Indian Army - Rajasthan

40601684 bids are invited for electric ceiling fan with bldc motor as per is 374 (v2) (q2) , propeller type ac ventilating fans exhaust fans (v2) as per is 2312 (q2) , air circulator type electric fan as per is 2997 (q3) total quantity : 350...

Indian Army - Rajasthan

40542560 bids are invited for wall mounting fan air circulator (q3) total quantity : 10...

Indian Air Force - Rajasthan

40522518 bids are invited for air circulator type electric fan as per is 2997 ( q3 ) total quantity : 10...

Military Engineer Services - Rajasthan

39768360 provision of repair shed for ‘c’ veh with hard standing with 2 ton travelling trolley at fd wksp coy in army area under ge ( army ) no. 01 jodhpur; 1 surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in any type of soil complete all as specified and as directed. 2 m&l for hardcore of gaugeexceeding 63 mm but not exceeding 100 mm of brokenstone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, compaction and consolidation with power roller, complete all as specified and as directed. 3 excavation in post holes each not exceeding 0.5 cu.m, getting out in any type of soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed. 4 m&l cement concrete 1:3:6 type c 1 by using 20mm graded crushed stone aggregate as in foundation, filling, mass concrete, embedded concrete for fencing post hole, including necessary form work complete all as specified and as directed. 5 s&f steel work in tubular trusses including special shaped washers etc complete using erw or induction butt welded tubes confirming to is:1161 1979 grade st 240 complete all as specified and as directed. 6 m&l for mild steel work confirming to fe 410, grade e 250 , quality a, as in roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc. etc complete all as specified and as directed. 7 s&f plates ( plain or / mdsplate chequered ) channels square cut or notched ( ordinary and counter sunk ) forming holes with riveted bolted or welding attachement 8 m & l for preparing new steel surfacesof any descriptionexc 10 cm in width, priming with red oxide and applied two coat of synthetic enamel paint complete all as specified and directed. 9 s&f prepainted galvalume aluminium zinc coating gi based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and as directed. 10 m&l 100 mm thick pcc 1:4:8 type d2 using 40mm graded crushed stone aggregate for sub base as in floor complete all as specified and as directed . 11 m & l for cement concrete work in pavement / hard standing of flexural strength 40 kg / per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed 12 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil all as speicfied and directed. 13 m&l pcc 1:4:8 type d2 by using 40mm graded stone aggregate as in foundations filling and mass concrete complete all as specified and directed. 14 m&l for squarred rubble walling jodhpur type regular coursed well bonded , bedded and solidly hearted built in cement mortar 1:6 complate all as specified and directed. 15 extra over squared rubble stone walling jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete to squared rubble walling, regular coursed, jodhpur typeall as specified and directed. 16 m&l for keyed pointing to square rubble masonryjodhpur type regular course in cm 1:3 all as specified. 17 m&l for preparation of new plastered or un plastered surfaces of walls and applying two coats of cement base paint over a coat of chalk white, complete all as specified and as directed. 18 m&l for pcc 1:2:4 type b1 mix using 20mm graded stone aggregate as in hold fast iron fixing, coping, chamfered edgesincluding necessary form work all asspecified. 19 removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and directed. 20 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. all as specified and directed. 21 s&f expanded metal, n exc 4 kg cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members 22 supply and lay in trenches / on wall / on pole / in duct / through protection pipe, xlpe insulated, screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables heavy duty lt cable, 1100 volts grade with aluminium conductor cross sectional area16 sqmm 4 core size including retrieving / taking out / taking down old unserviceable cable from duct / trenches / pipes / pole / wall etc. including brick cover and protection pipe and disconnecting the connections.note: excavation andearth work, sand cushioning, pcc cable cover and protection pipe etc. shall be measured and paid for separately. 23 m&l for dry clean fine river sand as in sand cushioningto underground cable including punning down ofsand layer all as specified and directed. note : punnedthickness shall only be measured and paid. 24 supplying and laying un reinforced precast concrete cable cover, class lv, type 1, flat, size 250x150mm x40 mm 25 m&l for galvanised steel tubing, light grade, for protection of cable, laid in trenches / road crossing / floor or fixed to pole / wall with all fittings, of size 40 mm bore. 26 m & l for surface point wiring complete with multistranded copper conductor 1.5 sqmm pvc insulated unsheathed single core frlsh cable 1100 volt grade, confirming is 694 & colour code in conduit system of wiring, drawn through in and includingnon metalicpvcsurface conduit of size 20 / 25 mm or med grade as required as site, totallysurface for floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings such as tee / elbow / sockets / junction boxes / inspection covers etc of heavy grade, isi marked and surface pvc gang box.wodden box for mounting switch and sockets , for mounting of switches, sockets fan regulators etc incl 1.5 sqmm frlsh pvc insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, suitable for one light / fan point controlled by one, one wayswitch, complete all as specified and directed. 27 all as per item no 26.00 here in above but with 2.5 sq mm single core multistanded copper conductor cable for 3 pin 16 amp socket outlet on independent board . 28 s&f socket outlet 2 in 1, 6 pin, 6 and 16 amp flush type, 230 volts, isi marked complete all as specified and directed. 29 s&f switch piano flush type single pole one way 16 amp, 230 volts, isi marked complete all as specified and directed. 