 330 dia , 2724 2540 0143clutch cover assy. 330 dia , 2724 2560 0160assy. clutch release bearing , 2724 2560 5106clutch release fork , 2724 2560 0115assy. bracket out side rh , 2505 2605 0154gear box assy. gbs 40 , 2505 2610 3723gear box housing , 2505 3014 5301gasket frt. cover lower , 2505 2630 8201housing cover frt. lower , 2505 2625 5301gasket frt cover top to hsg. , 2505 3013 4701gear box hsg. cover frt. top , 2505 2625 7808oil seal drive shaft , 2505 2620 7803oil seal , 2668 3515 0102pressure relief valve , 2505 2670 5105shifter fork ist speed , 1595 3520 131needle roller bearing 2x13.8 , 321 265 0805selector shaft ist speed , 321 265 1805selector shaft 2 / 3rd speed , 321 265 1905selector shaft 4 / 5th speed , 322 265 0305selector shaft reverse , 322 265 0123gear shift dog 1st gear , 321 265 1205selector fork 2 / 3rd , 2505 2651 5102selector fork 4 / 5th , 321 265 1301selector fork 1st , 2505 2651 5101selector fork reverse , 2505 2671 3756top cover , 2507 2671 3105needle bearing , 2505 2670 5104shifter finger , 2505 2670 7908selector & shifter shaft , 1706 160 2518oil seal , 2507 2670 6014shifting lever , 2506 2671 5301gasket kit , 2505 2600 0101kit gasket gear box , 2505 2625 7910drive shaft , 000 981 1201cylinder roller bearing nu 309n , 2505 2620 3106four point ball bearing , 2505 2625 3118roller cage , 2505 2620 7903main shaft pilot bearing , 340 262 0134syn. ring , 2505 3015 5403syn. sleeve 4 & 5th , 2505 2620 3802syn. cone , 321 262 0823shifting sleeve , 2505 3015 0105assy. helical gear 4th speed , 2505 2620 3123double row needle cage , 2505 2620 3124double row needle cage , 322 260 0644assy. helical gear 3rd , 322 262 0435syn. sleeve 2 / 3rd , 322 262 0112helical gear 2nd ( t 32 ) , 322 263 0333reverse gear main shaft 36t , 321 262 0723shifter sleeve 1st , 2505 3015 5401gear wheel 1st speed t 39 , 2505 2620 0176gear drive oil slinger , 2505 2620 7902drive shaft , 2507 2620 5001coupling flange ( 8 holes ) , 2505 2630 7906counter shaft , 2505 2630 54142nd gear counter shaft , 2505 2630 54153rd gear counter shaft 23t , 2505 3014 54014th gear on counter shaft , 2505 3014 5402constent mesh gear , 2505 2630 3104tapper roller bearing , 2505 2635 0106assy. reverse idler gear ( en 36 ) , 2505 3017 7901reverse idler gear shaft , 8854 2604 1612syn. kit , 2165 2680 0111assy. self & shifter yoke & fork , 2651 4660 3401needle bush , 2630 2680 8601spacer , 2641 2680 0224assy. ball joint rh , 2641 2680 0225assy. ball joint lh , 2641 2910 0117cmc assy. ( 19.05 dia ) , 2724 2560 5106clutch release fork , 302 991 0015ball pin , 2699 2910 0177cmc repair kit major , 2651 29100148cmc repair kit minor , 2754 32103201frt. center bolt , 1205 150 1207nut center bolt m12 , 352 320 0063frt. spring shackle , 2770 3210 3401frt. spring bush , 352 322 0530frt. spring pin , 2573 3210 6701frt. spring pin , 2573 3210 0107assy. sealing ring , 042 990 0037jcotter pin , 2770 3220 4203u bolt l 280 , 2618 3240 3202rear center bolt , 352 320 0163rear spring shackle , 2770 3240 3402rear spring bush , 352 325 0530rear shackle pin , 2575 3320 3401king pin bush , 2575 3320 9203 thrust washer upper , 2575 3320 9207thrust washer lower , 2846 3320 3101tapper roller th. bearing , 2576 3320 6707king pin cotter pin , 2632 3340 0104frt. hub assy. , 2576 3340 3103tapper roller bearing outer , 2576 3340 3101tapper roller bearing inner , 5030 3340 7801oil seal , 2631 4010 6701frt. wheel bolt m 22 , 2776 4210 3703frt. brake drum , 8854 3316 1612king pin repair kit minor std , 8854 3301 1612king pin repair kit minor 1st o / s , 8854 3302 1612king pin repair kit minor 2ndo / s , 8854 3303 1612king pin repair kit minor 3rdo / s , 5014 4210 9902kit cam end spring , 2880 4210 6701fulcrum pin , 5006 4210 0155front brake shoe assy. , 2573 4211 3210frt. mtg. bolt , 5014 4210 5101cam shaft lh , 5014 4210 5102cam shaft rh , 8854 4201 1512front brake lining set std. ( set of 8 pcs. ) , 8854 4202 1512front brake lining set 1st o / s ( set of 8 pcs. ) , 8854 4203 1512front brake lining set 2nd o / s ( set of 8 pcs. ) , 8854 4219 0709brass rivet long ( set of 48 nos. ) , 8854 4220 0709alluminium rivet long ( set of 48 nos. ) , 8854 4204 1512rear brake lining set std. ( set of 8 pcs. ) , 8854 4205 1512rear brake lining set 1st o / s ( set of 8 pcs. ) , 8854 4206 1512rear brake lining set 2nd o / s ( set of 8 pcs. ) , 2631 4020 6701rear wheel bolt m22 , 3668 3560 7703oil seal double , 2576 3560 3101tapper roller bearing inner rear , 2575 3560 3110tapper roller bearing outer rear , 2776 4230 3714rear brake drum , 2575 3570 7902rear axle shaft , 2576 3560 5301gasket , 2575 3530 5101differential spider , 2668 3530 5440diff. bavel pinion , 2575 3530 9201spherical washer , 2575 3530 3102tapper roller bearing , 2668 3530 0233c.w. & pinion assy. , 2573 3530 3109cylindrical roller bearing , 2060 3501 3001tapper roller bearing , 2668 3530 6501threaded ring , 2732 3530 0187assy. coupling flange 130dia , 2574 3315 0102breather assy. , 2776 4299 0109rear brake shoe assy. , 2776 4230 5102rear cam shaft lh , 2776 4230 5103rear cam shaft rh , 2880 4210 3403bush , 5040 4230 9909kit roller , 2631 4010 0107assy. wheel nut m 22 , 2750 4111 5101flange yoke , 2750 4130 0101center bearing kit , 2750 4130 3322center bearing bracket , 2632 4111 6301center bearing rubber , 2750 4111 5102companion flange , 2778 4230 0190automatic slack adjuster , 2776 4230 0230auto. slack adjuster rear lh , 2776 4230 0231auto. slack adjuster rear rh , 2778 4230 0165major repair kit slack adjuster , 2651 4660 0102assy. universal joint , 2063 4630 5104pitman arm , 2632 4600 0103drag link assy. , 2618 4660 0110seal kit , npnpiston set bare rs 1 , npnpiston set bare rs 2 , npnpiston ring set rs 1 , npnpiston ring set rs 2 , 2618 3240 0107rear main leaf , 2618 3240 7127rear 2nd leaf , 2618 3240 7128rear 3rd leaf , 2618 3240 7129rear 4thleaf , 2618 3240 7130rear 5th leaf , 2618 3240 7131rear 6th leaf , 2618 3240 7132rear 7th leaf , 2618 3240 7133rear 8th leaf , 2618 3210 0109front main leaf , 2618 3210 7111front 2nd leaf , 2618 3210 7112front 3rd leaf , 2618 3210 7113front 4thleaf , 2618 3210 7114front 5th leaf , 2618 3210 7115front 6th leaf , 2618 3210 7116front 7th leaf , 2618 3210 7117front 8th leaf , 2632 4210 3403sensor bush abs , 2643 5420 9929sensor l type frt. ( wheel speed ) , 2808 4210 3401sensor sleeve frt. , 2808 4230 3301sensor axle bracket rear , 2808 4230 3303sensor mounting bracket rear , 2163 5462 0221wiring harness battery cut off switch , 2165 5462 0101wiring harness sensor , 2165 5462 0102wiring harness engine for egr , 2165 5462 0110wiring harness dps inter connection , 2165 5462 0114main wiring harness , 2780 5420 9938speed sensor 12v / 24v , 2816 5421 0125ecu abs8, 4s / 4m 24v , 2525 0911 9903temperature sensor , 2525 1520 9901boost pressure sensor , 2525 1520 9905hfm sensor , 2527 0911 9911water level sensor , 2527 0911 9912temperature sensor , 2641 5420 9962water temperature sensor , 2525 1520 9906dps sensor , 2632 4210 3403sensor bush abs , 2782 4210 0106brake chamber type 24 , 2632 3910 0174repair kit brake chamber type 24 , 2752 4370 0108spring brake actuator type 24 / 24 , 5042 4399 0105spring brake actuator t24 / 24 major , 2778 4370 0165air dryer 9 bar osc cartridge , 5053 43900176air dryer cartridge , 2632 4371 0102repair kit air dryer , 2632 43700142four circuit prot. valve , 2632 4370 0104major repair kit four circuit prot. valve , 2632 4371 0145minor repair kit four circuit prot. valve , 2880 4370 0194rg2 relay valve , 2782 4370 0189repair kit relay valve , 2846 4371 0109dual treadle valve , 2632 4391 0168repair kit dual brake valve , 2163 4370 00252quick release valve , 4103 4370 9910repair kit quick release valve , 2770 3010 0138accelerator cable assy. , 5028 3010 0106assy. pull cable accelerator , 2525 1810 0148assy. oil pump with strainer , 2525 1810 0144assy. oil pump without strainer , 2786 0799 6905tube fuel supply bs iii 2017 model , 2786 0799 6901tube fuel drain bs iii 2017 model , 2786 0799 6904tube fuel supply bs iii 2017 model , 2523 0117 6937tube bs iii , 2525 0714 0204assy. fuel pressure line 1 ( bent ) fip , 2525 0714 0243assy. fuel pressure line 1 ( bent ) rail to inject , 2525 0714 0205assy. fuel pressure line 2 ( bent ) fip , 2525 0714 0244assy. fuel pressure line 2 ( bent ) rail to inject , 2525 0714 0245assy. fuel pressure line 3 ( bent ) rail to inject , 2525 0714 0246assy. fuel pressure line 4 ( bent ) rail to inject , 2525 0714 0247assy. fuel pressure line 5 ( bent ) rail to inject , 2525 0714 0248assy. fuel pressure line 6 ( bent ) rail to inject , 2525 0912 0307assy. over flow line rail to accumulator , 2525 0912 0306assy. over flow line pump to accumulator , 2525 1817 0205assy. lube line flexible , 2525 1813 0162assy. oil line oil filter to fip , 2527 1817 0128assy. lube line oil filter to fip , 2651 4660 0102assy. universal joint bs iii / iv , 2067 4660 0105assy. universal joint bs iii / iv , 2641 2680 0224assy. ball joint rh bs iii / iv , 2641 2680 0225assy. ball joint lh bs iii / iv , 2785 5010 5803hose ( 20idx110l ) bs iv , 2525 5010 5865hose water fill pipe ( 20idx90x105 ) , 2525 5011 5811hose radiatorto w.p. , 2525 5011 5857rubber hose ( th. to radiator ) , 2525 5011 5858vent hose ( radiator to th. ) , 2786 0599 9906hose plain bs iii , 2786 1899 5803hose elbow bs iii , 2525 0117 5809hose oil separator bs iv , 2786 0599 9967insert valve 2017 model , 5701 0599 9001valve exhaust , 5701 0599 8701spring valve , 2786 0599 9973seal valve steam , 2786 0599 4701cover valve , 2770 3230 0102assy. frt. shock absorber , 2574 4323 0104assy. bracket frt. shock absorber , 042 323 0063 jshock absorber mtg. bracket lower , 2574 3230 8602bush frt. shock absorber , 2786 2099 9995fan engine 2017 model , 2076 0101 0109engine assy. complete bs iii 2017 model , 2786 0199 0212long block bs iii 2017 model , 2786 0199 9906plug expansion , 2786 0199 9915plug expansion , 2786 0599 9937plug expansion , 2786 0198 9911plug expansion , 2863 0199 9922plug expansion , 2786 0599 0108housing gear , 2786 0399 5402gear fly wheel ring , 2786 2099 9828thermostat , 2505 2605 0154assy. gear box gb 40 bs iv , 2505 2610 3727gear box housing bs iv , 2691 2610 0167assy. housing rear & front half 2017 model , 2163 3300 0112front axle assy. 2017 model , 2668 3500 0282rear axle assy. with brake , 3163 3300 0114front axle assy. bs iv , 2668 3500 0276rear axle assy. complete bs iv , 2599 3250 4201u clamp rear , 2525 1460 5822hose ( tc adapter to pipe ) , 2632 2420 0103assy. rubber support rear rh , 2632 2420 0104assy. rubber support rear lh , 2786 1499 9931clamp v band , 3522 420 509torque support front , 1428 059 6044hose clamp , 2525 1460 5823assy. hose hump , 1428 059 8233hose clamp , 2525 0914 0190assy. pipe with flange , 2525 0914 5867hose ( air filter to air intake pipe ) , 2525 0914 5869hose ( hfm sensor to air intake pipe ) , 2525 5000 0284assy. bracket , 1650 080 2603elbow , 2786 0913 0352assy. air filter mtg. bkt. , 2849 3010 0101assy. bracket , 5027 2910 0116assy. hydraulic pipe , 5027 2910 7501rubber grommet , 1428 059 8209hose clamp , 2806 5420 0113assy. bracket , 2592 6890 6302nacelle top , 2525 1913 0162assy. oil line , 2525 2314 5810rubber hose ( ac to egr outline ) , 2547 0913 9918service indicator , 2525 0117 0310assy. oil dipstick complete , 2525 0914 0219air intake pipe , 2786 0913 9918adapter , 5027 4680 0105assy. peass. pipe pump to gb , 2786 0913 0297assy. astrap with shackle , 2525 2012 5841rubber hose ( ucwl to thermostat ) , 2525 2012 5842rubber hose , 2525 1460 6967pipe ( tc adapter to ic ) , 1428 0599 9272hose clamp , 2525 1313 0159assy. pipe with ferrule , 2786 1460 3822cast pipe on ic outlet , 2839 2910 0105assy. clutch fluid reserviore with clamp rh , 2165 2950 0101bracket for clutch booster mtg. , 5027 2910 0101assy. hydraulic pipe ( m. cyl. yo booster ) , 2165 2910 0118pipe assy. ( booster to m. cyl. ) , 2525 1460 0166tc adaptor , 2786 1460 5802hose clamp , 2525 0914 3863air intake pipe ( hfm sensor to tc ) , 2785 0913 9901rubber strap , 1428 050 0209hose clamp , 2782 5460 0108assy. clamp , 2846 2950 8201bracket on lm , 2699 3010 0138assy. accelerator pedal complete , 5027 4680 0107assy. suction pipe ( tank to pump ) , 2525 5000 0247bracket on lm rad frame side mtg. , 2574 5000 6904spacer tube , 2763 2680 7901link rod , 2525 0914 5856hose ( air intake to tc ) , 2576 2410 9201washer , 2641 4310 6801pipe union bolt , 2525 5000 0240assy. bracket rh , 2786 5000 0250assy. rubber bush rad frame side mtg. , 2574 5000 9202washer , 2574 5000 6301rubber buffer , 2525 5000 0239assy. bracket lh , 2525 1460 6961pipe ( ic to intake elbow ) , 5027 4680 0106assy. return pipe , 2165 4390 0236pipe assy. metal , 2632 2420 0105assy. housing rh , 2632 2420 0106assy. housing lh , 2806 3120 0102assy. engine cross member front , 1428 059 9361hose clamp , 2786 1460 6910air intake pipe , 2786 1460 6906extruded pipe tc to ic , 2786 1460 3823cast pipe on ic , 2786 1460 3301bracket , 2786 1460 3302bracket , 2786 0913 0134assy. air filter , 2786 0913 6941aluminium pipe , 2525 0914 5804reducer hose , 2770 2410 5101engine mounting arm rh , 2770 2410 5102engine mounting arm lh , 5028 2420 7108spacer plate , 2163 2915 0102assy. tube , 2077 2915 0111assy. connecting line , 2782 2910 0128sub assy. clutch paddle plate , 2808 2910 0109assy. clutch paddle lever , 2846 4370 0162grad hand conroller valve , 2547 5010 4222hose clamp 50 dia , 2782 4440 0101assy. hydraulic stg. tank plastic , 2786 1460 9910intercooler , 2525 2314 0129assy. clutch fluid reserviore with clamp rh , 2691 2651 3402bush swing fork , 2808 4640 0101assy. steering wheel complete , 2525 1460 5814hose ( ic to intake elbow ) , 2525 1411 0337assy. egr pipe , 2632 3120 0123assy. support lh , 321 353 0025threaded ring , 2780 5450 6302carrier plate , 2527 1813 0132oil filter element , 2527 0312 0110set main brg. upper / kower normal , 2527 0310 0293assy. crank shaft , 2576 4900 7502rubber buffer , 2525 1411 0346assy. egr valve 24v , 2750 4610 0101assy. bracketstrg. gear box mtg. , 2786 0913 5838hose tc outlet , 2525 1411 5313gasket ( egr pipe flange to egr valve ) , 2165 3120 0117assy. bracket lh , 2165 2686 0101assy. bracket ( gear shift lever ) , 5533 5450 4903electrical battery cut off switch...

Public Health Engineering Department - Rajasthan

38237934 execution of sanction work at chandawal nagar for village atpara under sub. dn.sojat. ( as per phed bsr 2023 ) 1 construction of tube well after completion of drilling by rotary / percussion method & up to 100 mtr. depthin all type of rocks by dth systemas per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended up to date ) and technical specifications. the workshall be deemed completed only after obtaining sand free water. the bore well should have a throughout nominal size bore beyond casing pipe.nominal bore 200 mm dia. 2 nominal bore 200 mm dia.add 15% extra on above item ( item no 2.3.1 to 2.3.3 ) for drilling depth beyond 100 mtr and up to 200 mtr from ground level, rate shall be applicable for only extra depth beyond 100 mtr and up to 200 mtr. 3 supply of erw m.s. black casing pipe isi marked ( is: 4270 / 2001 ) or amended up to dateoffollowing sizes 200 mm dia nb ( thickness of pipe 5.4mm & mass of tube 28.46 kg / m ) 4 labour charges for making slots on blank pipes made of erw ms black pipe isi marked of following sizes, the slotting should be as per is:8110 1985. 200 mm dia nominal bore of 5.4mm thickness 5 supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 7.5 kw ( 10 hp ) & head above 120 mtr. 6 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply.above 5 hp and up to 10 hp 7 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 6.0 sq.mm 8 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.16.0 sq.mm, 4 core 9 plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. 10 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 11 supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug.200 mm dia 12 providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect.50 mm dia 13 providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended up to date of approved make including cost of all material andlabouras per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia.80 mm dia 14 maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log books & histroy sheetas directed by engineer in charge for tubewell per month. ( for urban water supply scheme ) 8.0 hp to 10 hp ( 3 years o&m ) 15 providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes65 mm dia...

North Western Railway - Rajasthan

37852068 supply of kit of gasket for air brake pipe flange welded joint to drg. no. wd 83062 s 07 with alt. 5.confirming to str 04 abr 02 [ with amendment 6 ] rev. 1 of feb. 2007. kit consisting of two items [ 1 ] . gasket for 32 nb pipe 05 nos. and [ 2 ] . gasket for 20 nb pipe 07 nos. [ warranty period: 30 months after the date of delivery ] => limited...

Rajasthan State Road Transport Corporation - Rajasthan

37518686 rsrtc invites the tender for supply of automotive gasket essential , auto motive gasket ( essential ) as:284:71:dec:2006 , pgk / 12 2576 3560 5301 gasket ( cover to hub ) bs iv / bs iii, 2017 , pgk / 15 2573 3511 5302 gasket bs iii ( diff. cover ) , pgk / 29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk / 42 f1761300 gasket nozzle holder bs iii , pgk / 47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk / 65 ia 203036 rear axle packing eicher midi 1mm caf , pgk / 66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold ) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv / iii / 2017 / , 2786 1899 9910 gasket lube cooler bs iv / iii / 2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii / iv...

Rajasthan State Road Transport Corporation - Rajasthan

36748215 rsrtc invintes the tender for supply of automotive gasket essential , auto motive gasket ( essential ) as:284:71:dec:2006 , pgk / 12 2576 3560 5301 gasket ( cover to hub ) bs iv / bs iii, 2017 , pgk / 15 2573 3511 5302 gasket bs iii ( diff. cover ) , pgk / 29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk / 42 f1761300 gasket nozzle holder bs iii , pgk / 47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk / 65 ia 203036 rear axle packing eicher midi 1mm caf , pgk / 66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold ) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv / iii / 2017 / , 2786 1899 9910 gasket lube cooler bs iv / iii / 2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii / iv...

