39795210 bids are invited for sc110400208 cast carbon steel swing check non return valve, size 4 inch , sc110400207 cast carbon steel swing check non return valve, size 6 inch , sc110400209 cast carbon steel swing check non return valve, size 12 inch , cs010190021 cast alloy steel wc9, gate valve, size 6 inch total quantity : 4...
39740910 supply of d shackle capacity 10 tone screw pin type for art confirms to is 6132 1971 grade 80 alloy steel along with test certificate from nabl approved lab [ warranty period: 30 months after the date of delivery ] ...
39533452 supply of 28 mm alloy steel grade 80 double chain sling with oblong link ( 56mm dia x 400mm i / l x 250mm i / w ) at the top and eye hook at each bottom, sling jointed with indlocks. effective length 8.0 meters, safe working load 35 mt, 90% b0 angle as per drawing ic / h2 ibe / 80 / 28 8.00 m, [ warranty period: 30 months after the date of delivery ] ...
39522029 supply of alloy steel en 31 round dia 50mm [ warranty period: 30 months after the date of delivery ] => limited...
39438100 supply of bow shackle capacity 10 tone screw pin type for art confirms to is 6132 1971 grade 80 alloy steel along with test certificate from nabl approved lab [ warranty period: 30 months after the date of delivery ] ...
39432494 supply of dropper wire cutter 12 inch ( alloy steel bolt cutters, 460 mm ) as per gem reference no. 5116877 8343723260 [ warranty period: 30 months after the date of delivery ] ...
39336215 supply of 28 mm alloy steel grade 80 double chain sling with oblong link ( 56mm dia x 400mm i / l x 250mm i / w ) at the top and eye hook at each bottom, sling jointed with indlocks. effective length 8.0 meters, safe working load 35 mt, 90% b0 angle as per drawing ic / h2 ibe / 80 / 28 8.00 m, ...
39333728 1 nos drain cleaning machine as per documents , machinery , 1. trailer trailer frame :ismc 100 towing hook :standard supporting leg :provided tyre size : 7.50 x 16.00 axle :solid bar 75 x 75 mm alloy steel rim :standard 2.bucket ( trolley ) volumetric capacity : 3.0 cum bottom plate : 2.5 mm thick ( is:2062 grade a ) side plate : 2.0 mm thick ( is:2062 grade a ) trolley tilting :by hydraulic system side stiffener : ismc 75 hinge for tilting :heavy duty hinge arrangement to be provided at the rear side tipping angle : 50 degree 3.machine structure lower boom :heavy duty rectangular pipe upper boom :heavy duty rectangular pipe capture bucket capacity : 0.03 cum or 30 ltr. maximum operating depth below ground level : 1.50 meter max. outreach : 3.0 mtr arm stewing : 1000 degree arm movement :hydraulically with four cylinder 4. hydraulic hydraulic cylinder :dantal, rmb or equal type of hydraulic cylinder :double acting hydraulic cylinder make :dowty hydraulic pump :25 cc / rcv control valve :bucher / wolvoil or equal fittings :s” series hydraulic oil tank : 30 ltr....
39327511 supply of alloy steel d shackle set of one each ( 1, 3 / 4, 5 / 8, 1 / 2 ) . make: sste [ warranty period: 30 months after the date of delivery ] ...
39285045 bids are invited for electrodes for manual metal arc welding of stainless steel and other similar high alloy steels as per is 5206 ( q3 ) total quantity : 20...
39096528 supply of 28 mm alloy steel grade 80 double chain sling with oblong link ( 56mm dia x 400mm i / l x 250mm i / w ) at the top and eye hook at each bottom, sling jointed with indlocks. effective length 8.0 meters, safe working load 35 mt, 90% b0 angle as per drawing ic / h2 ibe / 80 / 28 8.00 m, ...
39034416 supply of 1 / 2 inch square drive ratchet type torque wrench, with chrome molybdenum alloy steel square drive, torque range 20 100 nm, along with calibration certificate ( as per specification attached ) make : groz / gedore / facom / proto or equivalent [ warranty period: 12 months after the date of delivery ] ...
38902992 supply of draw hook, enhanced capacity ( alloy steel ) draw hook assembly used on railway coaches to drg. no. emu 2 1 011 alt g / 2 along with latest amendment / alteration if any as per rdso spec. c9509 ( rev. 02 ) with amendent 1 of oct.2016 for demu / dpc [ warranty period: 30 months after the date of delivery ] ...
38565617 supply of bow shackle capacity 55 tone screw pin type for art confirms to is 6132 1971 grade 80 alloy steel along with test certificate from nabl approved lab [ warranty period: 30 months after the date of delivery ] ...
38565504 supply of d shackle capacity 60 tone screw pin type for art confirms to is 6132 1971 grade 80 alloy steel along with test certificate from nabl approved lab [ warranty period: 30 months after the date of delivery ] ...
38450349 supply of enhanced capacity ( alloy steel ) draw hook assembly used on railway coaches drg.no. emu 2 1 011 as per rdso spec c 9509 ( rev.02 ) with amendent 1 oct 2016 ( guarantee / warranty certificate and test certificate is necessary with supply of item ) . [ warranty period: 30 months after the date of delivery ] ...
38401126 bids are invited for non return valves and gate valve sc11000208 cast carbon steel swing check non return valve, size inch , sc11000207 cast carbon steel swing check non return valve, size 6 inch , sc11000209 cast carbon steel swing check non return valve, size 12 inch , cs010190021 cast alloy steel wc9, gate valve, size 6 inch total quantity : 4...
38292021 material for vocational education construction lab , concrete mixerhalf bag concrete mixer 220 ltr, 230v 50 hz, 900 w s6 30%, drum opening 400mm, drum capacity 220 litre, drum speed 30/min, weight 80 kg, size 80 (mm) x 50 (mm) , electric drill up to 10mmtaparia /gadore/jhalani/pie or any other good quality brand, rated power input500 w, no load speed 0 2600 rpm, power output 250 w, weight without cable 1.5 kg,drill spindle connecting thread 3/8 24 unf, chuck capacity 1 10 mm, impact are at no load speed 0 41600 bpm , safety beltunisex adjustable safety belt (full body harness and lanyards) with hook options (scaffolding) and line attachments, made of high quality polyester, with alloy steel buckles, capacity up to 2000 kg , water tankwater tank to store water(must be with cover) , troweliron mason trowel with wooden handle(10 to 12 inches long and 6 inches wide) , plumb rule and bobheavy iron plumb rule and bob with chord (at least 3 meter ) approx. weight around 1 kg , spirit leveltaparia 300 mm spirit level level accuracy: 1 mm/m width (mm): 50 mm weight (kg): 0.165 kg length (mm): 300 mm height (mm): 20 mm material: aluminium frame and rubber moulding , try squarestailness ateel, 12 x 24 inch, 2mm thickness, approx 1 kg in weight , line and pinslarge headed line pins with zinc coating size 2mm , depth 12cm, along with 18 meters of builders line , brick bolster / brick chiselmade of carbon steel with dual hand guard, size 4 x 8, 1/2 inch , brick hammermade of iron with a hardened striking face and an opposing end with a roughing and shaping chisel blade attached with a wooden handle, size 12 inch, weight approx. 1 kg , scutch hammermade of iron withcomb slots at both ends to fit replaceable one inch scutch combs or chisel attached with a wooden handle, size 12 inch, weight approx. 1 kg , pick axeone side pointy plus one side chisel oval eye pick axe made of high quality iron, 10mm in thickness at widest point & 5mm at the narrowest point , crowbariron bar with a flattened end, used as a lever, diameter 25.4, length 1meter, weight approx. up to 3 kg , chisel6 inch iron chisel with thickness of 20mm at front and 18mm at back , mash hammer18 mash hammer hammer forged from a single piece of hard iron with approx. 2 kg in weight, round eye, attached with a wooden handle , boasterwith carbide tips made of heavy carbon steel. available with or without rubber grip. , spall hammerlarge hammer with a flat face and straight peen for breaking and rough dressing stone. the head is made of hard iron with wooden handle attached to it, weight approx. 2 kg, around 15 inches in , scrabbling hammerone side flat plus one side claw, high carbon steel hammer to dress stone and bricks approx. half kg in weight , bevel32mm bevel edge chisel brick stone masonry tool made of high grade steel, width 25mm, length 280mm , spadespade with sharper tips of metal made of hard iron, round eye with a wooden handle attached, weight approx. 3 to 4 kg , picks and beatersused for track maintenance, made of hard iron, length 1.5 feet, weight approx. 3 to 4 kg , wooden floatflat board with a handle to hold, made of hard wood for durability, size: 12? (300mm) x 5? (125mm). , metal floatsmooth metallic plain that is applied on flattened layers of mortar and concrete during surface finishing, made of steel with a plastic or wooden handle, size 12? (300mm) x 5? (125mm). , floating rulefloating rule made of aluminium, at least 4 meter long weight up to 2 kg , scratcherscratcher trowel made of steel 16 x 4 1/2 with wood handle , trowel (khurpi)made of hard iron with a wooden handle, 10 to 12 inch in size , measuring tape 5 metermeasuring tape of 5 meter of industrial type, made of steel, thickness 1 mm, length 5 meter. , wooden ladderbamboo ladders of 10 / 12 feet , wooden pole (balli)wooden poles of 10 & 12 feet for making wooden decks , wooden sievewooden sieve of large size , taslagalvanized iron tasla for construction, size 20 inch, hardness 50 7 hrc, thickness 1mm approx. , double wheel barrowdouble wheel barrow with rubber wheels, capacity 200 kg, length, width & depth 34x24x12, tapper depth 15 inch. , air wheel hand trolleyair wheel hand trolley with 250 weight capacity, made of hard iron, toe plate width 240 mm, weight approx. 16.5 kg, size: 1249x650x578 mm, wheel size: 10x3.5 inch , racking needle , hacking tool...
