Department Of Atomic Energy - Rajasthan

39378131 bids are invited for custom bid for services removal of back pull out assembly and installation of spare back pull out assembly of pump having motor rating up to 60 kwe. decoupling, alignment and coupling of pump and motor having motor rating up to 60 kwe. overhauling of motor of rating from 30 kwe to 60 kwe. overhauling of manual operated valve or overhauling of non return valve or overhauling of air operated piston / flapper type actuator. maintenance of actuator of control valve having diaphragm maintenance of shutdown cooling pump having motor rating 95kwe for in service inspection as per scope of work opening and boxup of shutdown cooling heat exchanger / moderator heat exchanger opening and boxup of both primary sides ( hot leg & cold leg ) man hole covers of one steam generator for isi. removal and installation of secondary side hand hole covers of steam generator for isi & water jet cleaning. preventive maintenance checks of osu tank as per scope of job preventive maintenance checks of primary circulating pump ( pcp ) and its motor. overhauling of electrical actuator operated / piston type air actuator operated valve guide nut inspection of emergency core cooling system / shut down cooling system motorized valve having valve size: 8 inch to 12 inch. preventive maintenance checks of emergency core cooling system shut down cooling system motorized valve having size: 8 inch to 12 inch. overhauling of control valve with valve size upto 6 inches. overhauling of motor with electrical rating from 65 kwe to 400 kwe. preventive maintenance checks of primary pressurizing pump. replacement of door seals of reactor building main air lock equipment door. replacement of main air lock vacuum pump / emergency air lock vacuum pump / vacuum moping pump. preventive maintenance checks of manual bellow sealed valve. diaphragm replacement of diaphragm valve. diaphragm replacement of diaphragm valve. replacement or cleaning of strainer / filter replacement of relief valve flange gasket replacement and tightening flange / threaded joint tightening removal of snubber for testing and installation after testing replacement of primary circulating pumps motor having rating 2800 kw. overhauling of spare back pull out assembly of oil supply unit pumps having motor rating less than 30 kwe at mmu shop. replacement of lobe type blower. feeder gap measurement manual axial creep measurement & adjustment removal and installation of zig saw panel removal and installation of step panel / insulation panel coolant channel repositioning pss drive lower chamber o ring replacement, wire rope inspection & gear train / clutch gap inspection pss drive upper chamber replacement mock up & preparatory activities for cobalt element replacement job regulating rod element replacement in reactivity mechanism drives. qualification on barcis mock up, erection of barcis set up on fm bridge, removal from bridge and decontamination. inspection activity of coolant channels by barcis shifting of barcis drive to / from x drive from / to launching table total quantity :...