Public Health Engineering Department - Rajasthan

36407810 work related to jal jeevan mission in village dhikali in block badgaon under suv div badgaon, udaipur including one year defect liability period under jjm tubewell 3 nos 2 construction of tube well up to 150 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soil & over burden including lowering of casing pipe, ( if required ) excluding cost of casing pipe, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a through out bore as per nominal dia of casing pipe. 3 nominal bore 200 mm dia. 4 add extra 15% 5 200 mm dia nb ( thickness of pipe 5.4mm & mass of tube 28.46 kg / m ) 6 supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 7 200 mm dia 8 rising pipe line 9 providing, lowering, laying in trenches, aligning, fixing in position and jointingductileiron ( di ) isi markedk 7grades&spipesas per is:8329 2000 ( amendedup todate ) , withinternalcementmortar lining suitable for potablewater with rubber ring ( epdm ) joints as per is: 5382 1985 including all taxes ( central and local ) , transportation and freight charges, inspection charges, loading / unloading charges, including cost of labour and material, specials ( tee, bend etc. ) satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge. ( excluding earth work ) note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 10 100 mm dia di k 7 pipe 11 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 12 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and stacking serviceable material for measurements and disposal of unserviceable material as directed, with in a lead of 50 mtr. including all safety provisions required .: 13 ordinary rock 14 hard rock ( requiring blasting ) 15 hard rock ( blasting prohibited ) 16 dismantling of cement concrete pavement for pipe line line and chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, re handling of material / earth to complete the tasks as per technical specification and scope of work. 17 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, complete work as per technical specification and scope of work. 18 m20 grade nominal mix1: 1.5: 3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) . 19 providing, lowering, aligning, fixing in position in pipe line at work site, di d / f resilient seated ( soft seated ) sluice valves ( gate valves ) , vacuum tight ( bubble tight ) , straight and pocket less body passage of approved make of following class & dia complete confirming to bs en 1171 / awwa c 509 and of following specifications: body & bonnet of ductile cast iron of grade ggg40 / ggg50 as per din 1693 or gr sg 400 / 12 as per is 1865 or equivalent grade as per is :3896 part2 1985 and subsequent revisions, wedge of same material as body & shall vulcanisedrubber lined with epdm ( food grade quality ) and seals of nbr face to face dimensions as per bs 5163 89 / is 14846 / 2000 ( amended up to date ) / din 3202 f4, stem / spindle of ss ( aisi 316 or equivalent ) electrostatic epoxy powder ( ep p ) / fusion bond epoxy ( non toxic suitable for drinking water ) coated with minimum thickness of 250 microns inside and outside, drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367 ( galvanised steel ) insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic, sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece / dismantling joints and earth work. 20 manually operated resilient seated sluice valves of class pn 1.0 / 1.6 21 100 mm dia 22 providing, lowering, aligning, fixing in position in pipe line, ci double flanged swing type non return valves ( nrv ) of approved make of following pressure rating & dia complete, confirming to is: 5312 ( part 1 ) / 2004 ( amendedup to date ) and of following specifications: body, cover & disc of grey cast iron of is:210 / fg200. face to face dimensions as per is 5312 ( part 1 ) :2004 , flanges drilled as per is:1538. epoxy ( non toxic & suitable for drinking water ) applied on body, cover and disc inside and outside . body seat ring of ss / cs door face ring epdm / neoprene ( food grade quality ) , shaft of htb1 / ss aisi 410 , hinge maleable cast iron / ss aisi 316 / 410 , bonnet gasket epdm, bush leaded tin bronze / ptet, gasketepdm / nbr, nut bolt as per is:1363 and is: 1367 ( galvenised steel ) , insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eicincluding jointing & jointing material, labour, testing and commissioning along with pipeline as per technical specification & as per direction of engineer in charge.note: rates are exclusive of tail piece / dismantling joints and earth work.of approved make ( is: 5312 amended upto date ) of following class and dia complete including all material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge.note: rates are exclusive of tail piece / dismantling joints and earth work. 23 100 mmdia 24 pump machinery 25 supply & installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per is:8034 2011 ( pump ) and is 9283 2013 ( motor ) or amended upto date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories , jointing of electrical cables upto switch board, testing of submersible pump set and interconnection upto water mains, complete in all respect. 26 7.5 kw ( 10 hp ) & head above 120 mtr.04 nos 27 up to 5.5 kw ( 7.5 hp ) & head above 120 mtr.02 nos 28 providing & lowering in tubewell isi marked gi pipe “b ( medium ) class as per is:1239 part i 2004 or amended up to date, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect.. 50 mm dia 29 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 4.0 sq.mm 30 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.10.0 sq.mm, 4 core 31 supplying and installing 100 mm diameter sealed diaphragm bourdon type pressure guage of range 0 to 10 kg including all jointing material as per specification with safety cover 32 supplying and fixing of electric control feeder panel comprising of suitable rating mccb, fully automatic star delta starter, over load relay, ampere meter with cts , volt meter, phase preventor, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) all these equipments shall be housed by panel box made from 18 guage ms sheet with powder coating.panel should be of minimum size 900x600x450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having four legs, each legs length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete platform.the size of cc platform should be equal or bigger than the base size of panel having height of atleast 200 mm ground level.the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 33 above 10 hp and up to 15 hp 34 ohsr 35 construction of rcc intze type over head service reserviour of following capacity and stagging consisting of excavation in all types of soils, rcc work, cement plater with water proofing compund to inner face of the container including refilling, disposing off the surplus stuff, plinth protection, all labour and material charges including providing and fixing of accessories such as ladder, manhole frame and covers, water level indicator ( float type ) , ventilator with ss screen, lightening arrestor, float valve, puddle coller, g.i. pipe railing around walk away and tope dome. providing rcc staircase from 4.5 mtr height of ground level to top level, chamber for all valves, providing and applying three coats of cement paint to the external surface of the container, food grade epoxy paint to internal surface of container and giving satisfactory hydraulic test and water tightness test as per is code, etc.complete all in respect as per design data criteria obligatory requirements and detailed specifications, scope of work and ga drwaings.the job includes painting the name of the scheme and other details on the reserviour, providing alluminium portable ladder suitable to reach at 4.5 mtr and other work related to structure as per the direction of engineer in incharge. technical specification and scope of the work. 36 rcc ohsr, 18 meter stagging, sbc 10 t / sqm 37 providing and fixing double flanged isi marked di class k 9 pipes as per is 8329 2000 ( amendment up to date ) as vertical pipes for rcc reservoir including specials required such as a duck foot band, bend tee etc. providing clamp at every 3 mtr, jointing materials suchas nuts bolt rubber packing hydraulic testing etc. complete in all respect up to and from valve chamber as per direction of eic, technical specification specification and scope of work. 38 100 mm 39 providing, lowering, laying, aligning, fixing inpositioninpipeline, resilientseatedd / f disluicevalvesofapprovedmake&design standardoffollowingdiacomplete ( includingjointing&jointing material ) includingallmaterial, labour, testingandcommissioning along with pipe line as per technical specification& as per direction of engineer. manually operated class pn 1.0. ( categoryb ) 40 100 mm dia 41 reparing of exixting glrs in village 42 plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish: 25 mm thick. 43 finishing walls with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding. new work ( three or more coats. ) 44 repair to damaged r.c.c. slab, beams and roof, columns etc. for strenghtening with cement mortor 1:2 in following steps. 1. chopping loose & cracked concrete to required depth. cleaning the exposed surface of steel & concrete with wire brush & sand blasting, papering, cleaning to concrete surface with water as necessary & getting dried 2. applying epoxy primer on the exposed steel bars. 3. applying epoxy hardner & resin mix on concrete and steel bars with brush.4. speading dry cement mortor 1:2 mix over epoxy treated wetsurface & allow it to dry for one day. 5. plastiring the surface with cement sand mortor 1:3 uptodepth of 30 mm complete cure the plasterd surface for 15 days. 45 chopping loose and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brsh and sand blasting, cleaning with a jet of water / air as necessary and getting it dried with compressed air including all scaffolding. depth upto 25mm 46 providing and lying 12mm thick polymer mortar ( 1:3 ) 1 cement : 3coarse sand ) duly mixed with polymer based cement modifier ( powerete pr 40 ) or equivalent ) @ of 5% of the wt. of cement uised and plasticiser, @ 100grm. per bag of cement after applying a polymer slurry coat ( 2 part cement : 1 part powerete pr 40 or equivalent ) as per the recommendations of the manufacturer. 47 providing, supplying, mixing and applying two coats of already to use two component polymer modified flexible cement based water proofing slurry like sike top seal 107, or equivalent by brush after cleaning surfaces, the surface should be cleaned to remover all dust, foreign material, loose material or any deposit of contaminant, which could affact the bond between the surface and sika top seal coating this can be done by scarfying, grinding, water blasting, wire brush or any other approved method including dismantling loose plaster and repairing with cement send 1:4 mix with sika latex, a synthetic rubber emulsion diluted with water in a ration of 1:4 the rust from exposed reinforcement will be removed andanticorrosive treatment with sikaarmatic will have to be done before coating of sika top 107, thw two componentof sika top seal are to be mixed in the ration of1:4 by weight and mixed prpperly until a slurry consistency is achieved, second coat is to be protected from strong wind and direct sunlight and should be curred with demphession or gunny bag or polythene for at least two days as per instruction of manufacture and pecified in the leaf let curring should be done at least for 10 days. 48 providing fabrication and fixing ventilation of the top of reservoir top. size 1.20 mtrdia x 0.75 mtr height with wire gauge 14 mesh x 24 gauge to metal frame of rolled section by metal biding 20 x 3mm ( top, middle and bottom ) side. with suitable screw and post of square bar 12mm and 4 nos of hole pass in fixing m20 cement concrete. 49 providing and applying two coats color lessanti fungus, anti efforseence, water repellent treatment with silicone water repellent ( df, 105 ) or equivalent on the entire exterior surface of the structure of rcc reservoir to obtain the surface perfectly repellent to water all complete. 50 fabrication, supplying and fixing of alluminium ladder inside tank as per specification. 51 distribution pipe line 52 providing, lowering, laying in trenches, aligning, fixing in position and jointingductileiron ( di ) isi markedk 7grades&spipesas per is:8329 2000 ( amendedup todate ) , withinternalcementmortar lining suitable for potablewater with rubber ring ( epdm ) joints as per is: 5382 1985 including all taxes ( central and local ) , transportation and freight charges, inspection charges, loading / unloading charges, including cost of labour and material, specials ( tee, bend etc. ) satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge. ( excluding earth work ) note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 53 100 mm dia di k 7 pipe 54 150 mm dia di k 7 pipe 55 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 ( amended upto date ) with necessary jointing material like mechanical connectors, i.e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading / unloading charges, stacking of pipes, including cost of labour and material, specials ( tee, bend etc. ) , satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. ( excluding earth work ) .note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately.supply may be in coil or straight length in 6 m / 12 m. 56 90 mm dia hdpe pipe pe 80 pn6 57 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 58 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and stacking serviceable material for measurements and disposal of unserviceable material as directed, with in a lead of 50 mtr. including all safety provisions required .: 59 ordinary rock 60 hard rock ( requiring blasting ) 61 hard rock ( blasting prohibited ) 62 dismantling of flexible pavement for pipe lineand chambers by mechanical means using pneumatic tools, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shall be madefor trench width more than specified, re handling of material / earth to complete the tasks per technical specification and scope of work. 63 bituminous courses 64 granular courses 65 construction of bt road 66 providing laying, spreading and compacting stone aggregates of specific sizes as per table 400 7 to water bound macadam specification including spreading in uniform thickness; hand packing, rolling with power roller 8 10 tonnes, in stages to proper grade and camber, applying and brooming requisite type of screening ( table 400 8 ) binding materials to fill up the interstices of coarse aggregates, watering ( with water browser ) and compacting to required density, making necessary earthen bund to protect edges as per clause 404 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion complete. 67 crusher broken grade ii ( 63 45mm ) 68 dismantling of cement concrete pavement for pipe line line and chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, re handling of material / earth to complete the tasks as per technical specification and scope of work. 69 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified, complete work as per technical specification and scope of work. 70 m20 grade nominal mix1: 1.5: 3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) . 71 providing, lowering, aligning, fixing in position in pipe line at work site, di d / f resilient seated ( soft seated ) sluice valves ( gate valves ) , vacuum tight ( bubble tight ) , straight and pocket less body passage of approved make of following class & dia complete confirming to bs en 1171 / awwa c 509 and of following specifications: body & bonnet of ductile cast iron of grade ggg40 / ggg50 as per din 1693 or gr sg 400 / 12 as per is 1865 or equivalent grade as per is :3896 part2 1985 and subsequent revisions, wedge of same material as body & shall vulcanisedrubber lined with epdm ( food grade quality ) and seals of nbr face to face dimensions as per bs 5163 89 / is 14846 / 2000 ( amended up to date ) / din 3202 f4, stem / spindle of ss ( aisi 316 or equivalent ) electrostatic epoxy powder ( ep p ) / fusion bond epoxy ( non toxic suitable for drinking water ) coated with minimum thickness of 250 microns inside and outside, drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367 ( galvanised steel ) insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic, sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece / dismantling joints and earth work. 72 manually operated resilient seated sluice valves of class pn 1.0 / 1.6 73 100 mm dia 74 fhtc 619 nos 75 providing household tap connectionas per technical specification andapproved drawing and as per relevant is code ( amended up to date ) from hdpe pipe line up to consumer meter / premises by using electro fusion saddle piece ( complete job ) .this job includes digging out suitable size of pits and trench for laying service line in all kinds of soil; depositing and refilling of pit & jhiri with watering & ramming / compacting in layers and disposal of surplus excavated soil as directed with in a lead of 100 meter ; providing & fixing of all fitting duly approved in accordance withspecification for potable water including electrofusion saddle piece, gunmetal ferrule 4.0 mm , gm full way valve ( is:778 mark ) or wheel valve and specials, below ground level 20 mm nominal dia mdpe pipe pe80 pn 16 as per iso 4427 / 20 mm nominaldia ppr c ( three layered ) pipepn16 sdr 7.4 ( is:15801:2008 ) ( isi mark ) for and above ground level using 20 mm dia ppr c pipe with standard ppr fittings / 15 mm dia gi pipes with fittings in the premises for fixing a tap / meter box ( excluding ) , including accessories with flushing, cleaning, disinfecting and testing of pipe line complete required for making of service connection complete in all respect including labour charges . the service line should be laid at least 45 cm below ground level.note: road cut and restoration is not part of this item and paid separately. 76 for connection with 20 mm dia mdpe / ppr c pipe length up to 05 mtr. 77 p & f bib cock ( is : 8931 mark ) , superior quality of approved make , brass 400 gm, 15 mm nominal bore. 78 add extra over item no 1.21, 1.22 & 1.23 for providing20 mm pe80 pn 16 as per iso 4427 mdpe pipe including excavation, providing, laying & jointing of service line above 5.00 mtr....

Public Health Engineering Department - Rajasthan

36392273 tender for commissioning of tube well at mule ka tala g.p. gangasara 1 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 2 providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes 65mm dia 3 supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. 4 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. above 10 hp and up to 15 hp 5 supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 9.3 kw ( 12.5 hp ) & head above 120 mtr. 6 supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 16.0 sq.mm 7 providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65mm dia 8 supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. . 3 core 6.0 sq.mm 9 sitc star delta starter type lt panel of following rating: all switchgears are of phed approved makes, crca sheet of panel enclosure is of tata / essar 1.6mm / 2.0mm thick duly electrostatic powder coated with angle frame including other ancillaries ( insulators, acrylic sheet , baklight sheet, hardware, wire, name plates, lugs, pvc channel , mcb chanel , lock, hing , bidding , connectors, netural links , sprial , saddle & packing material ) etc. and 100a / 125a , tpn, aluminum bus bar with colour coated heat shrinkage sleeves complete as per technical specifications and as per direction of engineer in charge. star delta starter 11.0 kw ( 15.0 hp ) : for 2 motors ( 1 w+ 1s ) i / c mcb 63a , fp, 10 ka, c curve ( 1 ) , analog voltmeter 96*96mm ( 0 500v ) ( 1 ) , volt selector switch ( 1 ) , analog ammeter 96*96mm ( 0 60a ) ( 1 ) , amp. selector switch ( 1 ) , c. t. 60 / 5a cl 1.0 5va ( 3 ) , indicating lights ( red 1, yellow 1 ) ( 2 ) , indicating lights ( blue 1 ) ( 1 ) , control mcb 6a sp 10 ka c curve ( 3 ) and o / g mcb 40a , tp, 10 ka, c curve ( 2 ) , power cont 25a tp ac3 duty ( 2 ) , 2 no+2 nc aux. block ( 2 ) , thermal overload relay ( 9 13a ) ( 2 ) , control mcb 6a sp 10 ka c curve ( 2 ) , single phase priventer ( 2 ) , indicating lights ( red 1, green 1, amber 1 ) ( 6 ) , push button 22.5 ( red 1, green 1 ) ( 4 ) , selector switch 1 pole, 2 way ( 2 ) , capacitor 440vac heavy duty mpp type 7.5kvar ( 2 ) , s / d timer ( 2 ) ...

Public Health Engineering Department - Rajasthan

36391972 tender for commissioning of tube well at ikri nadi village gangasara g.p. gangasara supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 2 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay,ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom).all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. above 10 hp and up to 15 hp 3 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 6.0 sq.mm 4 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 16.0 sq.mm 5 providing & lowering in tube well isi marked gi pipe medium duty (“b class), steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65mm dia 6 providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes 65mm dia 7 supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg.including all jointing material as per specification with safety cover. 8 supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect.9.3kw (12.5 hp) & head above 120 mtr. ...

Public Health Engineering Department - Rajasthan

36391932 tender for rate contract for commissioning of tube wells under city dn.barmer testing verticality of tube well by plumbing system and yield test and draw down test by pumping system as per is : 2800 ( part – ii ) – 1979 or as per amended up to date. 3 supplying & packingp gravel suitable for slot size / mesh size as suggested in is 2800 ( part 1 ) 1991 or as per amended up to date. 4 development of tube well having depth up to 250 mtr as per is: 11189 1985 and is: 2800 ( part i ) 1991 ( both amended up to date ) using suitable methods to give sand free water for required yield of the gravel packed tube well. 5 supply of erw m.s. black casing pipe isi marked ( is: 4270 / 2001 ) or amended up to dateoffollowing sizes200 mm dia nb ( thickness of pipe 5.0 mm & mass of tube 20.13 kg / m ) 6 250 mm dia nb ( thickness of pipe 7.1 mm & mass of tube 46.57 kg / m ) 7 labour charges for making slots on blank pipes made of erw ms black pipe isi marked of following sizes, the slotting should be as per is:8110 1985.200 mm dia nominal bore of 4.8 mm thickness 8 250 mm dia nominal bore of 7.1mm thickness 9 supply of isi mark ac pressure pipe class 15 manufactured by mazza process as per is:1592 2003 or amended upto date, for casing of tube wellfor following dia nominal bore, with jointing material pvc coupler as per technical specification and direction of engineer in charge. 200 mm nominal dia 10 250 mm nominal dia 11 300 mm nominal dia 12 making slots of hole size and nos. as directed by eic in ac pressure pipe class 15 as per technical specification for using slotted pipe in tw casing. 13 providing and lowering of isi mark pvc u casing and screen pipe as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for tw and dcb with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. shallow well casing pipe ( cs ) suitable for depth up to 80 mtr. 200 mm nominal dia ( internal dia ) . 14 250 mm nominal dia ( internal dia ) . 15 medium well casing pipe ( cm ) suitable for depth above 80 mtr and up to 250 mtr. 100 mm nominal dia ( internal dia ) . 16 200 mm nominal dia ( internal dia ) . 17 250 mm nominal dia ( internal dia ) . 18 providing & laying isi marked gi pipe light duty ( “a” class ) as peris: 1239for casing pipe for submersible cable external work 40 mm dia complete in all respect. 19 supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. up to 5.5 kw ( 7.5 hp ) & head up to 120 mtr. 20 up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. 21 7.5 kw ( 10 hp ) & head up to 120 mtr. 22 7.5 kw ( 10 hp ) & head above 120 mtr. 23 9.3 kw ( 12.5 hp ) & head up to 120 mtr. 24 9.3kw ( 12.5 hp ) & head above 120 mtr. 25 11 kw ( 15 hp ) & head up to 120 mtr. 26 11 kw ( 15 hp ) & head above 120 mtr. 27 13 kw ( 17.5 hp ) & head up to 120 mtr. 28 13 kw ( 17.5 hp ) & head above 120 mtr. 29 15 kw ( 20 hp ) and above, head up to 120 mtr. 30 15 kw ( 20 hp ) and above, head above 120 mtr. 31 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. above 5 hp and up to 10 hp 32 above 10 hp and up to 15 hp 33 above 15 hp and upto 20 hp 34 above 20 hp and upto 30 hp 35 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc.3 core 4.0 sq.mm 36 3 core 6.0 sq.mm 37 3 core 10.0 sq.mm 38 3 core 16.0 sq.mm 39 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 10.0 sq.mm, 4 core 40 16.0 sq.mm, 4 core 41 25.0 sq.mm, 3.5 core 42 35.0 sq.mm, 3.5 core 43 plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. 44 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 45 supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 125 mm dia 46 150 mm dia 47 200 mm dia 48 250 mm dia 49 providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 32 mm dia 50 50 mm dia 51 65 mm dia 52 80mm dia 53 providing & lowering in tube well isi marked hdpe pipe as per is 4984:1995 or amended upto date in pe 80 grade and class pn 10 of following dia. including hdpe / gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. 40 mm dia 54 50 mm dia 55 63 mm dia 56 75 mm dia 57 90 mm dia 58 providing & fixing pump safety cage as per specifications or as directed by engineer in charge. 59 providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes 65 mm dia 60 80 mm dia 61 proving and fixing 32 mm dia full way valve or wheel valve as per is:778 or amended up to date of approved make, on pump delivery pipe. 62 supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg.including all jointing material as per specification with safety cover....