38288787 supply of hardware for cattle feed machinery , super senior pellet mill , bearing cover front forged steel , bearing cover rear forged steel , bearing setting ring forged steel , counter shaft assembly with pulley without belt without bearing & pedestal , die cover ring forged steel , die holder ( steel ) forged forged steel , die holder assembly forged steel , die holder rind rear suitable for above alloy steel , die holder ring front forged steel , feeder conditioner s. s. knife s.s. 304, thread 1 / 2 bolt per piece , feeder conditioner screw and paddle type feeder conditioner body s.s. approx. 1430 mm long s.s. 304 construction arrangement of single drive feeding end. , front bearing spacer for t’shaft , front scraper ( roll stay assembly ) forged steel with clamping stay , front scraper blades for pellet mill , pellet cooler air lock height 450 mm / width 250 mm inlet / outlet 155 mm , pellet cooler eccentric assembly , pellet cooler sensor , pellet die size:520 dia inner x 635 outer x 23.0 wider pellet :10 / 8 mm hole perforation fixing – 12 m 20 x 25 deep on 565 pcd mounting: tapper collar 12 deg on 620.6 dia or straight plug dia 610 dia material: en 19c or 42crmo4 duly hardened & temp. polished, rc4=5 , pulley assembly ( fly wheel ) 11 groove forged steel , rear scraper forged steel , roll holder shaft ( t shaft ) assembly forged steel , shearing pin , helical gear with hub one set containing 2 numbers , helical gear without hub one set containing 2 numbers , pellet mill sieve , screw for variable speed feeder conditioner for pellet mill , shear pin holding body , shear pun bush , spring set , teflon bush for main t shaft , pallet down spout , press roll assembly super senior , bearing cover , bearing retainer / nut for eccentric shaft km 20 , center bolt / roller stud ( allen, bolt, headtype design ) , circlip ( dia 180 inside ) , clamping device tension ring ( 90x101x17 ) mm , distance ring , eccentric shaft , lock nut with lock washer for press roll eccentric shaft , lock washer ( mb 20 ) , nut for center bolt ( lighting ring ) , press roll assembly complete with shell, bearing etc. suitable for above en 24 shell , press roll shell , setting ring , spacer ( sealing ring ) , molasses mixer , molasses cutting knife with nut suitable for above ni, hard duly balanced , paddle plane and loop type suitable for above ni, hard duly balanced , spray pipe nozzle with nipple 1.5 inch c class pipe, 3 / 8 inch nipple , full circle hammer mill , beater ( flat type ) all equal weight ( big size 180 mm x 50 mm x10 mm ) ni hard, dynamically balanced , beater ( flat type ) all equal weight ( small size 140 mm x 47 mm x 06 mm ) , beater holder shaft en, material , beater holding bush ( size length 30 mm, in dia 20 mm, outer dia 30 mm ) , beater holding bush ( size length 60 mm, in dia 20 mm, outer dia 30 mm ) , beater holding bush ( size length 36 mm, in dia 20 mm, outer dia 30 mm ) , beater holding bush ( size length 53 mm, in dia 20 mm, outer dia 30 mm ) , carryingrod for hammer mill 2 no of each set , door closing clamp set , hammer mill feeder , permanent magnet , sieve set 3 mm, thick ms sheet with 3 mm, 2mm, 4mm, 5mm and 6mm perforations , sieve set clamping frame , screw conveyor , gravity pipe clamping 8 inch dia. , gravity pipe clamping for above pipe 8 inch dia, 16 gauge. , gravity pipe m.s. 8 inchdia, 16 gauge, 1 meter long , gravity pipe s.s. 8 inch dia. 14guage 1 mtr. long. , pazama flap 3 way for distribution suitable for 8 inch pipe , screw of different sizes , shaft suitable for joining the screwconveyor , chain conveyor , raddler chainmatching our existing chain conveyor. chain should 10mm thick links along with bushes and roller duly hardened , chain supporter with single bearing nylon roller with shaft and bearing 1 no., lock ring, shaft 255mm long , chain supporter with double bearing nylon roller with shaft and bearing 2 no., lock ring, shaft 255 mm long , chain supporter ( 3 piece bush ) nylon roller without bearing, shaft 310 mm with nut and washer, 94.5 bush 2 no., 60 mm long bush 1 no. , slat conveyor , chain suitable for slat conveyor matching to our existing slatconveyors. chain links should 6 mm thick along with bushes and roller dully hardened , metal slates , chain sprocket , 1 simplex 11 teeth, ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 15 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 16 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 17 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 22 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 32 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 42 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 duplex 45 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 duplex 17 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , 1 simplex 19 teeth ( bore different size, keyway 1 / 2, 2 nos. with thread, bose 65mm ) , pinions & wheels , 1st pinion 4380 , 1st pinion 4382 d , 1st pinion 4419 , 1st pinion 4601 , 1st pinion 4220 , 1st pinion 4295 , 1st pinion 4418 , 1st pinion 7530 , 1st wheel 724 , 1st wheel 345 , 1st wheel 1150 , 1st wheel 797 , 1st wheel 215 , 1st wheel 2336 , 1st wheel 704 , 2nd pinion 365 , 2nd pinion 833 c , 2nd pinion 621 , 2nd pinion 3388 , 2nd pinion 4229 , 2nd pinion 181 , 2nd wheel 366 , 2nd wheel 182 d , 2nd wheel 619 , 2nd wheel 3386 , 2nd wheel 4418 , 3rdpinion 179 , 3rd pinion 3319 , 3rd wheel 3377 , gear wheel 545 , gear wheel 729 , pinion 4343 , pinion 4347 , pinion wheel 544 , pinion wheel 431 , wheel 180 , wheel 253 , wheel 3371 , wheel 694 , 1st pinion 4237 , 1st pinion 4748 , 1st wheel 259 , 1st wheel 9036 , 2nd pinion 352 , 2nd pinion 631 , 2nd pinion 574 , 2nd pinion 572 , 2nd pinion 573 , 2nd wheel 353 , 2nd wheel 571 , 3rd pinion 3379 , gear 570 , gear 637 , pinion 4386 , pinion 642 , elevators , elevator beltm 24 rubber 300 mm 4 ply ( polyester ) 3mm top 1.5 mm bottom , elevator beltm 24 rubber 250 mm 3 ply ( polyester ) 3mm top 1.5 mm bottom , seam less buckets 10” size 10”× 6”× 5” gauge 18hole 3 / 6” 3 nos. , seam less buckets 8” size 8”× 5 ½ × 4 ½” gauge 18 hole 1 / 8” 2 nos....
38180721 providing and fixing of play equipments at municipal board jhalrapatan 2 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake combo maps: area:3.95m x 3.95m safe area :4.85m x 4.85m height:2.4 m vertical support : 1.5” ( 48mm nb )see saw stand : 1.5” ( 48mm nb )see saw center support : 2”( 60mm nb )see saw railing : ¾” ( 25mm nb )ladder : 1” ( 32mm nb ) & rectangle pipe 2” x 1” (50 x 25mm) for stepsladder hand railing : ¾” ( 25mm nb )top : 1”( 32mm nb )& ¾” ( 25mm nb )frp slide length : 2.4 m ( thickness : 5mm )frp see saw seats : 12” x 8” ( thickness : 3 mm )platform: 2” x ½” (50 x 15mm) rectangle pipe.providing & fixing of combo multi play having area 3.95 x 3.95 meter. the total height should be above ground level is 2.4 meter.square deck 4’ height: the platform is made in fiber reinforced plastic. the top of platform is anti skid surface with multi colour pigmented resin .the back coat of fiber reinforced plastic is such that the mat strands are not visible and the surface is tack free. it should be made by 16 gauge crc sheet with frp non skid lamination and connected leg support pipe should be made by 48mm nb pipe with proper fitment. the shape of platform support at one end is arch type.frp slide 8’: there is 1 no. of frp slide of length 2.4 meter having 5mm thickness connected to the one end of platform. the slide should be made by fiber reinforce plastic 5 mm thick.see saw single: the main structure made up with 48mm nb pipe & center support of see saw single made in 60mm nb pipe rest on the main stand. the center support is attached with 2 nos. frp seats of size 12” x 8” having thickness 3mm for the seating. the railing of see saw center rod made with 25mm nb pipe.ladder:ladder should be made with 32mm nb pipes for support & the steps should be made with rectangle pipe of 50 x 25mm. the ladder railing made with 25mm nb pipe. top climber: the top of the climber made up with 32mm nb & 25mm nb pipe.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. slide should be made in a single mould piece there is no any joint in the slide.frp components should be paint by 3 layers of pu paint. and install by c.c. base system as per order by engineer in charge. 3 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake all in one multy play system: area : 10 mtr x 12 metersafe play area: 11 mtr. x 13 mtr.platform height: 1.5/ 1.8/2.1 mtr.providing and installation ofmulty arrangement play system whichis consist towers , v bridge , arch bridge , lemon bridge , connector tube , tire ramp , frp canopy’s , party swing , multy seater see saw , rainbow climber , swing two seater, both types of frp slides , plain ladder , snake shape ladder , tic tack toy steps and different types railing. all work shall be done by as per specification and order by engineer in charge.1. towers and decks: all the towers should be made by 40 mm idgi pipe at lag support and platform should be made by 18 swg crc sheet. supporting pipe connected with frp canopy with proper fitment no sharp corner seen on the top and other place on the tower. platform height from ground level 6’ and 7’ and total height from ground level are 13’. and there are proper space for standing 3 4 children’s on all types of deck.2. 2. v bridge: v type bridge should be made by 20 mm idgi pipe. in inner frame and 25 mm idgi pipe at outer frame and shall be connected with towers with proper fitting arrangement like nut bolts or proper welding system hand rills and railing should be made by 15 mm idgi pipe. and brightly paint by 3 layers of p.u. paint in multy color.3. arch bridge: this bridge should be made by 20 mm idgi pipe. in inner frame and made like cross shapeand 25 mm idgi pipeat outer frame ladder shall be made by 2”x1/2” rectangle pipe. and connected like such a way to go one tower to another towers. all the equipment joint cross welding system. there is no any sharp corner on the top of the bridge, all components brightly paint by 3 layers of p.u. paint in multy color.4. 