30 s&f switch piano type, single pole, one way, 5 / 6 amps, 230 volts, isi marked complete all as specified and directed. 31 s&f ceiling rose, three terminals, bakelite body, 230 volts, isi marked complete all as specified and directed. 32 supply and fixing as mcb db spn ( double door ) 4 ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wallall as specified and directed by the engr in charge. 33 s&f mcb, b curve type, 10 ka, 6 to 40amp, spn with over load and short circuit protection, isi marked complete all as directed. 34 s&f mcb, b curve type, 10 ka, 6 to 32 amp, single pole with over load and short circuit protection, isi marked complete all as directed. 35 supply and fixing led flood light 70 watt 230 v ac outdoor type with thermal management in multiple optics and equipped with ip66 protection, with impact and corrosion resistant complete with driver and lamp 36 s&f bldg security ledlight luminaire of 35 watts having ip 65 protection fiting made out of pressure die cast aluminium housing, operating voltage 140 270 volts with in built surge protectore, toughened glass with and including sutaible size ofgi bracket including drilling holes, nuts & bolts 2 coats of red oxide primer on gi pipe and fixing with wall security light on building wall connecting cable complete all as directed. 37 s&f air circulator wall fans 230 v single phase oscillating 450 mm sweep , copper winding, heavy duty motor, suitable for wall / pole / pipe / piller mounting all as directed. 38 s & fsub main wiring with two runs of pvc insulated but unsheathed multi stranded copper conductor frlsh cable 1100 volt grade of size 4 sqmm and one run of 4 sqmm single core pvc insulated but unsheathed multi stranded copper conductor frlsh cable ( phase red, neutral black, earth green ) 1100 volt grade as earth lead duly coneected with earth dolly drawn through in and includingnon metallic pvc conduit of size 25 mm dia ( external ) with wall thickness not less than 1.8 mm, isi marked surface on wall includingaccessories like bends, tees junction boxes, etc fixed in wall or ceiling etc. complete as directed by engineer in charge.note: two runs of cable with one run of earth wire and pvc conduit shall be measured & paid for as one length. 39 materials and labour for earthingcomplete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised strip of size 25 x 4mmby means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 40 mm bore ( medium grade ) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe ( light grade ) , wire mesh, charcoal or coke and common salt in alternate layer of 15cm ( compacted thickness ) all round the earth electrode, concrete earth pit in pcc ( 1:3:6 ) type c 1 ( with 20mm graded aggregate ) , 50mm thick precast rcc ( 1:2:4 ) cover slab ( re inforced with 8mm dia tmt bar @ 15 cm c / c bothways and suitable handle made of 10mm dia ) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate no. 3 of mes schedule part i ( 2009 ) complete including testing on completion all as specified and as directed by the engr in charge.note: ( i ) item includes the cost of 7.5 metre gi pipe for protection of earth lead. ( ii ) item includes the cost of 7.5 metre gi earth lead. 40 s&fand testing factory made sheet metal enclosurefor mcb db tpn 4 way 415 volt with double door, ip 43 protectionduly withfixed in wall / concealed in wall / surface on wall / pile / piller complete and making good disturbed surfaces of wall, floor etc including electric wire connectionall as directedby engineer in charge. 41 s&f mcb tpn, c curve type , 415 volts, 32 amps with over load and short circuit protection, isi marked complete all as directed. 42 supply, install , erection, testing and commissioning eot crane 2 ton capacity comprising following and notes and precommissioning factory test as per is complete all as directed by eic 43 type: single girder eot crane 44 swl 2t 45 class & duty class ii as per is: 3177 & 807. 46 span 9 mtr. approx. 47 height of lift 5 mtr. 48 bay length 20 mtr. 49 speed: a ) hoisting 0 3m / min 50 b ) cross travel 0 15m / min 51 c ) long travel motorized 52 motors: all motors are sq, cage., crane duty, 40% cdf, ip 55, 150 st. / hr., cl. b / f insulation, foot mounted of bbl / crompton / hindustan make as per is:325. 53 a ) hosting 3.0hp sq cage 54 b ) cross travel 0.5hp sq cage x 1nos. 55 c ) long travel 1 hp sq cage 56 brake: a ) hoisting dc disc type 57 b ) cross travel dc disc type 58 c ) long travel dc disc type 59 limit switch shall be provided for all motion. 60 gears : a ) hoisting hardened, horizontal, helical, splash lubricated 61 b ) cross travel premium / hindustan make gear box with warm gear / bonifilioli 62 ct wheel dia 190mmx100, 22208 l block 63 c ) long travel premium / hindustan make gear box with warm gear / bonifilioli 64 power supply : 415 volts + / 10%, 3 phase 50 c / s ac 65 control voltage 110 volts 66 control panel : all contactor / overload relays push button station etc. shall be operated make like siemens / schneider 67 wire rope : usha martein make 12 mm / 6x36 fmc, fiber core180 kg / mm sq. as per is :2266 68 no. of fall: 4 falls 69 hook : with thrust bearing plain shank type as per is:3815 / 4637 / 70 rope drum : seamless pipe 71 lt wheel size. : 250 dia with 90 width 72 lt rail recommended: 40x40 square rail 73 plat form: small size platform will be provided in lt side for maint. purpose. 74 operation: pendent controlled 75 painting: golden yellow synthetic enamel / dark blue / navy blue. 76 notes :1 ) rate are demmed to be included for testing at site by oem / contractor in presence of user, je e / m, age e / m, and ge, also realease of payment will be restricted as 10 % or as certain percentage decided by ge. after satisfactory testing full payment will be release. precommisioning test will be carrired out at manufacturer permisses / companyas per is.2 ) oem / contractorshall provide drawing for gridder foundation, to be fabrication at time of vehicle shederrection.3 ) gallentry portion for long travell ( forward & backward ) of eot crane is considered in the b / r i portion for excution4 ) oem shall prvide drawings for grider foundation, to be fabrication at time of serviceable shed....