North Western Railway - Rajasthan

36365959 supply of flange welded joint ( for 20 mm pipe ) flange welded joint ( for 20 mm pipe ) , flange welded joint ( for 20 mm pipe ) sk 85187 alt 1 item no. 1 to 7 [ warranty period: 30 months after the date of delivery ] ...

Public Health Engineering Department - Rajasthan

36305990 tender for rejuvenation of existing tube well during canal closure under pdr division ii bikaner supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 3 11 kw ( 15 hp ) & head above 120 mtr. 4 13 kw ( 17.5 hp ) & head up to 120 mtr. 5 13 kw ( 17.5 hp ) & head above 120 mtr. 6 15 kw ( 20 hp ) and above, head up to 120 mtr. 7 15 kw ( 20 hp ) and above, head above 120 mtr. 8 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. above 15 hp and up to 20 hp 9 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 10.0 sq.mm 10 providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 11 supply and fixing of oil / air breakdol / star deltastartermade out of sheet steelpowder coated enclosure withsingle phasing protection, on / offpush buttons, etc. complete in all respect suitable for following rating motors. 30.0 hp to 35.0 hp...

Public Health Engineering Department - Rajasthan

36102618 emergent work ( summer contingency ) during summer season 2023 under jen section bajju phed sub dn. bajju earth work in excavation by mechanical means (hydraulic excavator )/ manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 3 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 (amended up to date)with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (tee, bend etc.), satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. (excluding earth work) .note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately.supply may be in coil or straight length in 6 m/12 m. hdpe pe 80pn 6 4 75 mm dia 5 90 mm dia 6 providing, lowering, laying and jointing in trenches, standard lengths isi marked ac pressure pipe class 15 manufactured by mazza process as per is 1592 2003 or amended up to date with ac coupling andepdmrubber sealing rings of type 3 as per is: 5382/1985 (reaffirmed 1998) or amended up to date, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, labour and material,satisfactory hydraulic testing etc. complete as per technical specifications and direction of engineer in charge. (excluding earth work and specials) note: these pipes shall only be used for raw water conveyance mainfrom canal outlet to raw water reservoirs and interconnection works. 7 150 mm dia cl 15 8 200 mm dia cl 15 9 providing and fixing of flanged/ plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding,lowering,laying,aligning,fixinginpositionatalllevel/ depths in trenches complete includingall taxes, material,labour, inside lining, outside coating, testingandcommissioning alongwithpipelineaspertechnicalspecifications anddirection of engineer in charge. ms pipespecialsup to600mmdia (withminimum5mmthickness sheet) 10 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesstraight and pocket less body passage of approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem aisi 410 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date) ,epoxy ( non toxic suitable for drinking water) applied inside and outside,flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steelinsertion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. manually operated ci sluice valve of class pn 1.0 11 80 mm hw 12 100 mm hw 13 125 mm hw 14 150 mm hw 15 200 mm hw 16 providing, installation, testing and commissioning of centrifugal monoblock pump set conforming to is 9079 , 2 pole motor operating at synchronised speed of 3000 rpm with requisite moc impeller, priming funnel, cock, suitable flanges at suction and delivery side. pump shall have common shaft for pump and motor. motor shall be suitable for working on 415 v ± 10%, 3 ph, 50 hz a.c. supply. motor shall be tefc type and pump set shall be suitable for working at various discharge and head requirements as per scope of work. pump shall be erected onc.c. foundation / cross channels / rsj frame block with suitable foundation bolts grouted in c.c. foundation block etc. complete in all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions mentioned in td. 17 5.5 kw (7.5 hp) 18 7.5 kw (10 hp) 19 9.3 kw (12.5 hp) 20 11.0 kw (15 hp) 21 15.0 kw (20.0 hp) 22 dol starter 5.5 kw (7.5hp) : for 2 motors (1 w+ 1s)i/c mcb 40a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 30/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) and o/g mcb 25a ,tp, 10 ka, c curve (2), power cont 12a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 2 kvar (2) 23 star delta starter 7.5 kw (10.0 hp) : for 2 motors(1 w+ 1s) i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) ando/g mcb 32a ,tp, 10 ka, c curve (2), power cont 18a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 5kvar (2), s/d timer(2) 24 star delta starter 9.3 kw (12.5 hp) : for 2 motors (1 w+ 1s)i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) and o/g mcb 40a ,tp, 10 ka, c curve (2), power cont 18a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 5kvar (2), s/d timer(2) 25 star delta starter 11.0 kw (15.0 hp) :for 2 motors (1 w+ 1s) i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) and o/g mcb 40a ,tp, 10 ka, c curve (2), power cont 25a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (9 13a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 7.5kvar (2), s/d timer(2) 26 star delta starter15.0 kw (20.0 hp) :for 2 motors (1 w+ 1s) i/c mccb 100a tpn 25 ka with t/m based over current & short circuit protection (1),spreaders (2),extended rotary handle (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 100/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3)and o/g mccb 63a tpn 25 ka with t/m based over current & short circuit protection (2), power cont 32a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (12 18a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 7.5kvar (2), s/d timer(2) 27 providing, installation, testing and commissioning of submersible monoblock pump set conforming to is 8034 and2 pole motor operating at synchronised speed of speed 3000 rpm, with water proof winding. pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415 v ± 10%, 3 ph, 50 hz ac and with water lubricated bearing to accept entire hydraulic thrust. supply, with cable guard, thrust carbon/fibre bearing to withstand entire hydraulic thrust. the pump set shall be suitable for direct coupling, with suitable suction strainer. pump should have suitable discharge out let as per manufacturers design. antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. completein all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions mentioned in td. 28 5.5 kw (7.5 hp) 29 7.5 kw (10 hp) 30 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 31 3 core 6.0 sq.mm 32 3 core 10.0 sq.mm 33 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 35.0 sq.mm, 3.5 core 34 providing & lowering in tube well isi marked gi pipe medium duty (“b class), steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 35 65 mm dia 36 80mm dia ...

Public Health Engineering Department - Rajasthan

36102603 emergent work (summer contingency) during summer season 2023 under jen section gadiyala phed sub dn. bajju earth work in excavation by mechanical means (hydraulic excavator )/ manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 3 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 (amended up to date)with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (tee, bend etc.), satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. (excluding earth work) .note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately.supply may be in coil or straight length in 6 m/12 m. hdpe pe 80pn 6 4 75 mm dia 5 90 mm dia 6 providing, lowering, laying and jointing in trenches, standard lengths isi marked ac pressure pipe class 15 manufactured by mazza process as per is 1592 2003 or amended up to date with ac coupling andepdmrubber sealing rings of type 3 as per is: 5382/1985 (reaffirmed 1998) or amended up to date, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, labour and material,satisfactory hydraulic testing etc. complete as per technical specifications and direction of engineer in charge. (excluding earth work and specials) note: these pipes shall only be used for raw water conveyance mainfrom canal outlet to raw water reservoirs and interconnection works. 7 150 mm dia cl 15 8 200 mm dia cl 15 9 providing and fixing of flanged/ plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding,lowering,laying,aligning,fixinginpositionatalllevel/ depths in trenches complete includingall taxes, material,labour, inside lining, outside coating, testingandcommissioning alongwithpipelineaspertechnicalspecifications anddirection of engineer in charge. ms pipespecialsup to600mmdia (withminimum5mmthickness sheet) 10 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesstraight and pocket less body passage of approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem aisi 410 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date) ,epoxy ( non toxic suitable for drinking water) applied inside and outside,flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steelinsertion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. manually operated ci sluice valve of class pn 1.0 11 80 mm hw 12 100 mm hw 13 125 mm hw 14 150 mm hw 15 providing, installation, testing and commissioning of centrifugal monoblock pump set conforming to is 9079 , 2 pole motor operating at synchronised speed of 3000 rpm with requisite moc impeller, priming funnel, cock, suitable flanges at suction and delivery side. pump shall have common shaft for pump and motor. motor shall be suitable for working on 415 v ± 10%, 3 ph, 50 hz a.c. supply. motor shall be tefc type and pump set shall be suitable for working at various discharge and head requirements as per scope of work. pump shall be erected onc.c. foundation / cross channels / rsj frame block with suitable foundation bolts grouted in c.c. foundation block etc. complete in all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions mentioned in td. 16 5.5 kw (7.5 hp) 17 7.5 kw (10 hp) 18 9.3 kw (12.5 hp) 19 11.0 kw (15 hp) 20 15.0 kw (20.0 hp) 21 dol starter 5.5 kw (7.5hp) : for 2 motors (1 w+ 1s)i/c mcb 40a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 30/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) and o/g mcb 25a ,tp, 10 ka, c curve (2), power cont 12a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 2 kvar (2) 22 star delta starter 7.5 kw (10.0 hp) : for 2 motors(1 w+ 1s) i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) ando/g mcb 32a ,tp, 10 ka, c curve (2), power cont 18a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 5kvar (2), s/d timer(2) 23 star delta starter 9.3 kw (12.5 hp) : for 2 motors (1 w+ 1s)i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) and o/g mcb 40a ,tp, 10 ka, c curve (2), power cont 18a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 5kvar (2), s/d timer(2) 24 star delta starter 11.0 kw (15.0 hp) :for 2 motors (1 w+ 1s) i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3) and o/g mcb 40a ,tp, 10 ka, c curve (2), power cont 25a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (9 13a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 7.5kvar (2), s/d timer(2) 25 star delta starter15.0 kw (20.0 hp) :for 2 motors (1 w+ 1s) i/c mccb 100a tpn 25 ka with t/m based over current & short circuit protection (1),spreaders (2),extended rotary handle (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 100/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3)and o/g mccb 63a tpn 25 ka with t/m based over current & short circuit protection (2), power cont 32a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (12 18a )(2), control mcb 6a sp 10 ka c curve (2), single phase preventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 7.5kvar (2), s/d timer(2) 26 providing, installation, testing and commissioning of submersible monoblock pump set conforming to is 8034 and2 pole motor operating at synchronised speed of speed 3000 rpm, with water proof winding. pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415 v ± 10%, 3 ph, 50 hz ac and with water lubricated bearing to accept entire hydraulic thrust. supply, with cable guard, thrust carbon/fibre bearing to withstand entire hydraulic thrust. the pump set shall be suitable for direct coupling, with suitable suction strainer. pump should have suitable discharge out let as per manufacturers design. antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. completein all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions mentioned in td. 27 5.5 kw (7.5 hp) 28 7.5 kw (10 hp) 29 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 30 3 core 6.0 sq.mm 31 3 core 10.0 sq.mm 32 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 35.0 sq.mm, 3.5 core 33 providing & lowering in tube well isi marked gi pipe medium duty (“b class), steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 34 65 mm dia 35 80mm dia ...

Public Health Engineering Department - Rajasthan

36102597 emergent work ( summer contingency ) during summer season 2023 under jen section jhajhu phed sub dn. kolayat supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 3 11 kw (15 hp) & head above 120 mtr. 4 13 kw (17.5 hp) & head above 120 mtr. 5 15 kw (20 hp) and above, head above 120 mtr. 6 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 6.0 sq.mm 7 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 10.0 sq.mm 8 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 16.0 sq.mm, 4 core 9 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesstraight and pocket less body passage of approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem aisi 410 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date) ,epoxy ( non toxic suitable for drinking water) applied inside and outside,flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steelinsertion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. manually operated ci sluice valve of class pn 1.0 10 80 mm hw 11 100 mm hw 12 providing, lowering, aligning, fixing in position in pipe line, ci double flanged swing type non return valves (nrv)of approved make of following pressure rating & dia complete, confirming to is: 5312 (part 1)/ 2004 (amendedup to date) and of following specifications: body, cover & disc of grey cast iron of is:210/ fg200. face to face dimensions as per is 5312 (part 1):2004 , flanges drilled as per is:1538. epoxy(non toxic & suitable for drinking water) applied on body, cover and disc inside and outside . body seat ring of ss/cs door face ring epdm/ neoprene (food grade quality) ,shaft ofss aisi 410 ,hinge malleable cast iron / ss aisi 316 ,bonnet gasket epdm, bush leaded tin bronze/ ptet, gasketepdm/nbr,nut bolt as per is:1363 and is: 1367 (galvanised steel) ,insertion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic including jointing & jointing material, labour, testing and commissioning along with pipeline as per technical specification & as per direction of engineer in cha rge.note: rates are exclusive of tail piece/ dismantling joints and earth work. class pn 1.0 80 mm dia 13 providing & lowering in tube well isi marked gi pipe medium duty (“b class), steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 14 65 mm dia 15 80mm dia 16 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay,ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom).all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 17 above 15 hp ...

Public Health Engineering Department - Rajasthan

36102594 emergent work ( summer contingency ) during summer season 2023 under jen section kolayat phed sub dn. kolayat supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 3 11 kw (15 hp) & head above 120 mtr. 4 13 kw (17.5 hp) & head above 120 mtr. 5 15 kw (20 hp) and above, head above 120 mtr. 6 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 6.0 sq.mm 7 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 10.0 sq.mm 8 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 16.0 sq.mm, 4 core 9 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesstraight and pocket less body passage of approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem aisi 410 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date) ,epoxy ( non toxic suitable for drinking water) applied inside and outside,flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steelinsertion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. manually operated ci sluice valve of class pn 1.0 10 80 mm hw 11 100 mm hw 12 providing, lowering, aligning, fixing in position in pipe line, ci double flanged swing type non return valves (nrv)of approved make of following pressure rating & dia complete, confirming to is: 5312 (part 1)/ 2004 (amendedup to date) and of following specifications: body, cover & disc of grey cast iron of is:210/ fg200. face to face dimensions as per is 5312 (part 1):2004 , flanges drilled as per is:1538. epoxy(non toxic & suitable for drinking water) applied on body, cover and disc inside and outside . body seat ring of ss/cs door face ring epdm/ neoprene (food grade quality) ,shaft ofss aisi 410 ,hinge malleable cast iron / ss aisi 316 ,bonnet gasket epdm, bush leaded tin bronze/ ptet, gasketepdm/nbr,nut bolt as per is:1363 and is: 1367 (galvanised steel) ,insertion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic including jointing & jointing material, labour, testing and commissioning along with pipeline as per technical specification & as per direction of engineer in cha rge.note: rates are exclusive of tail piece/ dismantling joints and earth work. class pn 1.0 80 mm dia 13 providing & lowering in tube well isi marked gi pipe medium duty (“b class), steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 14 65 mm dia 15 80mm dia 16 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay,ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom).all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 17 above 15 hp ...

Public Health And Engineering Department - Rajasthan

36030103 rejuvenation of jjy schemes including replacement of submersible pump sets / panels / cables and other allied works required for functioning of tube well in all respect including one year defect liability period under jen section kolu pabuji rejuvenation of jjy schemes including replacement of submersible pump sets / panels / cables and other allied works required for functioning of tube well in all respect including one year defect liability period under jen section kolu pabuji , phed bsr / 2022 23 / chapter 2 / 2.14 / supply& installationof single phase isl marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includesloweringof motor pump, installationof complete fitting & accessories, jointing of electrical cables up to switch board, testingofsubmersiblepumpsetandinterconnectionuptowatermains, complete in all respect. , 2.14.1 ) up to 2.0 kw , 2.14.2 ) above 2.0 kw , phed bsr / 2022 23 / chapter 2 / 2.15 / supply & installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , 2.15.1 ) up to 5.5 kw ( 7.5 hp ) & head up to 120 mtr. , 2.15.2 ) up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. , 2.15.3 ) 7.5 kw ( 10 hp ) & head up to 120 mtr. , 2.15.4 ) 7.5 kw ( 10 hp ) & head above 120 mtr , 2.15.5 ) 9.3 kw ( 12.5 hp ) & head up to 120 mtr. , 2.15.6 ) 9.3 kw ( 12.5 hp ) & head above 120 mtr. , 2.15.7 ) 11 kw ( 15 hp ) & head up to 120 mtr. , 2.15.8 ) 11 kw ( 15 hp ) & head above 120 mtr. , 2.15.9 ) 3 kw ( 17.5 hp ) & head up to 120 mtr. , 2.15.10 ) 13 kw ( 17.5 hp ) & head above 120 mtr. , 2.15.11 ) 15 kw ( 20 hp ) and above, head up to 120 mtr. , 2.15.12 ) 15 kw ( 20 hp ) and above, head above 120 mtr. , phed bsr / 2022 23 / chapter 2 / 2.16 / supply and fixing of electric feeder panel ( having projected canopy ) for submersible pump set single phase upto 5 hp, comprising of dol starter, mcb, indicating light, ammeter, volt meter, connection plate, condensers of approved make and the panel enclosure should be made out from 18 gauge m.s. sheet with powder coating. panel size height 600 mm width 500 mm depth 250 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the operation of panel should be suitable for on 240 volt ac supply. , phed bsr / 2022 23 / chapter 2 / 2.17 / supply and fixing of electric control feeder panel comprising of suitable rating mccb, dol starter, overload relay, ampere meter, volt meter, phase preventer, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 300mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 2.17.1 ) up to 5.00 hp , phed bsr / 2022 23 / chapter 2 / 2.18 / supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lightingarrangementetc. completesuitablefor threephasepumpset. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. , 2.18.1 ) above5 hpand upto 10 hp , 2.18.2 ) above 10 hp and up to 15 hp , 2.18.3 ) above 15 hp and up to 20 hp , 2.18.4 ) above 20 hp and up to 30 hp , phed bsr / 2022 23 / chapter 2 / 2.19 / supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. , 2.19.1 ) 3 core 4.0 sq.mm , 2.19.2 ) 3 core 6.0 sq.mm , 2.19.3 ) 3 core 10.0 sq.mm , 2.19.4 ) 3 core 16.0 sq.mm , phed bsr / 2022 23 / chapter 2 / 2.20 / supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. , 2.20.1 ) 10.0 sq.mm, 4 core , 2.20.2 ) 16.0 sq.mm, 4 core , 2.20.3 ) 25.0 sq.mm, 3.5 core , 2.20.4 ) 35.0 sq.mm, 3.5 core , phed bsr / 2022 23 / chapter 2 / 2.21 / plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , phed bsr / 2022 23 / chapter 2 / 2.22 / supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , phed bsr / 2022 23 / chapter 2 / 2.23 / supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. , 2.23.1 ) 125 mm dia , 2.23.2 ) 150 mm dia , 2.23.3 ) 200 mm dia , 2.23.4 ) 250 mm dia , phed bsr / 2022 23 / chapter 2 / 2.24 / providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. , 2.24.1 ) 32 mm dia , 2.24.2 ) 50 mm dia , 2.24.3 ) 65 mm dia , 2.24.4 ) 80 mm dia , phed bsr / 2022 23 / chapter 2 / 2.25 / providing & lowering in tube well isi marked hdpe pipe as per is 4984:1995 or amended upto date in pe 80 grade and class pn 10 of following dia. including hdpe / gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. , 2.25.1 ) 40 mm dia , 2.25.2 ) 50 mm dia , 2.25.3 ) 63 mm dia , 2.25.4 ) 75 mm dia , 2.25.5 ) 90 mm dia , phed bsr / 2022 23 / chapter 2 / 2.26 / providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. , 2.26.1 ) 50 mm dia , 2.26.2 ) 65 mm dia , 2.26.3 ) 80 mm dia , phed bsr / 2022 23 / chapter 2 / 2.27 / providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , phed bsr / 2022 23 / chapter 2 / 2.28 / providing and fixing of isi marked pvc storage tank of following capacity as per is: 12701 1989 ( of approved make ) with cover, 25 mm dia. 1 mtr long gi overflow pipe, 25 cm long 25 mm dia washout gi pipe with plug & socket, including p&f 32 mm dia ball cock ( float valve ) is 1703 marked with rod and pvc ball complete with brass weight 1000 gm, including p&f 15 mm dia ci quarter turn heavy duty bib cocks four nos. of superior quality and approved make, including interconnections complete job. , 2.28.1 ) 1000 litres capacity , 2.28.2 ) 2000 litres capacity , phed bsr / 2022 23 / chapter 2 / 2.29 / fabrication & fixing m.s. stand of specified class of angle iron lshaped of 50 mm size with four legs grouted by 300*300*300 mm cc block m 15 in the ground and all legs tied up with each other through same size of angle iron along with cross bars to support the bottom of 1000 ltr. / 2000 ltr. pvc tank complete in all respect. , phed bsr / 2022 23 / chapter 2 / 2.30 / providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes , 2.30.1 ) 65 mm dia , 2.30.2 ) 80 mm dia , phed bsr / 2022 23 / chapter 2 / 2.31 / proving and fixing 32 mm dia full way valve or wheel valve as per is:778 or amended up to date of approved make, on pump delivery pipe. , phed bsr / 2022 23 / chapter 2 / 2.32 / supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , phed bsr / 2022 23 / 2.34 providing and lowering of isi mark pvc u casing and screen pipe as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for tw and dcb with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. , 2.34.1 ) shallow well casing pipe ( cs ) suitable for depth up to 80 mtr. , 2.34.1.1 ) 150 mm nominal dia ( internal dia ) . , 2.34.1.2 ) 200 mm nominal dia ( internal dia ) . , 2.34.1.3 ) 250 mm nominal dia ( internal dia ) . , 2.34.2 ) medium well casing pipe ( cm ) suitable for depth above 80 mtr and up to 250 mtr. , 2.34.2.1 ) 100 mm nominal dia ( internal dia ) . , 2.34.2.2 ) 125 mm nominal dia ( internal dia ) . , 2.34.2.3 ) 150 mm nominal dia ( internal dia ) . , 2.34.2.4 ) 200 mm nominal dia ( internal dia ) . , 2.34.2.5 ) 250 mm nominal dia ( internal dia ) . , phed bsr / 2022 23 / 1.4 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 ( amended up to date ) with necessary jointing material like mechanical connectors, i.e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading / unloading charges, stacking of pipes, including cost of labour and material, specials ( tee, bend etc. ) , satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. ( excluding earth work ) . note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. supply may be in coil or straight length in 6 m / 12 m. , hdpe pe 80pn 6 , 75 mm dia , 90 mm dia , phed bsr / 2022 23 / chapter 6 / 6.1 / providing, lowering, aligning, fixing in position in pipe line, ci d / f sluice valves straight and pocket less body passage of approved make of following pressure rating & dia complete, confirfing to is:14846 ( amended up to date ) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210 / fg200 stem ss 304 , body seat ring, wedge facing ring & bushes ltb2 / ss , face to face dimensions as per is 14846 / 2000 ( amended up to date ) , epoxy ( non toxic suitable for drinking water ) applied inside and outside, flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367 / cs / galvanised steel insersion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece / dismantling joints and earth work. , 6.1.1 manually operated ci sluice valve of class pn 1.0 , 6.1.1.1 80 mm hw , 6.1.1.2 100 mm hw...

