31267710
request for proposal for rate contract for supply, operation and maintenance of tinkering lab request for proposal for rate contract for supply, operation and maintenance of tinkering lab , arduino uno with enclosure and compatible usb cable , arduino nano with enclosure and compatible usb cable , arduino mega with enclosure and compatible usb cable , general purpose solderable board fr2 a grade material (140 x 90 mm) , general purpose solderable board fr2 a grade material (80 x 55 mm) , berg strips (male and female both ) 2.54mm pitch, 40 pin single row,breakable pin , solderless 400 pin breadboard , solderless 800 pin breadboard , self adhesive proto shield , 16*2 lcd display, dot matrix lcd display , 16 characters * 2 lines , usb cable set usb a to usb micro b, (12 inch or more) 5 cable per set , digital multimeter (200mv 600v basic digital multimeter, 200 microamp 10amp), auto off, on off buzzer, data hold, function protection and shock proof protection , 9 12v duracell rechargeable alkaline battery (pack of 2) , (9 v) battery holders to hold 2 batteries , 1.2v aa duracellbattery set of 4 , 4 (1.2v) aa battery holder , universal battery charger duracell for aa, aaa and 9 v duracell batteries , precision screw driver set (6 popular sizes)& can be used with electronics, watches, laptops, cameras, computers, small appliances, etc , humanoid robots min. 40 x 15 min 1 head, one main body part, two arms and two legs min 17 dof (1 dof of head, 4 dof of arm, 6 dof of legs, 2 dof of feet, 2 dof of the shoulder, 2 dof of hips) arduino uno r3 based usb 18 servo controller metal parts with smooth surface & edges robotic unit should be self sufficient to build the robot and should contain other accessories including servos, servo brackets, waist brackets, screws and screw cap sets etc. can be programmed and the code can be deployed on the controller on board making the robot autonomous software shall be used to program the hardware components like robotic arms , walkers, bipeds & other servo controlled system provided with software &media , rechargable battery & other required accessories to run the robot , robotic arms min 40 cm in length min 6 degree of freedon with 180° rotation angle should have parallel jaw gripper high torque standard servo motor with metal gears robotic arm should be self sufficient to build the robotic arm and should contain other accessories including servos, servo brackets, aluminium brackets, jaw gripper,bearing, metal horn, rotating assembly,screws and screw cap sets etc. software shall be used to program the hardware components like robotic arms provided with software &media ,rechargeable batteries & other required accessories to run the robotic arm , rasberri pi 4 with 3.5 inch lcd display , electronic kit containing following test leads with clips (min. 50 pieces 50cm double ended crocodile clips cable alligator clips wire testing (red and black) wire cutter (1 piece, 6 inch wire cutter and wire stripper with sharp edges &high grade steel) jumper wire (120 pieces jumper wires (40 pcs male to male, 40 pcs male to female, 40 pcs female to female) resistor kit–complete resistor kits with 20 different resistance values each assorted, packaged together and labelled ( minimum 5 resistors of each type ) switch:(10 pcs each: push, toggle, rotary,selector and slide switch) variable resistor / potentiometer:(3 nos, 3 terminals, single turn, carbon rotary taper potentiometer ldr : (50 nos. photo resistor / light dependent resistor) capacitor kit: complete capacitor kits with 18 different capacitance values (both ceramic and electrolytic included) each assorted, packaged together and labelled &(minimum 10 capacitance of each type) diode kit : 25 assorted basic diodes , 4 of each type (total 100) transistor kit : (10pcs each of 2n7000 n channel transistor fast switch mosfet to 92) and 5 pcs each of s9012, s9013,s9014, s9015, s9018, a1015, c1815, a733, c945 2n5401, 2n5551, s8050, s8550, 2n3906, 2n3904, bc547, pnp transistor, 1n4148, power diode 1n4004/4001 relay: 3 pieces, 5v, 4 