Directorate of Local Bodies - Rajasthan

38455369 supply of electrical item bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan, wall mounting oscillating type air circulator, 450 mm sweep with wall mounting and three speed regulator, 6 a one way switch , 16 amp. 1 module switch with led indicator , socket, non modular switch, mcb, single pole, led direct retrofit bulb, led tube without batten, 2 led tube shape fixture 9 / 10 w ( polycarbonate base ) ....

North Western Railway - Rajasthan

38352575 supply of heavy duty bldc air circulator fan 600 mm sweep, 1300 rpm, watt 120 140, wall mounting type should have speed adjustments, suitable to work on 200 260 v, air delivery conforming to is2997 / 1964 with two year warranty make airzon, havells, bajaj, atemberg or similar [ warranty period: 24 months after the date of delivery ] ...

Military Engineer Services - Rajasthan

38038642 tender for repair / maint of ceiling fan, exhaust fan, air circulator fan, wall mounting fan and connected internal accessories of otm accn...

North Western Railway - Rajasthan

37923069 supply of heavy duty bldc air circulator fan 600 mm sweep, 1300 rpm, watt 120 140, wall mounting type should have speed adjustments, suitable to work on 200 260 v, air delivery conforming to is2997 / 1964 with two year warranty make airzon, havells, bajaj, atemberg or similar [ warranty period: 24 months after the date of delivery ] ...