Public Health And Engineering Department - Rajasthan

36030093 rejuvenation of jjy schemes including replacement of submersible pump sets / panels / cables and other allied works required for functioning of tube well in all respect including one year defect liability period under jen section shaitansingh nagar rejuvenation of jjy schemes including replacement of submersible pump sets / panels / cables and other allied works required for functioning of tube well in all respect including one year defect liability period under jen section shaitan singh nagar , phed bsr/2022 23/ chapter 2/2.14/ supply& installationof single phase isl marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includesloweringof motor pump, installationof complete fitting & accessories, jointing of electrical cables up to switch board, testingofsubmersiblepumpsetandinterconnectionuptowatermains, complete in all respect. , 2.14.1) up to 2.0 kw , 2.14.2)above 2.0 kw , phed bsr/2022 23/ chapter 2/2.15/ supply & installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , 2.15.1) up to 5.5 kw (7.5 hp) & head up to 120 mtr. , 2.15.2) up to 5.5 kw (7.5 hp) & head above 120 mtr. , 2.15.3) 7.5 kw (10 hp) & head up to 120 mtr. , 2.15.4) 7.5 kw (10 hp) & head above 120 mtr , 2.15.5) 9.3 kw (12.5 hp) & head up to 120 mtr. , 2.15.6) 9.3 kw (12.5 hp) & head above 120 mtr. , 2.15.7) 11 kw (15 hp) & head up to 120 mtr. , 2.15.8) 11 kw (15 hp) & head above 120 mtr. , 2.15.9)3 kw (17.5 hp) & head up to 120 mtr. , 2.15.10) 13 kw (17.5 hp) & head above 120 mtr. , 2.15.11) 15 kw (20 hp) and above, head up to 120 mtr. , 2.15.12) 15 kw (20 hp) and above, head above 120 mtr. , phed bsr/2022 23/ chapter 2/2.16/ supply and fixing of electric feeder panel (having projected canopy)for submersible pump set single phase upto 5 hp, comprising of dol starter, mcb, indicating light, ammeter, volt meter, connection plate, condensers of approved make and the panel enclosure should be made out from 18 gauge m.s. sheet with powder coating. panel size height 600 mm width 500 mm depth 250 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the operation of panel should be suitable for on 240 volt ac supply. , phed bsr/2022 23/ chapter 2/2.17/ supply and fixing of electric control feeder panel comprising of suitable rating mccb, dol starter, overload relay, ampere meter, volt meter, phase preventer, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom). all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 300mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 2.17.1)up to 5.00 hp , phed bsr/2022 23/ chapter 2/2.18/ supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay,ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lightingarrangementetc. completesuitablefor threephasepumpset. the panel should have space for energy meter ( supplied by discom).all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. , 2.18.1) above5 hpand upto 10 hp , 2.18.2) above 10 hp and up to 15 hp , 2.18.3) above 15 hp and up to 20 hp , 2.18.4) above 20 hp and up to 30 hp , phed bsr/2022 23/chapter 2/2.19/ supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. , 2.19.1) 3 core 4.0 sq.mm , 2.19.2) 3 core 6.0 sq.mm , 2.19.3) 3 core 10.0 sq.mm , 2.19.4) 3 core 16.0 sq.mm , phed bsr/2022 23/ chapter 2/2.20/ supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. , 2.20.1) 10.0 sq.mm, 4 core , 2.20.2) 16.0 sq.mm, 4 core , 2.20.3) 25.0 sq.mm, 3.5 core , 2.20.4) 35.0 sq.mm, 3.5 core , phed bsr/2022 23/ chapter 2/2.21/ plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer ,nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. , phed bsr/2022 23/ chapter 2/2.22/ supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , phed bsr/2022 23/chapter 2/2.23/ supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1/2 (for installation pressure gauge) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. , 2.23.1) 125 mm dia , 2.23.2) 150 mm dia , 2.23.3) 200 mm dia , 2.23.4) 250 mm dia , phed bsr/2022 23/ chapter 2/2.24/ providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged (welded) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. , 2.24.1) 32 mm dia , 2.24.2) 50 mm dia , 2.24.3) 65 mm dia , 2.24.4) 80 mm dia , phed bsr/2022 23/chapter 2/2.25/ providing & lowering in tube well isi marked hdpe pipe as per is 4984:1995 or amended upto date in pe 80 grade and class pn 10 of following dia. including hdpe/gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. , 2.25.1) 40 mm dia , 2.25.2) 50 mm dia , 2.25.3) 63 mm dia , 2.25.4) 75 mm dia , 2.25.5) 90 mm dia , phed bsr/2022 23/ chapter 2/2.26/ providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064/1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box (sheet 16 swg) suitable with locking arrangement of following dia. , 2.26.1) 50 mm dia , 2.26.2) 65 mm dia , 2.26.3) 80 mm dia , phed bsr/2022 23/ chapter 2/2.27/ providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , phed bsr/2022 23/chapter 2/2.28/ providing and fixing of isi marked pvc storage tank of following capacity as per is: 12701 1989 (of approved make) with cover, 25 mm dia. 1 mtr long gi overflow pipe, 25 cm long 25 mm dia washout gi pipe with plug & socket, including p&f 32 mm dia ball cock (float valve) is 1703 marked with rod and pvc ball complete with brass weight 1000 gm, including p&f 15 mm dia ci quarter turn heavy duty bib cocks four nos. of superior quality and approved make, including interconnections complete job. , 2.28.1) 1000 litres capacity , 2.28.2) 2000 litres capacity , phed bsr/2022 23/chapter 2/2.29/ fabrication & fixing m.s. stand of specified class of angle iron lshaped of 50 mm size with four legs grouted by 300*300*300 mm cc block m 15 in the ground and all legs tied up with each other through same size of angle iron along with cross bars to support the bottom of 1000 ltr./ 2000 ltr. pvc tank complete in all respect. , phed bsr/2022 23/ chapter 2/2.30/ providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes , 2.30.1) 65 mm dia , 2.30.2) 80 mm dia , phed bsr/2022 23/ chapter 2/2.31/ proving and fixing 32 mm dia full way valve or wheel valve as per is:778 or amended up to date of approved make, on pump delivery pipe. , phed bsr/2022 23/chapter 2/2.32/ supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , phed bsr/2022 23/ 2.34 providing and lowering of isi mark pvc u casing and screen pipe as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for tw and dcb with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. , 2.34.1) shallow well casing pipe (cs) suitable for depth up to 80 mtr. , 2.34.1.1) 150 mm nominal dia ( internal dia ). , 2.34.1.2) 200 mm nominal dia ( internal dia ). , 2.34.1.3) 250 mm nominal dia ( internal dia ). , 2.34.2) medium well casing pipe (cm) suitable for depth above 80 mtr and up to 250 mtr. , 2.34.2.1) 100 mm nominal dia ( internal dia ). , 2.34.2.2) 125 mm nominal dia ( internal dia ). , 2.34.2.3) 150 mm nominal dia ( internal dia ). , 2.34.2.4) 200 mm nominal dia ( internal dia ). , 2.34.2.5) 250 mm nominal dia ( internal dia ). , phed bsr/2022 23/ 1.4 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 (amended up to date)with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (tee, bend etc.), satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. (excluding earth work) . note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. supply may be in coil or straight length in 6 m/12 m. , hdpe pe 80pn 6 , 75 mm dia , 90 mm dia , phed bsr/2022 23/chapter 6/6.1/ providing, lowering, aligning, fixing in position in pipe line, ci d/f sluice valves straight and pocket less body passage of approved make of following pressure rating & dia complete, confirfing to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200 stem ss 304 ,body seat ring, wedge facing ring & bushes ltb2/ ss , face to face dimensions as per is 14846/2000 (amended up to date) ,epoxy ( non toxic suitable for drinking water) applied inside and outside, flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steel insersion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. , 6.1.1 manually operated ci sluice valve of class pn 1.0 , 6.1.1.1 80 mm hw , 6.1.1.2 100 mm hw...

Public Health And Engineering Department - Rajasthan

36026516 rejuvenation of jjy schemes including replacement of submersible pump sets / panels / cables and other allied works required for functioning of tube well in all respect including one year defect liability period under jen section lohawat , phed bsr / 2022 23 / chapter 2 / 2.14 / supply& installationof single phase isl marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includesloweringof motor pump, installationof complete fitting & accessories, jointing of electrical cables up to switch board, testingofsubmersiblepumpsetandinterconnectionuptowatermains, complete in all respect. , 2.14.1 ) up to 2.0 kw , 2.14.2 ) above 2.0 kw , phed bsr / 2022 23 / chapter 2 / 2.15 / supply & installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , 2.15.1 ) up to 5.5 kw ( 7.5 hp ) & head up to 120 mtr. , 2.15.2 ) up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. , 2.15.3 ) 7.5 kw ( 10 hp ) & head up to 120 mtr. , 2.15.4 ) 7.5 kw ( 10 hp ) & head above 120 mtr , 2.15.5 ) 9.3 kw ( 12.5 hp ) & head up to 120 mtr. , 2.15.6 ) 9.3 kw ( 12.5 hp ) & head above 120 mtr. , 2.15.7 ) 11 kw ( 15 hp ) & head up to 120 mtr. , 2.15.8 ) 11 kw ( 15 hp ) & head above 120 mtr. , 2.15.9 ) 3 kw ( 17.5 hp ) & head up to 120 mtr. , 2.15.10 ) 13 kw ( 17.5 hp ) & head above 120 mtr. , 2.15.11 ) 15 kw ( 20 hp ) and above, head up to 120 mtr. , 2.15.12 ) 15 kw ( 20 hp ) and above, head above 120 mtr. , phed bsr / 2022 23 / chapter 2 / 2.16 / supply and fixing of electric feeder panel ( having projected canopy ) for submersible pump set single phase upto 5 hp, comprising of dol starter, mcb, indicating light, ammeter, volt meter, connection plate, condensers of approved make and the panel enclosure should be made out from 18 gauge m.s. sheet with powder coating. panel size height 600 mm width 500 mm depth 250 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the operation of panel should be suitable for on 240 volt ac supply. , phed bsr / 2022 23 / chapter 2 / 2.17 / supply and fixing of electric control feeder panel comprising of suitable rating mccb, dol starter, overload relay, ampere meter, volt meter, phase preventer, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 300mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 2.17.1 ) up to 5.00 hp , phed bsr / 2022 23 / chapter 2 / 2.18 / supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lightingarrangementetc. completesuitablefor threephasepumpset. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. , 2.18.1 ) above5 hpand upto 10 hp , 2.18.2 ) above 10 hp and up to 15 hp , 2.18.3 ) above 15 hp and up to 20 hp , 2.18.4 ) above 20 hp and up to 30 hp , phed bsr / 2022 23 / chapter 2 / 2.19 / supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. , 2.19.1 ) 3 core 4.0 sq.mm , 2.19.2 ) 3 core 6.0 sq.mm , 2.19.3 ) 3 core 10.0 sq.mm , 2.19.4 ) 3 core 16.0 sq.mm , phed bsr / 2022 23 / chapter 2 / 2.20 / supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. , 2.20.1 ) 10.0 sq.mm, 4 core , 2.20.2 ) 16.0 sq.mm, 4 core , 2.20.3 ) 25.0 sq.mm, 3.5 core , 2.20.4 ) 35.0 sq.mm, 3.5 core , phed bsr / 2022 23 / chapter 2 / 2.21 / plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , phed bsr / 2022 23 / chapter 2 / 2.22 / supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , phed bsr / 2022 23 / chapter 2 / 2.23 / supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. , 2.23.1 ) 125 mm dia , 2.23.2 ) 150 mm dia , 2.23.3 ) 200 mm dia , 2.23.4 ) 250 mm dia , phed bsr / 2022 23 / chapter 2 / 2.24 / providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. , 2.24.1 ) 32 mm dia , 2.24.2 ) 50 mm dia , 2.24.3 ) 65 mm dia , 2.24.4 ) 80 mm dia , phed bsr / 2022 23 / chapter 2 / 2.25 / providing & lowering in tube well isi marked hdpe pipe as per is 4984:1995 or amended upto date in pe 80 grade and class pn 10 of following dia. including hdpe / gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. , 2.25.1 ) 40 mm dia , 2.25.2 ) 50 mm dia , 2.25.3 ) 63 mm dia , 2.25.4 ) 75 mm dia , 2.25.5 ) 90 mm dia , phed bsr / 2022 23 / chapter 2 / 2.26 / providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. , 2.26.1 ) 50 mm dia , 2.26.2 ) 65 mm dia , 2.26.3 ) 80 mm dia , phed bsr / 2022 23 / chapter 2 / 2.27 / providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , phed bsr / 2022 23 / chapter 2 / 2.28 / providing and fixing of isi marked pvc storage tank of following capacity as per is: 12701 1989 ( of approved make ) with cover, 25 mm dia. 1 mtr long gi overflow pipe, 25 cm long 25 mm dia washout gi pipe with plug & socket, including p&f 32 mm dia ball cock ( float valve ) is 1703 marked with rod and pvc ball complete with brass weight 1000 gm, including p&f 15 mm dia ci quarter turn heavy duty bib cocks four nos. of superior quality and approved make, including interconnections complete job. , 2.28.1 ) 1000 litres capacity , 2.28.2 ) 2000 litres capacity , phed bsr / 2022 23 / chapter 2 / 2.29 / fabrication & fixing m.s. stand of specified class of angle iron lshaped of 50 mm size with four legs grouted by 300*300*300 mm cc block m 15 in the ground and all legs tied up with each other through same size of angle iron along with cross bars to support the bottom of 1000 ltr. / 2000 ltr. pvc tank complete in all respect. , phed bsr / 2022 23 / chapter 2 / 2.30 / providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes , 2.30.1 ) 65 mm dia , 2.30.2 ) 80 mm dia , phed bsr / 2022 23 / chapter 2 / 2.31 / proving and fixing 32 mm dia full way valve or wheel valve as per is:778 or amended up to date of approved make, on pump delivery pipe. , phed bsr / 2022 23 / chapter 2 / 2.32 / supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , phed bsr / 2022 23 / 2.34 providing and lowering of isi mark pvc u casing and screen pipe as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for tw and dcb with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. , 2.34.1 ) shallow well casing pipe ( cs ) suitable for depth up to 80 mtr. , 2.34.1.1 ) 150 mm nominal dia ( internal dia ) . , 2.34.1.2 ) 200 mm nominal dia ( internal dia ) . , 2.34.1.3 ) 250 mm nominal dia ( internal dia ) . , 2.34.2 ) medium well casing pipe ( cm ) suitable for depth above 80 mtr and up to 250 mtr. , 2.34.2.1 ) 100 mm nominal dia ( internal dia ) . , 2.34.2.2 ) 125 mm nominal dia ( internal dia ) . , 2.34.2.3 ) 150 mm nominal dia ( internal dia ) . , 2.34.2.4 ) 200 mm nominal dia ( internal dia ) . , 2.34.2.5 ) 250 mm nominal dia ( internal dia ) . , phed bsr / 2022 23 / 1.4 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 ( amended up to date ) with necessary jointing material like mechanical connectors, i.e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading / unloading charges, stacking of pipes, including cost of labour and material, specials ( tee, bend etc. ) , satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. ( excluding earth work ) . note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. supply may be in coil or straight length in 6 m / 12 m. , hdpe pe 80pn 6 , 75 mm dia , 90 mm dia , phed bsr / 2022 23 / chapter 6 / 6.1 / providing, lowering, aligning, fixing in position in pipe line, ci d / f sluice valves straight and pocket less body passage of approved make of following pressure rating & dia complete, confirfing to is:14846 ( amended up to date ) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210 / fg200 stem ss 304 , body seat ring, wedge facing ring & bushes ltb2 / ss , face to face dimensions as per is 14846 / 2000 ( amended up to date ) , epoxy ( non toxic suitable for drinking water ) applied inside and outside, flanges drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367 / cs / galvanised steel insersion rubber of black epdm 6mm thick . sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece / dismantling joints and earth work. , 6.1.1 manually operated ci sluice valve of class pn 1.0 , 6.1.1.1 80 mm hw , 6.1.1.2 100 mm hw...