4. lemon bridge: lemon bridges outer frame should be made by 25 mm idgi pipe. and handrails should be made by 20 mm idgi pipe. bridges ladders should be made by 2” x ½” rectangle pipe. total length 3.0 mtr. x 0.75 mtr. in half round shape all the equipment joint cross welding system. there is no any sharp corner on the top of the bridge , all componentsbrightly paint by 3 layers of p.u. paint in multy color.5. connector tube or circular shape bridge: the connector should be made look like circular shape or round shape supporting pipe shall be made up of 20 mm idgi pipe. and circular shape pipe shall be made up of 25 mm idgi pipe both types of pipe are connected each other with cross wilding arrangement there is proper way to go one deck to another deck.all the components fitted by proper fitments with towers there is no any sharp corner show on the top of the bridge., all components brightly paint by 3 layers of p.u. paint in multy color.6. tyre ramp: ramps steel frame should be made by 40 mm idgi pipe and well joint with 6 nos. of heavy duty tyres and connect specifically on the ramp. ramp shall be connected with platform by proper fitting arrangements like nut bolts or proper welding system. handrails and railing should be made by 20 mm idgi pipe. , all components brightly paint by 3 layers of p.u. paint in multy color.7. frp canopy: alltypesof frp canopy should be completely made up of fiber glass reinforced plastic heaving thickness 3 mm allover on the canopy proper mounted top of each and every tower , all componentsbrightly paint by 3 layers of p.u. paint in multy color.8. plane ladder: the ladders should be made by 25 mm & 20mm idgi pipe and steps should be made by 2” x 1” rectangle pipe of size 100x 25 .proper welding with smooth finishing there is no anythere is proper way to go one deck to another deck.all the components fitted by proper fitments with towers there is no any sharp corner show on the top of the bridge., all components brightly paint by 3 layers of p.u. paint in multy color.9. snake type ladder: this ladder should be look like such a snake shape and made by 25 mm idgi pipe for climbing for children’s and connected with side panel of lemon bridge. all the components joint cross welding system. there is no any sharp corner show on the top all components brightly paint by 3 layers of p.u. paint in multy color.10. tic tac toy : total 9 nos. of x and o frp cylinders made up of fiber glass reinforced plastic with 8” dia and 9” of length. and fitted on frp window panel. total length of frp window panel are 0.8 mtr. x 0.8 mtr. and fitted left or right side of tyres ramp. paint by pu paint in multy color.11. frp wave slide: slide should be made up offiber glass reinforced plastic having thickness 5 mm all over on the slide with both side smooth finishing total length of slide 3.6 mtr. and width 0.6 mtr. slide should be connected with a platform with proper fitment like nut bolts or clam system and brightly paint by 3 layers of the epoxy coated paint.12. frp long slide: slide should be made up of fiber glass reinforced plastic having thickness 5 mm all over on the slide with both side smooth finishing total length of slide 3.0 mtr. without joint and width 0.5 mtr. slide should be supported by 20 mm idgi pipe slide should be connected with a platform with proper fitment like nut bolts or clam system and brightly paint by 3 layers of the epoxy coated paint.13. straight slide: slide should be made up of fiber glass reinforced plastic having thickness 5 mm all over on the slide with both side smooth finishing total length of slide 4.2 mtr.and width 0.6 slide should besupported by 20 mm idgi pipe slide should be connected with a platform with proper fitment like nut bolts or clam system and brightly paint by 4 layers of the epoxy coated paint.14. rainbow climber: rainbow climber shall be made up of25 mm idgi pipeat outer frame and 20 mm idgi pipe in inner frame. total height 2 mtr. from ground level. connected with platform with proper fitment like nut bolts or gross welding system and brightly paint by 4 layers of pu paint. there is no any sharp corner show on the top.15. multy seater see saw: there are 1 no. of see saw (4 seater) should be made by 50 mm idgipipe for center support and leg support shall be made up of 40mm nb pipe. hand railing should be made by 20 mm idgi pipe. seating arrangement for children shall be made up of fiber glass reinforced plastic 4 mm frp thickness with smooth finishing and brightly paint by 3 layers of pu paint. there is no any sharp corner show on the top.16.swing two seater: its total required area 3 mtr. x 1.5 mtr. and height shall be 2.4 mtr. from ground level top bar of swing is made by 50mm idgi pipe 16 gauge. and 4 nos. of leg support pipe should be 40mm idgi pipe 16 gauge.top bar attach with 2 nos. of alloy steel coasting bearing with gi chain. seating arrangement of swing is made up of 9mm thick. anti skid chequered reinforced rubber belt. bearing should be covered by specially design nylon clamp. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge.17. party swing 4 seater: party swing should be made by 40 mm idgi pipe and connected on the front slide of the bridge, seating arrangement should be made up of 18 swg crc sheet having thickness 1.5 ,, and laminated by frp plane and smooth sheet. total seating capacity of 4 children’s. all the sharp edges and corner properly grinded to give smooth finishing. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge. 4 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake maps joy : safe play area 4.5 mtr. x 3.5 mtr.area – 3.5 mtr. x 5.4. mtr.height 3.6 mtr with canopyproviding & fixing maps joy its total required are 3.5 mtr x 5.4 mtr. and consist 4 no. of equipments.01 strate slide should have 2.4 mtr. length and width 0.5 mtr. and made up of frp 5 mm thickness over all. paint free.02 1 no. of square deck platform should be made frp non skid lamination and connected leg support pipe.03 frp canopy fitted on the platform and made up of fiber glass reinforced plastic with 3 mm frp thickness. with 60 mm idgi pipe in leg support.04 bridge climber shall be made by 25 mm idgi pipe and capsule pipe at bottom of the bridge.05 square deck without canopy should be made frp non skid lamination and connected leg support pipe.06 ladder should be made up of 1’’ x 2’’ rec. sq. powder coated pipe for proper footrest of children’s. safety railing and handrills should be made up of 20 and 25 mm nb pipe.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 12 year. 5 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake 3 way multi action play system mini combo with 4 loop climber : safe play area – 6 mtr. x 4 mtr.area – 5 mtr. x 3 mtr.height – 2.4 mtr. its required area 5mtr x 3mtr and height should be 2.4 mtr. from ground level connected with four nos. of equipments. 1 no. of frp slide should have length 2.4 mtr. x 0.5 mtr. shall be made by frp 5mm thickness overall slide should be connected with item nos. 2 rainbow junior climber should be made by 25mm idgi pipe in outer frame and 20mm nb gi b’ class pipe. inner frame should be connected with platform. platform should be made by 16 g thickness in steel frame and covered by frp non skid sheet. platform should be connected with item no.3 swing single seater having height 2.4 mtr. connected with 40mm nb pipe on top bar and joint with 35 mm nbgi b’ class pipe. for leg support swing made by 6mm. heavy duty chain joint with frp seat should have 5 mm thickness in frp. supporting pipe connected with see saw single board made by 40 mm. nb b class pipe. with have two proper fitting arrangement seat should made by 5 mm frp seat. 1 no of loop climber proper fitted with platform, there is 4 no of loop in climber. all equipments paint by 3 layer of p.u. paint in multi colour or oven baked powder coated whichever is feasible and possible. 6 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake combination set 3 in oneas per specification: age group: 2 4 yrs.product area : 2.0 m x 1.6 msafe play area : 3.0 m x 2.6 mas the name suggests, this item has a combination of three items such as swing, slide and seesaw. the complete frame of this item is fabricated from 20 nb and 25 nb powder coated gi pipes. the slide in the combination set is made up of fiber reinforced plastic (frp). the slide landing support is made in 20 nb pipe. the slides are given a smooth finish so that the child does not hurt itself while playing on it. the bucket swing is made up of frp and is attached to a nylon rope/ chain. for the bucket swing a handle is given for gripping, which is made in rotational molding and out of frp. the see saw lever and stand is made up of 20 nb gi pipe. the see saw seat is made out of frp 3 mm. the bearing used is of heavy duty bush type. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments and install by c.c. base system as per order by engineer in charge age capacity 6 12 year. 7 providing and installation of uday creations kilkari, arihant playtime, svr, arasumakecriss cross : rec. age: 4 12 yrs.the area : 1.4 m x 1.4 msafe play area : 2.4 m x 2.4 mheight : 2.1 mthis is very simple type of structure similar to the shape of the ladder arranged in criss cross manner. the main frame of this criss cross scrambler is fabricated from 25 nb powder coated gi pipe. there is one centre support of 40 nb gi pipe and horizontal bars of 20 nb pipe. the pipes conforming to is 1239 with gi thickness of 60 µ are powder coated to prevent rusting due to atmospheric condition all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 4 12 year. 8 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake hanging climber: safe play area 3.4 mtr. x 2.2 mtr. dia area: 2.4 mtr. 1.2 mtr.height 2.4 mtr.it required area 2.4 mtr x 1.2 mtr & height 2.4 mtr and leg support should made up of 50 mm idgi pipe outer frame should be made by 32 mm idgi pipe in main frame joint with 20 mm idgi pipe in handrails/inner frame in dia. ladder should be made by 20 mm idgi pipe. and connected with proper fitment like welding, fastener.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge age capacity 6 12 year. 9 providing and installation of uday creations kilkari, arihant playtime, svr, arasumaketurbo tower : age group: 4 12 yrs.product area : 1.8 m diametersafe play area : 2.8 m diameterheight : 3.35mmaterial specification:in this interesting turbo tower the center support is made up of 80 nb powder coated gi pipe. the loops given to the turbo tower are made up of 15 gi powder coated gi pipe. the rings of the turbo tower are made up of 20 nb powder coated gi pipes. the bend pipes are made in 25 nb gi pipes. there is a sufficient distance between the rings for the children climbing on it. