36504831
supply of furniture in tad girls hostel, multipupose hostel and additional commisioner office for tribal area development department ( tad ) at hq_jodhpur near lucky international, by pass road, kudi bhagtasani, jodhpur , supply of executive table with side unit table size – 2400mm table top length, 1200mm table top breath, 750mm table height. 25mm thickness table top made in post forming both end of table plain side to be 2mm edge banded. all modesty panel are of 750mm in width made in 18mm pre laminated board with 0.8mm edgbanded. gable panel should be of 675mm height from the top. bottom of the table having footrest and on right side of the table having 3 equal drawers. all drawer fitted on 400mm telescopic channel, having computer key locking systemon first drawer and rest without lock having steel handles. side table of 1200mm length x 450mm breath x 750mm height. table top made of 25mm thickness table top made in post forming both end of table plain side to be 2mm edge banded having single drawer, keyboard, cpu and ups stand at bottom. all exposed parts to be edge banded with 0.8mm. including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of executive recliner chair executive recliner boss chair having extra heavy base of 600mm with 60mm wheels attached, 80mm gas lift attached, torsion bar plate mechanism, structure of the chair should be made in complete wooden structure, fully upholstery of 125mm foaming in complete seat and back handles of wooden finish with cushion on them, in right handle there must be switch for reclining of backrest, reclining system must be there with small hydrolic below the chair, chair having premium leatherette finishing, chair seat size 550mm depth x 525mm width, backrest size 775mm height x 700mm width, arms size 300mm height x 75mm width x 475mm length.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of executive table with side unit table size – 1800mm table top length, 900mm table top breath, 750mm table height. 25mm thickness table top made in post forming both end of table plain side to be 2mm edge banded. all modesty panel are of 750mm in width made in 18mm pre laminated board with 0.8mm edgbanded. gable panel should be of 675mm height from the top. bottom of the table having footrest and on right side of the table having 3 equal drawers. all drawer fitted on 400mm telescopic channel, having computer key locking systemon first drawer and rest without lock having steel handles. all exposed parts to be edge banded with 0.8mm.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of sofa 2 seater seat foam?: ?the seat is made of pu ?foam with density ?28?± ?2 ?kg? / ?cu?.?mtr having an ?additional top layer of super soft ?pu foam indensity ?32 ?± ?2 ?kg? / ?cu?.?upholstered with fabric ?or leatherette?. ?back ?foam?: ?the back is ?made of pu foam with ?density ?28 ?± ?2 ?kg? / ?cu?. mtr with two additional ?top layer of supersoft ? foam of density ?32?±?2 ?kg? / ?cu?. ?mtr?, ?upholstered ? with fabric or leatherette .understructre ?: ?understructure is made ?up of ?1?.?2?±?0?.?1 ?cm?. ?thick ?hot pressed plywood ? ( moisture resistance & termite proof as per is: 303 ) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat &3.8 mm dia zigzag spring assembly is mounted over understructure for cushioning purpose. leg assembly?: ?it is ?a welded assembly ?made in stainless steel ? ( ?grade ss ?202? ) ?tube ?& ?plate? with plastic endcap. ( w ) 146.0* ( d ) 90.5 ( h ) 85.5 cmseat ( h ) 45.0 cmincluding all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of 3 seater sofa seat foam?: ?the seat is made of pu ?foam with density ?28?± ?2 ?kg? / ?cu?.?mtr having an ?additional top layer of super soft ?pu foam indensity ?32 ?± ?2 ?kg? / ?cu?.?upholstered with fabric ?or leatherette?. ?back ?foam?: ?the back is ?made of pu foam with ?density ?28 ?± ?2 ?kg? / ?cu?. mtr with two additional ?top layer of supersoft ? foam of density ?32?±?2 ?kg? / ?cu?. ?mtr?, ?upholstered ? with fabric or leatherette .understructre ?: ?understructure is made ?up of ?1?.?2?±?0?.?1 ?cm?. ?thick ?hot pressed plywood ? ( moisture resistance & termite proof as per is: 303 ) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat &3.8 mm dia zigzag spring assembly is mounted over understructure for cushioning purpose. leg assembly?: ?it is ?a welded assembly ?made in stainless steel ? ( ?grade ss ?202? ) ?tube ?& ?plate? with plastic endcap. ( w ) 206.0* ( d ) 90.5 ( h ) 85.5 cmseat ( h ) 45.0 cmincluding all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of center table overall size : width : 120cm depth : 65cm height : 43cmtable materials: glass of 08 mm thk tempered, solid rubber woood legs and frame, ms sheet as bottom shelf .decoration materials & specifications: ( density / type ) : pu coating to the rubber wood parts, clear glassincluding all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of tea table overall size : width : 750cm depth : 65cm height : 43cm table materials: glass of 08 mm thk tempered, solid rubber woood legs and frame, ms sheet as bottom shelf .decoration materials & specifications: ( density / type ) : pu coating to the rubber wood parts, clear glassincluding all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of executive revolving chair heavy duty steel finish base of 650mm with 60mm 5 wheels attached, class 3 gas lift, torsion bar plate mechanism, single l ply 15mm attached with 40 density foaming in seat and back 100mm cushion in seat and 100mm cushion in back to be double cushioned. upholstery material of leatherette. handle should be attached in seat and back with cushion on it. size of seat should be 500mm width and 475mm depth. back size 750mm height and 500 width.