Military Engineer Services - Rajasthan

37452132 repair/maintenance of summer appliance i.e. water cooler, desert cooler, ac, refrigerator and deep freezers and repair/overhauling of ceiling fans, exhaust fans, geysers, air circulator, fresh air fan etc at military station kanasar....

Military Engineer Services - Rajasthan

37378626 repair / replacement of ceiling fans, exhaust fans, wall mounted fans, pedestal fans and air circulators along with allied e / m works at af stn suratgarh...

Medical Health And Family Welfare - Rajasthan

36433514 electrical work in the construction of phc building at badka ( laxmangarh ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 163 4 kg...

Medical Health And Family Welfare - Rajasthan

36432928 electrical work in the construction of phc building at duhar chougan ( thanagazi ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 163 4 kg...

Medical Health And Family Welfare - Rajasthan

36432910 tender for electrical work in the construction of phc building at basai jogiyan ( thangagazi ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr ....

Public Works Department - Rajasthan

36408724 tender for electrical work in govt. srg hospital jhalawar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surface isi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box , 10 a modular switch, modular faceplate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required. for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 2 short point ( up to 3 mtr. ) 3 medium point ( up to 6 mtr. ) 4 long point ( up to 10 mtr. ) 5 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) of approved make on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface 2 no. moulded virgin materialupvcmodular box , 2 nos 10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 6 medium point ( up to 6 mtr. ) 7 long point ( up to 10 mtr.. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box, modular 10a switch, 3 / 5 pin6 amodular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 11 25 mm x 12 mm 12 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 13 2 x 2.5 sq. mm. + 1x1.5sqmm 14 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 15 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 16 3.0 mm thick 17 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 18 single pole mcb ( with b / c curve tripping characteristics ) 19 6 a to 32 a rating 20 double pole mcb ( with b / c curve tripping characteristics ) 21 40 a rating 22 four pole mcb ( with b / c curve tripping characteristics ) 23 50 / 63 a rating 24 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 25 metal door ( single phase ) ik 09 and ip 43 with metal end box 26 4 way ( 4+2 ) 27 p & f isi marked ( is:3854 ) 6 amp. flush type non modular switchwith cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 28 p & f isi marked ( is :3854 ) 16 amp. flush type non modular switch cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 29 providing & fixing ofof 3 / 5 pin 6 amp. flush typenon modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 30 providing & fixing of3 / 6 pin 16 amp flush type non modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 31 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 32 4 pole mccb with thermal magnetic release 33 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 34 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 35 10.0 sq. mm 36 2 core 37 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 38 up to 457 mm size 39 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 40 300 mm sweep ( 900 / 1400 rpm ) 41 380 mm sweep ( 900 / 1400 rpm ) 42 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 43 up to 380 mm size 44 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 45 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 46 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 47 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 48 recessed mounting 49 minimum lumen output 1300 lm 50 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 51 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 52 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 600 mm sweep wall mountingwith minimum air delivery 270 cum. / minute...

Public Works Department - Rajasthan

36407422 tender for electrical work in govt. janana hospital jhalawar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surface isi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box , 10 a modular switch, modular faceplate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required. for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 2 short point ( up to 3 mtr. ) 3 medium point ( up to 6 mtr. ) 4 long point ( up to 10 mtr. ) 5 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) of approved make on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface 2 no. moulded virgin materialupvcmodular box , 2 nos 10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 6 medium point ( up to 6 mtr. ) 7 long point ( up to 10 mtr.. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box, modular 10a switch, 3 / 5 pin6 amodular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 11 25 mm x 12 mm 12 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 13 2 x 2.5 sq. mm. + 1x1.5sqmm 14 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 15 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 16 3.0 mm thick 17 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 18 single pole mcb ( with b / c curve tripping characteristics ) 19 6 a to 32 a rating 20 double pole mcb ( with b / c curve tripping characteristics ) 21 40 a rating 22 four pole mcb ( with b / c curve tripping characteristics ) 23 50 / 63 a rating 24 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 25 metal door ( single phase ) ik 09 and ip 43 with metal end box 26 4 way ( 4+2 ) 27 p & f isi marked ( is:3854 ) 6 amp. flush type non modular switchwith cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 28 p & f isi marked ( is :3854 ) 16 amp. flush type non modular switch cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 29 providing & fixing ofof 3 / 5 pin 6 amp. flush typenon modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 30 providing & fixing of3 / 6 pin 16 amp flush type non modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 31 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 32 4 pole mccb with thermal magnetic release 33 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 34 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 35 10.0 sq. mm 36 2 core 37 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 38 up to 457 mm size 39 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 40 300 mm sweep ( 900 / 1400 rpm ) 41 380 mm sweep ( 900 / 1400 rpm ) 42 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 43 up to 380 mm size 44 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 45 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 46 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 47 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 48 recessed mounting 49 minimum lumen output 1300 lm 50 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 51 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 52 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 600 mm sweep wall mountingwith minimum air delivery 270 cum. / minute...