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 4 to 12 year. 10 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake snake climber: safe play area 4.5 mtr. x 2.0 mtr.area : 3.6 x 1.0 mtrheight 2.4 mtrits height 2.4 mtr. and length should be 3.6 mtr. and width should be 1.0 mtr. and made by 50 mm idgi pipe in vertical support and 32 mm nb pipe in outer frame. handrails should be made by 25 mm idgi pipe. leg support should be 50 mm idgi pipe. ladder should be made by 20 mm idgi pipe.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge age capacity 3 8 year. 11 providing and installation of uday creations kilkari, arihant playtime, svr, arasumakesky rocker : age group: 5 12 yrs.product area : 2.5 m x 0.6 msafe play area : 3.5 m x 1.6 mheight : 2.40mmaterial specification:the sky rocker is the most attractive and enjoyable of its kind. the main frame support is made from 80 nb gi pipe. while the top pipe is of 40 nb and 20 nb gi pipe. the top pipe is inserted into a nylon bush which gives the rider a swinging experience to enjoy. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge age capacity 6 12 year. 12 providing and installation of uday creations kilkari, arihant playtime, svr, arasumakerotary thrill mgr : safe play area 2.5 mtr. diaarea: 1.5 mtr. diaheight 1.0 mtr.its total required area 1.5 dia mtr. outer frame should be made by 32 mm idgi pipe and handrail and leg support should be made by 20 mm idgi pipe. center pipe should be made by 48 mm idgi pipe. connected with heavy duty ball bearing 6312 reputed make only. seating arrangement should be made by fiber glass reinforced plastic with 5 mm thickness. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 8 year. 13 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake jumbo slide12’: safe play area: 4 .6 mtr. x 1.5 mtr.area – 3 mtr. x 0.6 mtr.height: 3.0 mtr.its required area 3.0 mtr. x 0.6 mtr. platform height should be 1.5 mtr. from ground level and slide length 3.69 mtr. slide should be made by fiber glass reinforced plastic having thickness 5mm overall. the back side of slide is surface mat with phantom effect. connected with platform should be made by 16 swg crc sheet with frp non skid lamination. leg support of the platform should be made by 48mm nb pipe 14 gauge. ladder should be made by 32mm nb pipe.the ladders railing should be made up of 25mm nb pipe it is design in such a way that a ladder itself has safety railings for the platform. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. slide should be made in a single mould piece there is no any joint in the slide.frp components should be paint by 3 layers of pu paint. and install by c.c. base system as per order by engineer in charge. 14 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake standardslide : safe play area 3.4 mtr. x 1.5 mtr.area – 2.4 mtr. x 1.5 mtr.height 1.2 mtrits required area 2.4 x 1.5 mtr. platform height 1.2 mtr. in ground level should be made by 32mm idgi pipe for leg support. the ladders railing should be made up of 25mm idgi pipe & it is design in such a way that a ladder itself has safety railings of 2”x1” rectangle pipe of size 50 x 25mm for the platform. slide length 2.4 mtr. with 5 mm thickness overall slide chute 0.5 mtr. wide. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 10 year. 15 providing and installation of uday creations kilkari, arihant playtime, svr, arasumakefrp spiral slide : safe play area 3.5 mtr. x 2.7 mtr.area: 2.5 mtr. x 1.7 mtr.height 2.1 mtr.the spiral slide is made up of fiber reinforced plastic (frp) in one piece having shell thickness of 4 5 mm. the slide is supported on a center support 80 nb gi pipe. the landing supports of the slide are supported by two 20 nb pipes. the slide ladder steps should be made with 2”x 1” rectangle pipe of size 50 x 25mm. railing should be made by 25 mm nb pipe.the safety railing of the ladder is made25 mm idgi pipe. the spiral slide platform is made up of fiber reinforced plastic (frp). the trade and riser of the ladder are designed in such a way it wont entrap childs foot while playing.all the sharp edges and corners are properly grinded to give smooth finish so that children are not hurt while playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments and install by c.c. base system as per order by engineer in charge age capacity 4 12 year. 16 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake eaglesee saw: safe play area – 2.5 mtr. x 3.5 mtr.area – 1.5 mtr. x 2.5 mtr.height – 0.8 mtr.it’s required area 1.5mtr x 2.2mtr. main frame should be made by 80mm idnb centre pipe with proper fitment for installation of see saw.handle should be made by 25 mm idnb pipe. total height 0.5mm from ground level. 2 nos. of sheet made by 3 mm thick frp with proper seating arrangement grouted in cc. foundation base all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments and install by c.c. base system as per order by engineer in charge age capacity 6 12 year. 17 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake spring rider: safe play area – 1.9 mtr. x 1.7 mtr.area – 0.9 mtr. x 0.7 mtr.height – 0.5 mtr.providing & fixing of spring rider its required area 0.9 mtr x 0.7 mtr. total height 0.5mtr from ground level. leg support should be made by 40 mm idgi pipe & handle made by 15 mm nb pipe. seat should be made by frp animal duck / horse shape with 5 mm thick connected with heavy duty spring. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 12 year. 18 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake swing double seater : safe play area 4 mtr. x 2.5 mtr.area: 3 mtr. x 1.5 mtr.height 2.4mtrits total required area 3 mtr. x 1.5 mtr. and height shall be 2.4 mtr. from ground level top bar of swing is made by 60mm idgi pipe. and 4 nos. of leg support pipe should be 60mm idgi pipe.top bar attach with 2 nos. of alloy steel coasting bearing with gi chain. seating arrangement of swing is made up of 10mm thick. anti skid chequered reinforced rubber belt. bearing should be covered by specially design nylon clamp. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge. 19 providing and installation of uday creations kilkari, arihant playtime, svr, arasumake circular swing : safe play area: 2.5 m x 3 mthe area : 1.5 m x 2 mthe leg support of this item is made up of 40 mm, while the top bar is from 50 mm powder coated gi pipes. the swing frame is made from 25 mm and 15 mm powder coated gi pipes. there are two seats provided which are made out of fiber reinforced plastic. the platform is made using chequered plate for footrest and bearing assembly is made. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. slide should be made in a single mould piece there is no any joint in the slide.frp components should be paint by 3 layers of pu paint. and install by c.c. base system as per order by engineer in charge. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 10 year. 20 providing and installation of kilkari, arihant playtime, svr, arasumake frp dustbin penguin shape: height 1.3 mtr.thickness: 3 mm in frp.its total height 1.3 mtr. from ground level and made up of fiber glass reinforced plastic with 3mm thicknessand made by complete frp process using 450 gsm mat with resin, hardener and furnish by reputed make pigments in multy colors.paint by 3 layer of p.u. paint in multy color. and install by c.c. base system as per order by engineer in charge. 21 providing and fixing of kilkari, playtime, svr, arasu make frp spiral slide 3.0mtr. : safe play area 3.0 mtr. x 2.7 mtr.area: 2.0 mtr. x 1.7 mtr.height 3.0 mtr.its total required area 2.0 mtr. x 1.7 mtr. from ground level. slide length should be 3.0 mtr. with 5 mm thickness in frp slide should be smooth finished at sliding part and connected with platform should be made up of frp non skid sheet and having height 3.0 mtr. from ground level slide should be supported by 80 mm idgi pipe. railing and ladder should made by 20 mm idgi & 25mm idgi pipe steps should be made by 25mm idgi & 2”x 1” rectangle pipe of size 100x25 respectively.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 10 year. 22 providing and fixing of kilkari, playtime, svr, arasu make frp wave slide : safe play area 5.2 mtr. x 1.6 mtr.area: 4.2 mtr. x 0.6 mtr.height 1.5 mtr.providing & fixing of wave slide its total required area 4.2 mtr x 0.6 mtr. platform height 1.5 mtr. from ground level connected with leg support 60 mm nb pipe & ladder steps should be made with 2”x 1” rectangle pipe of size 100 x 25. realing should be made by 25 mm nb pipe. total slide length 3.0 mtr. with 5 mm frp thick.. slide should be made in a single mould piece there is no any joint in the slide.frp components should be paint by 3 layers of pu paint.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments and install by c.c. base system as per order by engineer in charge age capacity 6 12 year. 23 providing and fixing of kilkari, playtime, svr, arasu make tabular see saw 2 seater: safe play area – 2.5 mtr. x 4.5 mtr.area – 1.5 mtr. x 3.5 mtr.it’s required area 1.5mtr x 3.5mtr. outer frame should be made by 60mm idgi pipe connected with 80mm idgi centre pipe handle should be made by 32 mm idgi pipe. total height 0.5mm from ground level. 2 nos. of sheet made by 5mm thick frp with proper seating arrangement grouted in cc. foundation base all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating (oven baked) done on the pipes extend the life of equipments and install by c.c. base system as per order by engineer in charge age capacity 6 12 year. ...
38125822 supply of draw hook, enhanced capacity ( alloy steel ) draw hook assembly used on railway coaches to drg. no. emu 2 1 011 alt g / 2 along with latest amendment / alteration if any as per rdso spec. c9509 ( rev. 02 ) with amendent 1 of oct.2016 for demu / dpc [ warranty period: 30 months after the date of delivery ] ...
38064342 bids are invited for chromium molybdenum alloy steel pipe fittings meter , number total quantity : 713...