Department Of Information Technology - Rajasthan

37990809 request for proposal for overall operation and maintenance and fms of non it equipments installed at dr site of rsdc at jodhpur, rajasthan 1 double uneven leaf fire rated steel door withvision panel: ss ball bearing butt hinges, lock, ss lever with the internal thumb turn & external key operation with heavy duty door closer 2 single leaf fire rated door with vision panel: ss ball bearing butt hinges, lock, ss lever with the internal thumb turn & external key operation with heavy duty door closer 3 tile puller 4 bms and it support staff work station: 60 mm tile based system including tiles.height of system will be 1200mm.system has one mdf marker board & one fabric pinup board inner side above worksurface & metal tile below worksurface at inner 1 mm thick crca. side.system has metal tile at outer side. work top size 1200mmx600 mm.table tops are of 25mm thick & gable ends are of 18 mm thick pre laminated particleboards icroproce to is:12823 interior board confirming to is:12823 interior grade with matching pvc edge banding. all the exposed edges are sealed with 2mm thick imported pvc edge banding on sides & bottoms. the top & drawer facia are sealed with 2mm thick pvc edge. the drawer unit consists of 2 box drawer & 1 file drawer. the sides of inside drawer box are of prelam particle board. the drawer box is fitted with roller slide for free movement. the drawer unit is provided with central locking system, where in the three drawer are locked with one key. pvc recessed handles are provided for easy opening and closing of drawer. the drawer unit is fitted on casters ( optional ) for easy mobility. the complete furniture unit is factory assembled with knock down fittings. the pedestrial is lifted with additional ( 5th ) castor to avoid icropro of pedestral in case of opening of any / all of the three drawers. cpu trolly: the base is made of 1.6 mm thick crca and the sides are made of 1.2 mm thick. the width of the trolley can be varied to accompany various width cpu.the cpu is mounted on locable castors. keyboard: outer dimension of keyboard tray is 507x245 mm made of 5 dc manager / it supervisor table : size 1650x750x740, side table 1050x450x740, pedestal 350x450x550, back storage 1050x425x700 6 productivity work chair: smart mid back, s1 mechanism, t fixed arm, nylon base, nylon castor 7 long back executive chair: high back, synchro 1 mechanism, 1 d arm, nylon base and nylon castor 8 designer type reception desk: 20000 mm ( w ) x600mmwith1200mmhigh , 75mmthk. customized with glass topwith arrangement of key board trays, cpu trollys, three drawer, etc. complete as per customer 9 conference round table: 25 seater as per design approved by engineer in charge 10 sofa set with 3 + 2 seating arrangement along with tea table 11 shoe rack for 100 pairs shoes: 6’’ ( h ) x 10’’ ( w ) x 1’ 0” ( d ) made from 19 mm bwr and termite proof board for frame / partition , back side made of 12 mm thick ply and duly painted with enamel paint, unique numbering on each box with enamel paint, second class teakwood corner beading andbottom of unit will have proper legs / stands / wooden 12 lockers for keeping essentials for 100 person: 1’ 0” ( h ) x 1’ 0” ( w ) x 2’ 0” ( d ) made from 19 mm bwr and termite proof board for frame / partition and shutters ( single leaf shutter size 1ft. x 1ft. ) , back side made of 12 mm thick ply and duly painted with enamel paint, each shutter fixed with two numbers stainless steel butt hinges of 2.5” and a knob handle on each shutter with lock, stopper on inside face, unique numbering on each box with enamel paint, all exposed faces of wood work finished with veneer ply 1 / 8 inch thick and second class teakwood corner beading on front side and corners of shutter polished with polyurethane ( pu ) polish, bottom of unit will have proper legs / stands / wooden 13 fire safe : fire safe ( 170lts ) of godrej make ( model no fr 1060 ) with hight 1060 mm, width 450 mm & depth 355 mm for media / backup 14 door signage’s: vinyl cutting on acrylic base. ( size : 12”x4” ) 15 data centre name plates: data centre name plates / display boards ( 3 ft x 4 ft size ) with decorative light fitting as per design approved by engineer in charge 16 white board: size 4 ft x 5 ft with duster and proper floor mounting stands 17 fire escape route flow diagram: a1 size 18 fire escape exit board 19 stainless steel water cooler with nominal cooling capacity: stainless steel water cooler with nominal cooling capacity / storage capacity of 60 / 120litre / hrs 20 tea / coffee vending machine triple option that can make tea coffee soup & give hot water. vending machine should have auto water flushing after selected time facility digital meter to count no’s of drink dispensed display water level sensor 21 modular storage: depth 450mm*2500mm ( with openable hinged doors at required intervals ) with laminated finish on both inside and outside 22 modular control desk for 01 monitors & 01 operator : dimension: 750mm ( h ) x 750mm ( w ) x 900mm 23 12mm thick frameless tempered clear glass single door with 100mm metal frame : tempered glass is formed by heating glass to the softening point in a horizontal tempering stove, and then quickly cooling it. properties: 1 ) safety ( tempered ) : when broken, it spits into tiny harmless pieces 2 ) strong intensity: heat strengthened glass is approximately twice as strong as annealed glass of the same thickness, andtempered glass is about 4 times 3 ) outstanding performance in resisting thermal stress and wind load 4 ) tempered glass cannot be cut, drill hole and other further processed. 24 round led ceiling light: high performance led downlighter with high system efficacy for good quality and uniform lighting. conforms to general lighting norms for office and other indoor applications 25 ht panel 11kv gang operated switch: complete in all respect with mounting structure 26 transformer : 1250 kva, 11kv / 433v, vectorsymboldyn11, z=6.25%, delta / star connected, onan, ester oil type, 3phase / 3 phase neutral, outdoor type distribution transformerwitholtc andcompletewithallstandard accessories, htcablebox, suitable flanges for 2000a busduct on secondarysideetc.transformersshallbedesigned for 45 deg 27 isolator panel ( 2000amp ) ( schneider ) 5 nos relay – master relay ( 1 nos. ) , trip circuit relay ( 1 nos. ) , vmr relay ( 1 nos. ) and earth faulty relay ( 2 nos. ) . 28 lt panel: 415v main lt panel, suitable for 415volts 3phase 4wiresystem, fabricated from 14 / 16swg crca sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top / bottom, complete with internal wiring, ferrules, name plates, painting etc 29 row power panal: 250a, 4p 30 ka, mccb having electronic trip unit with adjustable protection against overload and short circuit 30 pac panel: 400a, 4p 30 ka, mccb having electronic trip unit with adjustable protection against overload and short circuit 31 ups output pdu panel: 630a, 4p 15 ka, mccb having electronic trip unit with adjustable protection against overload and short circuit 32 vrv panel: 160a, 4p 25 ka, mccb having electronic trip unit with adjustable protection against overload and short circuit. 1no – load manager with modbus over rs 485 interface with maximum demand indication of em 6400 or equivalent. 1set – 160 / 5a, class 1.0, 15va for metering, cl.ps, 15va for protection cast resin cts 33 emercency panel: 63a, 4p 25 ka, mccb having thermal magnetic release with adjustable thermal setting incomer metering for each incomer 34 isolation transformer panel: 300kva k13 isolation transformer outgoing 35 liftpanel: 100a, 4p mccb having thermal magnetic release with adjustable thermal setting metering for incomer 36 apfcr panel – 450kvar: auto power factor correction relay ( apfcr 450kvar with 5 stage rating 4x100 kvar + 1x50 kvar design as per iec 61921, iec 61439 1 & 2 ) suitable for 415volts 3phase 4wiresystem, fabricated from 14 / 16swg crca sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, bus duct flange for incomer, gland plates at top / bottom for control cables, complete with internal wiring, ferrules, name plates, painting etc 37 auto transfer switch 100a, 415v, 4p: powder coated enclosure with ip 55 100a, 415v, 4p, auto transferswitchhousedinweatherproof, crca sheet / msbox powdercoatedenclosuremounted onmssupportnearthe pumps suitableforoutdoor application of ip55.ats should be able to accommodate 4c x 35 sqmm cu arm cable on load side as per sld and all complete as per drawings 38 auto transfer switch 40a, 415v, 4p: weather proof, crca sheet / ms box enclosure mounted on wall near the pahus suitable for indoor operation as per sld. ( powder coated with ip55 protection ) and all complete as per drawings 39 auto transfer switch 63a, 415v, 4p: weather proof, crca sheet / ms box enclosure mounted on wall near the pahus suitable for indoor operation as per sld. ( powder coated with ip55 protection ) and all complete as per drawings 40 dg sync panel: 415v dg sync panel 1, suitable for 415volts 3phase 4wiresystem, fabricated from 14 / 16swg crca sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top / bottom, complete with internal wiring, ferrules, name plates, painting etc 41 40w surface mounted led light fixture 2 feet x 2 feet 42 occupancy sensor range 6 7 meter 43 3ø, 8way, phase segregated db ( lighting db ) : incomers 1no. 63a, 4p, mcb ‘c’ curve phase outgoing 3nos. 63a, 30ma, dp, rccb 12nos. of outgoing 6a sp mcb with ‘c’ curve 12 nos. of outgoing 16a sp mcb with ‘d’ curve 44 3ø, 8way, phase segregated db ( raw power db ) : incomers 1no. 100a, 4p, mcb ‘c’ curve phase outgoing 3nos. 100a, 30ma, dp, rccb 12nos. of outgoing 6a sp mcb with ‘c’ curve 12 nos. of outgoing 16a sp mcb with ‘d’ curve 45 1250 kva transformer earthing 46 750kva dg set earthing 47 lightning arrestor earthing 48 ups / pdu system earthing 49 rack earthing 50 ht panel earthing 51 lt panel earthing 52 lightning arrestor enchanching type designed to attract lightning: lightning arrestor enchanching type designed to attract lightning from a predetermined volume and to safety convey the lightning current to the earth and complaint ul 96 or equivalent to nfc 17102 ese type ( nimbus ) and complete with following principle components. ( the lightining icropro should cover 107meter radius and as per site requirement ) & air termination shall be non corroding and centre earthed finials shall be 300mm in cross section and be made of electric grade non ferrous material 53 round bottomed fire buckets filled with river sand 54 shock treatment chart in english & hindi languages laminated / glass framed 55 11kvdanger boards 56 440v danger boards 57 first aid box containing full compliment of medicines, ointments & bandages 58 single line drawing duly laminated / framed in a1 size 59 60x40cm teak wood box with glass door & hooks for hanging keys & space for keeping hand gloves complete with lock & three keys 60 300 kva / kw ups: igbt based rectifier to achieve input thdi < 3% and input power factor of greater than 0.99 at 100% loading. true online double conversion ( vfi as per iec 62040 3 ) ups usingpwm igbt technology, 3 phase input and 3 phase 415 v output ups system 61 40 kva ups with 3 phase input and 3 phase output: 3 phase input and 3 phase output and as per the technical specifications. quoted rate shall be inclusive of required batteries of 15 minutes back up at full load, battery shall be with connecting cables, battery rack and all complete as per drawings, technical specifications, sld, relevant standards 62 dg sets 750 kva: 3 phase 415 volts 50 cycle per second 1500 rpm radiator cooled diesel generator sets of rating as below. the engine shall include flywheel to suit flexible coupling with guard, air cleaner, blower fan, fuel pump, variable speed electronic governor, fuel filter, lub oil filter & pump, primary water circulating pump, battery charger, 24 volt batteries of compatible capacity with battery stand and instrument panel comprising of switch with key 63 12 hours running capacity bufferfuel tank: receive fuel oil from bulk oil storage tank, fabricated from 2 mm thick m.s. sheets including the cost of removable cover with locking arrangement and including the cost of painting and including the cost of providing all the required appurtenances like inlet and outlet connections including the cost of flanges & fittings, float valve, foot valve, drain connection, over flow connection to oil sump etc. and including the cost offuel level sensors with high and low level visual indication and audible alarms with actuators to automatically start and stop the fuel 64 semi rotary hand pump for filling fuel 65 no smoking & danger zone sign boards 66 co2 4.5 kg capacity as per is:2878 67 fire extinguisher chemical foam type of 9 litre 68 fire extinguisher dry chemical powder type is : 2171 5 kg 69 precision air conditioning system ( 26 tr ) :microprocessor based precision air conditioning units for the server room.the unit shall be complete with incoming mccb, inverterdigital / tandem / scroll compressor , cooling coil dx type, with eev, ec drive with plug fan, microprocessor panel, air filter, electrical reheat, built in sequential controller, air cooled condenser 70 precision air conditioning system ( 9.5 tr ) : microprocessor based precision air conditioning units for the server room.the unit shall be complete with incoming mccb, inverterdigital / tandem / scroll compressor , cooling coil dx type, with eev, ec drive with plug fan, microprocessor panel, air filter, electrical reheat, built in sequential controller, air cooled condenser 71 vrv based air conditioning: multi vrf units complete with 100% inverter driven scroll compressor, air cooled condenser with inverter driven icropro speed fan motor having interconnected control wiring and refrigerant piping housed in compact housing duly powder coated body. 22 hp ( cooling only ) 52 deg.operation 72 indoor comfort ac units: 4 way cassatte unit ( 3tr ) 73 indoor comfort ac units: msp ductable ( 4.6tr ) 74 indoor comfort ac units: hi wall ( 1tr ) 75 indoor comfort ac units: hi wall ( 1.5tr ) 76 indoor comfort ac units: wireless remote 77 wired remote 78 centralize remote ( touch type ) 79 ul listed server racks: size minimum. 