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of 3 seater commom arms the seat shell should bea welded assembly of seat, back and side frame. the seat and back should bemade of 0.15±0.013cm thk cr steel sheet with oblong perforations.they should bewelded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should bepowder coated ( dft 40 60 microns ) . the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. * seat size : 47.8 cm ( w ) x 44.6 cm ( d ) * back size : 41.6 cm ( w ) x 23.0 cm ( h ) understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should bepowder coated ( dft 40 60 microns ) .the leg assembly should befitted with shoes and levellers in nylon. the leg structure should bedesigned with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould beof uneven flooring.connecting beam should befitted with snap locking end cap.lt also aids in side by side understructure alignment .armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should bemade up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should bepowder coated ( dft 40 60 microns ) . armrest pad should beinjection molded in nylon and should befitted onto the armrest frame. overall dimensions of chair seat height 44.1 cm. height 78.5 cm. width & depth of chair as width 169.5cm and depth 63.8 cm. including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of operator table with file cabinet table size – 1500mm table top length, 750mm table top breath, 750mm table height. 25mm thickness table top made in post forming both end of table plain side to be 2mm edge banded. all modesty panel are of 600mm in width made in 18mm pre laminated board with 0.8mm edgbanded. gable panel should be of 675mm height from the top. footrest should be there in rest of the bottom part of table. right side of the table having 1 drawer and 1 cupboard. drawer fitted on 350mm channel having computer key locking system. cupboard fitted with auto hinges and having computer key locking system. handles should be of steel both in drawer and cupboard. drawer size 350mm width x 375mm depth. all exposed parts to be edge banded with 0.8mm.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of computer table with cpu hanger size shall be 1200 width mm x 600 depth mm x 728 heigth mm. top shall be 18mm thick pre laminated particle board all work surface edges duly sealed with 2mm thick pvc edgebanding. the rectagularngular frame shall be fabricated component in 1.2mm thick crca, finish : powder coat ( epoxy polyster ) coated to the thickness of 50 micron 1.2mm thick ms erw a tube, finish powder coat ( epoxy polyster ) , wire management horizontal wire carrier 0.7mm thick crca finish power coat ( epoxy polyster ) and vertical wire carrier 0.8mm thick crca finish powder coat ( epoxy polyster ) coated to the thickness of 50 micron ( + 10 ) .including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of executive visitor chair non revolving the seat shall be made up of 1.2+ / 0.1 cm thick hot pressed plywood & upholstered with leather and moulded polyurethane foam. the back shall be designed with contoured lumber support for extra comfort. size ofback shall be ( w ) 53cm x ( h ) 73cm & size of seat shall be ( w ) 54.6cm x ( d ) 49cm. high resilience ( hr ) moulded foam should be used in making seat & back. the fixedtype mechanism shaal be made with a 0.8+ / 0.05cm thick hr steel spine welded to it and black powder coated. overall dimensions of chair shall be width of chair 59cm, depth of chair 68.5cm as measured from pedestal below. height of back from ground 89.5cm. seat height 46.5cm. dimensions tolerance / variations shall be within + / 1cm. including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of visitor chair with arms in fix seating with full cushion on seat and back. seat size 450mm width x 450mm depth. backrest size 450mm width x 525mm height. chair structure made in 16 gauge 1” round pipe with ¾” pipe duly inserted in 1” pipe for better durability. 2 ms flats welding on iron frame of size 25mm width and 6mm thickness for seat. backrest support structure having lms flat of 50mm width and 10mm thickness. seat and back ply should be 12mm hot press. 75mm thickness 40 density foam in seat, 70mm thickness 40 density foam in backrest covered with matte fabric. arms on the chair should of ms covered with pu connected with bolts from bottom. exposed parts of the iron structure to be powder coated with 50 micron.