Rajasthan State Road Transport Corporation - Rajasthan

35341587 tender for supply of tata spare parts & gear parts 1 2691 2620 7911 main shaft 2 2691 2620 0182 syncro kit 3 2688 2620 4608 shifter sleev 5 / 6 4 2691 2620 0186 m s gear 3rd 5 2691 2620 0187 m s gear 4th 6 2691 2620 4640 syncro body 5th 7 269126200172 assly coupling flange 8 2691 2620 4651 syncro ring 5 / 6 9 2691 2620 4621 syncro hub3 / 4 10 2691 2620 4618 syncro sleev3 / 4 11 2691 2620 4650 syncro ring2 / 3 12 2691 2620 4615 syncro hub 1 / r 13 2691 2620 0185 m s gear 2nd 14 2691 2620 0184 m s gear 1st 15 2691 2620 4616 eng.rev.gear fix dog 16 2691 2620 5413 m s rev. gear 17 2691 2620 8601 spacer 18 2691 2620 4312 circlip 19 2691 2620 4306 circlip 2.4 thik 20 2691 2620 4301 circlip 1.8 thik 21 2691 2620 4313 circlip gb 60 22 2691 2620 8612 main shaft spacer rev. gear 23 2691 2620 0135 drive pinion assy 24 2691 2620 7904 counter shaft 25 2691 2620 0146 m s gear 5th 26 2691 2620 4643 syncro cone 3 / 4 27 2691 2620 4645 syncro cone 5th 28 2691 2620 4623 syncro cone 29 2691 2620 4644 syncro cone 4th 30 2691 2620 8628 m s 4th gear washer gb60 31 2691 2620 4605 clutch body drive pinion 32 2691 2630 5424 c s gear 3rd 33 2691 2630 5425 c s gear 4th 34 2616 2635 6102 thrust washer rev idler gear 35 2691 2651 9901 brass pad 36 2688 2620 6501 lock nut 37 2691 2651 7909 rev.selector shaft 38 2691 2625 3113 gear box roller 39 2691 2630 5413 c s gear 6th 40 2691 2630 5414 c s gear 5th 41 2575 3530 5101 diff.spider tc bs iii 42 2668 3530 0107 / 130 c w pinion tc bs iii 43 2668 3530 5439 sun gear 44 2691 2630 3702 rr cover g.b hsg 45 269126205445 rv.main shaft gear bs iii 46 2770 3010 0138 accilator cable tata 47 8pk1422 fan belt tc 48 29967275 c.s.c rep. kit tvs 49 29967320 cmc rep kit tvs 50 cmc rod 51 rear hub shime [ thin&thick ] 52 rear hub makhi washer bsiii 53 257335308001 diff adj.screw big 54 14550603501 diff pinion lock ( a35*1.5 ) 55 3229940137 diff pinion wire lock 56 diff pinion star washer [ std 57 diff pionion shim [ th&thin ] 58 rear hub lock bolt w / n. bsiii59 rear hub check nut bsiii 60 diff pionion spacer washer 61 257635200110 diff. pinion flang 1510 62 0423530172 t diff. pinion nut 63 29190911 steel bush f / pin 911 64 257342108703 ret. sprring small 65 2576332100120 king pin perair kit 66 2576332106709 king pin std 67 257533203401 king pin bush 68 257633206707 king pin cotter pin 69 king pin th.washer set [ std 70 king pin rubber ring 71 king pin shim 72 front hub makhi washer 73 264126800224 sub ball assy small r / h 74 264126800225 sub ball assy small l / h 75 268846000121 drag link rep.kit 76 250726700138 sub ball assy big r.h&l / h 77 257326805101 self&shifter yoke 78 280826800106 gear lever assy gb 60 79 250726700152 sub assy ball shocket 80 3401 neadle bush 81 265146607702 sealing ring 82 280826800109 assy g.s lever kit gb 60 83 263026806703 pin assy con shifter yock 84 263026808601 spacer 85 m 14x1.5x45 hnager bolt 86 m 8x1.25 x 10 bolt coller type 87 m 14x1.5 eng.mtg. nut 88 m 16x1.5 threed arm nut 89 m 16x1.5x143 threed arm bolt 16x1.5x143 90 m 8x1.25x70 hex bolt m8x1.25x70 91 m 16x1.5x182 threed arm bolt m 16x1.5x182 92 m 10x1.5 nylock nut m10x1.5 93 m 10x1.5x30 bolt m 10x1.5x30 94 m22*2.5**110 rear hub bolt m22x2.5x110 95 1 1 / 2*70 hexa bolt 96 1 / 4x1 1 / 2 m.s.bolt &nut 97 3*1 / 4 or ( 4*1 / 4 ) m.s.bolt &nut 98 3 / 8*1 1 / 2 m.s.bolt &nut 99 m.s.& nyolock nut 5 / 16 100 m.s&nyolock nut 1 / 2 101 m.s&nyolock nut 1 / 4 102 1 / 4x1 1 / 2 t.v.s bolt&nyolock nut 103 all size m.s washer 104 1x5 / 16 m.s.bolt &nut 105 1 1 / 2x1 / 2 m.s.bolt &nut 106 4x3 / 8 m.s.bolt &nut 107 1 1 / 2x5 / 16 m.s.bolt &nut 108 4x5 / 16 m.s.bolt &nut 109 1x1 / 4 m.s.bolt &nut 110 12 mm a / comp coller nut 111 m 10x1.5x150 gear stand bolt 112 m 10x1.5x150 pressue plate bolt 113 m 8 x 1.25 x 90 bolt for fan supporter 114 26 x 26 comp. cooling elbow 115 5 / 16x1 1 / 2 t.v.s bolt&nyolock nut 116 10 no. nut & bolt 117 6 mm tvs bolt 118 5*20 gi bolt 119 accletor spring bsiii 120 cmc washer 121 cmc bracket 122 284829100122 c.m.c stell pipe 123 a / comp head cover 124 np 1029c fuel return steel pipe 125 brake chamber clip bolt 126 exaust pipe mouth ( turbo mouth ) 127 head shield plate bsiii 128 p / shaft center bearing plate 129 p / s center bearing bracket ( julla ) 130 a / comp head plate 131 tube fuel drain valve bsiii 132 263254209903 temperature switch 133 f / spindle check nut 134 pvc tube fuel drain pipe 135 12 mm air comp cock 136 air tank cock 137 thermostate elbow 138 cluth hsg lever washer 139 gear lever end rod 140 water cooling elbow bsiii 141 a / pressure pipe ddu to oil sep 142 tie rod rep kit 143 tie rod end ( r / l ) 144 brake shoe spring ( big ) 145 brake chamber spring 146 tie rod cap spring [ 4 rond ] 147 turing tube mouth assy ( gear lever mouth ) 148 gear box pin &bush set 149 clutch housing steel pathi 150 clutch housing bush big 151 air comp head packing bsiii 152 air comp stud nut 153 8x1.25mm f.i.pump nut 8x1.25mm 154 f.i.pump stud [ std / over size ] 155 283930100106 acc. rod w / end bsiii [ small&big ] 156 front eng mtg. washer 14 mm 157 acc.end small 158 acc.end big rh / lh 159 clutch rod pin 160 clutch rod p.v.c bush 161 clutch gear housing bush [ pin ] 162 front spring shackle washer 163 rear spring shackle washer 164 thick & thin gear box m / s shim 165 thick & thin gear box counter shim 166 air comp. head tee 167 278601999905 plug expension 168 clutch frok shaft big bsiii 169 clutch frok lever bsiii 170 dog bolt 171 gear lever shifting patti 172 spacer for main shaft od 173 gear shifting lever fork 174 g / box chira pin gb 60 175 benjo washer all size 176 bengo bolt all size 177 head valve seal tata midi 178 f.i.copper washer midi 179 npn rivets set long 180 206032103203 front center bolt 10 181 11084112854 rear center bolt 10 182 257632204201 front spring u bolt 10 183 259932504201 reae spring u bolt 14 184 npn rear spring u bolt 16 185 rear spring u bolt 15 186 27543210 rear spring center bolt bsiii 187 261832403202 rear spring center bolt 12 188 3523200063 front spring shackle tatat 189 3523200163 rear spring shackle 190 423270401 front spring braket tata 191 3523250101 rear spring braket 192 3523220530 front spring shackle pin 193 3523250530 rear spring shakle pin 194 3523259530 rear spring shackle 195 3523220050 front spring main leaf bush 196 3223250150 rear spring main leaf bush 197 26314020678 wedge scerw 198 263241100117 u j cross assy bsiii 42x120 199 278607989948 tube fuel drian small 200 8 mm radiatore hose pipe 6&8 mm 201 air comp house 202 oil gauge bsiii 203 hose pipe clip 000 204 hose pipe clip oom 205 12 mm water colling hose 12mm 206 np 1412 oil guge cover bsiii 207 air clener r / ring 208 278650105845 radiator over flow rubbe hose ( r2149 / r2506d ) 209 hose air clener [ cobra ] bsiii 210 hose pipe clip tb 54 211 oil cap bsiii 212 p.v.c joint [ 4 to 15mm ] 213 6 mm air pressure nylone pipe bsiii 214 12to 15 mm air pressure nylone pipe bsiii 215 king pin rubber ring 216 a / comp o ring bsiii 217 a / comp head steel pipe 218 np 1020 oil pressure pipe 219 np 1018 air comp r / hose 220 np 1199 al air comp pipe 221 eng comp head tee i type 222 eng head tee l type 223 r 2367 z type hose ( r 2367 ) 224 diesel rubber hose 10mm 225 oil &tappite cover r / hose 226 np 1025 oil pressuer pipe np 1025 227 257641300301 prop shaft rubber pad bsiii 228 207746800154 return hose assy ] p / str. ] np 1370 229 207746800156 power steering rub.hose pipe ( np 1371 ) 230 207746800157 suction line hose 231 0005000106 j radiator cap 232 278650105819 stype hose 233 timming pin ( pvc ) 234 s / a pin 235 s / a bush 236 greese cap 237 278650105835 ltype hose 238 311828 spl prop shaft mid stub shaft tata 239 msp3 / 75 rep.kit 240 m sp 6 / 8 rep.kit 241 278601999918 seal rectangular ring 242 278601989934 breather crank case 243 278607996904 tube fuel supply 244 278607999916 spacer mounting 245 220014105302 gasket cover plate 246 278607996905 tube fuel supply 247 278614605802 hose hump 248 14280599361 hose clamp sltb70sae j1508 249 207609135884 rubber hose turbo 250 14280599272 hose clamp sltb72sae j1508 251 278614999967 gaskit turbocharger 252 278614999904 stud m10x1.5x42 253 278614999927 clamp tube 254 278614999931 clamp v band 255 278620999995 fan , engine with clutch 256 207615999902 pulley fan ratio 1.2:1 257 278614999914 hex flange head cap m10x1.5 258 278620999919 connection, water inlet 259 278620990150 connection, water outlet 260 278620999920 hex flange head cap m10x1.5x75 261 278620999910 seal rectangular ring 262 278620990220 water pump 263 207609130320 assly flanged pipe for natural as per af 264 278609130134 assly air filter offer drg 265 277024105101 engine mounting arm rh front 266 277024105102 engine mounting arm lh front 267 257624100101 engine mounting pad front 268 3522420509 torque support 269 257624200118 engine mounting rear 270 275425103401 bush 271 275225400110 release bearing tc1512 272 275425605101 clutch release yoke 6bt 273 275425605901 key clutch release yoke 274 275425607901 cross shaft 275 250526706009 shifting lever 276 277026810101 assly bracket gear shift liver mtg 277 269126710109 assly bracket 278 264126807925 link rod 279 264126800225 assly ball joint 280 264126800224 assly ball joint rh thread 281 250726700152 sub assly ball and socket joint big 282 280826800109 assly gear shifter leverw / selector 283 683929100105 assly clutch fluid reservior with clamp rh 284 216329150102 assly tube ( 6odx3160lg ) 285 207729150111 asly connecting line ( hyd. clutch ) 286 280829100109 assly clutch padle lever complete 287 278229308701 return spring 288 280829100112 assly cmc 289 275432103201 center bolt 290 12051501207 hex nut m12 291 277032103401 spring bush 292 277032204203 u bolt l 280 293 3423220084 caster plate lh 294 275432107101 caster plate rh 295 3523200063 assly spring shakle 296 257632207701 rubber buffer 297 257632203701 guide plate front 298 2599325042001 u clamp 299 3523200163 assly spring shakle rear 300 257533409201 thrust washer 301 257633407801 oil seal front hub 302 284633990110 kit threaded end lh 303 284633990111 kit threaded end rh 304 257633206709 king pin std 305 257533203401 bush king pin 306 257633208601 spacer front 307 288042108702 spring abutment end for front brk 308 277842138701 spring full of cam end 309 257342107702 o ring 310 npn delrin bush 311 288042107801 oil seal 312 257342108405 sleeve slack adjuster end 313 263243700109 dual brake valve voss 314 npn assly base plate rhd ( dual tradle vlv mtg. ) 315 263243700155 four circuit protection valve 316 278243700147 relay valve 317 209346400102 assly steering wheel with out emblem 318 206746600105 assly universal joint 319 263246000013 drag link assly 320 278244400101 assly hydraulic steering tank plastic 321 276349205301 gaskit exhaust pipe flange 322 131549000045 assly flexible exhaust pipe 323 278650105851 hose radiator to water pump 324 14280598217 hoseclamp tb54 saej1508 325 278650100331 assly reserve tank 326 257450009202 washer ( 47 dia ) 327 257450006301 rubbber buffer 328 278550406901 tube radiator mtg ( 59lg ) 329 278603997702 oil seal 330 278607990134 pump fuel transfer 331 278607999930 screw benjo connector m 14x1.5x26 332 278620999823 dapter engine vent 333 npn compressor air inlet adaptor 334 npn threaded ring lh for crown std 335 npn threaded ring lh for crown i st over size 336 npn threaded ring rh for crown 337 npn threaded ring rh for crown i st over size 338 npn threaded ring center pinion for crown 339 321 265 0805 selector shaft ist speed gb 40 340 321 265 1805 selector shaft 2 / 3rd speed gb 40 341 321 265 1905 selector shaft 4 / 5th speed gb 40 342 322 265 0305 selector shaft reverse 343 322 265 0123 gear shift dog 1st gear 344 321 265 1205 selector fork 2 / 3rd 345 2505 2651 5102 selector fork 4 / 5th 346 321 265 1301 selector fork 1st 347 2505 2651 5101 selector fork reverse 348 2505 2671 3756 top cover 349 2505 2670 5104 shifting finger 350 2505 2670 7908 selector & shifter shaft 351 2507 2670 6014 shifting lever 352 2505 2625 7910 drive shaft 353 340 262 0134 syn. ring 354 2505 3015 5403 syn. sleeve 4 & 5th 355 2505 2620 3802 syn. cone 356 321 262 0823 shifting sleeve 357 2505 3015 0105 assy. helical gear 4th speed 358 322 260 0644 assy. helical gear 3rd 359 322 262 0435 syn. sleeve 2 / 3rd 360 322 262 0112 helical gear 2nd ( t 32 ) 361 322 263 0333 reverse gear main shaft 36t 362 321 262 0723 shifter sleeve 1st 363 2505 3015 5401 gear wheel 1st speed t 39 364 2505 2620 0176 gear drive oil slinger 365 2505 2620 7902 drive shaft ( speed drive ) bs iv 366 2505 2630 7906 counter shaft 367 2505 2630 5414 2nd gear counter shaft 368 2505 2630 5415 3rd gear counter shaft 23t 369 2505 3014 5401 4th gear on counter shaft 370 2505 3014 5402 constant mesh gear 371 2505 2635 0106 assy. reverse idler gear ( en 36 ) 372 2505 3017 7901 reverse idler gear shaft 373 8854 2604 1612 syn. kit 374 2630 2680 8601 spacer 375 2786 0399 0196 assy. fly wheel with ring gear tatabs iii 376 2786 0399 9972 fly wheel housing 377 2525 0311 0141 assy. fly wheel with ring gear tatabs iv 378 2691 2630 7901 counter shaft g600 379 2505 2620 7903 main shaft bs iv 380 352 0321 105 ring gear bs iv 381 2786 0399 5402 gear flywheel ring bs iii 382 2575 3530 5101 differential spider bs iv 383 207341115101 coupling flange pro. shaft bs iii 384 245041115103 flange yoke bsiii / bsiv 385 npn stub shaft tata bsii with yoke 386 msp 1 / 505 major overhaul kit air comp wabco 387 msp 1 / 509 ring kit air comp wabco 388 msp 2 / 37 repair kit clutch booster wabco 389 msp 1 / 503 heat gaskit wabco 390 m848650 / 51 diaphragm rubber wabco 391 269126707903 selector & shifter shaft rhd bs1 / 2 / 3 / 4 392 269126715101 shifter finger 393 251626713805 cover 394 251626715302 gaskit side cover 395 2505267060009 shifting liver bs1 / 2 / 3 / 4 396 250526717701 bellow 397 269126710130 assly top cover complete bs 2 / 3 / 4 398 251626713705 gear case cover top ( upper half ) 399 909 / 11090108 acclerator cable assly tata 3118 ( both side thread ) k 1236 400 npn sleeve of wabco air compressor for tata bsiii 401 npn sleeve of knorr brimes air compressor k017827 / 531933 / lk3883 for tata bsiii 402 npn sleeve of wabco air compressor ( 100101030 ) for eicher 10.75 403 npn sleeve of wabco air compressor ( 9129700090 ) for tata bsiv 404 b31tm100583 head top gaskit packing knor birms air compressor 405 b31tm100584 head top cover plate knor birms air compressor 406 b31tm100585 head top reed plate knor birms air compressor 407 b31tm1008582 knor birms air compressor piston and ring assembly 408 b31tm1009806 knor birms air compressor pump support back plate...

Rajasthan State Road Transport Corporation - Rajasthan

34997905 tender for auto motive gasket ( essential ) pgk / 12 2576 3560 5301 gasket ( cover to hub ) bs iv / bs iii, 2017 3 pgk / 15 2573 3511 5302 gasket bs iii ( diff. cover ) 4 pgk / 29 f1730200 axle shaft packing leyland caf 1mm bs iii 5 pgk / 42 f1761300 gasket nozzle holder bs iii 6 pgk / 47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii 7 pgk / 65 ia 203036 rear axle packing eicher midi 1mm caf 8 pgk / 66 f1762900 rear axle packing leyland midi1mmcaf 9 2525 0114 6301 gasket push for chamber cover bs iv 10 2525 1411 0136 assy gasket ( exhaust manifold ) bs iv 11 2525 1411 0135 assy gasket exhaust manifold bs iv 12 2786 1499 5301 gasket exhaust manifold bs iii 2017 13 3521 188 0780 gasket oil cooler bs iv 14 2786 0999 9962 gasket filter head bs iv / iii / 2017 / 15 2786 1899 9910 gasket lube cooler bs iv / iii / 2017 16 216549205301 gasket exhaust system 17 276349205301 gasket exhaust pipe flange bs iii / iv...

Rajasthan State Road Transport Corporation - Rajasthan

33554618 rsrtc invites the tender for automotive gasket essential rsrtc invites the tender for automotive gasket essential , auto motive gasket (essential)as:284:71:dec:2006 , pgk/12 2576 3560 5301 gasket ( cover to hub) bs iv/bs iii,2017 , pgk/15 2573 3511 5302 gasket bs iii( diff. cover) , pgk/29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk/42 f1761300 gasket nozzle holder bs iii , pgk/47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk/65 ia 203036 rear axle packing eicher midi 1mm caf , pgk/66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv/iii/2017/ , 2786 1899 9910 gasket lube cooler bs iv/iii/2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii/iv , pgk/78 fs3091dsxna head gasket...

Public Health And Engineering Department - Rajasthan

33413220 supply installation and commissioning of solar panels for running of motor pumps at mandhla under sub dn ramgarh with 3 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at mandhla under sub dn ramgarh with 3 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning of mnre approved off grid solar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms frame and foundation on ground/roof of pump house or cwr, showing arrangement of panel in available space, installation of pv module on ms frame as per approved design and drawings. mounting structure shall be suitably design to withstand wind velocity up to 150km/hr. the work shall be executed as per detailed technical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structure and suitable provision shall be included in tender document. , at mithatala , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking (mppt) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on/off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. ac submerssible pump sets +individual solar pump controllerwith maximum power point tracking (mppt) , 5.0 hp , supply, installation, testing and commissioning of remote monitoring unit on off grid solar controller for remote on/off, parameter setting, monitoring and troubleshooting through mobile etc. complete. web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of engineer. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.25.0 sq.mm, 3.5 core , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged (welded) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064/1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box (sheet 16 swg) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer ,nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1/2 (for installation pressure gauge) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , providing and fixing of flanged/ plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level/ depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of engineer incharge.ms pipe specials upto 600mm dia (with minimum 5mm thickness sheet) , providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. , providing and fixing of isi marked pvc storage tank of following capacity as per is: 12701 1989 (of approved make) with cover, 25 mm dia. 1 mtr long gi overflow pipe, 25 cm long 25 mm dia washout gi pipe with plug & socket, including p&f 32 mm dia ball cock (float valve) is 1703 marked with rod and pvc ball complete with brass weight 1000 gm, including p&f 15mm dia ci quarter turn heavy duty bib cocks four nos of superior quality and approved make, including interconnections complete job. 2000 litres capacity , fabrication & fixing m.s. stand of specified class of angle iron l shaped of 50 mm size with four legs grouted by 300*300*300 mm cc block m 15 in the ground and all legs tied up with each other through same size of angle iron along with cross bars to support the bottom of 1000 ltr./ 2000 ltr. pvc tank complete in all respect. , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs /rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month.(forrural scheme where three phase electric supply is up to 8 hrs) 7.3.10.5 hp to 5.0 hp...

Rajasthan State Road Transport Corporation - Rajasthan

32614525 rsrtc invites the tender for automotive gasket essential rsrtc invites the tender for automotive gasket essential , auto motive gasket ( essential ) as:284:71:dec:2006 , pgk / 12 2576 3560 5301 gasket ( cover to hub ) bs iv / bs iii, 2017 , pgk / 15 2573 3511 5302 gasket bs iii ( diff. cover ) , pgk / 29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk / 42 f1761300 gasket nozzle holder bs iii , pgk / 47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk / 65 ia 203036 rear axle packing eicher midi 1mm caf , pgk / 66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold ) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv / iii / 2017 / , 2786 1899 9910 gasket lube cooler bs iv / iii / 2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii / iv , pgk / 78 fs3091dsxna head gasket...

Public Health And Engineering Department - Rajasthan

32281446 supply installation and commissioning of solar panels for running of motor pumps at mithatala under sub dn ramgarh with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at mithatala under sub dn ramgarh with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning ofmnre approved off gridsolar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms fabricated structure 120 micron hot dip galvanized iron , showing arrangement of panel in available space and installation ofpv module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. the foundation of structure shall be in rcc. mountingstructure shall be suitably designedto withstand wind velocity up to 150km / hr. the work shall be executed as perdetailedtechnical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structureandsuitable provision shall be included in tender document. , at mithatala , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking ( mppt ) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on / off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation ) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. , 5.0 hp , supply, installation, testing and commissioning of remote monitoring unit on off grid solar controller for remote on / off, parameter setting, monitoring and troubleshooting through mobile etc. complete. web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of engineer. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.25.0 sq.mm, 3.5 core , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , providing and fixing of flanged / plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level / depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of engineer incharge.ms pipe specials upto 600mm dia ( with minimum 5mm thickness sheet ) , construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. the plinth area of pump house shall be area of measurement. , construction of boundary wall of brick / stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. , providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. , supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , 9.3 kw ( 12.5 hp ) & head up to 120 mtr. , 11 kw ( 15 hp ) & head up to 120 mtr , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month. ( forrural scheme where three phase electric supply is up to 8 hrs ) 7.3.10.5 hp to 5.0 hp...

Public Health And Engineering Department - Rajasthan

32281435 supply installation and commissioning of solar panels for running of motor pumps at mandhla under sub dn ramgarh with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at mandhla under sub dn ramgarh with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning ofmnre approved off gridsolar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms fabricated structure 120 micron hot dip galvanized iron , showing arrangement of panel in available space and installation ofpv module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. the foundation of structure shall be in rcc. mountingstructure shall be suitably designedto withstand wind velocity up to 150km / hr. the work shall be executed as perdetailedtechnical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structureandsuitable provision shall be included in tender document. , at mandhla , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking ( mppt ) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on / off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation ) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. , 5.0 hp , supply, installation, testing and commissioning of remote monitoring unit on off grid solar controller for remote on / off, parameter setting, monitoring and troubleshooting through mobile etc. complete. web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of engineer. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.25.0 sq.mm, 3.5 core , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , providing and fixing of flanged / plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level / depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of engineer incharge.ms pipe specials upto 600mm dia ( with minimum 5mm thickness sheet ) , construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. the plinth area of pump house shall be area of measurement. , construction of boundary wall of brick / stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. , providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. , supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , 7.5 kw ( 10 hp ) & head up to 120 mtr. , 5.5 kw ( 7.5 hp ) & head up to 120 mtr. , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month. ( forrural scheme where three phase electric supply is up to 8 hrs ) 7.3.10.5 hp to 5.0 hp...