600 mm ( w ) x 1200 mm ( d ) height 42 u 80 ul listed server racks: size minimum. 800 mm ( w ) x 1200 mm ( d ) height 42 u 81 telco rack for mux and hub room 82 cold aisle containment system 83 fire alarm panel with network interface card ( 2 nos. ) , telephone zone card 1 nos. ) , zone indication card ( 1 nos. ) , digital audio card ( 1 nos. ) , device loop card ( 2 nos. ) and with accessories ( siemens ) 84 repeater panel including display of minimum of 80 characters 85 multi sensor smoke detector 86 fixed temperature cum rate of rise heat detector: ul listed fixed temperature cum rate of rate of rise heat detector with mounting based led, address switch / electronic way of addressing, as per technical specifications and all requirements of contract works 87 dual action ( push in pull down ) flush or surface mounted manual call point 88 addressable hooter cum strobe units, wall mounted 89 fire telephone jacks with telephone module complete7 90 heavy duty recessed / surface mounted telephone hand set complete 91 monitor module for mcp, vesda & wld panels 92 control module for hooter cum strobe and gas release panel 93 relay module 94 isolator module 95 bacnet card for networking 96 6 watt ceiling mount speaker with junction box for ceiling mount 97 15 watt wall mount speaker 98 240 watts booster amplifier 99 480 watts booster amplifier 100 voice alarm controller goosneck micro phone 101 usb / cd / mp3 player 102 6 zone selection panel for pa announcement 103 rack to mount amplifier, cd player and console 104 nvr: suitable power socket, dc power converters, connectors, cables, etc. complete as per spec. contractor to decide on the nvr size depending on the pixel resolution and recording rate in frames per second as specified in the tender. contractor shall size the nas for 25 fps / 4 cif resolution 90 days of recording and submit data sheet of their storage calculation for both mpeg 4 and jpeg recording formats and submit data sheet of their storage calculation for both mpeg 4 and h.264 recording formats. note: each minimum of 20 chanel capacity 105 large wall mount lcd screens 106 emercency door releaser 107 access card readers 108 proximity cards 109 break glass unit for access doors 110 biometric finger reader 111 electromagnet door holder single leaf door 112 electromagnet door holder double leaf door 113 door contact 114 card printer 115 rodent satellites ( streem ) 116 vesda 117 fire suppression system 118 master cylinder kit 119 end slave cylinder 120 el check 2” ( manifold check valve ) 121 gas discharge nozzles 122 abort switch 123 release switch 124 water leak detection panel ( 4 zone ) 125 outside t / rh sensor 126 room t / rh sensor 127 8 port managed non poe switches 128 20 port managed poe switches 129 fixedtypedelegate unit 130 fixedtypechairmanunit 131 fixed dome camera: cctv including networking items such as switches, patch panel, liu, patch cords etc.required for the completeness of system as per the building drawing attach with rfp 132 ptz camera: outdoor ip based pan / tilt / zoom cameras, ½.9” progressive scan cmos or better, image resolution 1920 x 1080 or better @ 25 fps, electronic shutter 1 / 28000 sec to 1 sec or better, including integrated housing ( dome type ) , connectors, lens, camera mounting poles and all ancillary equipment& all accessories ( including driver cables , power supply unit & pan tilt unit ) 133 dcim ( athenta technology ) 134 data centre infrastructure management software per rack perpetual license for 80 racks and as per rfp specification. 135 dcim server 136 aoms server 137 fascia server 138 ddc panel ( siemens ) 139 ddc panel ( cabinet ) 140 rs 232 to 485 modules ( model number: tx12 s.open ) : the rs232 / 485 module integrates third party systems via rs232 or rs485 interface to the desigo building automation and control system. txi2.open supports up to 160 data points. the module status led ( green ) indicates the status of the module. 141 system controller ( model number: pxc001 e. d ) : mapping and monitoring of third party disciplines as hvac. the system controllers provide the infrastructure to hold and execute the system and application specific functions. the module status led ( green ) indicates the status of the module. use network interface rj45 for ( bacnet / ip, pxc001 e.d ) only. system controller for the integration of knx, m bus, modbus or scl over bacnet / ip. 142 digital input module ( model number: txm1.16d ) : a digital signal is a signal that exists in one of two states: high or low, open, or closed, on or off. a digital input / output ( dio ) device is hardware that sends or receives these digital signals. available 16 inputs in txm1.16d, each with a green led. 143 power supply module ( model number: txs1.12f10 ) : the device converts and supplies electricity of the required voltage and frequency, excluding noise from the electricity obtained from an electrical outlet. power supplies are classified by applications for available dc, ac, and output voltage ranges. dc 24 v for the supply of i / o modules and field devices ( generated in an internal ac / dc converter ) 144 bus connection module ( model number: txs1.ef10 ) : transfer of dc 24 v for the supply of tx series modules and field devices. ac / dc 12...24 v for the supply of field devices. 145 universal module ( model number: txm1.8u ) : all terminals are directly on the i / o modules, allowing direct connection of field devices without additional terminal strips. support of signal types and functions in different building automation and control systems. provide 8 inputs / outputs with led signal / fault indication. 146 relay module ( model number: txm.1.6r ) : the relay module function is mainly to switch electrical devices and systems on or off. it also serves to isolate the control circuit from the device or system being controlled. available 6 volt free relay outputs.individual i / o point signalling with green i / o status led. 147 automation station module ( model number: pxc200 e. d ) : freely programmable modular automation stations for hvac and building services plants. comprehensive management and system functions ( alarm management, time schedules, trends, access protection. high performance and reliable operation. 148 building management system 149 access control unit with accessories ( hid ) 150 bio metric workstation, ( dell ) 151 access control software ( security view & morpho manager ) 152 door contacts, ( hid ) 153 access management software with time & attendance software ( hr view ) 154 ptz camera joystick, ( dahua ) 155 web application for cctv, ( smart pss dahua ) 156 rodent repellent panel with stand and bracket, ( jay fire system ) 157 wld electronic hooter 158 wld module ( sim ) 159 wld sensor cable 160 building management system software ( desigo cc siemens ) 161 energy meter single phase ( tap up box ) ( starline ) 162 energy meter three phase ( tap up box ) ( starline ) 163 server room bbt with end feed unit ( starline ) 164 laser jet printer 1108 ( hp ) 165 laser jet pro mfp m181fw ( hp ) 166 lighting and power wiring ( as installed ) 167 upkeep and maintenance of standard wiring electrical points including wires, sockets / switches ( 6 amps, 16 amps & 32 amps ) . ( as installed ) 168 power wiring: upkeep and maintenance of standard wiring electrical points including cables from lt panel to raw power panel, ups, emergency panel, pac panel, vrv panel and apfc panel & from ups to pdu panel. ( as installed ) 169 asset management ( rf code ) 170 asset & environment management software ( centerscape ) 171 temperature & humidity sensor 172 single phase ipdu ( server technologies inc. ) 173 three phases ipdu ( server technologies inc. ) 174 rack locator 175 reader ( 6 installed in server room & 1 installed in store room ) 176 asset inventory tags 177 bbt ( 3 phase – 2000 amp ) from isolator panel to both lt panel, from dg set to dg sync panel and dg sync panel to lt panel ( schneider ) 178 modular wall panel ( installed in development and noc room ) ( pyrotech ) ( as installed ) 179 response indicator, ( agni ) 180 ring main unit ( 11kva ) ( schneider ) 181 iron gate 182 center table 183 vacuum cleaner ( shakti ) 184 drawer 185 file desk 186 almirah 187 air booster fan ( stulz ) 188 air extractor ( stulz ) 189 air modulator ( stulz ) 190 om4, bend insensative, pre terminated trunk cable, 24 fiber lszh, 13 meters 191 om4, bend insensative, pre terminated trunk cable, 24 fiber lszh, 10 meters 192 om4, mpo cassette, 24 lc fibers ( 12 duplex ports ) 193 2u ud shelf / panel, accepts 12 mpo cassettes 194 1u hd shelf / panel, accepts 12 mpo cassettes 195 1u sliding modular cassette shelf, accepts 4 mpo cassettes 196 network control station 197 sounder with strobe ( hooter ) 198 control unitfor conference room 199 industrial socket 200 esign project 201 access control with software ( 4 door_access_ctrl ) 202 access control ( fingerprint_access ) ( essl ) 203 access control ( face_detection_access ) ( essl ) 204 access control ( essl ) 205 dvr ( hikvision ) 206 led_tv ( micromax ) 207 iron cage ( 400 sq. feet approx ) ( as installed ) 208 fixed dome camera ( hikvision ) 209 push button for exit ( access control ) 210 essl em lock 211 other items 212 lift ( thyssenkrupp ) 213 hanging wall fan ( crompton ) 214 cabinettype rectangular inline fans with motor complete with tefc sq. cage inductionmotor suitable for 220 volts ± 10%, 50hz ± 3 %, single phase a.c 215 cooling only 5 hp capacity ( side discharge ) itc of vrf oem manufactured treated fresh air unit ( tfa ) equipped with pre filter, fan section with low noise fan, multispeed motor, coil section with dx coil, outer cabinet, insulated drain pan, pipe connections etc. 216 4.12 tr / 741 cfm tfa unit with wired remote 217 outdoor cubicle type totally enclosed free standing double door type dust & vermin proof kiosk panel for outdoor application made out of 2.0 mm thick and partition made out of 1.6 mm ms sheet steel, suitable for 3 phase , 4 wire , 415 v , 50 hz , ac supply complete with incoming acb / mccb / sfu & outgoing mcb / mccb / sfu , all the mccb should be with rotary handle, four pole electrolytic grade incomer100 amp, fp, 25 ka, mccb having thermal magnetic release with short circuit and adjustable overload ( 0.7 to 1in ) protection 1 no, busbar 200 amp, fp, electrolytic grade al busbar for mainmcb outing & feeders distribution, outgoing25amp, fp, c curve, 10 ka bc mcb 1 nos, 25amp, fp, ac1 utilisation catagary power contactor, having 415 volt operating auxiliary coil fitted with suppressor & 2no+2nc block 1 nos, 40amp, fp, c curve, 10 ka bc mcb 02 nos6amp, sp, c curve, 10 ka bc mcb 11 nos, digital time switch with 2 amp mcb for time switch bypass arrangement 1 nos, a software for communication, duly protected by 2a mcb 1 nos, led type ryb indication lamp duly protected by 2a mcb– 3 nos. 218 dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity 6kg. . 219 supply & installation of manager table ( 1500x750x770 ( lxbxh ) ) 220 supply and erection of pole lighting stell tubular swaged type with decorative pole conforming is 2713 1980, pole designation 410 sp 15, 6.0 meter long with cast iron base plate drilling of 1 dia hole on the upper portion of the pole for the installtion of street light and 1 dia hole on the lower portion of the pole for cableentry of the wire base pole paintng of red oxide and two coats of silver white aluminium paint. 221 sitc of 12mm thick frameless tempered clear glass ( toughened glass ) single door size: 1200mm x 2400mm with door spring and locking arrangements and both way handle and patch fittings. 222 single leaf non fire rated wooden door withvision panel 223 wooden door withvision panel 224 single leaf glass door with thin semi transparent film / laminate 225 glass door with 12 mm toughened glass, floor spring, arrangement for access control, handle, lock etc. complete 1000mm x2100mm 226 wooden door with locks 227 glass door toughened glass, floor spring, arrangement for access control, handle, lock etc 228 water motor pump ( 1.5 hp ) ( aqua group ) 229 overhead water tank ( capacity 5000 litre – 1 nos ) ( prince ) , ( capacity 500 litre – 4 nos ) ( nircon ) with sanitary and plumbing work...