37976593 bids are invited for gasket blanking plate , gasket , ring retaining , rubber o , seat , pin , gasket lock pully , retainer gaasket , gasket aerator , plug magnetic , pin master , gasket connetion , plug , o ring , washer , clamp hose , nut , connection fuel drain , nut cross read , spring , cock drain , tde plate , pivot pin , pivot pin allooy steel , pivot pin alloy steel , lynch pin , rivot pin alloy steel , side cutter rh , side cutter lh , rivot pin alloy steel , pivot pin alloy steel , bucket tooth , side cutter lh , side cutter , cold seater kit , capsule , adapter flange , presure hose , seal kit , rak seal , bush , seal , bush spring steel , side light , blade lift cylinder kit , rod inertia brake adjusting , cable seal clutch , transmission seal , universal joint , fuel filter , ignitation switch , hyd cylinder seal , transmission filter , ammeter , pressour gauge , screen , pivet pin , fuel filter element , elect temp gauge total quantity : 212...
37976132 bids are invited for alloy steel unequal tee sa234 wp 22 fitting size 350nb x 350nb x 200nb (q3) total quantity : 10...
37897208 supply of spare parts, hardware and bearing for co operative cattle feed factory jhotwara jaipur , a) .pallet die material should be en 24 od – 530 mm id – 420 mm face width – 154 mm coller depth – 17 mm coller od – 489 mm hole size 10mm the firm giving rate for this item should mention the out put guarantee from each die. , b) press roll shells with lock material en – 24 od – 207 / 211mm id – 150mm face width – 117 grove depth – 6mm and as per our sample , c) pallet die with 4 nos. of press roll shells with lock specification given as above , a) t – shaft: as per our sample material en 24 , b) extra mouthpiece suitable for roller holder shaft (t shaft) made of spring steel. as per our sample , die holder ring(front rear wearing ring) as per our sample. material alloy steel od – 560 id – 410, face width (thickness – 35) having8 nos. holes at equal distance , pellet die cover as per our sample. material : alloy steel , eccentric shaft: material en 24 and as per our sample , bearing cover (plates) for eccentric shaft material: en – 24, and as per our sample , set of sieve for hammer mill (grinding machine). each set should be made of 2 n0s. (top and bottom) made from ms sheet 4mm thick and having holes dia. 6mm / 8mm and shape and size should be as per our sample , spare sieve sheets suitable for our fixed gravity type sieve. each sieve sheet should be made from stainless steel having holes 6mm dia and as per our samplel – 70”,w 17 .25” , roller studs (center bolts) with one cup nut and four piece of tansion ring. material en – 24, and as per our sample , shearing pin (bolt) material ms and as per our sample , check nut for eccentric shaft material en – 24, and as per our sample , elevator buckets : material from 2.5mm thick ms sheet , molasses beaters : material ni hard and as per our sample appox. wt. 650 700 gm. , molasses cutting knives material ni hard and as per our sample appox wt. 520 550 gm. , new rotor pellet feeder conditioner rotor hollow pipe & armsshould be of stain less steel while end shaft should be of solid ms. size and shape should be as per our sample , paddles suitable for screw conveyor made from harded ms, as per our sample , chain sprocket made from alloy steel having: 1 pitch: 13 teeth 21 teeth 24 teeth 57 teeth , scrapper assembly made of tempered ms and as per our sample. i) front ii) rear , die holder capsule for senior pallet mill. material en 24 , paddle shaft with discharger conveyer in 2” dia. length of screw shaft 50” length of paddle shaft 100” , paddle shaft for intake conveyer in 1.5” length of paddle shaft 1 x 8’ length of screw shaft3x8’ , gun metal bush shaft 8” with collar , gun metal bush shaft 8” with &without collar , gun metal bush shaft 2” gun metal bush , gun metal bush shaft 1.5” gun metal bush , bearing cover for capsule of 13.5” dia material en – 24, as per our sample , pellet die machine gate of ms with ss liner (inside) as per our pallet machine , cooler pipeline with cyclone as per sample , pellet cooler as per sample , electric motor (semance) delta star 150 hp , gear motor 5 hp (semance make) , body of molasses machine as per sample , cooler pipeline as per sample , slat conveyor machine length 36 feet 4x12 as per sample , 3 hp gear motor , 5 hp gear motor , 10 hp gear motor , bearinngs a) 32224 (make_zwz) , b) 32217 (make_zwz) , c) 1313 k (make_zwz) , d) ucp 20840mm (make_ntn) , e) ucp 2081.5” (make_ntn)) , f) ucp 2112” (make_ntn) , elevator belt width 10,” 4 ply 36 mtr. (make_mrf) , v – belts (make_fanner) a) a – 54 , b) b – 62 , c) b – 95 , d) c 180 , tyre f 80 (make_fanner) , fire packing sheet , namda pecking , welding rod no. 8 , welding rod no. – 10 , nut bolt a) 6 soot 8” b) 6 soot 3.5” half thread c) 6 soot 1. 5” d) 5 soot 4” e) 3 soot 1” f) 3 soot 1.5” g) 3 soot 2” h) 3 soot 2.5” i) 3 soot 3” j) 2 soot 1.5” k) 1/2”x1” l)1/”x1.5” m)½”x2” n) ½”x3.5” half thread o) ½”x4”half thread p) 2 soot 1.5” do with nut , l n key bolt a) ½”x1” ¾”x 2” 2 ½ soot 1” , washer and nut a) 6 soot b)½ soot c) 3 soot d) 5 soot e) 2 soot , fevicol => limited...
37788253 bids are invited for expandable items h1 b desiccant silica gel , g2 electrode welding high alloy steel 3.15m , g2 electrode welding steel armour 3.15mm , g2 electrode welding steel high tensile 3 , h1 fevicol sr 998 , h1 a varnish oil g s , h1 b flux soldering paste , h1 b glue ordinary , h1 mineral jelly ammunation , g1 nails steel wire round 100mm 5 x point 0 mm , g1 nails steel wire round 25mm x 2mm , g1 nails steel wire round 40mm x 2mm , h1 paint air dry br spr syn ena dark grey , h1a paint rfu fin syn br spr deep cream total quantity : 1396...
37781768 bids are invited for 1.supply of brass hexagonal rod of size 12 mm , 2.supply of brass hexagonal rod of size 18 mm , 3.supply of brass hexagonal rod of size 25 mm , 4.supply of brass hexagonal rod of size 28 mm , 5.supply of brass hexagonal rod of size 32 mm , 6.supply of brass hexagonal rod of size 36 mm , 7.supply of brass hexagonal rod of size 44 mm , 8.supply of brass hexagonal rod of size 50 mm , 9.supply of brass hexagonal rod of size 60 mm , 10.supply of brass hexagonal rod of size 80 mm , 11.supply of brass round rod of size 12 mm dia a , 12.supply of brass round rod of size 18 mm , 13.supply of brass round rod of size 20 mm dia , 14.supply of brass round rod of size 25 mm dia , 15.supply of brass round rod of size 36 mm dia , 16.supply of brass round rod of size 80 mm dia , 17.supply of aluminum bronze rod of diameter 50mm , 18.supply of aluminum bronze rod of diameter 80 mm , 19.supply of aluminum bronze rod , 20.supply of grey cast iron rod , 21.supply of grey cast iron rod of size 80 mm dia , 22.supply of grey cast iron rod of size 100 mm dia. , 23.supply of grey cast iron rod of size 150 mm dia. , 24.supply of grey cast iron rod of size 200 mm dia. , 25.supply of bronze rod of size 50 mm dia. , 26.supply of bronze rod of size 75 mm dia. , 27.supply of aluminum rod of size 20mm dia , 28.supply of aluminum rod of size 25 mm dia. , 29.supply of aluminum rod of size 50 mm dia. , 30.supply of aluminum rod of size 75 mm dia. , 31.supply of aluminum rod , 32.supply of precipitated hardening stainless steel , 33.supply of precipitated hardening stainless steel , 34.supply of alloy steel rods , 35.supply of alloy steel rods , 36.supply of alloy steel rods , 37.supply of alloy steel rods , 38.supply of alloy steel rods , 39.supply of alloy steel rods , 40.supply of alloy steel rods , 41.supply of alloy steel rods , 42.supply of copper rod , 43.supply of copper rod , 44.supply of copper rod , 45.supply of solid graphited carbon rod , 46.supply of solid graphited carbon rod , 47.supply of solid graphited carbon rod , 48.supply of carbon steel rod , 49.supply of carbon steel rod , 50.supply of carbon steel rod , 51.supply of carbon steel rod , 52.supply of carbon steel rod , 53.supply of carbon steel rod , 54.supply of carbon steel rod total quantity : 5372...