Public Health And Engineering Department - Rajasthan

32281430 supply installation and commissioning of solar panels for running of motor pumps at gairaja under sub dn ramgarh with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at gairaja under sub dn ramgarh with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning ofmnre approved off gridsolar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms fabricated structure 120 micron hot dip galvanized iron , showing arrangement of panel in available space and installation ofpv module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. the foundation of structure shall be in rcc. mountingstructure shall be suitably designedto withstand wind velocity up to 150km / hr. the work shall be executed as perdetailedtechnical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structureandsuitable provision shall be included in tender document. , at gairaja , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking ( mppt ) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on / off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation ) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. , 5.0 hp , supply, installation, testing and commissioning of remote monitoring unit on off grid solar controller for remote on / off, parameter setting, monitoring and troubleshooting through mobile etc. complete. web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of engineer. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , providing and fixing of flanged / plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level / depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of engineer incharge.ms pipe specials upto 600mm dia ( with minimum 5mm thickness sheet ) , construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. the plinth area of pump house shall be area of measurement. , construction of boundary wall of brick / stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. , providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. , supply & installation of 3 phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , 9.3 kw ( 12.5 hp ) & head up to 120 mtr. , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month. ( forrural scheme where three phase electric supply is up to 8 hrs ) 7.3.10.5 hp to 5.0 hp , 35239.06...

Public Health And Engineering Department - Rajasthan

32281164 supply installation and commissioning of solar panels for running of motor pumps at jawaharnagar under project sub dn jaisalmer with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at jawaharnagar under project sub dn jaisalmer with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning ofmnre approved off gridsolar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms fabricated structure 120 micron hot dip galvanized iron , showing arrangement of panel in available space and installation ofpv module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. the foundation of structure shall be in rcc. mountingstructure shall be suitably designedto withstand wind velocity up to 150km / hr. the work shall be executed as perdetailedtechnical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structureandsuitable provision shall be included in tender document. , at jawaharnagar , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking ( mppt ) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on / off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation ) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. , 7.5kw ( 10.0 hp ) , supply, installation, testing and commissioning of remote monitoring unit on off grid solar controller for remote on / off, parameter setting, monitoring and troubleshooting through mobile etc. complete. web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of engineer. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.25.0 sq.mm, 3.5 core , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , providing and fixing of flanged / plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level / depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of engineer incharge.ms pipe specials upto 600mm dia ( with minimum 5mm thickness sheet ) , construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. the plinth area of pump house shall be area of measurement. , construction of boundary wall of brick / stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. , providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month. ( forrural scheme where three phase electric supply is up to 8 hrs ) 7.3.30.8 hp to 10.0 hp...

Public Health And Engineering Department - Rajasthan

32281157 supply installation and commissioning of solar panels for running of motor pumps at namdev sansthan kishanghat under project sub dn jaisalmer with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at namdev sansthan kishanghat under project sub dn jaisalmer with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning ofmnre approved off gridsolar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms fabricated structure 120 micron hot dip galvanized iron , showing arrangement of panel in available space and installation ofpv module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. the foundation of structure shall be in rcc. mountingstructure shall be suitably designedto withstand wind velocity up to 150km / hr. the work shall be executed as perdetailedtechnical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structureandsuitable provision shall be included in tender document. , at kishanghat , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking ( mppt ) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on / off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation ) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. , 3.7kw ( 5.0 hp ) , 10.8 providing, installation, testing and commissioning structural steel work riveted or bolted in built up sections, trusses and framed work, including cutting, hoisting for following staging and capacity of rotational moulded polyethylene water storage tank on it as per indicative drawing given in the bid document. on thepolyethylene tanks, there shall be provision of suitable space for installation of solar panels up to 5.0 kw and further additional 2.5 kw on the side of steel structure if required as per indicative drawing. cost of solar panels is not included in this item . the structural steel shall be 120 micron hot dip galvanized iron and foundation of structure shall be in rcc with minimum depth as 2.0 mtr ( other than rocky strata ) . the work includes p and f of polyethylene water storage tank ( is: 12701, isi marked, indicating the bis license no. ) of approved make with cover. providingandfixing 50 mm dia isi marked g.i. class b pipe for inlet, outlet and over flow pipe and 32 mm gi class b pipe for wash out with gm gate valves at inlet and outlet pipe including making connection etc. complete as per drawing, technical specification and direction of engineer in in charge. the scope includes inlet gi pipe from ground level to water tank and outlet pipe from water tank to ground and up to 2.0 mtr away from foundation and overflow pipe is to be interconnected in distribution pipe line. wash out pipe shall be taken up to a suitable point minimum 5.0 mtr away from tank. water level controller shall installed to monitor level in tank and shall automatically shut off motor when tank is filled .0.8.15000 liter x 2 nos. pe water tank, staging 10 meter. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month. ( forrural scheme where three phase electric supply is up to 8 hrs ) 7.3.10.5 hp to 5.0 hp...

Public Health And Engineering Department - Rajasthan

32281149 supply installation and commissioning of solar panels for running of motor pumps at sadrau under project sub dn jaisalmer with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer supply installation and commissioning of solar panels for running of motor pumps at sadrau under project sub dn jaisalmer with 5 year o and m of whole solar system including tubewell etc. under distt. div. jaisalmer , supply, installation, testing and commissioning ofmnre approved off gridsolar panels for running of motor pumps with 25 years of linear generation warranty, work includes designing of solar panel area and ms fabricated structure 120 micron hot dip galvanized iron , showing arrangement of panel in available space and installation ofpv module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. the foundation of structure shall be in rcc. mountingstructure shall be suitably designedto withstand wind velocity up to 150km / hr. the work shall be executed as perdetailedtechnical specifications, approved drawing and direction of engineer in charge. note: there shall be 5 year service warranty for solar panel and mounting structureandsuitable provision shall be included in tender document. , at sadrau , providing, installation, testing and commissioning of ac submerssible pump sets with inbuilt or individual solar pump controllerwith maximum power point tracking ( mppt ) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day. solar pumpshall be of stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope . pump controller shall have adequate protection against dry operation of motor pump set, and against hails and storms. full protection against open circuit, accidental short circuit and reverse polarity should be provided. a good reliable on / off switchbe provided. the cable shall be isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date ( standard insulation ) and conductor as per class 5 of is 8130:1980 or amended up to date. the duty condition of pump set shall be as per scope of work and entire work shall be executed as per technical specification and direction of engineer in charge. , 7.5kw ( 10.0 hp ) , supply, installation, testing and commissioning of remote monitoring unit on off grid solar controller for remote on / off, parameter setting, monitoring and troubleshooting through mobile etc. complete. web charges and data charges for 5 year during service warranty etc. complete in all respect as per technical specification and as per direction of engineer. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , providing & laying isi marked gi pipe “a” class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & fixing of isi marked three core pvc flat submersible cable as per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980 including making connection etc. 3 core 6.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size.25.0 sq.mm, 3.5 core , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 65 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 65 mm dia , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 250 mm dia , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes. 65 mm dia , providing and fixing of flanged / plain ended ms specials made from ms sheet strips of relevant is specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level / depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of engineer incharge.ms pipe specials upto 600mm dia ( with minimum 5mm thickness sheet ) , construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. the plinth area of pump house shall be area of measurement. , construction of boundary wall of brick / stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. , providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamel paints. , maintenance of tubewells which includes round the clock monitoring oftubewells of all sizes, completerepairs / rewinding ofsubmersible pumpsets including cost ofmaterial components required to repair pumpsets, starters, meters etc. of electric panel of tube wells, lowering and unlowering of pumpsets complete in all respect, maintenance of log booksandhistroy sheetas directed by engineer in charge for tubewell per month. ( forrural scheme where three phase electric supply is up to 8 hrs ) 7.3.30.8 hp to 10.0 hp...

North Western Railway - Rajasthan

32261154 supply of u bend pipeu bend pipe,u bend pipe ( flange flange) as per elgi part no. 07031506a for compressor model no .rr 15070....

Rajasthan State Road Transport Corporation - Rajasthan

32195400 rsrtc invites the tender for automotive gasket essential rsrtc invites the tender for automotive gasket essential , auto motive gasket ( essential ) as:284:71:dec:2006 , pgk / 12 2576 3560 5301 gasket ( cover to hub ) bs iv / bs iii, 2017 , pgk / 15 2573 3511 5302 gasket bs iii ( diff. cover ) , pgk / 29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk / 42 f1761300 gasket nozzle holder bs iii , pgk / 47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk / 65 ia 203036 rear axle packing eicher midi 1mm caf , pgk / 66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold ) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv / iii / 2017 / , 2786 1899 9910 gasket lube cooler bs iv / iii / 2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii / iv , pgk / 78 fs3091dsxna head gasket...

Public Health Engineering Department - Rajasthan

31857475 annual rate contract for commissioning of sources under phed city dn. barmer 2 testing verticality of tube well by plumbing system and yield test and draw down test by pumping system as per is : 2800 ( part – ii ) – 1979 or as per amended up to date. 3 supplying & packingp gravel suitable for slot size / mesh size as suggested in is 2800 ( part 1 ) 1991 or as per amended up to date. 4 development of tube well having depth up to 250 mtr as per is: 11189 1985 and is: 2800 ( part i ) 1991 ( both amended up to date ) using suitable methods to give sand free water for required yield of the gravel packed tube well. 5 supply of erw m.s. black casing pipe isi marked ( is: 4270 / 2001 ) or amended up to dateoffollowing sizes200 mm dia nb ( thickness of pipe 5.0 mm & mass of tube 20.13 kg / m ) 6 250 mm dia nb ( thickness of pipe 7.1 mm & mass of tube 46.57 kg / m ) 7 labour charges for making slots on blank pipes made of erw ms black pipe isi marked of following sizes, the slotting should be as per is:8110 1985.200 mm dia nominal bore of 4.8 mm thickness 8 250 mm dia nominal bore of 7.1mm thickness 9 supply of isi mark ac pressure pipe class 15 manufactured by mazza process as per is:1592 2003 or amended upto date, for casing of tube wellfor following dia nominal bore, with jointing material pvc coupler as per technical specification and direction of engineer in charge. 200 mm nominal dia 10 250 mm nominal dia 11 300 mm nominal dia 12 making slots of hole size and nos. as directed by eic in ac pressure pipe class 15 as per technical specification for using slotted pipe in tw casing. 13 providing and lowering of isi mark pvc u casing and screen pipe as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for tw and dcb with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. shallow well casing pipe ( cs ) suitable for depth up to 80 mtr. 200 mm nominal dia ( internal dia ) . 14 250 mm nominal dia ( internal dia ) . 15 medium well casing pipe ( cm ) suitable for depth above 80 mtr and up to 250 mtr. 100 mm nominal dia ( internal dia ) . 16 200 mm nominal dia ( internal dia ) . 17 250 mm nominal dia ( internal dia ) . 18 providing & laying isi marked gi pipe light duty ( “a” class ) as peris: 1239for casing pipe for submersible cable external work 40 mm dia complete in all respect. 19 supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. up to 5.5 kw ( 7.5 hp ) & head up to 120 mtr. 20 up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. 21 7.5 kw ( 10 hp ) & head up to 120 mtr. 22 7.5 kw ( 10 hp ) & head above 120 mtr. 23 9.3 kw ( 12.5 hp ) & head up to 120 mtr. 24 9.3kw ( 12.5 hp ) & head above 120 mtr. 25 11 kw ( 15 hp ) & head up to 120 mtr. 26 11 kw ( 15 hp ) & head above 120 mtr. 27 13 kw ( 17.5 hp ) & head up to 120 mtr. 28 13 kw ( 17.5 hp ) & head above 120 mtr. 29 15 kw ( 20 hp ) and above, head up to 120 mtr. 30 15 kw ( 20 hp ) and above, head above 120 mtr. 31 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. above 5 hp and up to 10 hp 32 above 10 hp and up to 15 hp 33 above 15 hp 34 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc.3 core 4.0 sq.mm 35 3 core 6.0 sq.mm 36 3 core 10.0 sq.mm 37 3 core 16.0 sq.mm 38 supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 10.0 sq.mm, 4 core 39 16.0 sq.mm, 4 core 40 25.0 sq.mm, 3.5 core 41 35.0 sq.mm, 3.5 core 42 plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. 43 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 44 supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 125 mm dia 45 150 mm dia 46 200 mm dia 47 250 mm dia 48 providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 32 mm dia 49 50 mm dia 50 65 mm dia 51 80mm dia 52 providing & lowering in tube well isi marked hdpe pipe as per is 4984:1995 or amended upto date in pe 80 grade and class pn 10 of following dia. including hdpe / gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. 40 mm dia 53 50 mm dia 54 63 mm dia 55 75 mm dia 56 90 mm dia 57 providing & fixing pump safety cage as per specifications or as directed by engineer in charge. 58 providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes 65 mm dia 59 80 mm dia 60 proving and fixing 32 mm dia full way valve or wheel valve as per is:778 or amended up to date of approved make, on pump delivery pipe. 61 supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg.including all jointing material as per specification with safety cover. 62 6.8 providing, lowering, aligning, fixing in position in pipe line at work site, di d / f resilient seated ( soft seated ) sluice valves ( gate valves ) , vacuum tight ( bubble tight ) , straight and pocket less body passage of approved make of following class & dia complete confirming to bs en 1171 / awwa c 509 and of following specifications: body & bonnet of ductile cast iron of grade ggg40 / ggg50 as per din 1693 or gr sg 400 / 12 as per is 1865 or equivalent grade as per is :3896 part2 1985 and subsequent revisions, wedge of same material as body & shall vulcanisedrubber lined with epdm ( food grade quality ) and seals of nbr face to face dimensions as per bs 5163 89 / is 14846 / 2000 ( amended up to date ) / din 3202 f4, stem / spindle of ss ( aisi 316 or equivalent ) electrostatic epoxy powder ( ep p ) / fusion bond epoxy ( non toxic suitable for drinking water ) coated with minimum thickness of 250 microns inside and outside, drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367 ( galvanised steel ) insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic, sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece / dismantling joints and earth work.manually operated resilient seated sluice valves of class pn 1.0 / 1.6 63 80 mm dia 64 100 mm dia 65 ruidp sor 2017 items 66 p&f tp&n 415 v metal clad hbc cum rewire able switch fuse unit with porcelain kit kat & neutral link and conforming to is:13947 p i&iii and making connections with lugs testing etc. as required. group 2 67 32amp rating 68 63 amp rating 69 100 amp rating 70 p&f tp&n 415 v side handle operated double break fuse switch unit in sheet steel enclosure conforming to is: 13947 p iii and is:4064 ( w / o hbc fuses ) including making connections with suitable lugs, testing etc. as required. group 2 71 200amp rating 72 300 / 320 amp rating 73 p&f 240 / 415 v porcelain kitkat fuse conforming to is:2086, 1983 0n existing board / sheet including making connections with lugs, testing etc. as required group 2 74 32a, 415v 75 63a, 415v 76 100a, 415v 77 200a, 415v 78 300 / 320a, 415v...

Public Health Engineering Department - Rajasthan

31710346 procurement and installation of centrifugal, monoblock and submersible pump sets and panel starter of different capacity complete job at various schemes district jhalawar. procurement and installation of centrifugal, monoblock and submersible pump sets and panel starter of different capacity complete job at various schemes district jhalawar. , ( a ) supply & installation of submersible pump set with panel starter , supply & installation of 3 phase isi marked submersible motor pump set ofthree star or better rating of beeand as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect.11 kw ( 15 hp ) & head above 120 mtr. ( 12nos motor pump set ) phed bsr 2021 2.15.8 , supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. above 10 hp and up to 15 hp phed bsr 2021 2.18.2 , providing & lowering in tube well isi marked gi pipe medium duty ( “b class ) , steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 50 mm dia phed bsr 2021 2.24.3 , ( b ) other miscellaneous items , providing, installation, testing and commissioning of submersible monoblock pump set conforming to is 8034 and motor conforming to is 9283, with water proof winding. pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415 v ± 10%, 3 ph, 50 hz ac and with water lubricated bearing to accept entire hydraulic thrust. supply, with cable guard, thrust carbon / fiber bearing to withstand entire hydraulic thrust. the pump set shall be suitable for direct coupling, with suitable suction strainer. pump should have suitable discharge out let as per manufacturers design. antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. completein all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions mentioned in td. 3.7 kw ( 5.0 hp ) ( phed bsr 5.5.2 / 2021 ) , supply & installation of single phase isi marked submersible motor pump set of three star or better rating of bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. up to 2.0 kw. ( phed bsr 2.14.1 / 2021 ) , supply and fixing of electric feeder panel ( having projected canopy ) for submersible pump set single phase upto 5 hp, comprising of dol starter, mcb, indicating light, ammeter, volt meter, connection plate, condensers of approved make and the panel enclosure should be made out from 18 gauge m.s. sheet with powder coating. panel size height 600 mm width 500 mm depth 250 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete platform. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the operation of panel should be suitable for on 240 volt ac supply. ( phed bsr 2.16 / 2021 ) , supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 3 core 4 sqmm ( phed bsr 2.19.1 / 2021 ) , providing, installation, testing and commissioning of submersible monoblock pump set conforming to is 8034 and motor conforming to is 9283, with water proof winding. pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415 v ± 10%, 3 ph, 50 hz ac and with water lubricated bearing to accept entire hydraulic thrust. supply, with cable guard, thrust carbon / fiber bearing to withstand entire hydraulic thrust. the pump set shall be suitable for direct coupling, with suitable suction strainer. pump should have suitable discharge out let as per manufacturers design. antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. completein all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions mentioned in td. 9.3 kw ( 12.5 hp ) ( phed bsr 5.5.5 / 2021 ) ...

Rajasthan State Road Transport Corporation - Rajasthan

31330058 rsrtc invites the tender for automoitve gasket rsrtc invites the tender for automoitve gasket , auto motive gasket ( essential ) as:284:71:dec:2006 , pgk / 12 2576 3560 5301 gasket ( cover to hub ) bs iv / bs iii, 2017 , pgk / 15 2573 3511 5302 gasket bs iii ( diff. cover ) , pgk / 29 f1730200 axle shaft packing leyland caf 1mm bs iii , pgk / 42 f1761300 gasket nozzle holder bs iii , pgk / 47 f1731400 / f1721500 front wheel cap packing caf1mm, bs iii , pgk / 65 ia 203036 rear axle packing eicher midi 1mm caf , pgk / 66 f1762900 rear axle packing leyland midi1mmcaf , 2525 0114 6301 gasket push for chamber cover bs iv , 2525 1411 0136 assy gasket ( exhaust manifold ) bs iv , 2525 1411 0135 assy gasket exhaust manifold bs iv , 2786 1499 5301 gasket exhaust manifold bs iii 2017 , 3521 188 0780 gasket oil cooler bs iv , 2786 0999 9962 gasket filter head bs iv / iii / 2017 / , 2786 1899 9910 gasket lube cooler bs iv / iii / 2017 , 216549205301 gasket exhaust system , 276349205301 gasket exhaust pipe flange bs iii / iv , pgk / 78 fs3091dsxna head gasket...

North Western Railway - Rajasthan

31122779 supply of flange welded joint (for 20 mm pipe )flange welded joint (for 20 mm pipe ),flange welded joint (for 20 mm pipe ) sk 85187 alt 1 item no. 1 to 7...