North Western Railway - Rajasthan

36185904 supply of heavy duty bldc air circulator fan 600 mm sweep, 1300 rpm, watt 120 140, wall mounting type should have speed adjustments, suitable to work on 200 260 v, delivery minimum of 500 cmm, conforming to is 2997 / 1964 with two year warrenty...

North Western Railway - Rajasthan

36143978 supply of heavey duty bldc air circulator fan 600 mm sweep, 1300 rpm, watt 120 140 , wall mounting type should have speed adjustments, suitable to work on 200 260 v, delivery minimum of 500 cmm, confirming to is 2997 / 1964 with two year warranty , accepted make airzon, havells, bajaj, atomberg or equivalent. [ warranty period: 30 months after the date of delivery ] ...

North Western Railway - Rajasthan

36124746 supply of heavy duty bldc air circulator fan 600 mm sweep ( 24 inch ) , 1300 rpm ( + / 5% ) , watt 120 140w, wall mounting type should have speed adjustments, suitable to work on 200 260v ac, 50 hz supply, air delivery: minimum of 500 cmm, conforming to is 2997 / 1964 with two years warranty....

North Western Railway - Rajasthan

35756693 supply of heavy duty bldc air circulator fan 600 mm sweep ( 24 inch ) , 1300 rpm ( + / 5% ) , watt 120 140w, wall mounting type should have speed adjustments, suitable to work on 200 260v ac, 50 hz supply, air delivery: minimum of 500 cmm, conforming to is 2997 / 1964 with two years warranty....

Military Engineer Services - Rajasthan

35080943 tender for repair and maintenance of ceiling fans, air circulators, exhaust fans, geyser and solar water heater at zone iii area under ge (s) jaipur...