Department Of Atomic Energy - Rajasthan

36174412 bids are invited for parker haniffin make o ring oil seals and rubber sheets 1 o ring item no. 01 parker make o ring of id 240.7 mm, thickness 3.53, material epr grade e 0740 75 for pss thimble ( upper ) side o ring ( part no. 3 / 25 ) . 2 o ring item no. 02 parker make o ring of id 186.0 mm, thickness 3.53 mm, material epr grade e0740 75 for pss thimble ( upper ) top face inner side o ring ( part no. 3 / 26 ) 3 o ring item no. 03 parker make o ring of id 226.0 mm, thickness 3.53 mm, material epr grade e0740 75 for pss thimble ( upper ) top face outer side o ring ( part no. 3 / 27 ) 4 o ring item no. 04 parker make o ring of id 231 mm, thickness 5.5 mm, material epr grade e 0740 75 for pss lower chamber side o ring ( part no. 3 / 28 ) 5 o ring item no. 05 parker make o ring of id 272.0 mm, thickness 3.53 mm, material epr grade e0740 75 for pss thimble ( upper ) to top sleeve o ring ( part no. 3 / 29 ) 6 o ring item no. 06 parker make o ring of id 128 mm, thickness 4 mm, material epr grade e 0740 75 for pss inspection window cover o ring. 7 o ring item no. 07 parker make o ring of id 149.0 mm, thickness 3.53 mm, material neoprene grade c 0557 70 for pss dash pot top cover and gear box top & bottom o ring. 8 o ring item no. 08 parker make o ring of id 35.0 mm, thickness 3.53 mm, material epr grade e 0740 75 for pss dash pot mechanical seal rotary face o ring. 9 o ring item no. 09 parker make o ring of id 40.5 mm x 3.53 mm cross section, material epr grade e0740 75 for pss dash pot mechanical seal stationary face. 10 o ring item no. 10 parker make o ring of id 133.8 mm x 3.50 mm cross sectional for 1” valvetek actuator ugp. material epr grade e 0740 75. 11 o ring item no. 11 parker make o ring of id 25 mm x 3.6 mm cross sectional for 1” valvetek actuator ugp. material epr grade e 0740 75. 12 o ring item no. 12 parker make o ring of id 14.4mm x 2mm cross sectional for 1” valvetek actuator ugp. material epr grade e 0740 75. 13 circular ring item no. 13 parker make circular ring of od 31.6 mm x id 19.2mm x 1.80mm thickness for 1” valvetek actuator ugp. material epr grade e 0740 75. 14 circular ring item no. 14 parker make circular ring of od 41.10 x 35 mm id x 1mm thickness for pss dash pot mechanical seal teflon washer. material ptfe. 15 oil seal item no. 15 parker make oil seal with garter spring, size 30x48x8 mm with garter spring for agms blower size. moc neoprene c0557 70 16 oil seal item no. 16 parker make o ring 169 mm x 3.5 mm for mal vacuum pump side cover. moc nbr ( n0674 70 ) 17 oil seal item no. 17 parker make o ring 10 mm x 3.5 mm for agms rv c / s. material neoprene ( c0557 70 ) 18 oil seal item no. 18 parker make oil seal with garter spring, size 35x52x10 mm for rab sump pump. material nbr ( n0674 70 ) 19 oil seal item no. 19 parker make o rings id 59.6 x 3.53 mm for bellow seal of regulating drive for adjuster drive, material neoprene c0557 70. 20 oil seal item no. 20 parker make o rings id 28.4 x 3.60 mm for mating ring of regulating drive for adjuster drive, material neoprene c0557 70 21 oil seal item no. 21 parker make oil seal with garter spring, size 22x32x7 mm for 7921 p 005&006 and 34932 p 12 / 13 / 14, material nbr ( n0674 70 ) 22 rubber sheet item no. 22 parker make pre oxide cured epdm rubber sheet as per epr ( e0740 75 ) rating of size 1000 mm x 1200 mm x 1.0 mm thick. shore hardness of the sheet should be 70 a + / 5 a throughout the length. sheets must be packed in proper cover for protection from uv. 23 rubber sheet item no. 23 parker make pre oxide cured epdm rubber sheet as per epr ( e0740 75 ) rating of size 1000 mm x 1200 mm x 1.5 mm thick. shore hardness of the sheet should be 70 a + / 5 a throughout the length. sheets must be packed in proper cover for protection from uv. 24 rubber sheet item no. 24 parker make pre oxide cured epdm rubber sheet as per epr ( e0740 75 ) rating of size 1000 mm x 1200 mm x 2 mm thick. shore hardness of the sheet should be 70 a + / 5 a throughout the length. sheets must be packed in proper cover for protection from uv. 25 rubber sheet item no. 25 parker make pre oxide cured epdm rubber sheet as per epr ( e0740 75 ) rating of size 1000 mm x 1200 mm x 2.5 mm thick. shore hardness of the sheet should be 70 a + / 5 a throughout the length. sheets must be packed in proper cover for protection from uv. 26 rubber sheet item no. 26 parker make pre oxide cured epdm rubber sheet as per epr ( e0740 75 ) rating of size 1000 mm x 1200 mm x 3 mm thick. shore hardness of the sheet should be 70 a + / 5 a throughout the length. sheets must be packed in proper cover for protection from uv. 27 rubber gasket item no. 27 parker make neoprene rubber gasket of size 445 ( od ) x385 ( id ) x3 ( thickness ) . shore hardness of the sheet should be 70 a + / 3 a throughout the length. sheets must be packed in proper cover for protection from uv. ( required for ugp manhole cover ) . physical properties test of neoprene as per c0557 70 rating 28 rubber gasket item no. 28 parker make neoprene rubber gasket of size 85.5 ( od ) x70 ( id ) x1.5 ( thickness ) . shore hardness of the gasket should be 70 a + / 3 a throughout the length. ( required for ugp distributor ) . physical properties test of neoprene as per c0557 70 rating. 29 o ring item no. 29 parker make o ring of id 55.5 mm, thickness 3.53 mm, material epdm e0740 75 for pss lower chamber cover. 30 o ring item no. 30 parker make o ring of id 230 mm, thickness 3 mm, material epdm e0740 75 for pss lower chamber cover. 31 o ring item no. 31 parker make o ring of id 14 mm, thickness 2.62 mm, material epdm e0740 75 for lpis actuator o ring. 32 o ring item no. 32 parker make o ring of id 128 mm, thickness 4.5 mm, material epdm e0740 75 for pss inspection window cover o ring. 33 rubber sheet item no. 33 parker make neoprene rubber sheet of rating c0557 70 and size 1000 mm x 1000 mm x 5 mm thick. shore hardness of the sheet should be 70 a + / 3 a throughout the length. sheets must be packed in proper cover for protection from uv. 34 o ring item no. 34 parker make o ring of id 38 mm, thickness 3.53 moc fkm ( v0747 75 ) , for agms mechanical seal. 35 o ring item no. 35 parker make o ring of id 30 mm, thickness 3.53 moc fkm ( v0747 75 ) , for agms mechanical seal. 36 o ring item no. 36 parker make o ring of id 47 mm, thickness 3.53 moc fkm ( v0747 75 ) , for agms mechanical seal. 37 cup seal item no. 37 parker make cup seal of id 50 mm, od 73.5 mm ( dimension 64x73.5 / 50x11.5 mm ) moc neoprene c0557 70 , for agms valve. 38 rectangular ring item no. 38 parker make neoprene material , rectangular ring of id 82 mm, od 88 mm and cross section of 3x2.5 mm.moc neoprene c0557 70 , for agms ball valve. 39 rectangular ring item no. 39 parker make , rectangular ring of id 14.5 mm, od 20 mm and crosssection of 2.75x2.5 mm. moc ptfe , for agms ball valve. 40 rectangular ring item no. 40 parker make , rectangular ring of id 14.5 mm, od 20 mm and crosssection of 2.75x0.8 mm. moc ptfe , for agms ball valve. 41 o ring item no. 41 parker make o ring for part no. 45 ( pilot area ) as per sss sv 50nb drawing. ( size 2.90 x 1.78 mm ) . moc epr grade e 0740 75. 42 o ring item no. 42 parker make o ring of size 37.8 x 2.62 mm, moc epr grade e 0740 75. part no. 34 ( main disc area ) as per sss sv 50nb drawing. 43 o ring item no. 43 parker make o ring of size 47.35 x 1.78 mm, moc epr grade e 0740 75. part no. 50 ( between guide and body ) as per sss sv 50nb drawing. 44 o ring item no. 44 parker make o ring of size 63.17 x 2.62 mm, moc epr grade e 0740 75. part no. 17 ( bonnet sealing area ) as per sss sv 50nb drawing. 45 o ring item no. 45 parker make o ring of size 4.47 x 1.78 mm, moc epr grade e 0740 75. part no. 34 ( main disc area ) as per sss sv 15nb drawing. 46 o ring item no. 46 parker make o ring of size 28.24 x 2.62 mm, moc epr grade e 0740 75. part no. 39 ( bonnet sealing area ) as per sss sv 15nb drawing. 47 o ring item no. 47 parker make o ring of size 24.99 x 3.53 mm, moc epr grade e 0740 75. for barcis drive tube o ring. 48 o ring item no. 48 parker make o ring of size 29.1 x 2.5 mm, moc epdm grade e 0740 75. for agms actuator bottom side. 49 o ring item no. 49 parker make o ring of size 15.5 x 2.62 mm, moc epdm grade e 0740 75. for agms actuator top side. 50 rectangular ring item no. 50 parker make rectangular ring of id 67 mm, od 76.4 mm and crosssection of 6 mm x 4.7 mm. moc epdm grade e 0740 75. for agms actuator. 51 o ring item no. 51 parker make o ring size 8 x 2mm for sss rv material epr e0740 75 52 oil seal item no. 52 parker make oil seal with garter spring of material nbr n0674 70, dimension11.7x28x6 mm ( adj.gear box ) with stiffener ring of 0.5 mm thick. 53 o ring item no. 53 parker make o ring of id 38.01 mm, thickness 2.5 moc nbr n0674 70, for adjuster gear box ( item no 7 / 76 ) . 