Public Health Engineering Department - Rajasthan

30756089 nit14 conversion of scheme boodh block gangrar :conversion of p&t scheme to piped scheme boodh block gangrar district chittorgarh sl. no. item description 1 constuction of open well 4.0 m dia and 20.00 m deep at boodh 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in lead of 50 mtr. all kinds of soil. 3 from0 m to 1.50 m bgl 4 earth work in excavation in foundation trenches or drains including dressing of sides and ramnming of bottoms lift up to 1.5 mtr including traking out the excavated soil and depositing and refilling of jhiri with watering and ramming and deposals of surplus excavted soil as directed with a lead in a 50 mtr including stacking of useful material if available. 5 ordinary rock 6 from 0.00 m to 4.50 m bgl 7 hard rock (requiring blasting) usefulmaterial 30 % 8 from 0.00 m to 6.00 m bgl 9 from 6.00 m to 25.00 m bgl 10 add extra over item no 2.39.2 4 for every additional; lift of 1.5 m or part thereof: in ordinary rock and hard rock. 11 in ordinary rock and hard rock 12 from 1.50 m to 3.00 m bgl 13 from 3.00m to 4.50 m bgl 14 from 4.50 m to 6.00 m bgl 15 from 6.00 m to 7.50 m bgl 16 from 7.50 m to 9.00 m bgl 17 from 9.00 m to 10.50 m bgl 18 from 10.50 m to 12.00 m bgl 19 from 12.00 m to 13.50 m bgl 20 from 13.50 m to 15.00 m bgl 21 from 15.00 m to 16.50 m bgl 22 from 16.50 m to 18.00 m bgl 23 from 18.00 m to 19.50 m bgl 24 from 19.50 m to 20.00 m bgl 25 add extra over item no 2.39 for excavation in saturated soil where pumping or bailing out of water is required including shorting strutting where required and dewatering. (respective applicable rates) 26 from 6.00 m to 7.50 m bgl 27 from 7.50 m to 9.00 m bgl 28 from 9.00 m to 10.50 m bgl 29 from 10.50 m to 12.00 m bgl 30 from 12.00 m to 13.50 m bgl 31 from 13.50 m to 15.00 m bgl 32 from 15.00 m to 16.50 m bgl 33 from 16.50 m to 18.00 m bgl 34 from 18.00 m to 19.50 m bgl 35 from 19.50 m to 20.00 m bgl 36 centering & shuttering with ply wood or steel sheets including strutting , propping, barcing both ways with wooden members and removal of form work up to floor three level for: walls (any thickness) including attached pilasters, buttresses, plinth and string course. add extra for shuttering in circular work in plan up to dia 10 m over item no 4.7.1 37 providing and fabricating reinforcement for rcc work including straightening, cutting, bending, placing in position in binding (including cost of binding wire) all complete up to floor three level 38 thermo mechanically treated bars (conforming to relevant is:1786.) 39 providing and laying in position specified grade of cement concrete for rcc structure elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement ; 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcement for : 40 walls (any thickness) including attached pilasters buttresses, plinth and string courses fillets columns pillars pears abutments posts struts etc. 41 m20 grade nominal mix (with graded stone aggregate 20mm nominal size) 42 structural steel work in single section fixed with connecting plate includingcutting hoisting fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5 mtr. height 43 in flates, tees, angles & channals 44 in r.s. joists 45 estimate for construction of tube well 46 construction of tube well up to 100 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, (if required) excluding cost of casing pipes, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 (both amended upto date) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe. 47 nominal bore 200 mm dia. 48 add 15% extra on above item for drilling depth beyond 100 mtr, if depth of tube well is more than 100 mtr. 49 supply of erw m.s. black casing pipe isi marked (is: 4270/2001) or amended up to dateoffollowing sizes 50 200 mm dia nb (thickness of pipe 5.4mm & mass of tube 28.46 kg/m) 51 estimate for storage facilities 52 construction and commissioning of rcc intze type over head service reservoir of following capacity and staging as per the scope of work and technical specifications, consisting of the following main activities: 53 a) topographic survey, preparation of site contour plan, conducting sbc testand its approval from departmentbefore construction. submission and approval of concrete mix design and water quality test report for water to be used in construction. b) excavation in all types of soil, pcc below foundation, all rcc work, plinth protection all around the structure including all material, labour, shuttering, scaffolding etc.c) ohsr shall be provided with adequate plinth protection all around the structure in a width starting from edge of structure at gl and extending at least up to 1.0m beyond the edge of outer most projection of ohsr.the plinth protection shall consist of 150mm thick pcc in m 15 grade concrete laid over 150mm thick layer of compacted soil.d) providing and applying two coats of food grade epoxy paint on the inside surface on the top dome, edge beam and 600 mm height of the vertical wall.e)conducting successfully hydro test and water tightness test as per i.s. code.f) providing and applying three coats of anti carbonation paint on the top surface of the top dome.g) providing and applying three coats of cement based paint on the external surface of the container, balcony, cone wall, columns & beams etc..h) providing and fixing ss 304 ventilator, ss 304 manhole frame and cover and ss 304 ladder from top dome/slab to bottom dome/slab inside container. i) providing and fixing of ms section ladder from the last landing to balcony having railing all around it and ms ladder with safety cage from balcony to top dome/slab.j) providing and fixing water level indicator (float type). 54 rates for rcc ohsr,sbc 10 t/sqm, seismic zone ii & staging 18 m 55 200 kl capacity 56 construction of rcc (flat slab type) clear water reservoir of following capacity as per the scope of work and technical specification, consisting of the following main activities: 57 a) topographic survey, preparation of site contour plan, conducting sbc testand its approval from departmentbefore construction. submission and approval of concrete mix design and water quality test report for water to be used in construction. b) excavation in all types of soil, pcc below foundation & all rcc work including all labour and material charges including providing and fixing of accessories such as ss ladder, ss manhole frame and covers, water level indicator (float type), ss ventilator with ss screen, float valve, puddle collars, g.i. pipe railing around walk way, top dome/slab, staircase.c) cwr shall be provided with adequate plinth protection all around the structure in a width starting from edge of structure at gl and extending at least up to 1.0m beyond the vertical wall of cwr. the plinth protection shall consist of 150mm thick pcc in m 15 concrete over 150mm thick compacted soil fill.d) providing and applying two coats of food grade epoxy paint on the inside surface of the roof slab, and 600 mm height of the vertical wall.e) successful hydro test and water tightness test as per i.s. code.f) providing and applying three coats of anti carbonation paint on the roof slab.g) providing and applying three coats of cement based paint on the remaining external surface area of the structure. 58 h) providing and fixing ss 304 ventilator, ss 304 manhole frame and cover and ss 304 ladder from roof slab to bottom slab, inside container. providing and fixing water level indicator (float type).i) providing and fixing ms ladder from ground to top slab. j) all ms parts to be painted with two coats of the enamelled paint over the primer coat of red oxide.k) providing and fixing of 150mm wide water bar for the construction joints in the container.l) providing and fixing ci/di puddle collars the vertical wall for connecting inlet, outlet, overflow and washout pipes of the reservoir.m) inlet, outlet, overflow, washout pipes and valves are not included in this work, provision for the same shall be taken separately. 59 rates for rcc partially underground type clear water reservoir sbc 7 t/sqm, seismic zone 2,3 & 4 60 75 kl capacity 61 providing and fixing double flanged isi marked diclass k 9 pipes as per is:8329 2000 (amended up to date), asvertical pipes for rcc reservoirs including specials required such as duck foot bend, bend, tee etc. providing clamps at every 3 mtr,jointing materials such as nuts, bolt, rubber packing, hydraulic testingetc. complete in all respect up to and from valve chamber as per direction of eic, technical specification and scope of work. 62 100 mm 63 150 mm 64 200 mm 65 construction of rcc valve chamber 66 estimate for rising system 67 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and disposal of surplus excavated soil asdirected within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 68 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and stacking serviceable material formeasurements and disposal of unserviceable material as directed, with in a lead of 50mtr. including all safety provisions required .: 69 ordinary rock 70 hard rock (requiring blasting) 71 hard rock(blasting prohibited) 72 dismantling of cement concrete pavement for pipe lineand chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shallbe made for trench width more than specified, re handling of material/earth to complete the tasks as per technical specification and scope of work. 73 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 74 m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 75 providing, lowering, laying in trenches, aligning, fixing in position and jointingductileiron(di)isi markedk 7grades&spipesas per is:8329 2000 (amendeduptodate),withinternalcementmortar lining suitable for potablewater with rubber ring (epdm)joints as per is: 5382 1985 including all taxes (central and local), transportation and freight charges, inspection charges, loading/ unloading charges,including cost of labour and material, specials (tee, bend etc.) satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge. (excluding earth work) note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 76 100 mm 77 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesof approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem ss 304 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date), all exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to is:5660 and two coats of black japan paint conforming totype b of is 341or paint conforming to is9862 or is2932( non toxic suitable for drinking water) applied inside and outside, flanges drilled as per is 1538.nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steel.insersion rubber of black epdm 6mm thick . suitablesupport structure as per directions of eic. sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge.note: rates are exclusive of tail piece/ dismantling joints and earth work. 78 manually operated ci sluice valve of class pn 1.0 79 100 mm hw 80 dismantling of cement concrete pavement for pipe lineand chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shallbe made for trench width more than specified, re handling of material/earth to complete the tasks as per technical specification and scope of work. 81 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 82 m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 83 construction of rcc valve chamber 84 estimate for distribution system 85 providing, lowering, laying in trenches, aligning, fixing in position and jointingductileiron(di)isi markedk 7grades&spipesas per is:8329 2000 (amendeduptodate),withinternalcementmortar lining suitable for potablewater with rubber ring (epdm)joints as per is: 5382 1985 including all taxes (central and local), transportation and freight charges, inspection charges, loading/ unloading charges,including cost of labour and material, specials (tee, bend etc.) satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge. (excluding earth work) note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 86 80 mm 87 100 mm 88 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 (amended upto date)with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (tee, bend etc.), satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. (excluding earth work) .note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately.supply may be in coil or straight length in 6 m/12 m. 89 hdpe pe 80pn 6 90 75 mm dia 91 90 mm dia 92 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesof approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem ss 304 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date), all exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to is:5660 and two coats of black japan paint conforming totype b of is 341or paint conforming to is9862 or is2932( non toxic suitable for drinking water) applied inside and outside, flanges drilled as per is 1538.nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steel.insersion rubber of black epdm 6mm thick . suitablesupport structure as per directions of eic. sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge.note: rates are exclusive of tail piece/ dismantling joints and earth work. 93 manually operated ci sluice valve of class pn 1.0 94 80 mm hw 95 100 mm hw 96 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and disposal of surplus excavated soil asdirected within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 97 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and stacking serviceable material formeasurements and disposal of unserviceable material as directed, with in a lead of 50mtr. including all safety provisions required .: 98 ordinary rock 99 hard rock (requiring blasting) 100 hard rock(blasting prohibited) 101 dismantling of cement concrete pavement for pipe lineand chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shallbe made for trench width more than specified, re handling of material/earth to complete the tasks as per technical specification and scope of work. 102 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 103 m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 104 estimate for pump house & pumping machinary 105 providing, installation, testing and commissioning of centrifugal monoblock pump set conforming to is 9079 operating at sync. speed 2900 rpm with requisite moc impeller, priming funnel, cock, suitable flanges at suction and delivery side. pump shall have common shaft for pump and motor. motor shall be suitable for working on 415 v ± 10%, 3 ph, 50 hz a.c. supply. motor shall be tefc type and pump set shall be suitable for working at various discharge and head requirements as per scope of work. pump shall be erected onc.c. foundation / cross channels / rsj frame block with suitable foundation bolts grouted in c.c. foundation block etc. complete in all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions of one of the makes approved by technical committee. 106 centrifugal monoblock pump set (single stage) 107 5 hp 108 providing, installation, testing and commissioning of submersible monoblock pump set conforming to is 8034 and motor conforming to is 9283, with water proof winding. pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415 v ± 10%, 3 ph, 50 hz ac and with water lubricated bearing to accept entire hydraulic thrust. supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. the pump set shall be suitable for direct coupling, with suitable suction strainer. pump should have suitable discharge out let as per manufacturers design. antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. completein all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions of one of the makes approved by technical committee. 109 5.0 hp 110 providing, lowering, aligning, fixing in position in pipe line, ci double flanged swing type non return valves (nrv)of approved make of following pressure rating & dia complete, confirming to is: 5312 (part 1)/ 2004 (amendedup to date) and of following specifications: body, cover & disc of grey cast iron of is:210/ fg200. face to face dimensions as per is 5312 (part 1):2004 , flanges drilled as per is:1538. all exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to is:5660and two coats of black japan paints conforming totype b of is 341or paint conforming to is9862 or is2932( non toxic suitable for drinking water) applied inside and outside. body seat ring of ss/cs door face ring epdm/ neoprene (food grade quality) ,shaft of htb1/ ss aisi 410, hinge malleable cast iron / ss aisi 316/410 ,bonnet gasket epdm, bush leaded tin bronze/ ptet, gasketepdm/nbr,nut bolt as per is:1363 and is: 1367 (galvanised steel) ,insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic including jointing & jointing material, labour, testing and commissioning along with pipeline as per technical specification & as per direction of engineer in charge.note: rates are exclusive of tail piece/ dismantling joints and earth work. 111 class pn 1.0 112 100 mm dia 113 providing, lowering, aligning, fixing in position in pipe line at work site, di d/f resilient seated (soft seated) sluice valves (gate valves) , vacuum tight(bubble tight), straight and pocket less body passage of approved make of following class & dia complete confirming to bs en 1171/ awwa c 509 and of following specifications: body & bonnet of ductile cast iron of grade ggg40/ggg50 as per din 1693 or gr sg 400/12 as per is 1865 or equivalent grade as per is :3896 part2 1985 and subsequent revisions, wedge of same material as body & shall vulcanisedrubber lined with epdm (food grade quality) and seals of nbr face to face dimensions as per bs 5163 89/ is 14846/2000 (amended up to date) /din 3202 f4, stem/ spindle of ss (aisi 316 or equivalent) electrostatic epoxy powder(ep p)/ fusion bond epoxy ( non toxic suitable for drinking water) coated with minimum thickness of 250 microns inside and outside, drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367(galvanised steel) insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic, sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. 114 manually operated resilient seated sluice valves of class pn 1.0/1.6 115 100 mm dia 116 star delta starter 12.5 hp (1w+ 1s): i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3)and o/g mcb 40a ,tp, 10 ka, c curve (2), power cont 18a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase priventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 5kvar (2), s/d timer(2) 117 supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg.including all jointing material as per specification with safety cover. 118 estimate fortube well pumpset 119 supply & installation of 3 phase isi marked submersible motor pump set offive star rating by bee and as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 120 7.5 kw (10 hp) & head up to 120 mtr. 121 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay,ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom).all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 122 above 5 hp and up to 10 hp 123 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 124 3 core 4.0 sq.mm 125 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 126 providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 127 50 mm dia 128 providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064/1 or amended upto date of approved make including cost of all material andlabouras per specifications with gi box (sheet 16 swg) suitable with locking arrangement of following dia. 129 50 mm dia 130 estimate for pump house & boundary wall 131 construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect. 132 construction of boundary wall of brick/ stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. 133 providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamal paints. 134 construction of rain water harvesting structures at various govt building. 135 construction of tube well up to 100 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, (if required) excluding cost of casing pipes, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 (both amended upto date) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a through out bore as per nominal dia of casing pipe. (phed/2.4) 136 nominal bore 200 mm dia. 137 supply of erw m.s. black casing pipe isi marked (is: 4270/2001) or amended up to dateoffollowing sizes (phed/2.11.2) 138 200 mm dia nb (thickness of pipe 5.4mm & mass of tube 28.46 kg/m) 139 labour charges for making slots on blank pipes made of erw ms black pipe of following sizes, the slotting should be as per is:8110 2000 or as amended up to date. (phed/2.12.3) 140 200 mm dia nominal bore. 141 supply of bore well cover to accommodate 200 mm ms pipe made of ms flat & ms sheet as per drawings (pwd2019 4.8.4) 142 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 143 add extra for trenches for every additional lift over item no 5.0 144 above 1.5 mtr and up to 3.0 mtr. 145 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and stacking serviceable material for measurements and disposal of unserviceable material as directed, with in a lead of 50 mtr. including all safety provisions required. 146 ordinary rock 147 hard rock (blasting prohibited) 148 add extra for trenches for every additional lift over item no 6.0 149 above 1.5 mtr and up to 3.0 mtr. 150 providing and laying in position cement concrete including curing compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level using crusher broken aggregate 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm size) (pwd2019 3.2.7) 151 providing and laying in position specified grade of reinforcement cement concrete all rcc structural elements upto plinth levelincluding curing compaction finishing with rendering in cement sand mortar 1:3 ( 1 cement : 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcementm20 grade nominal mix (with graded stone aggregate 20mm nominal size) (pwd2019 4.1.2) 152 centering & shuttering with ply wood or steel sheets including strutting , propping, barcing both ways with wooden members and removal of form work up to floor three level for: suspended floors, roofs, landings staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks sills, chhajjas, lintel, beams etc. (pwd2019 4.7.2) 153 providing and fabricating reinforcement for rcc work including straightening, cutting, bending, placing in position in binding (including cost of binding wire ) all complete up to floor three level cold twisted deformed bars (is:1786) (pwd2019 4.12.2) 154 brick masonry in foundation & plinth, using bricks of class destination 75 in cement mortar 1:6 (1cement: 6 coarse sand)(pwd2019 5.1.7) 155 plaster on new surface on wall in cement sand mortar 1:3 including raking of joints etc. complete fine finish: 20mm thick (pwd2019 12.7.2) 156 steel work in single section fixed with connecting plate including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5 mtr height. in flates, tees, angles & channals. (pwd2019 9.2.1) 157 supply & lying river gravels of following sizes in recharge shaft filter pit after screening & washing from kachha shift without deduction of voids. (pwd2019 4.28) 158 size 9 to 12 mm 159 size 3 to 5 mm 160 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110mm dia (pwd2019 3.19.3) 161 providing, laying & jointing of 110 mm dia hdpe pipe class pe 80 pn 6 162 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: (pwd2019 3.20) 163 bend 87.5, 110 mm dia 164 pipe clip 110 mm c18 165 door tee 110 mm 166 finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade inclg. all scaffolding new works ( three or more coats). (pwd2019 12.53.1) 167 making functional house tap connections ( fhtcs ). 168 providing household tap connectionas per technical specification andapproved drawing and as per relevant is code (amended up to date) from hdpe pipe line up to consumer meter/premises by using electro fusion saddle piece (complete job).this job includes digging out suitable size of pits and trench for laying service line in all kinds of soil; depositing and refilling of pit & jhiri with watering & ramming /compacting in layers and disposal of surplus excavated soil as directed with in a lead of 100 meter ; providing & fixing of all fitting duly approved in accordance withspecification for potable water including electrofusion saddle piece, gunmetal ferrule 4.0 mm , gm full way valve (is:778 mark) or wheel valve and specials, below ground level 20 mm nominal dia mdpe pipe pe80 pn 16 as per iso 4427 / 20 mm nominaldia ppr c (three layered) pipepn16 sdr 7.4 (is:15801:2008) (isi mark) for and above ground level using 20 mm dia ppr c pipe with standard ppr fittings/ 15 mm dia gi pipes with fittings in the premises for fixing a tap / meterbox (excluding) ,including accessories with flushing, cleaning, disinfecting and testing of pipe line complete required for making of service connection complete in all respect including labour charges . the service line should be laid at least 45 cm below ground level.note: road cut and restoration is not part of this item and paid seperately. 169 for connection with 20 mm dia mdpe/ppr c pipe length up to 05 mtr. 170 p& f bib cock (is : 8931 mark), superior quality of approved make , brss 400 gm, 15 mm nominal bore. 171 road cutting for house hold service connection in minimum trench width whereever road crossing is required. road cutting of cement concrete,wbm, black top etc. of all thickness shall be doneby using a concrete cutter machine keeping minimum trench width and restoration of the road with cement concrete with pcc m 10 and cc m 30 grade as per specification and direction of engineer in charge.. 172 add extra over item no 1.21 & 1.22 for providing20 mm pe80 pn 16 as per iso 4427 mdpe pipe including excavation, providing, laying & jointing of service line above 5.00 mtr. ...

Public Health Engineering Department - Rajasthan

29333170 work of conversion of p and t wss water supply scheme in piped wss village balda ( v ) , sub division sirohi, district sirohi under jjm nit no. 177 / 2021 22 construction of open well 5.00 mtr dia & 25.00 mtr depth at village balda (v). (ce&tm, rwssmb phed jaipur bsr 18.8.2020 & pwd bsr 2019) 2 (2.39) earth work in excavation over areas (exceding 30cm depth, 1.5 mtr in width and 10 sqm in plan)for construction of open well, lift up to 1.5 mtr. including taking out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 meter. 3 (2.39.1) all kind of soil 4 (2.39.2) ordinary rock 5 (2.39.4) hard rock (blasting prohibited) useful material 30% 6 (2.39.5) recovery for useful material from hard rock 7 (2.4) add extra over item no. 2.39.1 for every additional lift of 1.5 mtr. or part thereof : in all kind of soils. 8 s. no./ from (m)/ to (m)/ lift 9 1/ 1.5/ 3/ 1st 10 2/ 3/ 4/ 2nd 11 (2.41) add extra over item no. 2.39.2 4 for every additional lift of 1.5 mtr. or part thereof : in ordinary rock and hard rock. 12 s.no./ from (m)/ to (m) 13 1/4.0/5.5/3rd 14 2/5.5/7/4th 15 3/7.0/8.5/5th 16 4/8.5/10.0/6th 17 hard rock 18 1/ 10/ 11.5/ 7th 19 2/ 11.5/ 13/ 8th 20 3/ 13/ 14.5/ 9th 21 4/ 14.5/ 16/ 10th 22 5/ 16/ 17.5/ 11th 23 6/ 17.5/ 19/ 12th 24 7/ 19/ 20.5/ 13th 25 8/ 20.5/ 22/ 14th 26 9/ 22/ 23.5/ 15th 27 10/ 23.5/ 25/ 16th 28 (2.42) add 20% extra over item no. 2.39 for excavation in saturated soil where pumping or baling out of water is required, including shoring strutting where required and dewatering. 29 (4.2) reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement:3 coarse sand) and making good the joints excluding cost of centering shuttering and reinforcement is 456 2000: 30 (4.2.3) 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size). 31 (4.12.1) centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways with wooden members andremoval of formwork for superstructure up to 4.5 mtr aboveplinth,for:walls (any thickness) including attached pilasters, buttresses, plinth and string course. 32 (4.13.3) providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level.hot rolled deformed bars (is : 1139) 33 (9.1) structural steel work in single section fixed without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level up to 4.5 mtr. height in r.s. joist flats, tees, angles and channels. 34 (2.43) labourchargesfor horizontalboring100 mm diain openwell in rocky stratawith all types of rock cutting & drilling tools etc. including all t&p required for jobincluding dewatering arrangement. 35 (2.24) providing & lowering in tube well isi marked gi pipe medium duty (“b class), steel tube as per is:1239 or amended up to date and zinc coating as per is 4736, threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 36 (2.24.3) 65 mm dia 37 flushing of existing tube well (ce&tm, rwssmb phed jaipur bsr 18.08.2020) 38 (2.7) deepening of existing tube well by dth system beyond existing depth upto 100 mtr. and above in all type of ...