37765310 providing and fixing of children playing equipments at various places in municipal area rishabdev ( arc ) providing and installation of multi action play system & other children playground equipments consisting of the following items the area of 8 mtr x 7 mtr and required safe area is 9 mtr x 8 mtr ( 1 ) . square deck 5 feet height the platform is made in fiber reinforced plastic. the top of platform is anti skid surface with multi colour pigmented resin .the back coat of fiber reinforced plastic is such that the mat strands are not visible and the surface is tack free. at the top of the deck there is a window canopy shade to the children playing on it. ( 2 ) .wave slide 5’ height the wave slide chute with top entry module shall be made by frp, the slide thickness thickness will be 5 mm with uv pigment to avoid colour fading.. the wave shape is given in such a manner that it will not give any jerk or bump to the rider. the chute has its end such as it causes safe landing of the child. the landing portion is horizontal with respect to the ground. ( 3 ) . frp straight slide 5 feet height the straight slide chute with top entry module shall be made by frp, the slide thickness for total will be 5 mm for both side finished ( 4 ) . rock climber 5’ ht. the rock climber is made up of fiber reinforced plastic. rocks are molded on same platform and it has gradient from the ground. the climber is supported by 25 idgi pipe at the bottom for ground support. ( 5 ) steel bridge 8’ long the steel bridge is made from 40x40x5 with crc sheet 18 gej& laminated by frp non skidchequred sheet .it has railing made from frp molded process with support of 20 nb gi pipe with the help of 80 idgi pipe and 80 x 20 nb nylon clamps. ( 6 ) . frp canopy square canopy should be made up of fiber glass reinforced plastic with 3 to 4 mm thickness with glossy finish and paint by pu paint in multy colors. ( 7 ) .frp ladder 5 feet height frp ladder should be made by fiber glass reinforced plastic with 4 to 5 mm thickness with antiskid surface. ( 8 ) . frp railing the railing is made in frp molded process .the railings are attached to each other with the help of 20 idgi pipe. ( 9 ) . hand railing hand railing should be made by 20 mm idgi pipe to proper control for children’s. there is no any sharp corner not seen on the railing. ( 10 ) . frp rindeer andfrp flower this is made from fiber glass reinforced plastics for the attraction. ( 11 ) . double swing with frp butterfly the leg support of double swing is made by 60 mm idgi pipe while the top bar is of 60 mm idgi pipes. the gi pipes are powder coated. the swing seats are made from 9 mm thick antiskid chequered reinforced rubber belt or 9 mm thick. frp seating arrangement. the ball bearings are mounted inside a specially designed clamp. ( 12 ) . spiral climber 5 feet height spiral climber made up of 25 nb gi pipes. the spiral structure is suitably bent and is kept standing with vertical 40 idgi pipe support. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments and as per direction given by eic 2 providing and installation of hanging climber: safe play area 3.4 mtr. x 2.2 mtr. dia area: 2.4 mtr. 1.2 mtr. height 2.4 mtr. it required area 2.4 mtr x 1.2 mtr& height 2.4 mtr and leg support should made up of 50 mm idgi pipe outer frame should be made by 32 mm idgi pipe in main frame joint with 20 mm idgi pipe in handrails / inner frame in dia. ladder should be made by 20 mm idgi pipe. and connected with proper fitment like welding, fastener.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge age capacity 6 12 year and as per direction given by eic 3 providing and installation of snake climber: safe play area 4.5 mtr. x 2.0 mtr. area : 3.6 x 1.0 mtr height 2.4 mtr its height 2.4 mtr. and length should be 3.6 mtr. and width should be 1.0 mtr. and made by 50 mm idgi pipe in vertical support and 32 mm nb pipe in outer frame. handrails should be made by 25 mm idgi pipe. leg support should be 50 mm idgi pipe. ladder should be made by 20 mm idgi pipe.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge age capacity 3 8 year and as per direction given by eic 4 providing and installation of swing double seater : safe play area 4 mtr. x 2.5 mtr. area: 3 mtr. x 1.5 mtr. height 2.4mtr its total required area 3 mtr. x 1.5 mtr. and height shall be 2.4 mtr. from ground level top bar of swing is made by 60mm idgi pipe. and 4 nos. of leg support pipe should be 60mm idgi pipe.top bar attach with 2 nos. of alloy steel coasting bearing with gi chain. seating arrangement of swing is made up of 10mm thick. anti skidchequered reinforced rubber belt. bearing should be covered by specially design nylon clamp. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge and as per direction given by eic 5 providing and installation of eaglesee saw: safe play area – 2.5 mtr. x 3.5 mtr. area – 1.5 mtr. x 2.5 mtr. height – 0.8 mtr. it’s required area 1.5mtr x 2.2mtr. main frame should be made by 80mm idnb centre pipe with proper fitment for installation of see saw.handle should be made by 25 mm idnb pipe. total height 0.5mm from ground level. 2 nos. of sheet made by 3 mm thick frp with proper seating arrangement grouted in cc. foundation base all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments and install by c.c. base system as per order by engineer in charge age capacity 6 12 year and as per direction given by eic 6 providing and installation of orbit climber: safe play area 3.4 mtr. x 2.2 mtr. dia area: 2.4 mtr. 1.2 mtr. height 2.4 mtr. it required area 2.4 mtr x 1.2 mtr& height 2.4 mtr and leg support should made up of 50 mm idgi pipe outer frame should be made by 32 mm idgi pipe in main frame joint with 20 mm idgi pipe in handrails / inner frame in dia. ladder should be made by 20 mm idgi pipe. and connected with proper fitment like welding, fastener.all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments.and install by c.c. base system as per order by engineer in charge age capacity 6 12 year and as per direction given by eic 7 providing and installation of circular swing : safe play area: 2.5 m x 3 m the area : 1.5 m x 2 m the leg support of this item is made up of 40 mm, while the top bar is from 50 mm powder coated gi pipes. the swing frame is made from 25 mm and 15 mm powder coated gi pipes. there are two seats provided which are made out of fiber reinforced plastic. the platform is made using chequered plate for footrest and bearing assembly is made. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments. slide should be made in a single mould piece there is no any joint in the slide.frp components should be paint by 3 layers of pu paint. and install by c.c. base system as per order by engineer in charge. all the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. the pure polyester powder coating ( oven baked ) done on the pipes extend the life of equipments. and install by c.c. base system as per order by engineer in charge age capacity 3 10 year and as per direction given by eic 8 providing and installation of platform ( gi platform ) marry go round having product area 5.0 m product height 1.1 m safe paly area 2.5 mts with age limit 5 12 year and as per direction given by eic...
37741301 bids are invited for expandable items h1 b desiccant silica gel , g2 electrode welding high alloy steel 3 point 15m , g2 electrodes welding steel armour 3 point 15mm , g2 electrodes welding steel high tensile 3 , h1 fevicol sr 998 , h1 a varnish oil g s , h1 b flux soldering paste , h1 b glue ordinary , h1 mineral jelly ammunation , g1 nails steel wire round 100 mm x 5 point 0 mm , g1 nails steel wire round 25mm x 2 mm , g1 nails steel wire round 40mm x 2 mm , h1 paint air dry br spr syn ena dark grey , h1a paint rfu fin syn br spr deep cream total quantity : 1396...
37670448 supply of 1 / 2 inch square drive ratchet type torque wrench, with chrome molybdenum alloy steel square drive, torque range 20 100 nm, along with calibration certificate ( as per specification attached ) make : groz / gedore / facom / proto or equivalent...
37412483 supply of incalloy brand 28 mm alloy steel grade 80 double chain sling oblong link ( 56 mm dia x 400 mm i / l x 250 mm i / w ) at the top and eye hook at each bottom sling jointed with indlocks, effective length : 8.0 meters, safe working load : 35 mt@90 degree angles as per drawing ic / h2 ibe / 80 / 28 8.00 m enclosed accepted make / brand mmc or similar [ warranty period: 30 months after the date of delivery ] ...
37397958 supply of wheel for track machine , alloy steel forged wheel for csm / duo / unimat 2s plasser part no. ud62.3320 india or equivalent as per cpoh drawing no. c 1410 csm and specification no. tm / cpoh / gen / wa / 021 rev 1 complete forged wheel as per rdso specification no. irsr 19 / 93. accepted make plasser or equivalent. technical details as per attached drawing & specifications with this tender document. [ warranty period: 30 months after the date of delivery ] ...
37363512 tender for supply of wear & abrasion resistant alloy steel plate hardox 450 for coal pulverisers installed at 2x660 mw csctpp, chhabra...
37359816 supply of wear and abrasion resistant alloy steel plate hardox 450 for coal pulverisers installed at 2x660 mw csctpp, chhabra , wear and abrasion resistant alloy steel plate hardox 450 in standard size: 2000mm x 6000mm as per technical specification: hardness 425 475 hbw, chemical composition c 0.21, si 0.70, mn 1.60, cr 0.50, ni 0.25, p 0.025, s 0.01, b 0.004 in following thickness , thickness 12 mm , thickness 16 mm...
37091435 supply of various types tamping arms for unimat 4s 8437 machine.acceptable make plasser or equivelent., tamping arm ( material of alloy steel casting of grade 709m40 ( fn 19 ) confirming to bs970 ( pt.ii 1970 ) hardness 220 to 230 bhn for unimat 4s 8437 machine, plasser part no. w37.1461 , id no 803013.acceptable make plasser or equivelent. [ warranty period: 30 months after the date of delivery ] , tamping arm ( material of alloy steel casting of grade 709m40 ( fn 19 ) confirming to bs970 ( pt.ii 1970 ) hardness 220 to 230 bhn for unimat 4s 8437 machine, plasser part no 4s pt. no. w37.1462 .acceptable make plasser or equivelent. [ warranty period: 30 months after the date of delivery ] ...
37089427 bids are invited for g2 3439 000222 g2 3439 000222 solder alluminium beedee kgs 150 g2 9510 000024 g2 9510 000024 steel bar carbon hot rolled round 20mm kgs 83 g2 3439 000027 g2 3439 000027 solder brazing alloy copper zinc wire 5 kgs 52 g2 9530 000090 g2 9530 000090 brass rod free cutting hexagon 20.00 mm kgs 17 g2 9510 000084 g2 9510 000084 steel bar carbon hot rolled flat 75 x 12 kgs 34 g2 3439 000149 g2 3439 000149 electrode welding high alloy steel 3.15m kgs 4...