Malaviya National Institute Of Technology - Rajasthan

33037471 purchase of electrical maintenance item for estate section mnit jaipur 1. 6 amp. flush type switch ( make ssk ( topline ) , anchor ( penta ) , elle, hi fi, vinay ( clair 30 ) , leader ( euro ) , precision ( prime ) , cona ( wawa ) , kolors ( kubik / kom ) , antex ( lk ) ) each 500 2. 16 amp. flush type switch ( make ssk ( topline ) , anchor ( penta ) , elle, hi fi, vinay ( clair 30 ) , leader ( euro ) , precision ( prime ) , cona ( wawa ) , kolors ( kubik / kom ) , antex ( lk ) ) each 500 3. 6amp bell push flush type ( make ssk ( topline ) , anchor ( penta ) , elle, hi fi, vinay ( clair 30 ) , leader ( euro ) , precision ( prime ) , cona ( wawa ) , kolors ( kubik / kom ) , antex ( lk ) ) each 50 4. 6a twin control switch flush type ( make ssk ( topline ) , anchor ( penta ) , elle, hi fi, vinay ( clair 30 ) , leader ( euro ) , precision ( prime ) , cona ( wawa ) , kolors ( kubik / kom ) , antex ( lk ) ) each 50 5. 3 pin 6 amp. flush type socket ( make ssk ( topline ) , anchor ( penta ) , elle, hi fi, vinay ( clair 30 ) , leader ( euro ) , precision ( prime ) , cona ( wawa ) , kolors ( kubik / kom ) , antex ( lk ) ) each 500 6. 3 / 6 pin 16 amp flush type socket ( make ssk ( topline ) , anchor ( penta ) , elle, hi fi, vinay ( clair 30 ) , leader ( euro ) , precision ( prime ) , cona ( wawa ) , kolors ( kubik / kom ) , antex ( lk ) ) each 500 7. 6 amp surface type ceiling rose ( make ssk, anchor, precision, vinay, cona, elle, kolors, north west ) each 100 8. 6 amp bakelite batten / angle holder ( make ssk, anchor, precision, vinay, cona, elle, kolors, north west ) each 300 9. 6 amp bakelite unbreakable 3 pin plug top ( make ssk, anchor, precision, vinay, cona, elle, kolors, north west ) each 50 10. 16 amp bakelite unbreakable 3 pin plug top ( make ssk, anchor, precision, vinay, cona, elle, kolors, north west ) each 50 11. flush type 120 / 280 watt rotary step fan regulator ( make ssk, anchor, precision, vinay, cona, elle, kolors, north west ) each 400 12. fr pvc insulated & unsheathed flexible copper conductor isi marked ( is:694 ) of 1.1 kv grade. 1 x 1.0 sq.mm ( make rr kabel , national, finolex, polycab ) mtr. 8100 13. fr pvc insulated & unsheathed flexible copper conductor isi marked ( is:694 ) of 1.1 kv grade. 1 x 1.5 sq.mm ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) mtr. 8100 14. fr pvc insulated & unsheathed flexible copper conductor isi marked ( is:694 ) of 1.1 kv grade. 1 x 2.5 sq.mm mtr. 6300 ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) 15. fr pvc insulated & unsheathed flexible copper conductor isi marked ( is:694 ) of 1.1 kv grade. 1 x 4.0 sq.mm ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) mtr. 2700.0 16. fr pvc insulated & unsheathed flexible copper conductor isi marked ( is:694 ) of 1.1 kv grade. 1 x 6.0 sq.mm ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) mtr. 1350.0 17. 1.5 sq.mm 3 core copper round cable ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) mtr. 800.0 18. 2.5 sq.mm 3 core copper round cable ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) mtr. 600.0 19. supply of pvc insulated submersible cable confirming to is: 694 with flexible copper conductor 4.0 sq.mm 3 core copper flat ( make rr kabel , national, finolex, rallison, delton, eon ( indoasian ) , kei, terexal, plaza, anchor, l & t, standard, paramount, empire, orient cab, orbit, hpl, unicab, polycab, havells, diatron ) mtr 250.0 20. capacitors 2.5 mfd 250 v ( make: philips, bajaj, havells, cg, osram, usha, punsumi, priya, capital, jec, amcap, concap, epcos, l&t, ge, neptune, abb, schneider ) each 500.0 21. capacitors 4.0 mfd 250 v ( make: philips, bajaj, havells, cg, osram, usha, punsumi, priya, capital, jec, amcap, concap, epcos, l&t, ge, neptune, abb, schneider ) each 125.0 22. supply of starter for existing fluorscent lamp. ( fsu ) ( make:philips, bajaj, cg, wipro, surya, havells, hpl, ge, pierlite, osram ) each 350.0 23. bulb ( gls ) 100 watts ( make:philips, bajaj, cg, wipro, surya, havells, sylvania, osram ) each 150.0 24. supply of medium duty rigid pvc conduit 20mm ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) mtrs 900.0 25. supply of pvc nipple ( suitable for 20 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) nos. 540.0 26. supply of pvc bend ( suitable for 20 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) nos. 150.0 27. supply of pvc 4 way junction box ( suitable for 20 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) nos. 