channel relay board which can be controlled directly by a wide range of arduino microcontrollers integrated circuit: 3 pcs, la4440 zip14 dual channel audio power amplifier integrated circuits ic minimum 8 watt hook up wires – min 50 set of wires , sensor kit containing following 3 pieces, obstacle sensor 2cm 450cm. high precision: up to 2mm, input trigger signal: 10us ttl impulse, echo signal: output ttl pwl signal 3 pieces, triple axis magnetometer tri axis angular rate sensor (gyro) with a sensitivity up to 131 lsbs/dps and a full scale range of ±250, ±500, ±1000, and ±2000dps 3 pieces, temperature & humidity sensor 20 pcs ir transmitter & receiver diode 940nm 850nm 5mm lamp transmitting and receiving distance: about 7 8 meters 3 pcs, ultrasonic sensors 3 pc, cmos ir camera module isp with noise cancellation and dead pixel compensation, support image scaling, noise reduction automatic adjustment 1 pc, (5 rfid tags/ cars and 1 rfid reader) card reading distance 0 30 mm 3 pcs, rf modules tx & rx 315 mhz stx882 transmitter modulewith transmitting power of 10mw and srx882 receiver module 1 pc, voice recognition module speech recognition module with microphone dupont jumper wire speech recognition voice control board for arduino compatible. 3 pcs, mq3, smoke gas alcohol detection module sensor module for arduino 3 pcs, metal touch sensor 3 pcs, pulse rate sensor 3 pcs, colour detection sensor , robotic components including following 3 pcs, stepper motor with driver board 4 phase, 5 wire good quality stepper motor with uln 2003 driver board 3pcs, dc motor geared motor 200 rpm 12v dc gear for robotics, no load current: 800 ma (max) and load current: 9a (max) 3 pcs, 4 wide wheel acrylic car chasis kit with ultra sonic sensor, 300 rpm motor,with motor and battery holder 2 pcs, diy metal robotic kits with list of 20 experiements including motors, metal pieces, screws, gears, sensors, bolts, allen keys, manual / programmable brain with 2 drone kits , mechanical equipment’s including following • hacksaw rigid & balanced frame with carbon steel pipe rectangular heavy gauge pipe • chisel set 3 piece wood chisel set (1/2 x 7 3/4, 3/4 x 7 3/4, 1 x 7 3/4) • pliers suitable for live wire working and household applications • mini hacksaw back blade stop for safe handling and use • ball pen hammer meets the ansi specifications, 12.2 x 3.4 x 1.1 • steel shaft claw hammer designed for: striking application • c clamp all parts are fully heat treated and black phosphated ideal for heavy duty application • drilling work station 3 in 1 workstation, drill press, rotary tool holder, and flex shaft tool stand • 12 piece combination spanner chrome vanadium steel and nickel chrome plating protects against corrosion • param socket adjustable wrench open end wrench 2 pcs snap n grip tool spanner chrome plated surface treatment, beautiful and durab • 14 piece ratcheting screw driver set durable hardened chrome vanadium steel (cr v) bits with corrosion resistant finish. • baby vice 60 mm utilitarian baby vice made from cast iron • hot glue gun + glue sticks hot melt glue gun kit to be used as an adhesive tool in dry crafts making and also in daily quick repairs • soldering iron kit adjustable temperature (200 450 degrees) using dial given on the handle. • dual temperature heat gun helpful in removing the old paint before renovation or drying new coats of paint • return measuring tape tough abs case, durable steel blade, polymer coated blade for long life • stainless steel ruler used for distance measurement. • digital vernier calliper an ideal tool of this stainless steel digital caliper vernier with lcd display screen • 12” spirit level strong and precision extruded which increases accuracy and strength of the spirit levels • digital pen electric tester suitable for direct detection of 12v 220v ac and dc and indirect detection of the zero line, phase line of ac and the detection of breakpoint , instructor (robotics /embedded/3d printing) , 3d printer , pla (blue/white/yellow)...
Due Date : April 07, 2022
Tender Value : ₹ 1.90 Crore