54 o ring item no. 54 parker make o ring of id 37.8 mm, thickness 2.5 moc nbr n0674 70 , for adjuster gear box ( item no 7 / 77 ) . 55 o ring item no. 55 parker make o ring of id 48.2 mm, thickness 3.5 moc nbr n0674 70 , for adjuster gear box ( item no 7 / 78 ) . 56 o ring item no. 56 rcm drive motor unit parker make o ring part number 7 / 79 id 59.2 mm cross section 3.5mm moc nbr n0674 70 57 o ring item no. 57 rcm drive motor unit parker make o ring part number 7 / 80 id 78.6 mm cross section 3.5mm moc nbr n0674 70 58 o ring item no. 58 rcm drive motor unit parker make o ring part number 7 / 81 id 82.5 mm cross section 3.5mm moc nbr n0674 70 59 o ring item no. 59 rcm drive motor unit parker make o ring part number 7 / 82 id 124mm cross section 3.5mm moc nbr n0674 70 60 o ring item no. 60 rcm drive parker make o ring id 149.5mm cross section 3.5mm moc nbr n0674 70 61 o ring item no. 61 rcm drive ( item no.8 / 7 ) parker make o ring id 275mm cross section 3.5mm mocnbr n0674 70 62 o ring item no. 62 rcm drive ( item number 8 / 8 ) parker make o ring id 182mm cross section 3.5mm moc nbr, n0674 70 63 o ring item no. 63 rcm drive ( item number 8 / 9 ) o ring id 147mm cross section 3.5mm moc nbr n0674 70 64 o ring item no. 64 mal middle door spindle parker make o ring id 29.5 cross section 3.5 moc nbr n0674 70 65 oil seal item no. 65 parker make oil seal with garter spring of moc nbr n0674 70, dimension 40x55x5 mm ( ugp process water circulating pump ) 66 oil seal item no. 66 parker make oil seal with garter spring of moc nbr n0674 70, dimension 45x55x5 mm ( ugp process water filling pump ) 67 oil seal item no. 67 parker make oil seal with garter spring of moc nbr n0674 70, dimension 12x30x8 mm ( ugp chilled water booster pump ) 68 cup seal item no. 68 parker make cup seal 38x26x7 mm for mal actuator seal, moc nbr n0674 70 69 o ring item no. 69 parker make o ring for part no. 45 ( pilot area ) as per sss sv 50nb drawing. ( size 2.57 x 1.78 mm ) . moc epr grade e 0740 75. 70 o ring item no. 70 parker make o ring of size 36.17 x 2.62 mm, moc epr grade e 0740 75. part no. 34 ( main disc area ) as per sss sv 50nb drawing 71 o ring item no. 71 parker make pss lower chamber ‘o’ ring 20x4 mm moc epr grade e 0740 75. 72 oil seal item no. 72 parker make oil seal 65 x48x10 mm. moc nbr n0674 70, for 3493 1 p 4. 73 oil seal item no. 73 parker make oil seal 72x30x8 mm for upg p 12, 13, 14. moc nbr ( n0674 70 ) . 74 oil seal item no. 74 parker make oil seal 47x28x10 mm mal vacuum pump. moc nbr 75 oil seal item no. 75 parker make oil seal with garter spring, size 32x22x5 mm for 7921 p 005&006 and 34932 p 12 / 13 / 14.moc nbr ( n0674 70 ) . 76 oil seal item no. 76 parker make oil seal 65x45x8 mal rb side personal door. moc nbr n0674 70 77 oil seal item no. 77 parker make oil seal 72x35x12, 3493 0 p 7&8 moc nbr n0674 70 78 cup seal item no. 78 parker make cup seal 28x20x6 mm for eal actuator seal. moc nbr n0674 70 79 o ring item no. 79 parker make pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes 1.6 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 80 o ring item no. 80 parker make pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes 2.4 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv 81 o ring item no. 81 parker make pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes 3.2 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 82 o ring item no. 82 pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes4.8 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 83 o ring item no. 83 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 1.6 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv 84 o ring item no. 84 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 3.2 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv 85 o ring item no. 85 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 4.8 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv 86 o ring item no. 86 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 5.7 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 87 o ring item no. 87 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 6.4 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv 88 o ring item no. 88 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 8.4 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv 89 o ring item no. 89 parker make pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes 5.7 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 90 o ring item no. 90 parker make pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes 6.4 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 91 o ring item no. 91 parker make pre oxide cured o ring kit of epdm material epr grade e 0740 75 of following sizes 8.4 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv. 92 oil seal item no. 92 parker make oil seal with garter spring, size 39.5x50.05x7.5 mm for motor unit for gear box of pinion lower side upper seal with stiffener ring of 0.5 mm thick. mocnbr n0674 70 93 oil seal item no. 93 parker make oil seal with garter spring, size 24.5x44.5x5.5 mm for motor unit for gear box of pinion lower side lower seal with stiffener ring of 0.5 mm thick material nbr ( n0674 70 ) 94 o ring item no. 94 parker make pre oxide cured o ring kit of neoprene material c 0557 70 of following sizes 2.4 mm. shore hardness of the cord should be 70 a + / 5 a throughout the length. cords must be packed in proper cover for protection from uv...

Department Of Atomic Energy - Rajasthan

35182065 bids are invited for mechanical seal for primary circulating pump supply of eagle burgmann germany make complete mechanical seal for primary circulating pump of ksb make and model rsr 350 total quantity : 6...

Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

34273431 requirement of spare parts of m / s tianjin maindland hydrogen equipment co.ltd. make 2x10nm3 / hr hydrogen generation plant installed at ctpp, chhabra requirement of spare parts of m / s tianjin maindland hydrogen equipment co.ltd. make 2x10nm3 / hr hydrogen generation plant installed at ctpp, chhabra , lye cooler , lye strainer , catalyst gas cooler , dryer gas cooler , cooling water pump specifications. 2.2kw / 3.0hp, 2850rpm, 3 phase, 415v, 5.6amp, head 12 / 26m , water chiller ( water circulating pump ) specifications: type: smc 128, sr. no. a0fdfc2160, 2.5kw, 2700rpm, 3 phase, 415v, head 12 / 23m, size 50x40, impeller dia 154mm , cooling tower fan motor frame size; sev 112m, 2.2kw, 415v, 3 phase, 4.2 amp, 925rpm, eff. 81.8 power factor 0.09 , water level sensor. one no, one nc auxi supply 230v ac , temperature sensor.. ( for water chiller ) , rtd.300 mm. 24vdc. output signal.4 20mamp.0 500*c , rtd.125mm. 24vdc. output signal. 4 20mamp.0 500 *c , rtd.75mm. 24vdc. output signal.4 20mamp. 0 500*c , molecular sieve ( dryer chemical ) , palladium ( catalyst chemical ) , contactors: aux. supply 230v ac, no of pole 04, no of contacts 04, current carrying capacity >20amp , thermowell length: 900mm, dia: 6mm , dryer heater 1 phase, length 900mm, dia 6mm, 230v, 1000w , solenoid valve, rotex ( 24v dc 8w ) , cylinder filling hose pipe , lye making pumps 1.1kw , magnetic capsules for level separator ( 1set = 2nos. ) ...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

34266244 requirement of spare parts of m / s tianjin maindland hydrogen equipment co.ltd. make 2x10nm3 / hr hydrogen generation plant installed at ctpp, chhabra 1 lye cooler 4 nos. 2 lye strainer 4 nos. 3 catalyst gas cooler 2 nos. 4 dryer gas cooler 4 nos. 5 cooling water pump specifications. 2.2kw / 3.0hp, 2850rpm, 3 phase, 415v, 5.6amp, head 12 / 26m 2 nos. 6 water chiller ( water circulating pump ) specifications: type: smc 128, sr. no. a0fdfc2160, 2.5kw, 2700rpm, 3 phase, 415v, head12 / 23m, size 50x40, impeller dia 154mm 2 nos. 7 cooling tower fan motor frame size; sev 112m, 2.2kw, 415v, 3 phase, 4.2 amp, 925rpm, eff. 81.8 power factor 0.09 2 nos. 8 water level sensor. one no, one nc auxi supply 230v ac 2 set. 9 temperature sensor.. ( for water chiller ) 2 set. 10 rtd. 300 mm. 24vdc. output signal. 4 20mamp. 0 500*c 6 nos. 11 rtd. 125mm. 24vdc. output signal. 4 20mamp. 0 500 *c 6 nos. 12 rtd. 75mm. 24vdc. output signal. 4 20mamp. 0 500*c 4 nos. 13 molecular sieve ( dryer chemical ) 40 kg 14 palladium ( catalyst chemical ) 20 kg 15 contactors: aux. supply 230v ac, no of pole 04, no of contacts 04, current carrying capacity >20amp 4 nos. 16 thermowell length: 900mm, dia: 6mm 5 nos. 17 dryer heater 1 phase, length 900mm, dia 6mm, 230v, 1000w 6 nos. 18 solenoid valve, rotex ( 24v dc 8w ) 20 nos. 19 cylinder filling hose pipe 12 nos. 20 lye making pumps 1.1kw 1 no. 21 magnetic capsules for level separator ( 1set = 2nos. ) ...