150.0 28. supply of g.i. saddle ( suitable for 20 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) packet ( 100 pcs in each ) 10.0 29. supply of pvc saddle ( suitable for 20 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, packet ( 100 pcs 10.0 richa ) in each ) 30. supply of medium duty rigid pvc conduit 25mm ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) mtrs 900 31. supply of pvc nipple ( suitable for 25 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) nos. 540 32. supply of pvc bend ( suitable for 25 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) nos. 150 33. supply of pvc 4 way junction box ( suitable for 25 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) nos. 150 34. supply of g.i. saddle ( suitable for 25 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) packet ( 100 pcs in each ) 10 35. supply of pvc saddle ( suitable for 25 mm pvc conduit ) ( make: akg, bec, precision, polypack, shrinath, polycab, plaza, dauphin, richa ) packet ( 100 pcs in each ) 10 36. supply of 20 mm x 12 mm pvc casing capping ( make: akg, prestoplast, precision, polycab, dauphin, richa, shrinath, polypack, plasoduct, sanco, modi ) mtrs 300 37. supply of pvc bend l ( suitable for 20 mm x 12 mm pvc casing capping ) ( make: akg, prestoplast, precision, polycab, dauphin, richa, shrinath, polypack, plasoduct, sanco, modi ) nos. 90 38. supply of 25 mm x 12 mm pvc casing capping ( make: akg, prestoplast, precision, polycab, dauphin, richa, shrinath, polypack, plasoduct, sanco, modi ) mtrs 300 39. supply of pvc bend l ( suitable for 25 mm x 12 mm pvc casing capping ) ( make: akg, prestoplast, precision, polycab, dauphin, richa, shrinath, polypack, plasoduct, sanco, modi ) nos. 90 40. carbon steel dry wall screw, size: 6x38 mm ( isi marked ) packet ( 800 pcs in each ) 25 41. wall anchor fasteners, size 10 mm x 50mm ( isi marked ) each 150 42. wall anchor fasteners, size 12 mm x 50mm ( isi marked ) each 150 43. electrical insulation self adhesive pvc tap roll ( isi marked ) each 1000 44. roll plug ( 6 mm pvc ) ( isi marked ) packet ( 100 pcs in each ) 200 45. single pole mcb 10 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 150 46. single pole mcb 16 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 300 47. single pole mcb 25 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 300 48. single pole mcb 32 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 150 49. double pole isolator 40 a rating each 75 ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) 50. double pole isolator 63 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 50 51. four pole isolator 40 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 50 52. four pole isolator 63 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 100 53. four pole isolator 100 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 75 54. supply of 240 / 415 v residual current circuit breaker conforming to is:12640:1988 / iec 61008. four pole 30 ma sensitivity 25 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 25 55. supply of metal clad industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in sheet steel enclosure ( without mcb ) single phase / double pole ( three pin ) 32 a ( make : siemens, l&t, havells, standard, hpl, ge, legrand, schneider, abb, bch, indoasian, c&s ) each 70 56. supply of metal clad industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in sheet steel enclosure ( without mcb ) three phase / four pole 30a 32 a ( make : siemens, l&t, havells, standard, hpl, ge, legrand, schneider, abb, bch, indoasian, c&s ) each 35 57. supply of fluorscent tube rod t5 lamps 28 watts ( make : cg, bajaj, wipro, surya, havells, hpl, ge, pierlite, halonixphilips, cg, bajaj, wipro, surya, havells ) each 250 58. supply of 100 mm x 175 mm and 10 mm thick teak wood board duly antitermite treated, varnished each 150 59. supply of 3 mm thick paper phenolic resin bonded laminates for boxes / frames to cover the wooden box of 100mm x 175 mm and provide the holes to fit one 16 a switch and one 16 a socket. each 150 60. supply of following modular accessories made out of unbreakable and fire retardant poly carbonate ( material required for maintenance of existing accessories ) a. 60.1 6 a one way switch ( make: schneider electric opale x1001 wh ) each 400 b. 60.2 6 a 3 pin shuttered socket ( make: schneider electric opale x2005 wh ) each 250 c. 60.3 6 a two way switch ( make: schneider electric opale x1002 wh ) each 50 