37002655 bids are invited for supply of brass hexagonal rod 150 mm dia. , 24.supply of grey cast iron rod of size 200 mm dia. , 25.supply of bronze rod of size 50 mm dia. , 26.supply of bronze rod of size 75 mm dia. , 27.supply of aluminum rod of size 20mm dia , 28.supply of aluminum rod of size 25 mm dia. , 29.supply of aluminum rod of size 50 mm dia. , 30.supply of aluminum rod of size 75 mm dia. , 31.supply of aluminum rod , 32.supply of precipitated hardening stainless steel , 33.supply of precipitated hardening stainless steel , 34.supply of alloy steel rods , 35.supply of alloy steel rods , 36.supply of alloy steel rods , 37.supply of alloy steel rods , 38.supply of alloy steel rods , 39.supply of alloy steel rods , 40.supply of alloy steel rods , 41.supply of alloy steel rods , 42.supply of copper rod , 43.supply of copper rod , 44.supply of copper rod , 45.supply of solid graphited carbon rod , 46.supply of solid graphited carbon rod , 47.supply of solid graphited carbon rod , 48.supply of carbon steel rod , 49.supply of carbon steel rod , 50.supply of carbon steel rod , 51.supply of carbon steel rod , 52.supply of carbon steel rod , 53.supply of carbon steel rod , 54.supply of carbon steel rod total quantity : 5372...
36883592 bids are invited for 1 g2 3439 000222 solder alluminium beedee 2 g2 9510 000024 steel bar carbon hot rolled round 20mm 3 g2 3439 000027 solder brazing alloy copper zinc wire 5 4 g2 9530 000090 brass rod free cutting hexagon 20.00 mm 5 g2 9510 000084 steel bar carbon hot rolled flat 75 x 12 6 g23439 000149g2 3439 000149 electrode welding high alloy steel 3.15m total quantity : 376...
36788158 tender for supply of electrician trade tools and equipment 1 measuring steel tape 2 combination plier lnsulatedo 3 screwdnver lnsulatedr 4 screwdriver insulated electrician screwdriver thin stein insulated handle 6 heavy duty screwdriver insulated electrician screwdriver thin stem insulated handle 8 punch centre 9 knife double bladed electrician 10 neon tester, steel rwe graduated both in metric and english unit 12 hammer, cross peen with handle 13 hammer, ball peen with handle 14 pincer 15 c clamp 16 blow lamp brass 17 chisel cold 18 chisel firmer with wooden handle 19 allen key alloy steel 20 grease gun 21 pully puleer with 3 legs 22 b.arlng puller ( inside and outside ) 23 pipe vice cast iron with hardened àaw open type 24 scissors baade, ss 25 scissors blade, s3 26 crimping tool 28 wh’.cutt.randstrlpper 29 mailat hard wood 30 hamnmarextractortype 31 ( a ) hacksaw ram• 31 ( s ) hacksaw rfamea 32 ph, es long no.. insiwdw 33 pliers 11at no insdtdw 34 pliers round no insulatad 35 twmzresa 36* si ient h.avy d*y 36 b snip straight 37 lfl hand brace 3$ orli $8. twist block 39 plane cutters, etc....
36758037 bids are invited for chromium molybdenum alloy steel seamless pipe mse chromium molybdenum alloy steel seamless pipe , chromium molybdenum alloy steel seamless elbow 90 , chromium molybdenum alloy steel seamless concentric reduce , chromium molybdenum alloy steel seamless equal tee total quantity : 1090...
36477572 bids are invited for h2 cotton waste coloured , h1 b polish metal potassium , h1b napthalene balls , h1a paint rfu ad spr syn ena sky blue , h1a paint rfu matt finish olive green , h1a paint rfu fin syn ena br spr gold yellow , h1a paint rfu marking white , h1a paint rfu marking black , h1a paint rfu olive green , h1 fevicol sr 998 , h1a paint rfu priming red oxide , g2 electrode welding high alloy steel 3 point 15m , h1a paint rfu finishing general service , h2 cloth bunting navy blue 145 cm v point no2 , h2 cloth bunting scarlet , h1a paint rfu fin syn ena br spr red oxide...
36318493 supply of two legged 16mm dia alloy steel gr. 80 chain sling with o ring of 45mm dia x 245mm dia id & intermediate link of 22mm dia x 90mm x 50mm on top & connected with joining link of 18mm dia x 75mm x 40mm at both ends having forged steel eye hook at bottom chain conforming to is:6215, hook conforming to is:3822, hook opening 90mm & chain sling conforming to is:2760 1980. drg. no. 1141 / c&wl capacity 11 t, tested to proof load 22t 16mm dia x effective length = 2750 mm...
36186849 bids are invited for 1 g2 3439 000222 solder alluminium beedee 2 g2 9510 000024 steel bar carbon hot rolled round 20mm 3 g2 3439 000027 solder brazing alloy copper zinc wire 5 4 g2 9530 000090 brass rod free cutting hexagon 20.00 mm 5 g2 9510 0000840 steel bar carbon hot rolled flat 75 x 12 6 g2 3439 000149 electrode welding high alloy steel 3.15m total quantity : 376...
36186124 bids are invited for paint h2 cotton waste coloured , h1 b polish metal potassium , h1b napthalene balls , h1a paint rfu ad spr syn ena sky blue , h1a paint rfu matt finish olive green , h1a paint rfu fin syn ena br spr gold yellow , h1a paint rfu marking white , h1a paint rfu marking black , h1a paint rfu olive green , h1 fevicol sr 998 , h1a paint rfu priming red oxide , g2 electrode welding high alloy steel 3 point 15m , h1a paint rfu finishing general service , h2 cloth bunting navy blue 145 cm v point no2 , h2 cloth bunting scarlet , h1a paint rfu fin syn ena br spr red oxide total quantity : 6099...
36110608 bids are invited for paint h2 cotton waste coloured , h1 b polish metal potassium , h1b napthalene balls , h1a paint rfu ad spr syn ena sky blue , h1a paint rfu matt finish olive green , h1a paint rfu fin syn ena br spr gold yellow , h1a paint rfu marking white , h1a paint rfu marking black , h1a paint rfu olive green , h1 fevicol sr 998 , h1a paint rfu priming red oxide , g2 electrode welding high alloy steel 3 point 15m , h1a paint rfu finishing general service , h2 cloth bunting navy blue 145 cm v point no2 , h2 cloth bunting scarlet , h1a paint rfu fin syn ena br spr red oxide total quantity : 6099...
35998221 bids are invited for fabrication of cook house structure ms round pipe of size 25 mm dia , ms round pipe of size 40 mm dia , ms round pipe of size 50 mm dia , ms round pipe of size 15 mm dia , nut and bolt of size 8 mm , hollow square pipe of size 25 x 25x 3 mm , hollow square pipe of size 20 x 20 x3 mm , hollow square pipe of size 15 x 15 x 3 mm , welding rod , cutter blade 14 inch , grinding wheel disk 4 inch , cutter blade 4 inch , ss self driving screw of size 8 x 13 mm , ms angle iron of size 40 x 40 x 5 mm , gear box , cross holder , pulley , adopter , alloy steel chain of size 6 mm dia total quantity : 846...
35938781 supply and fixing of play equipment and opn gym at different park lalsot , providing and fixing of double seater swing having safe play area 4 mtr. x 2.5 mtr. the swing required total area about 3 mtr. x 1.5 mtr. and height shall be 2.4 mtr. from ground level top bar of swing is made by 60mm idgi pipe 16 gauge and 4 nos. of leg support pipe should be made of 60mm idgi pipe 16 gauge.top bar shall be attached with 2 nos. of alloy steel coating bearings with gi chain. seating arrangement of swing is made up of 9mm thick frp sheet with proper finishing work. bearing should be covered by specially design nylon clamp. the pure polyester powder coating done on the pipes to extend the life of equipments. complete set as per direction and satisfaction of engineer in charge. , sitc of multi seater see saw for which required safe play area shall be about 4mtr x1.5mtr the height of the equipment shall be about 0.8mtr.the multi seater see saw comprises of 4 nos. frp seats having thickness 4mm with proper finishing and paint finished work. the leaverconsists of 25mm idgi pipe and 80mm idgi powder coated pipe. the stand for equipment is made of 50mm idgi pipe with powder coating on complete surface. complete set as per direction and satisfaction of engineer in charge. , providingand fixing of frp made wave slide having safe play area about 4.6mtr x 0.9 mtr. thewave slide required total area 3.6 mtr x 0.6 mtr. platform height shall be 1.8 mtr. from ground level connected with leg support 60mm idgi pipe and ladder should be made by steel frame rectangular square pipe 50mm x 25mm. for safety purpose railing should be made by 25mm idgi pipe total frp slide lengthshall be 3 mtr. with 5mm thickness overall both side finishing work. all the sharp edges and corners are properly grinded to give smooth finishing.the pipes and components arepowder coated on surfaces. slide should be made in a single moulded piece having wave shape there shall be no any joint in the slide. frp components should be paint and finished. complete set as per direction and satisfaction of engineer in charge. , supply and fixing decorative fiber benches. which is made by cast iron and frp sheet plate. bench length 5 feet back height 2’5” front height 16” depth 15” and bench leg is made by cast iron. including bench leg earth work and concrete foundation m 15 grade including all material and labor charges. , open gym surf board providing and fixing of surf board of size 910mm ( length ) x 860mm ( width ) x 1400mm (height ) fabricated with a center pipe of 100mm nominal bore shall be made from “c” class g.i. pipe. the sleeve pipe shall be made of 125mm od seamless pipe with thickness of 5mm and bolted to main frame with m1 ss bolts. the bottom support shall be welded of m.s. plate of ø 250 mm & 10 mm thickness. the handle frame of 25nb shall be made from “c” class g.i. pipe. the paddle frame of 50nb shall be made from “c” class g.i. pipe supported with 70x8mm bend m.s. flat and can be replaceable. the foundation to be used for fixing should be a structure and shall be made from center pipe of g.i. of 80nb “c” class welded with m.s. round plate of ø250mm & 10mm thick. main pipe shall be supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 22 mm x 40mm crc square pipes of 3mm thickness. bushes shall be used of 70 mm outer diameter with5mm thickness. the footrests shall be made from aluminum casting material of size 320mm x 270mm x 5mm. for support to footrest of 200mm x 250mm with 3mm thickness m.s. plate shall be used. closing caps shall be made up of high quality fiber reinforced plastic material. the pins to be used