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

29954320 supply & fixing of new equipments and repair modification of existing equipment at central laboratory rsrdc ltd. head office jaipur 1 part a: new equipments 0.0001 each 0.00 0.00 inr only 2 supply and fixing of compression testing machine at central labortory rsrdc ltd. head office jaipur. machine must be as per nabl guidlines and suitable for the compressive strength test for concrete cube/cylinder as per is 516/astm c 39 (2000 kn) with flexure testing attechment of 100 kn. the calibration certificate required from nabl accredition agency after installation at site. make aimil or epuipment system should have following features: compression testing machine must be controlled by an intelligent pace rate controller it should facilitate automatic pace rate controlat a preset value full 3 term pid feed back control which uses a high torque stepper motor it should consist of loading unit, an electrically operated hydraulic pump and intelligent pace rate controller pace deviation bar graph automatic stress determination and display overload safety protection self aligning platen with fast accessory change capability configurable engineering unit for machine selection predefined machine capacities for each engineering unit. specific capacity can be selected from the drop down menu 0.0001 each 0.00 0.00 inr only price schedule schedule g (this boq template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. bidders are allowed to enter the bidder name and values only ) percentage boq tender inviting authority: gm rsrdc ltd jaipur name of work : supply and fixing of new equipment and repair modification of existing equipment at central laboratory rsrdc ltd., head office , jaipur contract no: 221/21 22 validate print help predefined machine capacities for each engineering unit. specific capacity can be selected from the drop down menu flexible calibration points. calibration can be done on 5 to 10 points peak load, peak stress, unique record no. display edi with provision to configure more than one mode dynamic calibration user can set break point data download through usb in ascii format data storage upto 2000 records peak stress calculation based on sample type and shape controller must incorporate a four line digital display and features the integral load pacing bar display, maximum load and stress result display, parallel port output and usb output start, stop, pause & reset facility password protection for system & calibration setup 3 system should have following technical specifications : the accuracy of the testing machine shall be such that the percentage of error for the loads within the proposed range of use of the testing machine shall not exceed ±1.0 percent of the indicated load the machine should have 2% overload facility to calibrate the machine upto full capacity loading unit : should be welded construction type with cross head, base and side plates (solid), hydraulic jack at base, upper platens should be with self aligning facility, should be supplied with spacers. pressure transducers should be calibrated in kn & a calibration certificate from nabl must be provided at the time of installation at site. capacity : 2000 kn oil seal must be teflon paint should be powder coated spacers should be provided for adjustment of the test height of sample maximum clearance between upper and lower platens : 370mm maximum distance between side platens : 340mm platen size : 222 dia (mm) piston diameter : 222.2 dia (mm) piston stroke : 50mm specimen to be tested 100mm & 150mm cube, 100mm & 150mm dia cylinder least count (resolution) of load measuring device : 0.1 kn pumping unit : motor (around 0.5 hp, single phase, 220 v ac supply) driven 2 speed hydraulic pump and bonded strain gauge based pressure transdu suitable for operation on 220v/230v, single phase, 50 hz, ac supply 0.0001 each 0.00 0.00 inr only 4 unit price total including gst & 1 year guarantee/warranty= 5 supply and instulation of asphalt contant tester irc accredited. this machine is used to determine the asphalt content of hot mix asphalt (hma) asphalt content tester this machine is used to determine the asphalt content of hot mix asphalt (hma) paving mixtures and pavement samples by removing the asphalt is an ignition furanace by means of sample heating not by means of solvents. suitable for operation on 415v, 50hz, 20a, 3phase, ac supply. the calibration certificate required from nabl accredition agency . make aimil or epuipment system should have following technical specifications: working temperature : 540±2°c combustion temperature : 750°c balance capacity useble : 10kg accuracy of electronic balance : 0.1g balance capacity useable : 2500g recommended weight of sample : 1500g time for test results : 30 to 45min end point sensitivity : 0.01%for 3 consecutive minutes data output : through sd card chamber size : 300mm*340mm*400mm outer size : 590mm*755mm*1300mm power rating : 5kw accessories : sample bucket 2sets, safety cover for bucket 1no., lifting handle 1no., asbestos gloves 1no., safety helmet – 1no. 0.0001 each 0.00 0.00 inr only 6 unit price total including gst & 1 year guarantee/warranty= 1 no. 973500.00 973500.00 inr nine lakh seventy three thousand five hundred only 7 supply and instulation of curing tank for concrete cube/cylindring, mortar cubes sample with top cover hinged lid (ss). the calibration certificate required from nabl accredition agency after installation at site. technical specification of machine. a) size 24moulds of 150mm dia can be fit b) material inside: stainless steel 304 grade, 18gauge sheet c) material outside: 18gauge sheet d) temperature range: 20 deg cel to 40 degree cel , lc 0.1degree celsiuse working range: 27±2 degree celsius e) operated on : 230v, 50hz , single phase, ac supply f) heater capacity: 3.0kw of make: red hot g) water circulating pump precision or eqavalent h) compliance standards: (is: 9013 1978) i) make aimil, a sky instruments or epuipment 0.0001 each 0.00 0.00 inr only system should have following features: itmust be fully insulated, with thermostat and recirculation pump. drain valves and electrical equipment should be housed in a compartment located at one end of the tank. 8 unit price total including gst & 1 year guarantee/warranty= 1 no. 292404.00 292404.00 inr two lakh ninety two thousand four hundred & four only 9 supply of digital hot air oven with the calibration certificate required from nabl accredition agency after installation at site. make aimil, a sky instruments or equivalent range ambient temp to 300deg cel lc 0.1deg cel material: inner ss 304grade outer : ms 18gauge sheet size of oven inner: 24x24x24 inches (lxwxh) temperature controller: digital pid controller air circulation: mode of hot air circulation impeller located at a strategic position where from where uniform air circulation is ahieved). tray : 2nos insulation: glass wool. door: single insulated door with steel lock with handle. paint: powder coating. power: 230v ac, 50 hz. 0.0001 each 0.00 0.00 inr only 10 unit price total including gst & 1 year guarantee/warranty= 1 no. 76700.00 76700.00 inr seventy six thousand seven hundred only 11 supply of digital vernier caliper with the calibration certificate required from nabl accredition agency . make insize , mitutoyo or equivalent range 300mm resolution: 0.01mm 0.0001 each 0.00 0.00 inr only 12 unit price total including gst & 1 year guarantee/warranty= 1 no. 11210.00 11210.00 inr eleven thousand two hundred & ten only 13 supply of digital outside micrometer/screw gauge with the calibration certificate required from nabl accredition agency . make insize , mitutoyo or equivalent range: 0 25mm resolution: 0.001mm 0.0001 each 0.00 0.00 inr only 14 unit price total including gst & 1 year guarantee/warranty= 1 no. 10030.00 10030.00 inr ten thousand &thirty only 15 supply of temperature rtd sensor , with digital temperature indicator for temperature measurement with the calibration certificate required from nabl accredition agency . make a sky instruments , tempsens , tipl or equivalent technical specification as below: (a) 3wire rtd sensor (length 300mm; and dia 6mm) & wire length of sensar 2mtr. (b) temperature range 0oc to 300oc (c) least count 0.1oc (d) data storage • high precision with 19999 counts standard probe: 50 ~ 250°c, alarm set and °c / °f convertible 0.0001 each 0.00 0.00 inr only 16 unit price total including gst & 1 year guarantee/warranty= 1 no. 9263.00 9263.00 inr nine thousand two hundred & sixty three only 17 supply of digital weighing balance with the calibration certificate required from nabl accredition agency at site . make axcel , wensar , mettler or equivalent range: 0 3kg , pan size 230x230mm resolution : 0.1gm rechargeable battery backup , red led, front display 0.0001 each 0.00 0.00 inr only 18 unit price total including gst & 1 year guarantee/warranty= 1 no. 14750.00 14750.00 inr fourteen thousand seven hundred & fifty only 19 supply of digital weighing balance with the calibration certificate required from nabl accredition agency at site . make axcel , wensar , mettler or equivalent range: 0 15kg , pan size 300x300mm resolution : 0.5gm rechargeable battery backup , red led, front display 0.0001 each 0.00 0.00 inr only 20 unit price total including gst & 1 year guarantee/warranty= 1 no. 19470.00 19470.00 inr nineteen thousand four hundred & seventy only 21 supply of temperature and humidity meter (thermohygrometer) with the calibration certificate required from nabl accredition agency . make htc, mextech ppi/metravi or equivalent technical specs of machine: temp range: 50 to +70 deg cel , resolution: 0.1deg cel humidity range: 10% to 99% rh resolution: 1% rh 2 modes for temperature showing: ⁰c or ⁰f 0.0001 each 0.00 0.00 inr only 22 unit price total including gst & 1 year guarantee/warranty= 1 no. 11800.00 11800.00 inr eleven thousand eight hundred only 23 supply of weight box (s.s.) with the calibration certificate required from nabl accredition agency . make: wensar , metller or equivalent class m1 , range 23pcs set from 1mg to 200g standard – oiml r111 material: 304 stainless steel shape: cylindrical with knob and wire weight finish: mirror polish packing: aluminum alloy box/wooden box. 0.0001 each 0.00 0.00 inr only 24 unit price total including gst & 1 year guarantee/warranty= 1 no. 17700.00 17700.00 inr seventeen thousand seven hundred only 25 supply of standard weight with the calibration certificate required from nabl accredition agency . make: wensar , metller or equivalent class m1 range 500g standard – oiml r111 0.0001 each 0.00 0.00 inr only material: 304 stainless steel shape: cylindrical with knob finish: mirror polish 26 unit price total including gst & 1 year guarantee/warranty= 1 no. 4720.00 4720.00 inr four thousand seven hundred & twenty only 27 supply of standard weight with the calibration certificate required from nabl accredition agency . make: wensar , metller or equivalent class m1 range 1kg standard – oiml r111 material: 304 stainless steel shape: cylindrical with knob finish: mirror polish 0.0001 each 0.00 0.00 inr only 28 unit price total including gst & 1 year guarantee/warranty= 1 no. 5664.00 5664.00 inr five thousand six hundred & sixty four only 29 supply of standard weight with the calibration certificate required from nabl accredition agency . make: wensar , metller or equivalent class m1 range 2kg standard – oiml r111 material: 304 stainless steel shape: cylindrical with knob finish: mirror polish 0.0001 each 0.00 0.00 inr only 30 unit price total including gst & 1 year guarantee/warranty= 1 no. 8850.00 8850.00 inr eight thousand eight hundred & fifty only 31 supply of standard weight with the calibration certificate required from nabl accredition agency . make: wensar , metller or equivalent class m1 range 5kg standard – oiml r111 material: 304 stainless steel shape: cylindrical with knob finish: mirror polish 0.0001 each 0.00 0.00 inr only 32 unit price total including gst & 1 year guarantee/warranty= 1 no. 14750.00 14750.00 inr fourteen thousand seven hundred & fifty only 33 supply of standard weight with the calibration certificate required from nabl accredition agency . make: wensar , metller or equivalent class m1 range 10kg standard – oiml r111 material: 304 stainless steel shape: cylindrical with knob finish: mirror polish 0.0001 each 0.00 0.00 inr only 34 unit price total including gst & 1 year guarantee/warranty= 1 no. 20650.00 20650.00 inr twenty thousand six hundred & fifty only 35 supply of roack & minerals test kit set of moh’s hardness scale make a sky instruments, controls, aimils or equivalent collection contains 9 minerals represents the scale of hardness talc (h=1), gypsum (h=2), calcite (h=3), fluorite (h=4), apatite (h=5) orthoclase (h=6), quartz (h=7), topaz (h=8) & corundum (h=9) diamond 0.0001 each 0.00 0.00 inr only 36 unit price total including gst & 1 year guarantee/warranty= 1 no. 17700.00 17700.00 inr seventeen thousand seven hundred only 37 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 80mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 38 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 39 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 75mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 40 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 41 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 53mm , diameter 450mm, gi sieve, perforated type 42 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 43 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 45mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 44 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 45 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 40mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 46 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 47 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 9.50mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 48 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 49 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 4.75mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 50 unit price total including gst & 1 year guarantee/warranty= 1 no. 2506.00 2506.00 inr two thousand five hundred & six only 51 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 2.36mm , diameter 450mm, gi sieve, perforated type 0.0001 each 0.00 0.00 inr only 52 unit price total including gst & 1 year guarantee/warranty= 2 no. 2506.00 5012.00 inr five thousand &twelve only 53 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 2.36mm , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 54 unit price total including gst & 1 year guarantee/warranty= 1 no. 3620.00 3620.00 inr three thousand six hundred & twenty only 55 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 1.18mm , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 56 unit price total including gst & 1 year guarantee/warranty= 2 no. 3620.00 7240.00 inr seven thousand two hundred & forty only 57 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 850micro , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 58 unit price total including gst & 1 year guarantee/warranty= 1 no. 3620.00 3620.00 inr three thousand six hundred & twenty only 59 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 600micro , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 60 unit price total including gst & 1 year guarantee/warranty= 1 no. 3620.00 3620.00 inr three thousand six hundred & twenty only 61 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 425micro , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 62 unit price total including gst & 1 year guarantee/warranty= 1 no. 3620.00 3620.00 inr three thousand six hundred & twenty only 63 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 150micro , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 64 unit price total including gst & 1 year guarantee/warranty= 1 no. 3620.00 3620.00 inr three thousand six hundred & twenty only 65 supply of test sieve, for gradation with the calibration certificate required from nabl accredition agency . make: a sky instruments , jayant, or equivalent range 75micro , diameter 200mm, brass sieve, perforated type 0.0001 each 0.00 0.00 inr only 66 unit price total including gst & 1 year guarantee/warranty= 2 no. 3620.00 7240.00 inr seven thousand two hundred & forty only 67 supply of heating cooling system for curring tank suitable for tank size approx : 200cm*75cm*60cm* fitted with digital temperature controller with sensor(make:ppi/multispan or other eqvilent brand), with heating and colling system to maintain temperature 27+2oc, temperature range: 25 to 30oc, least count 0.1oc, and pump for water circulation (make:kirloshkar/crompton/goderaj or other eqvilent brand), to maintain proper & unifrom temperature providing s.s. 304 grade 18 gauge hinged top lid in two parts. also required calibration certificate from nabl accredited agency at site. 0.0001 each 0.00 0.00 inr only 68 unit price total including gst & 1 year guarantee/warranty= 1 no. 188800.00 188800.00 inr one lakh eighty eight thousand eight hundred only 69 part b: comprehensive maintenace charges (second year) 0.0001 each 0.00 0.00 inr only 70 add extra for comprehensive maintenance charges inculding repalacment of damaged parts & nabl calibration certificate of each from nabl accreditation agency @ 10 % + 18% gst (as applicable) per year. for second year (first year to second year) 0.0001 each 0.00 0.00 inr only 71 unit cmc price for one year 1 no. 299460.00 299460.00 inr two lakh ninety nine thousand four hundred & sixty only 72 part c: comprehensive maintenace charges (thrid year) 0.0001 each 0.00 0.00 inr only 73 add extra for comprehensive maintenance charges inculding repalacment of damaged parts & nabl calibration certificate of each from nabl accreditation agency @ 10 % + 18% gst (as applicable) per year. for second year ( second year to thrid year) 0.0001 each 0.00 0.00 inr only 74 unit cmc price for one year 1 no. 299460.00 299460.00 inr two lakh ninety nine thousand four hundred & sixty only 75 part d repair / modification of existing lab equipments 0.0001 each 0.00 0.00 inr only 76 supply and fixing of mild steel jali arrangment for safty of comprassive testing machine of 1000kn. including painting at site. 0.0001 each 0.00 0.00 inr only 77 unit price total including gst & 1 year guarantee/warranty= 1 no. 3540.00 3540.00 inr three thousand five hundred & forty only 78 digital conversion of existing oven work, fitting of digital temperature contraller, rtd sensor 300mm long, 6mm dia, temperature range ambient to 300oc, least count 0.1oc, relay, switch and indicatr etc. complete. also required calibration certificate from nabl accredited agency at site. . 79 unit price total including gst & 1 year guarantee/warranty= 1 no. 10620.00 10620.00 inr ten thousand six hundred & twenty only 80 repair including service of penetrometar (wbm/gsb test) 0.0001 each 0.00 0.00 inr only 81 unit price total including gst & 1 year guarantee/warranty= 1 no. 8260.00 8260.00 inr eight thousand two hundred & sixty only 82 repair of aiv make impact testing machine with providing and fixing of counter mater suaitable for aiv 0.0001 each 0.00 0.00 inr only 83 unit price total including gst & 1 year guarantee/warranty= 1 no. 1180.00 1180.00 inr one thousand one hundred & eighty only 84 required calibratin certificate from nabl accredited agency for follow each sieves. gi sieves, 450mm dia. range 80mm, 75mm, 63mm, 63mm, 53mm, 45mm, 40mm, 37.50mm, 37.50mm, 22.40mm, 22.40mm, 20mm, 20mm, 19mm, 19mm, 13.20mm, 13.20mm, 12.50mm, 12.50mm, 11.20mm, 11.20mm, 10mm, 10mm, 9.50mm & 4.75mm 0.0001 each 0.00 0.00 inr only 85 unit price total including gst & 1 year guarantee/warranty= 25 no. 1180.00 29500.00 inr twenty nine thousand five hundred only 86 required calibratin certificate from nabl accredited agency for follow each sieves. brass sieves, 200mm dia. range 2.36mm, 850micro, 600micro, 425micro, 300micro, 300micro & 150 micro 0.0001 each 0.00 0.00 inr only 87 unit price total including gst & 1 year guarantee/warranty= 7 no. 1180.00 8260.00 inr eight thousand two hundred & sixty only 88 repair and service bitumen extractor machine (aimil make). also required calibration certificate from nabl accredited agency at site. 0.0001 each 0.00 0.00 inr only 89 unit price total including gst & 1 year guarantee/warranty= 1 no. 7080.00 7080.00 inr seven thousand &eighty only 90 supply of chemical solvent trichloroethylene for bitumen extraction test 0.0001 each 0.00 0.00 inr only 91 unit price total including gst & 1 year guarantee/warranty= ...