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of office iron almirah almirah having 4 fix shelves make in 0.8mm thick crca for shelf, top, bottom, back and doors complete. size of the almirah shall be 1980mm ( h ) x 910mm ( w ) x 480mm ( d ) . the locking and handle shall be mazak handle with three way locking mechanism. the finish of the almirah should be of steel grey colour in powder coated with 50 microns. almirah should be provided with balanced 2 foots at the bottom welded with almirah.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply & fixing open iron rack size 1875mm ( h ) x 900mm ( w ) x 300mm ( d ) having 6 nos. shelves 1mm thick m.s. sheet powder coated & angle post having rolled steel powder coated angle size 40x40x3 with pigon hole as required.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of acrylic writing desk office table top elevator with slant adjustable height for easy reading / writing study table ( big size 24x18 inches ) 12 mm thickness.clear transparent, cell cast acrylic sheet, a grade, 100% virgin monomer madewith 5 degree angle adjustment with metal frame.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of woods stylish natural wood office under table footrest, under desk foot stool, leg support with heavy duty super quality feet relax item ( wooden dark brown ) item dimensions 440mm ( l ) x 290mm ( w ) x 120mm ( h ) . heavy duty anti slip comfortable for under desk foot stool, feet relaxation while prolonged sitting.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of 12mm thick plan glass having size 2400mmx1200mm & 1200mmx450mm.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of wooden framedwall hung notice board size foam cushioned fabric ( inner size : 120mm x 900mm ) with wooden frame and attractive foam cushioned green fabric in front ( hides pin holes ) and back is laminated to make water proof surface. outer decorative frame 50mm wide of teak wood polished.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of the back unit size shall be 1400 width mm x 470 depth mm x 1200 height mm. the top panel size shall be 25mm thick mfc ( melamine faced chipboard ) . the door panels and all other panels should be 18mm thick mfc ( melamine faced chipboard ) the handle shall be of metal.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of sigle bed without storage made by ms square pipe size 1800mm x 900mm ( size of mattress ) main frame of bed made in 50x25x1.5mm ms square pipe main frame consist four side with 50x25x1.5mm square pipe headsest height from ground = 685mm at legs side 450mm height from ground 12mm mr grade ply fitted inside the iron frame, slanted support between legs and main frame in both sides, total 5 ms pipe 25x25x1.5mm support to ply with well bolted, headrest of bed have 3 horizontal support and legs side 2 horizontal and 2 vertical support powder coated black colour, plastic shoes shouldbe fitted in legs.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , student table 600mm ( l ) x 450mm ( w ) x 600mm ( h ) with mdf laminated top. size of squqre pipe ( both for frame and supports ) of ms 25mm x 25mm 16 guage. legs should have h support. min. weight without board 6 kg. painted with red oxide coat & paint. , student chair 450mm x 405mm x 450mm ( height ) , back 450mm x 405mm. size of square pipe for frame & legs 25mm x 25mm 18 gauge of ms sheet size for sitting & back 22 gauge. min. weight 7.0 kg. painted with red oxide coat & black paint. , supply of student chair with writing pad frame & legs : the frame shall be made out of diameter 25mm tube of 1.6mm thick, welded by co2 welding process for uniform surface finish and higher tensiie strengh the perforation on the sheet be uniform of 2.5mm dimension. back & seat : ms perforated sheet of1.2mm thock with powder coating ( dft 40 50 microns ) . writing desk : made out of 12mm thick mdf board on foldable basis. the desk size shall be broader ( 290mmx450mm from the front & tapering ( 290mmx100mm ) towards the elow. the ms powder coated hindge shall be of size 100mm w.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of the podium size shall be 750mmx550mm ht. shall be made up to of 16mm thick paper laminated mdf board, having 1 nos. pvc cable manager.including all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of 3 seater bench for dining table 1800mm x 450mm x 450mm ( height ) made out of 16 swg ms seat top with tube section for panel and support 40x25x1.5mm thick. properly powder coated & smoot finishincluding all taxes & for.. ( design and other specification as per direction of engineer in charge ) , supply of dining table size 1800mm x 750mm x 750mm top ms pipe frame ( size 1725mm x 675mm ) made by 50mm x 25mm x 1.5mm ms pipe with two intermediat support lenght 675mm made by 25mm x 25mm x 1.5 mm ms pipe. four nos. vertical post 750mm height made by 40x40x1.5mm ms pipe. vertical post connected to each other above 150mm height above ground level by ms pipe 25x25x1.5mm in both direction. dining table top ( size 1800mm x 750mm x 750mm ) 18mm thick rajasthan black / jalore grainet fix with frame by adhesiv and screwed with ms frame table top all for edges 18+18 = 36mm thick by 40mm wide grainet pati and 40mm projected with full moulding. including all taxes & for.. ( design and other specification as per direction of engineer in charge ) ...
Due Date : March 10, 2023
Tender Value : ₹ 23 Lakhs