Panchayat Raj Department - Rajasthan

29165888 material supply to gp rodwal for boring work three phase boring conection majra ke pass garelu conection hetu pipeline bheemsinghpura , construction of tube well from ground level and upto 100 mtr. depth and above to accommodate housing and assembly pipe in all type of alluvium strata, unconsolidated formation such as pebbles, boulders etc. by percussion / rotary drilling method as per is:2800 ( part 1 & 2 ) 1979 as amended up to date.the work will include cost of lowering of housing, strainer assembly pipes, with supply and wrapping of coir rope, wherever necessaryand development of tube well as per is specification using suitableair compressor but will not include cost of casing & strainer pipe. work will be completed after obtaining sand free water. nominal bore 200 mm dia , construction of tube well after completion of item no. 2.1 & upto 100 mtr.depth and abovein all type of rocks by dth system as per is : 2800 ( part i & ii ) 1979 as amended up to date. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal bore of casing pipe. nominal bore 200 mm dia , add 15% extra on above item for drilling depth beyond 150 mtr, if depth of tube well is more than 150 mtr. , supply of erw m.s. black casing pipe isi marked ( is: 4270 / 2001 ) or amended up to dateoffollowing sizes 200 mm dia nb ( thickness of pipe 5.4mm & mass of tube 28.46 kg / m ) , supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both end in 80mm sizes passing through a hole in the centre of ms sheet. a 25mm socket with end plug shall also be welded over top plate ( as per drawillg enclosed ) . a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall tie provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug : 200mm dia , supply & installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per js: 8034 2011 ( pump ) and is 9283 2013 ( motor ) or amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. ( including 1 no stanby p / set ) : 15 kw ( 20 hp ) & head above 120 mtr. , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 50 mm dia , supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventor, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 guage m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each legs length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form.the sizeof cc plateform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440volt ac supply. above15 hp , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 25.0 sq.mm, 3.5 core , supply & fixing of isi marked three core pvc flat submersible cable as per is 694: 1990 or amended up to date and conductor as per class 5 of is8 130: 1980 includ ing making connection etc. 3 core 4.0 sq mm , electric connection , part b ( pipe line work ) uhao [ kkbz ij uky esa 1 5ehvj xgjkbz rd fevvh dh [ kqnkbz djuk ry dks dqvuk ikuh mkyuk cxy dks lokjukk [ kqnh fevvh dks ckgj fudkyuk uhao hkjus ds ckn [ kkyh lfkkuks dks iqu% fevvh ls hkjuk rfkk cuh gqbz fevvh dks yxkrkj 50 eh dh nwjh rd fulrkj.k djuk lk [ r , providing & lowering isi marked hdpe pipe as per is 4984: 1995 or amended up to date in pe 80gradeand class pn 10, 75 mmdia phed bsr 2020 , vale tee etcas per market rate...

Public Health Engineering Department - Rajasthan

28890260 commissioning of source under south dn barmer 1 providing & laying isi marked gi pipe ·a .. class as per is: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect 2 supply & installation of 3 phase isi marked submersible motor pump set of five star rating by bee and as per js: 8034 2011 ( pump ) and is 9283 2013 ( motor ) or amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnectionup to water mains, complete in all respect. up to 5.5 kw ( 7.5 hp ) & head up to 120 mtr. 3 up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. 4 7.5 kw ( 1o hp ) & head up to 120 mtr. 5 7.5 kw ( 1o hp ) & head above 120 mtr. 6 9.3 kw ( 12.5 hp ) & head up to 120 mtr. 7 9.3 kw ( 12.5 hp ) & head above 120 mtr. 8 11 kw ( 15 hp ) & head up to 120 mtr. 9 11 kw ( is hp ) & head above 120 mtr. 10 13 kw ( 17.5 hp ) & head up to 120 rntr. 11 13 kw ( 17.5 hp ) & head above 120 mtr. 12 15 kw ( 20 hp ) and above, head up to 120 mtr. 13 15 kw ( 20 hp ) and above, head above 120 mtr. 14 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventor, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 guage m.s. sheet with powder coating. panel should be of minimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each legs length 18 and double door including in built locking system. the legs should be embedded in m 15 cement concrete plat form.the size of cc plateform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440volt ac supply. above 5 hp and up to 10 hp 15 above 10 hp and up to 15 hp 16 above 15 hp 17 supply & fixing of isi marked three core pvc flat submersible cable as per is 694: 1990 or amended up to date and conductor as per class 5 of is 8 130: 1980 includ ing making connection etc. 3 core 4.0 mm2 18 3 core 6.0 mm2 19 3 core 10.0 mm2 20 3 core 16.0 mm2 21 s&f xlpe insulated / pvc sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved make in ground as per is:1225 including excavation of 30cmx 75cm size trench 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction ofearth, making necessary connection, testing etc. as required of size. 10 sqmm 4 core 22 16 sqmm 4 core 23 25 sqmm 4 core 24 35 sqmm 4 core 25 s&f m s clamp set of 50x6mm flat iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 26 plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600 mmx6.0mm by embodying in 3 to 4 mtr. below the ground level with 20mm dia. gi b class watering pipe including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and c.c. finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x300mm complete wih alternate layers of salt and coke / charcoal, testing of earth resistance as required. 27 supply & fixing tube well cover of ms sheet 8mm thick at top & 5mm thick i oomm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both end in 80mm sizes passing through a hole in the centre of ms sheet. a 25mm socket with end plug shall also be welded over top plate ( as perdrawillg enclosed ) . a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall tie provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. 200mm 28 250mm 29 providing & lowering in tubewell isl marked gi pipe b class as per is: 1239 or amended up to date threaded and double flanged ( welded ) on both ends and two number 25x3mm flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 50 mm dia 30 65mm dia 31 80mm dia 32 providing & lowering in tubewell lsi marked hope pipe as per is 4984: 1995 or amended upto date in pe 80 grade and class pn 10 offollowing dia. including hope / gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. 50 mm dia 33 63 mm dia 34 75 mm dia 35 90 mm dia 36 providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 406411 or amended upto date of approved make including cost of all material and labour as per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. 50mm dia 37 65mm dia 38 80mm dia 39 providing & fixing pump safety cage as per specifications or as directed by engineer in charge 40 providing & fixing of double flanged, cl body, isi marked nr v of approved make of following sizes 65mm dia 41 80mm dia 42 supplying & installing i 00 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to i 0 kg. including all jointing material as per specification and safety cover. 43 structural steel work welded in built up sections, trusses and framed work exclusively for open wells including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5mtr. height in r.s. joints flats, tees, angles and channels....

Panchayat Raj Department - Rajasthan

28709166 tender for hundpump tubewell work , construction of tube well from ground level & up to 100 mtr depth to accommodate housing and assembly pipe of following sizes in all type of alluvium strataunconsolidated formation such as pebbles, boulders etc. by percussion / rotary drilling method as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications, with gravel as per is:4097 1967 and its packing as per is: 2800 ( part i & ii ) 1979 as amended up to date ( the work includes the cost of gravel & its primary packing and packing during development, lowering of housing & strainer assembly pipes with supply and wrapping of coir rope, wherever necessary for arresting fine sand particles and development work, but excluding the cost of housing and strainer pipe assembly ) . the work would be completed after obtaining sand free water. , nominal bore 150 mm dia. , nominal bore 200 mm dia. , nominal bore 250 mm dia. , add 15% extra on depth more than 100 mtr for drilling beyond 100 mtr depth from ground level. , construction of tube well from ground level and upto 100 mtr. depthto accommodate housing and assembly pipe in all type of alluvium strata, unconsolidated formation such as pebbles, boulders etc. by percussion / rotary drilling methodas per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications for removal of overburden. the work includes the cost oflowering of casing pipe, but excludes the cost of casingpipe. , nominal bore 200 mm dia. , nominal bore 250 mm dia. , add 15% extra on depth more than 100 mtr for drilling beyond 100 mtr depth from ground level. , construction of tube well after completion of drilling by rotary method & upto 150 mtr. depthin all type of rocks by dth systemas per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the workshall be deemed completed only after obtaining sand free water. the bore well should have a throughout nominal size bore beyond casing pipe. , nominal bore 150 mm dia. , nominal bore 200 mm dia. , add 15% extra on depth more than 150 mtr for drilling beyond 150 mtr depth from ground level. , construction of tube well up to 150 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soil & over burden including lowering of casing pipe, ( if required ) excluding cost of casing pipe, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a through out bore as per nominal dia of casing pipe. , nominal bore 150 mm dia. , nominal bore 200 mm dia. , add 15% extra on depth more than 150 mtr for drilling beyond 150 mtr depth. , construction of tube well from ground level and upto 100 mtr. depth and above of following sizes in all types of soils in alluvium strata, unconsolidated formation such as pebbles, boulders etc. by bailing method and without gravel packing as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the work includes formation of cavity at bottom by development with appropriate air compressor or bailer pumping and also lowering of casing pipe but excluding cost of the casing pipe.the tube well should have a throughout bore as per nominal dia of casing pipe.the work would be completed after obtaining sand free water. , nominal bore 125 mm dia. , nominal bore 150 mm dia. , nominal bore 200 mm dia. , construction of tube well from ground level and up to 100 mtr depth and above to accommodate housing assembly pipe in all type of unconsolidated formation such as pebbles, boulders, collapsible formation etc. by odex drilling method as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the work will include lowering of housingand strainer pipe assembly and casing shoe incuding cost of casing shoe, but excluding cost of the casing pipe. the work would be completed afterobtaining sand free water. , nominal bore 125 mm dia. , nominal bore 150 mm dia. , nominal bore 200 mm dia. , deepening of existing tube well by dth system beyond existing depth upto 100 mtr. and above in all type of rocks including flushing of tube well and obtaining sand free water. , nominal bore 150 mm dia. , nominal bore 200 mm dia. , testing verticality of tube well by plumbing system and yield test and draw down test by pumping system as per is : 2800 ( part – ii ) – 1979 or as amended up to date. , supplying & packingp gravel suitable for slot size / mesh size as suggested in is 2800 ( part 1 ) 1991 or as amended up to date. , development of tube well as per is: 11189 1985 and is: 2800 ( part i ) 1991 ( both amended up to date ) using suitable compressor to give sand free water for required yield of the gravel packed tube well. , supply of erw m.s. black casing pipe isi marked ( is: 4270 / 2001 ) or amended up to date offollowing sizes , 150 mm dia nb ( thickness of pipe 5.0 mm & mass of tube 20.13 kg / m ) , 200 mm dia nb ( thickness of pipe 5.4mm & mass of tube 28.46 kg / m ) , 250 mm dia nb ( thicknee of pipe 7.1 mm & mass of tube 46.57 kg / m ) , labour charges for making slots on blank pipes made of erw ms black pipe of following sizes, the slotting should be as per is:8110 1985 or as amended up to date. , 125 mm dia nominal bore.of 4.8 mm thickness , 150 mm dia nominal bore.of 4.8 mm thickness , 200 mm dia nominal bore.of 5.4 mm thickness , 250 mm dia nominal bore.of 7.1 mm thickness , providing & laying isi marked gi pipe light duty ( “a” class ) as peris: 1239for casing pipe for submersible cable external work 40 mm dia complete in all respect. , supply & installation of single phase isi marked submersible motor pump set of five star rating by bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , up to 2.0 kw , above 2.0 kw , supply & installation of 3 phase isi marked submersible motor pump set offive star rating by bee and as per is: 8034 2018 ( pump ) and is 9283 2013 ( motor ) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well / dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. , up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. , up to 5.5 kw ( 7.5 hp ) & head above 120 mtr. , 7.5 kw ( 10 hp ) & head up to 120 mtr. , 7.5 kw ( 10 hp ) & head above 120 mtr. , 9.3 kw ( 12.5 hp ) & head up to 120 mtr. , 9.3kw ( 12.5 hp ) & head above 120 mtr. , 11 kw ( 15 hp ) & head up to 120 mtr. , 11 kw ( 15 hp ) & head above 120 mtr. , 13 kw ( 17.5 hp ) & head up to 120 mtr. , 13 kw ( 17.5 hp ) & head above 120 mtr. , 15 kw ( 20 hp ) and above, head up to 120 mtr. , 15 kw ( 20 hp ) and above, head above 120 mtr. , supply and fixing of electric feeder panel ( having projected canopy ) for submersible pump set single phase upto 3 hp, comprising of dol starter, mcb, indicating light, ammeter, volt meter, connection plate, condensers of approved make and the panel enclosure should be made out from 18 guage m.s. sheet with powder coating. panel size height 600 mm, width 500 mm and depth 250 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete platform.the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the operation of panel should be suitable for240 volt ac supply. , supply and fixing of electric control feeder panel comprising of suitable rating mccb, dol starter, overload relay, ampere meter, volt meter, phase preventer, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) . all these equipments shall be housed by panel box made out from 18 guage m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 300mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete platform.the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level.the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for440 volt ac supply. , up to 5.00 hp , supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay, ampere meter with cts, volt meter, phase preventor, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom ) .all these equipments shall be housed by panel box made out from 18 guage m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm ) duly bolted / screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form.the size of cc plateform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for440 volt ac supply. , above 5 hp and up to 10 hp , above 10 hp and up to 15 hp , above 15 hp , supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. , 3 core 4.0 sq.mm , 3 core 6.0 sq.mm , 3 core 10.0 sq.mm , 3 core 16.0 sq.mm , supply & fixing xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i / 1554 1 approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. , 10 sq.mm, 4 core , 16 sq.mm, 4 core , 25 sq.mm, 3.5 core , 35.0 sq.mm, 3.5 core , plate earthing as per is:3043 with g.i. earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20 mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer , nipple, wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover, c.i. frame of size 300mm x 300mm complete with alternate layers of salt and coke / charcoal, testing of earth resistance as required. , supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. , supply & fixing tube well coverof ms sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with gi nipple 45cm long & two gi flanges at both ends in 80mm sizes passing through a hole in the centre of ms sheet. a 25 mm socket with end plug shall also be welded over top plate. a gi nipple having outside thread of size 1 / 2 ( for installation pressure gauge ) shall be provided & welded with 80mm gi nipple near top plate nipple shall be provided with end plug. , 125 mm dia , 150 mm dia , 200 mm dia , 250 mm dia , providing & lowering in tubewell isi marked gi pipe “b ( medium ) class as per is:1239 part i 2004 or amended up to date, threaded and double flanged ( welded ) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. , 32 mm dia , 50 mm dia , 65 mm dia , 80 mm dia , providing & lowering in tubewell isi marked hdpe pipe as per is 4984:1995 or amended upto date in pe 80 grade and class pn 10 of following dia. including hdpe / gi fittings and pvc rope confirming to is 5175:1992 or amended upto date, along with clamping of submersible cable etc. complete in all respect. , 40 mm dia , 50 mm dia , 63 mm dia , 75 mm dia , 90 mm dia , providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064 / 1 or amended upto date of approved make including cost of all material andlabouras per specifications with gi box ( sheet 16 swg ) suitable with locking arrangement of following dia. , 50 mm dia , 65 mm dia , 80 mm dia , providing & fixing pump safety cage as per specifications or as directed by engineer in charge. , providing and fixing of isi marked pvc storage tank of following capacityas per is: 12701 1989 ( of approved make ) with cover, 25 mm dia. 1 mtr long gi overflow pipe, 25 cm long 25 mm dia washout gi pipe with plug & socket, including p&f 32 mm dia ball cock ( float valve ) is 1703 marked with rod and pvc ball complete with brass weight 1000 gm, including p&f 15mm dia ci quarter turn heavy duty bib cocks four nos of superior quality and approved make, including interconnections complete job. , 1000 litres capacity , 2000 litres capacity , fabrication & fixing m.s.stand of specified class of angle iron l shaped of 50 mm size with four legs grouted by 300*300*300 mm cc block m 15 in the ground and all legs tied up with each other through same size of angle iron along with cross bars to support the bottom of 1000 ltr. / 2000 ltr. pvc tank complete in all respect. , providing & fixing of double flanged, ci body, isi marked nrv of approved make of following sizes , 65 mm dia , 80 mm dia , proving and fixing 32 mm dia full way valve or wheel valve as per is:778 or amended up to date of approved make, on pump delivery pipe. , supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg.including all jointing material as per specification with safety cover. , construction of bore hole for shallow depth tube well from ground level to required depth for following size for all type of relevant strata by percussion / rotary drilling / hand boring method excluding cost of casing pipe. thebore hole should be as per nominal bore of pvc casing pipe. the work will be complete after obtaining sand free water. , providing and lowering of isi mark pvc u casing and screen pipe as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for tw and dcb with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. , shallow well casing pipe ( cs ) suitable for depth up to 80 mtr. , 150 mm nominal dia ( internal dia ) . , 200 mm nominal dia ( internal dia ) . , 250 mm nominal dia ( internal dia ) . , medium well casing pipe ( cm ) suitable for depth above 80 mtr and up to 250 mtr. , 100 mm nominal dia ( internal dia ) . , 125 mm nominal dia ( internal dia ) . , 150 mm nominal dia ( internal dia ) . , 200 mm nominal dia ( internal dia ) . , 250 mm nominal dia ( internal dia ) . , supply of isi mark ac pressure pipe class 15 manufactured by mazza process as per is:1592 2003 or amended upto date, for casing of tube wellfor following dia nominal bore, with jointing material pvc coupler as per technical specification and direction of engineer in charge. , 125 mm nominal dia , 150 mm nominal dia , 200 mm nominal dia , 250 mm nominal dia , 300 mm nominal dia , making slots of hole size and nos. as directed by eic in ac pressure pipe class 15 as per technical specification for using slotted pipe in tw casing. , construction of tube well from ground level & up to 100 mtr depth to accommodate housing and assembly pipe of following sizes in all type of alluvium strataunconsolidated formation such as pebbles, boulders etc. by percussion / rotary drilling method as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications, with gravel as per is:4097 1967 and its packing as per is: 2800 ( part i & ii ) 1979 as amended up to date ( the work includes the cost of gravel & its primary packing and packing during development, lowering of housing & strainer assembly pipes with supply and wrapping of coir rope, wherever necessary for arresting fine sand particles and development work, but excluding the cost of housing and strainer pipe assembly ) . the work would be completed after obtaining sand free water. , nominal bore 125 mm dia. , add 15% extra on above item for drilling depth beyond 100 mtr, if depth of bore is more than 100 mtr. , construction of tube well up to 100 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all type of soils & over burden including lowering of casing pipes, ( if required ) excluding cost of casing pipes, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe. , nominal bore 125 mm dia. , nominal bore 125 mm dia. , add 15% extra on above item for drilling depth beyond 100 mtr, if depth of bore is more than 100 mtr. , construction of tube well from ground level and upto 100 mtr. depth and above of following sizes in all types of soils in alluvium strata, unconsolidated formation such as pebbles, boulders etc. by bailing method and without gravel packing as per is:2800 part 1: 1991 andis:2800 part ii: 1979 ( both amended upto date ) and technical specifications. the work includes formation of cavity at bottom by development with appropriate air compressor or bailer pumping and also lowering of casing pipe but excluding cost of the casing pipe.the tube well should have a throughout bore as per nominal dia of casing pipe.the work would be completed after obtaining sand free water. , nominal bore 100 mm dia. , nominal bore 125 mm dia. , supply ofm.s. black casing pipe isi marked as per is: 1239 ( part 1: 2004 ) or amended up to date offollowing sizes: , 100 mm dia nb ( thickness of pipe 4.8 mm & mass of tube 16.40 kg / m ) , 125 mm dia nb ( thickness of pipe 4.8 mm & mass of tube 16.40 kg / m ) , providing and lowering of isi mark medium wellpvc u casing and screen pipe ( cm ) as per is : 12818 : 2010 or amended upto date having pipe thickness as per is code suitable for bore well with threading , winding with superior quality of plastic mesh & rope in three layers with end cap complete as per technical specification and direction of engineer in charge. , 100 mm nominal dia ( internal dia ) . , 125 mm nominal dia ( internal dia ) . , labour charges for making slots on blank pipes made of erw ms black pipe isi marked of following sizes, the slotting should be as per is:8110 1985. , 100 mm dia nominal bore , 125 mm dia nominal bore , supply & installation of gi pipe 32 mm medium class “b” with pipe sockets ( heavy duty ) . , supply and installation of isi markeddeep well hand pump standard ( sdwp ) setas per is 15500: 2004 or as amended up to date complete with cylinder & 15 connecting rods. , supply and installation of isi marked india mark ii hand pump set extra deep ( edw ) completewith cylinder and connecting rods. , edwhp + 20 connecting rod. , edwhp + 23 connecting rod + 1 weight. , edwhp + 26 connecting rod + 2 weight. , edwhp + 30 connecting rod + 3 weight. , supply and installation of isi mark connecting rod as per departmental specifications of3 meter length. , installation of deep well hand pump set complete on existing platform as per is 15500: 2004 or as amended up to date. , construction of 185 cm. dia platform as per fig 1.1 typical set up for deepwell hand pump of is 15500: 2004 or amended up to date complete work....