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

29944082 supply and fixing of new equipment and repair modification of existing equipment at central laborary, rsrdc ltd. head office, jaipur supply and fixing of compression testing machine at central labortory rsrdc ltd. head office jaipur. machine must be as per nabl guidlines and suitable for the compressive strength test for concrete cube/cylinder as per is 516/astm c 39 (2000 kn) with flexure testing attechment of100 kn. thecalibration certificate required from nabl accreditionagency afterinstallationat site.make aimil or epuipmentsystem should have following features: compression testing machine must be controlled by an intelligent pace rate controllerit should facilitate automatic pace rate controlat a preset value full 3 term pid feed back control which uses a high torque stepper motor it should consist of loading unit, an electrically operated hydraulic pump and intelligent pace rate controller pace deviation bar graph automatic stress determination and display overload safety protection self aligning platen with fast accessory change capability configurable engineering unit for machine selection predefined machine capacities for each engineering unit. specific capacity can be selected from the drop down menu flexible calibration points. calibration can be done on 5 to 10 points peak load, peak stress, unique record no. display edi with provision to configure more than one mode dynamic calibration user can set break point data download through usb in ascii format data storage upto 2000 records peak stress calculation based on sample type and shape controller must incorporate a four line digital display and features the integral load pacing bar display, maximum load and stress result display, parallel port output and usb output start, stop, pause & reset facility password protection for system & calibration setup 3 system should have following technical specifications : the accuracy of the testing machine shall be such that the percentage of error for the loads within the proposed range of use of the testing machine shall not exceed ±1.0 percent of the indicated load the machine should have 2% overload facility to calibrate the machine upto full capacity loading unit : should be welded construction type with cross head, base and side plates (solid), hydraulic jack at base, upper platens should be with self aligning facility, should be supplied with spacers. pressure transducers should be calibrated in kn & a calibration certificate from nabl must be provided at the time of installation atsite. capacity : 2000 kn oil seal must be teflon paint should be powder coated spacers should be provided for adjustment of the test height of sample maximum clearance between upper and lower platens : 370mm maximum distance between side platens : 340mm platen size : 222 dia (mm) piston diameter : 222.2 dia (mm) piston stroke : 50mm specimen to be tested 100mm & 150mm cube, 100mm & 150mm dia cylinder least count (resolution) of load measuring device : 0.1 kn pumping unit : motor (around 0.5 hp, single phase, 220 v ac supply) driven 2 speed hydraulic pump and bonded strain gauge based pressure transdu suitable for operation on 220v/230v, single phase, 50 hz, ac supply 4 unit price total including gst & 1 year guarantee/warranty= 5 supply and instulation of asphalt contant tester irc accredited. this machine is used to determine the asphalt content of hot mix asphalt (hma)asphalt content testerthis machine is used to determine the asphalt content of hot mix asphalt (hma) paving mixtures and pavement samples by removing the asphalt is an ignition furanace by means of sample heating not by means of solvents.suitable for operation on 415v, 50hz, 20a, 3phase, ac supply.thecalibration certificate required from nabl accreditionagency .make aimil or epuipmentsystem should have following technical specifications:working temperature:540±2°ccombustion temperature :750°cbalance capacity useble : 10kgaccuracy of electronic balance: 0.1gbalance capacity useable : 2500grecommended weight of sample: 1500gtime for test results :30 to 45minend point sensitivity : 0.01%for 3 consecutive minutesdata output : through sd cardchamber size:300mm*340mm*400mmouter size :590mm*755mm*1300mmpower rating : 5kwaccessories :sample bucket 2sets,safety cover for bucket 1no.,lifting handle 1no., asbestos gloves 1no., safety helmet – 1no. 6 unit price total including gst & 1 year guarantee/warranty= 7 supply and instulation of curing tank for concrete cube/cylindring, mortar cubes sample with top cover hinged lid (ss). the calibration certificate required from nabl accreditionagency afterinstallationat site.technical specification of machine.a) size 24moulds of 150mm dia can be fitb) material inside: stainless steel 304 grade, 18gauge sheetc) material outside: 18gauge sheetd) temperature range: 20 deg cel to 40 degree cel , lc 0.1degree celsiuse working range: 27±2 degree celsiuse) operated on : 230v, 50hz , single phase, ac supplyf) heater capacity: 3.0kw of make: red hotg) water circulating pump precision or eqavalent h) compliance standards: (is: 9013 1978)i) make aimil, a sky instruments or epuipmentsystem should have following features:itmust be fully insulated, with thermostat and recirculation pump. drain valves and electrical equipment should be housed in a compartment located at one end of the tank. 8 unit price total including gst & 1 year guarantee/warranty= 9 supply ofdigital hot air oven with thecalibration certificate required from nabl accreditionagency afterinstallationat site.make aimil, a sky instruments or equivalentrange ambient temp to 300deg cel lc 0.1deg celmaterial: inner ss 304gradeouter : ms 18gauge sheetsize of oven inner: 24x24x24 inches (lxwxh)temperature controller: digital pid controllerair circulation: mode of hot air circulation impeller located at a strategic position where from where uniform air circulation is ahieved).tray : 2nosinsulation: glass wool.door: single insulated door with steel lock with handle.paint: powder coating. power: 230v ac, 50 hz. 10 unit price total including gst & 1 year guarantee/warranty= 11 supply ofdigital vernier caliper withthecalibration certificate required from nabl accreditionagency .make insize , mitutoyo or equivalentrange 300mmresolution: 0.01mm 12 unit price total including gst & 1 year guarantee/warranty= 13 supply ofdigital outside micrometer/screw gauge with thecalibration certificate required from nabl accreditionagency .make insize , mitutoyo or equivalentrange: 0 25mmresolution: 0.001mm 14 unit price total including gst & 1 year guarantee/warranty= 15 supply of temperature rtd sensor , with digital temperature indicator for temperature measurement with thecalibration certificate required from nabl accreditionagency .make a sky instruments , tempsens , tipl or equivalenttechnical specification as below: (a) 3wire rtd sensor (length 300mm; and dia 6mm) & wire length of sensar 2mtr.(b) temperature range 0oc to 300oc(c) least count 0.1oc(d) data storage • high precision with 19999 counts standard probe: 50 ~ 250°c, alarm set and °c / °f convertible 16 unit price total including gst & 1 year guarantee/warranty= 17 supply ofdigital weighing balance with the calibration certificate required from nabl accreditionagency at site .make axcel , wensar , mettler or equivalentrange: 0 3kg , pan size 230x230mmresolution : 0.1gmrechargeable battery backup , red led, front display 18 unit price total including gst & 1 year guarantee/warranty= 19 supply ofdigital weighing balance withthe calibration certificate required from nabl accreditionagency at site .make axcel , wensar , mettler or equivalentrange: 0 15kg , pan size 300x300mmresolution : 0.5gmrechargeable battery backup , red led, front display 20 unit price total including gst & 1 year guarantee/warranty= 21 supply of temperature and humidity meter (thermohygrometer) with the calibration certificate required from nabl accreditionagency .make htc, mextech ppi/metravi or equivalenttechnical specs of machine: temp range: 50 to +70 deg cel , resolution: 0.1deg celhumidity range: 10% to 99% rh resolution: 1% rh2 modes for temperature showing: °c or °f 22 unit price total including gst & 1 year guarantee/warranty= 23 supply of weight box (s.s.) with the calibration certificate required from nabl accreditionagency .make: wensar , metller or equivalentclass m1 , range 23pcs set from 1mg to 200gstandard – oiml r111material: 304 stainless steelshape: cylindrical with knob and wire weightfinish: mirror polishpacking: aluminum alloy box/wooden box. 24 unit price total including gst & 1 year guarantee/warranty= 25 supply of standard weight with the calibration certificate required from nabl accreditionagency .make: wensar , metller or equivalentclass m1range 500gstandard – oiml r111material: 304 stainless steelshape: cylindrical with knobfinish: mirror polish 26 unit price total including gst & 1 year guarantee/warranty= 27 supply of standard weight with the calibration certificate required from nabl accreditionagency .make: wensar , metller or equivalentclass m1range 1kgstandard – oiml r111material: 304 stainless steelshape: cylindrical with knobfinish: mirror polish 28 unit price total including gst & 1 year guarantee/warranty= 29 supply ofstandard weight with the calibration certificate required from nabl accreditionagency .make: wensar , metller or equivalentclass m1range 2kgstandard – oiml r111material: 304 stainless steelshape: cylindrical with knobfinish: mirror polish 30 unit price total including gst & 1 year guarantee/warranty= 31 supply ofstandard weight with the calibration certificate required from nabl accreditionagency .make: wensar , metller or equivalentclass m1range 5kgstandard – oiml r111material: 304 stainless steelshape: cylindrical with knobfinish: mirror polish 32 unit price total including gst & 1 year guarantee/warranty= 33 supply ofstandard weight with the calibration certificate required from nabl accreditionagency .make: wensar , metller or equivalentclass m1range 10kgstandard – oiml r111material: 304 stainless steelshape: cylindrical with knobfinish: mirror polish 34 unit price total including gst & 1 year guarantee/warranty= 35 supply of roack & minerals test kit set of moh’s hardness scalemake a sky instruments, controls, aimils or equivalentcollection contains 9 minerals represents the scaleof hardness talc (h=1), gypsum (h=2), calcite (h=3), fluorite (h=4), apatite (h=5) orthoclase (h=6), quartz (h=7), topaz (h=8) & corundum (h=9) diamond 36 unit price total including gst & 1 year guarantee/warranty= 37 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 80mm , diameter 450mm, gi sieve, perforated type 38 unit price total including gst & 1 year guarantee/warranty= 39 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 75mm , diameter 450mm, gi sieve, perforated type 40 unit price total including gst & 1 year guarantee/warranty= 41 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 53mm , diameter 450mm, gi sieve, perforated type 42 unit price total including gst & 1 year guarantee/warranty= 43 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 45mm , diameter 450mm, gi sieve, perforated type 44 unit price total including gst & 1 year guarantee/warranty= 45 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 40mm , diameter 450mm, gi sieve, perforated type 46 unit price total including gst & 1 year guarantee/warranty= 47 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 9.50mm , diameter 450mm, gi sieve, perforated type 48 unit price total including gst & 1 year guarantee/warranty= 49 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 4.75mm , diameter 450mm, gi sieve, perforated type 50 unit price total including gst & 1 year guarantee/warranty= 51 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 2.36mm , diameter 450mm, gi sieve, perforated type 52 unit price total including gst & 1 year guarantee/warranty= 53 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 2.36mm , diameter 200mm, brass sieve, perforated type 54 unit price total including gst & 1 year guarantee/warranty= 55 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 1.18mm , diameter 200mm, brass sieve, perforated type 56 unit price total including gst & 1 year guarantee/warranty= 57 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 850micro , diameter 200mm, brass sieve, perforated type 58 unit price total including gst & 1 year guarantee/warranty= 59 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 600micro , diameter 200mm, brass sieve, perforated type 60 unit price total including gst & 1 year guarantee/warranty= 61 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 425micro , diameter 200mm, brass sieve, perforated type 62 unit price total including gst & 1 year guarantee/warranty= 63 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 150micro , diameter 200mm, brass sieve, perforated type 64 unit price total including gst & 1 year guarantee/warranty= 65 supply of test sieve, for gradation with the calibration certificate required from nabl accreditionagency .make: a sky instruments , jayant, or equivalentrange 75micro , diameter 200mm, brass sieve, perforated type 66 unit price total including gst & 1 year guarantee/warranty= 67 supply of heating cooling systemfor curring tank suitable for tank size approx : 200cm*75cm*60cm* fitted with digital temperature controller with sensor(make:ppi/multispan or other eqvilent brand), with heating and colling system to maintain temperature 27+2oc, temperature range: 25 to 30oc, least count 0.1oc, and pump for water circulation (make:kirloshkar/crompton/goderaj or other eqvilent brand), to maintain proper & unifrom temperatureproviding s.s. 304 grade 18 gauge hinged top lid in two parts. also required calibration certificate from nabl accredited agency at site. 68 unit price total including gst & 1 year guarantee/warranty= 69 part b: comprehensive maintenace charges (second year) 70 add extra for comprehensive maintenance charges inculding repalacment of damaged parts & nabl calibration certificate of each from nabl accreditation agency @ 10 % + 18% gst (as applicable) per year. for second year (first year to second year) 71 unit cmc price for one year 72 part c: comprehensive maintenace charges (thrid year) 73 add extra for comprehensive maintenance charges inculdingrepalacment of damaged parts & nabl calibration certificate of each from nabl accreditation agency @ 10 % + 18% gst (as applicable) per year. for second year ( second year to thrid year) 74 unit cmc price for one year 75 part d repair / modification of existing lab equipments 76 supply and fixing of mild steel jali arrangment for safty of comprassive testing machine of 1000kn. including painting at site. 77 unit price total including gst & 1 year guarantee/warranty= 78 digital conversion of existing oven work, fitting of digital temperature contraller, rtd sensor 300mm long, 6mm dia, temperature range ambient to 300oc, least count 0.1oc, relay, switch and indicatr etc. complete. also required calibration certificate from nabl accredited agency at site. . 79 unit price total including gst & 1 year guarantee/warranty= 80 repair including service of penetrometar (wbm/gsb test) 81 unit price total including gst & 1 year guarantee/warranty= 82 repair of aiv make impact testing machine with providing and fixing of counter mater suaitable for aiv 83 unit price total including gst & 1 year guarantee/warranty= 84 required calibratin certificate from nabl accredited agency for follow each sieves. gi sieves, 450mm dia. range 80mm, 75mm, 63mm, 63mm, 53mm, 45mm, 40mm, 37.50mm, 37.50mm, 22.40mm, 22.40mm, 20mm, 20mm, 19mm, 19mm, 13.20mm, 13.20mm, 12.50mm, 12.50mm, 11.20mm, 11.20mm, 10mm, 10mm, 9.50mm & 4.75mm 85 unit price total including gst & 1 year guarantee/warranty= 86 required calibratin certificate from nabl accredited agency for follow each sieves. brass sieves, 200mm dia. range 2.36mm, 850micro, 600micro, 425micro, 300micro, 300micro & 150 micro 87 unit price total including gst & 1 year guarantee/warranty= 88 repair and service bitumen extractor machine (aimil make). also required calibration certificate from nabl accredited agency at site. 89 unit price total including gst & 1 year guarantee/warranty= 90 supply of chemical solvent trichloroethylene for bitumen extraction test 91 unit price total including gst & 1 year guarantee/warranty= ...