shall be made up of ø35 mm sae 8620 bright material. the bearing shall be used are of “6007zz” permanent lubricatedsealed bearing of reputed brand (skf/fag). high tensile steel with galvanized nut bolts shall be used for assembly. the cerclips shall be used for assembly of a34. the powder coating shall be done with pure polyster powder of ackzonoble or berger with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of engineer in charge regarding material, shape of equipment, color of metal. , cross trainer providing and fixing of cross trainer of size 1320mm (length) x 600 (width) x 1750mm. (height) fabricated with the main frame pipes of 80nb shall be made of “c” class g.i. and pipe with single bend pipe with 250mm radius. the bottom supported of m.s. round plate of ø250mm & 10mm thick. the handle frame shall be made up of 25nb “c” class g.i. pipe. the foundation should be used for fixing is a structure and shall be made from center pipe of g.i. pipe of 80nb “c” class welded with m.s. round plate of ø250mm & 10mm thick. main pipe should be supported with 25 mm x 25 mm m.s. angles of 3 mm thickness and 20mm x 40mm and crc square pipes of 3 mm thickness. to build structure bushes to be used which shall be made from m.s. seamless pipe of 60 mm od with 5 mm thickness. the footrests shall be made from aluminum casting material of size 130mm x 310mm x 5mm thickness and mounted on m.s. plate of diameter 35mm, 25mm and 17mm shall be made up from sae 8620 bright. the bearing shall be used of “6007zz” & “6205zz” permanent lubricated sealed bearing of reputed brand (skf/fag). high tensile steel with galvanizednuts and bolts shall be used for assembly. the powder coating shall be used for assembly. bolt m8x16 mm and ny lock nut of m8 shall be made of ss 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of engineer in charge regarding material, shape of equipment, color. , thi chi spineer (2 wheel) providing and fixing of thi chi spineer (2 wheel) of size 700mm (length) x 1000mm (width) x 1280mm (height) fabricated with a center pipeof 100nb shall be made up of “c” class g.i. pipe. the handle movement round frame shall be made up from 25nb “c” class g.i. pipe. the foundation should be used for fixing is a structure and shall be made from center pipe of g.i. of 80nb “c” class, welded with m.s. round plate of ø250mm & 10mm thick. main pipe shall be supported with 25mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. closing caps shall be made up of high quality fiber reinforced plastic materials. the pins to be used shall be made up of ø25mm of sae8620 bright material. the bearing shall be used of “6205zz” & “6205zz” permanentlubricated sealed bearing of reputed brand (skf/fag). high tensil s.s. nut boltsshalll be used for assembly. foundation cover closing cap shall be made from frp material with 0.7 mm thickness. the cerclips used for assembly shall be of a24 and a11. the nylon bush shall be used for handle knob. the powder coating shall be done with pure polyester powders from ackzonoble of berger paints with 60 to 70 micron thickness. bolt m8x16mm and nylock nut of m8 shall be made of ss 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of engineer in charge regarding material, shape of equipment, color. , seated puller providing and fixing of seated puller of size 1900mm (length) x 740mm (width) x 1920mm (height) fabricated with a center pipe is of 100nb shall be made from “c” class g.i. pipe. bottom supported of m.s. round plate of ø250 mm & 10mm thickness shall be welded. all linkages shall be made up of 25nb “c” class g.i. pipe. the handle frame on 32nb “c” class g.i. pipe. the seat frame of 32nb “c” class g.i. pipe, to build structure bushes to be used which shall be made from seamless pipe of 60mm od and 5mm thickness as well as 60mm diameter solid bar bush shall be used. the foundation should be used for fixing is a structure and shall be made from center pipe of g.i. of80nb “c” class pipe welded with m.s. round plate of ø250mm & 10mm thick. main pipe shall be supported with 25mm x 25mm m.s. angles of 3mm thickness and 20mmx 40 mm crc square pipes of 3mm thickness. foundation cover closing cap shall be made from frp material. the seats and back rests to be fitted on the outer frames shall be made up of m.s. sheet of sizes 330mm x 300mm x 2 mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edged.closing caps be made up of high quality fiber reinforced plastic. , sit up board double providing and fixing of sit up board double of sizes 1760mm( length) x 1140mm (width) x 660mm ( height) fabricated with the main frame of 25mm nb shall be made from “c” g.i. pipe. frp sheet of 3mm thickness shall be moulded on main frame. the remaining frame of the sit up board of 32mm nb shell be made from “c” class g.i. pipe. the powder coating shell be done with pure polyester powder ackzonoble or berger paints with 60 to 70 micron thickness. the foundation should be used for fixing is a structure and shell be made from center pipes of g.i. of 80nb “c” class welded with m.s. round plate of ø250mm & 10mm thick. main pipe shall be supported with 25mm x 25mmm.s. angles of 3mm thickness and 20mm x 40mm crc square pipes of 3mm thickness, all complete per drawing , design, directions and approvel of engineer in charge regarding material, shape of equipment, color ( of metal, seat and pedal), and fixing of equipment etc. , pommel horse providing and fixing of pommel horse of sizes 2150mm ( length) x 800mm (width) x 800mm ( height) fabricated with the main frame of 80nb & 50nb shall be made from “c” class g.i. pipe. the handle frame of 32nb shall be made from “c” class g.i. pipe. 40mm x 40mm crc square pipes frame shall be plased on the 25mm x 25mm x3mm m.s. l angle with 60 x 10m thickness flat should be used for support. closing caps shall be made up of high quality fiber reinforced plastic material. hightensile steel with galvanized nuts and bolts shall be used for ammembly. the powder shell be done with pure polyester powder ackzonoble or berger paintswith 60 to 70 micron thickness, all complete as per drawing, design, directions and approvel of engineer in charge regarding material, shape of equipment,color ( of metal, seat and pedal ), and fixing of equipment etc. , seating and stainding twister providing and fixing ofseated & stainding twister of size 1700mm( length) x 540mm (width) x 1250mm (height) fabricatied with a center pipe of 100mm nb shall be made from “c” class g. i. round pipe. the m.s. round plate ø250mm & 10mm thickness shallbe welded at bottom. handle and bottom sleeve pipe of 125mm od with thickness 5mm should be provided foreasy assembly, replacement and maintenance. the bottom frame of seating and staindingtwister of 32 nb, 50 nb, & 25 nb shall be made from “c” class g.i. pipe.the handle frame of seating and stainding twister of 25nb and foot restingframe of seating side shall be made from “c” class g.i. of 25mm nb the foundation should be used for fixing is a structure and shall be made from center pipe of g.i.of 80nb “c” class, welded with m.s. round plate of ø250mm & 10mm thick. main pipe shall be supported with 25mm x 25mm m.s. angles of 3mm thickness and 20mmx 40 mm crc square pipes of 3mm thickness. the twister plate to be fitted on the bottom frame shall be made up m.s. round plate of size 300mm dia meter and 10mm thickness. closing caps shall be made up of high quality fiber reinforced plastic material. the pins to be used be shallbe made up ofø35mm sae 8620 bright material. the bearingshall be made of “6205zz” permanent lubricated sealed bearing reputed brand (skf/fag). high tensile steel with galvanized nuts and bolts shall be used for assembly. the powder coatingshall be done by purepolyester powder of berger paint with 60 to 70 micron thickness all complete as per drawing, design, directions and approvel of engineer in charge. , push up bar .dimensions : 1220mm ( length) x 550mm (width) x 1700mm ( height) . safe area : 2 mtr. x 1 mtr. push up bar equipment made from “c” class g.i. pipe of different nb. nb stands for nominal bore sizes i.e. internal diameter of pipe in milimeters. the main frame “c” class g.i. pipe. the m.s. round plate of ø250mm and 10mm thickness is welded at bottom . the handle frame of 25nb made from “c” class g.i. pipe. the foundation used for fixing is a structure and made fromcenter pipe of g.i. of 80nb “c” class welded with m.s. 12 gpp round plate of ø250mm &10mm thick. main pipe supported with 25mm x 25mm m.s. angels of 3mm thickenessand20mm x 40mm crc square pipes of 3mm thickness. closing cap are made upof high quality fiber reinforced plastic material. foundation cover closing cap is made from frp materials with 0.7mmthickness. heightensil steel with galvanizednuts and bolts are used for assembly. the powder done withpure polyester powders of ackzonoble or berger paints with 60 to 70 micron thickness....
35929275 supply of tyre defect gaugetyre defect gauge,tyre defect gauge for bg , model tdg 1, as per plate 38 rule2.8.4 of irca, made of 3mm thick hard alloy steel plate. make pie or similar. with oem,s original calibration certificate. [ warranty period: 12 months after the date of delivery]...
35908464 supply of various types tamping arms for unimat 4s 8437 machine.acceptable make plasser or equivelent.various types tamping arms for unimat 4s 8437 machine.acceptable make plasser or equivelent.,tamping arm( material of alloy steel casting of grade 709m40(fn 19) confirming to bs970(pt.ii 1970) hardness 220 to 230 bhn for unimat 4s 8437 machine, plasser part no. w37.1461 , id no 803013.acceptable make plasser or equivelent. , tamping arm( material of alloy steel casting of grade 709m40(fn 19) confirming to bs970(pt.ii 1970) hardness 220 to 230 bhn for unimat 4s 8437 machine, plasser part no 4s pt. no. w37.1462 .acceptable make plasser or equivelent....
35799385 supply of 1 / 2 inch square drive ratchet type torque wrench, with chrome molybdenum alloy steel square drive, torque range: 20 100 nm, along with calibration certificate...