Public Works Department - Rajasthan

29618922 replacement of water circulating pump and other accessories in 1st type bunglow and other bunglows at gandhi nagar, jaipur. 1 supply installation testing & commissioning of iso certified manufacturer madepressure boosting pump with 24 ltr. ms tank, pressure switch, pressure gauge, and all standard fittings fully automatic on / off system, 2900 rpm with stainless steel casing,& impellor suitable for following capacity complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 2 1.0 hp ( 25 15 ) mtr, (30 48 ) lpm 3 providing & fixing of iso certified company made beestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanas per pwd specification for electrical works, conform to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing (i.e. isi marking) or quality certification such as iso – 9001 or above , with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 4 1200 mm sweep bee 1 star rated (service value >=4.0 to <4. 5 ) 5 providing & fixing of capacitor start, copper wound, metal body, metal blade three speed wall mounting fan of following sweep with the help of anchor bolts including making connection testing etc. as required. oem shall be an iso certified company.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 6 400 mm sweep(oscillating type) 7 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. oem shall be an iso certified company.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 8 225 mm sweep 9 300 mm sweep 10 providing & fixing of heavy duty capacitor start, copper woinddouble ball bearing900/1400 rpm single phaseexhaustfan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 11 300 mm sweep(900/1400 rpm) 12 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, power consumption of18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 13 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr. 14 4 led tube shape fixture 18/20 w (polycarbonate base) 15 providing & fixing of ip20 led recessed / surface mounted, round / sqaure non dimmable back lit smd mid power led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal/ external bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and in compliance to iec standards. system lumen efficacy min. 100 lm/watt, thd < 10 % ,p.f.=0.95, cri >80,life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing onhousing. oemmust have its own in house nabl acredeated lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr. 16 surface mounting 17 led downlight 18/20w 18 providing & fixing of ik07 ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum lm6/ adc12 material with heat dissipation fins on housing with uv stabilized pc/toughened glass cover (uv stablzation report submitted for uv cover ) and secondary lens on each led & should be smd type . the system level luminaire efficacy >=120 lm/ wtwith high power leds is to be usedand potted driver must be potted & has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety ,input frequency 50hz±3% power factor >0.95 driverefficiency >85%,thd(i) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <1000ma shown in lm79 report. the luminaireshall be bis certified and t.c. certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened ,color rendering index >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced. 19 oem must have its own in house nabl lab setup for all testing facilities forled fixtures.(lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 20 led street light fixture 60 watt 21 providing & fixing ofik07 ip 66 protected high power led flood light system with pressure diecast aluminium housing lm6/ adc12 material , toughened glass diffuser with suitable lenses on led to achieve various beam angles, 240 volt, 50hz, of high power led lamps . integrated driver must be potted & has a unique bis r number shall be high efficiency having efficiency more than 85 % and in compliance to bis certified and t.c. certificate. the system level luminaire efficacy >=120 lm/ wtwith high power leds is to be used . led driver input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety . input frequency 50hz±3%, power factor >0.95 ,driverefficiency >85% , thd(i) <10%, driver current <1000ma shown in lm79 report. driver should be phase to phase protection of 440 v for 4 hrs. electrical connector must be provided, surge protection min >=4kv internal and 10kv external, system life of 30000 burning hours with 70% of initial lumens maintained, color rendering index >70 and cct 5700k±355k.driver current <1000ma shown in lm79 report. manufactures word mark/name engraved/embossing/screen printing on die cast housing to allow traceability/authenticity. fixture shall be is 10322 complianced. 22 oem must have its own in house nabl lab setup for all testing facilities forled fixtures.(lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 23 high power led flood light 50w 24 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armouredaluminiumcable of 1.1 kv grade as per pwd specification for electrical worksin existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points (a), (b), (c), mentioned below: 25 (a) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i 26 (b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures . 27 (c)oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted .all above as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 28 armoured cable 29 6.0 sq. mm 30 2 core 31 4 core ...

Public Works Department - Rajasthan

29606300 replacement of water circulating pump and other accessories in a type bunglow and other bunglows at gandhi nagar, jaipur 1 supply installation testing & commissioning of iso certified manufacturer madepressure boosting pump with 24 ltr. ms tank, pressure switch, pressure gauge, and all standard fittings fully automatic on / off system, 2900 rpm with stainless steel casing, & impellor suitable for following capacity complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 2 1.0 hp ( 25 15 ) mtr, ( 30 48 ) lpm 3 providing & fixing of iso certified company made beestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanas per pwd specification for electrical works, conform to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) or quality certification such as iso – 9001 or above , with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 4 1200 mm sweep bee 1 star rated ( service value >=4.0 to <4. 5 ) 5 providing & fixing of capacitor start, copper wound, metal body, metal blade three speed wall mounting fan of following sweep with the help of anchor bolts including making connection testing etc. as required. oem shall be an iso certified company.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 6 400 mm sweep ( oscillating type ) 7 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. oem shall be an iso certified company.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 8 225 mm sweep 9 300 mm sweep 10 providing & fixing of heavy duty capacitor start, copper woinddouble ball bearing900 / 1400 rpm single phaseexhaustfan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 11 300 mm sweep ( 900 / 1400 rpm ) 12 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate / extruded aluminium powder coatedhousing with in built driver, power consumption of18w / 20w , system lumen efficacy = 120 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. 13 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product / work, refer annexure a attacheded with this bsr. 14 4 led tube shape fixture 18 / 20 w ( polycarbonate base ) 15 providing & fixing of ip20 led recessed / surface mounted, round / sqaure non dimmable back lit smd mid power led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal / external bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and in compliance to iec standards. system lumen efficacy min. 100 lm / watt, thd < 10 % , p.f.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oemmust have its own in house nabl acredeated lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product / work, refer annexure a attacheded with this bsr. 16 surface mounting 17 led downlight 18 / 20w 18 providing & fixing of ik07 ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminum lm6 / adc12 material with heat dissipation fins on housing with uv stabilized pc / toughened glass cover ( uv stablzation report submitted for uv cover ) and secondary lens on each led & should be smd type . the system level luminaire efficacy >=120 lm / wtwith high power leds is to be usedand potted driver must be potted & has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , input frequency 50hz±3% power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <1000ma shown in lm79 report. the luminaireshall be bis certified and t.c. certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , color rendering index >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced. 19 oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 20 led street light fixture 60 watt 21 providing & fixing ofik07 ip 66 protected high power led flood light system with pressure diecast aluminium housing lm6 / adc12 material , toughened glass diffuser with suitable lenses on led to achieve various beam angles, 240 volt, 50hz, of high power led lamps . integrated driver must be potted & has a unique bis r number shall be high efficiency having efficiency more than 85 % and in compliance to bis certified and t.c. certificate. the system level luminaire efficacy >=120 lm / wtwith high power leds is to be used . led driver input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety . input frequency 50hz±3%, power factor >0.95 , driverefficiency >85% , thd ( i ) <10%, driver current <1000ma shown in lm79 report. driver should be phase to phase protection of 440 v for 4 hrs. electrical connector must be provided, surge protection min >=4kv internal and 10kv external, system life of 30000 burning hours with 70% of initial lumens maintained, color rendering index >70 and cct 5700k±355k.driver current <1000ma shown in lm79 report. manufactures word mark / name engraved / embossing / screen printing on die cast housing to allow traceability / authenticity. fixture shall be is 10322 complianced. 22 oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 23 high power led flood light 50w 24 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armouredaluminiumcable of 1.1 kv grade as per pwd specification for electrical worksin existing rcc / hume / stoneware / pvc pipe / open duct / cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points ( a ) , ( b ) , ( c ) , mentioned below: 25 ( a ) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i 26 ( b ) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 ( part 0 to 64 ) for testing procedures . 27 ( c ) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted .all above as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 28 armoured cable 29 6.0 sq. mm 30 2 core 31 4 core...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

25784343 annual contract for deputation of service engineer for torishima make boiler feed pump and boiler circulating pump through oem m / s torishima pumps ( india ) pvt ltd.at ( 2x660mw ) csctpp chhabrais praposed to be hired through singel source bidding....

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

12683049 supply of quality control laboratory equipment at jaipur, 1.01 supply of micro controller based compressive testing machine with automatic pace rate controller, capacity 2000 kn. touch screen indicator, real time curve on indicator with 1.02 ( a ) capacity: 2000kn 1.03 ( b ) resolution : 0.1kn 1.04 ( c ) clearance between upper and lower platens ( min ) : 320mm 1.05 ( d ) platen size min : 220mm 1.06 ( e ) rame stroke :50mm 1.07 the machine should be suitable for: 1.08 ( i )  the compressive strength test for concrete cubes / cylinders as per is 516. 1.09 ( ii ) machine should conform to is: 14858. 1.1 ( iii ) supplied with 10 inch touch screen digital indicator, pumping unit, loading unit 1.11 specifications of digital indicator: 1.12 ( i )  digital indicator must be touch screen tft with 800x480 pixels 1.13 ( ii ) automatic pace rate control to set value 1.14 ( iii )  configurable engineering unit usb port available to communicate with software 1.15 ( iv ) dynamic calibration system 1.16  hydraulic pump unit 1.17 ( i )   it must have automatic pace rate control facility 1.18 ( ii )  single phase, 0.5 hp stepper motor driven two hydraulic pump seal free 1.19  loading unit 1.2 ( i ) the loading frame should be fully welded construction with a top crosshead, base, and solid side plates 1.21 ( ii ) metal door with a perspex window should be available for operator’s safety 1.22 ( iii ) suitable size of spacers provided 1.23 ( iv ) must be supplied with manufactures in house nabl accredited calibration certificate 1.24 supply of digital flexure testing machine with automatic pace rate controller capacity 100 kn. 1.25 the flexure strength testing machines are designed to test flexural strength of concrete beams. the design provide maximum rigidity throughout their working range. 1.26 flexure testing machines salient features : 1.27 ( i )      electrically operated. 1.28 ( ii )   digital display. 1.29 ( iii )    pace rate indicator. 1.3 ( iv )   data storage facility. 1.31 ( v ) suitable for 100x100x500 and 150x150x700 mm concrete samples. 1.32 ( vi )  supplied with hydraulic pumping unit, lading frame and digital indicator. 1.33 ( vii )         supplied with manufacturers nabl calibration certificate. 1.34 supply of asphalt content tester 1.35 to find out the bitumen content is most important and critical activity in road construction for the better quality roads. the conventional benzene method is not quick and accurate. ignition method developed by ncat usa is more accurate, user friendly and quick to measure the bitumen content. 1.36 machine ref. standard astm d6307 & en 12697 39 this machine is used to determine the asphalt content of hot mix asphalt ( hma ) paving mixture and pavement samples by removing the asphalt in an ignition furnace by means of sample heating not by means of solvents. machine should have digital display of temperature and must have inbuilt printing facility to generate a receipt that will contain all test parameters. 1.37 suitable for operation on 415v, 50hz, 20a, 3phase, ac supply. manufacturer must have irc accreditation 1.38 specifications 1.39 max weight of specimen: 4500g 1.4 suggested weight of specimen: 1000 to 1500g 1.41 accuracy of electronic balance 10kg x 0.01g 1.42 size of furnace: 350 mm x 440 mm x 330 mm 1.43 max. working temperature: 8000 c 1.44 standard working temperature: 5380 c 1.45 testing time 30 to 40 min 1.46 supply of accelerated curing tank for 12 moulds of 150mm x 150 mm size 1.47 specifications : 1.48 ( i ) temperature range 5 degree to 100 + 2 degree 1.49 ( ii ) suitable for 12 cube moulds of 150 mm 1.5 ( iii ) fully insulated 1.51 ( iv ) complete with hinged lid, heater, thermostat and recirculation pump 1.52 ( v ) two removable racks 1.53 ( vi ) arrangement for free circulation of water around each cube 1.54 ( vii ) pump, drain valve and other electric equipment must be housed in a separate compartment. 1.55 ( viii ) fully powder coated 1.56 ( ix ) three phase indicator in the front panel for presence of supply in individual phases. 1.57 ( x ) water circulating pump crompton greaves make. 1.58 ( xi ) hydraulic door closer 1.59 ( xii ) water level sensor inside the chamber 1.6 ( xiii ) outlet valve to be changed to 1” from 1 / 2 ”. 1.61 ( xiv ) act tray is made in two part. 1.62 ( xv ) levelling screw 1.63 ( xvi ) suitable for operation on 440v, 50hz. three phase, ac supply 1.64 supply of auto digital level 24x with standard deviation of 1 km. double run levelling + 2.5 mm. erect image, magnetic compensator. including aluminium stand, aluminium staff and all other necessary accessories. 1.65 supply of digital theodolite having 1” least count and 5” accuracy along with all standard accessories ( battery, battery charger, operation manual, tool kit and carrying case ) . including open frame wind resistance telescopic tripod, 3 legs of aluminium with adjust central lock, aluminium staff and other necessary accessories....