d. 60.4 6a bell push switch ( make: schneider electric opale x1005 wh ) each 50 e. 60.5 16 a one way switch ( make: schneider electric opale x1101 wh ) each 400 f. 60.6 16 a 5 / 6 pin shuttered socket ( make: schneider electric opale x2103 wh ) each 250 g. 60.7 25 a shuttered socket ( make: schneider electric opale x2207 wh ) each 150 h. 60.8 32 amp. 2 module switch ( make: schneider electric opale aakx1232 wh ) each 150 i. 60.9 5 step fan regulator 2 module ( make: schneider electric opale x3200 wh ) each 150 j.60.100 supply of mounting grid plates with cover plates 4 module ( make: schneider electric suitable for opale accessories ) each 20 k.60.11 supply of mounting grid plates with cover plates 6module ( make: schneider electric suitable for opale accessories ) each 20 l.60.12 supply of mounting grid plates with cover plates 12 module ( make: schneider electric suitable for opale accessories ) each 20 m. 60.13 6 a one way switch ( make: legrand mylinc ) each 400 n.60.14 6 a 3 pin shuttered socket ( make: legrand mylinc ) each 150 o.60.15 16 a one way switch ( make: legrand mylinc ) each 200 p.60.16 16 a 5 / 6 pin shuttered socket ( make: legrand mylinc ) each 200 q.60.17 5 step fan regulator 1 module ( make: legrand mylinc ) each 150 r.60.18 supply of mounting grid plates with cover plates 4 module ( make: legrand suitable for mylinc accessories ) each 10 s.60.19 supply of mounting grid plates with cover plates 6module ( make: legrand suitable for mylinc accessories ) each 10 t. 6020 supply of mounting grid plates with cover plates 12 module ( make: legrand suitable for mylinc accessories ) each 10 u.60.21 6 a one way switch ( make: anchor woods ) each 150 v.60.22 6 a 3 pin shuttered socket ( make: anchor woods ) each 100 w. 60.23 16 a one way switch ( make: anchor woods ) each 150 x.60.24 16 a 5 / 6 pin shuttered socket ( make: anchor woods ) each 100 y.60.25 5 step fan regulator 1 module ( make: anchor woods ) each 50 z.60.26 6 a one way switch ( make: anchor roma plus ) each 400 aa. 60.27 6 a 3 pin shuttered socket ( make: anchor roma plus ) each 200 bb. 60.28 16 a one way switch ( make: anchor roma plus ) each 400 cc. 60.29 16 a 5 / 6 pin shuttered socket ( make: anchor roma plus ) each 200 dd. 60.30 5 step fan regulator 1 module ( make: anchor roma plus ) each 50 ee. 60.31 supply of mounting grid plates with cover plates 4 module ( make: anchor roma plus suitable for anchor roma plus accessories ) each 40 ff. 60.32 supply of mounting grid plates with cover plates 6module ( make: anchor roma plus suitable for anchor roma plus accessories ) each 40 gg. 60.33 supply of mounting grid plates with cover plates 12 module ( make:anchor roma plus suitable for anchor roma plus accessories ) each 40 hh. 60.34 6 a one way switch ( make: anchor penta ) each 25 ii.60.35 6 a 3 pin shuttered socket ( make: anchor penta ) each 10 jj.60.36 16 a one way switch ( make: anchor penta ) each 25 kk. 60.37 16 a 5 / 6 pin shuttered socket ( make: anchor penta ) each 10 ll.60.38 5 step fan regulator 1 module ( make: anchor penta ) each 10 61. supply of hot dip galvanized m.s. box of 20 swg with earthing terminal suitable for modular accessories 4 module each 40 62. supply of hot dip galvanized m.s. box of 20 swg with earthing terminal suitable for modular accessories 6 module each 40 63. supply of hot dip galvanized m.s. box of 20 swg with earthing terminal suitable for modular accessories 12 module each 40 64. supply of of p.v.c. / xlpe insulated & p.v.c. sheathed armoured cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of approved make 6.0 sqmm 2 core ( make : gloster , cci, finolex, rallison, ekta, delton, havells, kei, paramount, worldcab, diatron, unicab, unistar, orient cab, empire, orbit, polycab, national ) mtr. 500 65. supply of of p.v.c. / xlpe insulated & p.v.c. sheathed armoured cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of approved make 6.0 sqmm 4 core ( make : gloster , cci, finolex, rallison, ekta, delton, havells, kei, paramount, worldcab, diatron, unicab, unistar, orient cab, empire, orbit, polycab, national ) mtr. 500 66. supply of of p.v.c. / xlpe insulated & p.v.c. sheathed armoured cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of approved make 10.0 sqmm 4 core ( make rr kabel, national, finolex ) mtr. 800 67. supply of of p.v.c. / xlpe insulated & p.v.c. sheathed armoured cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of approved make 35.0 sqmm 4 core ( make : gloster , cci, finolex, rallison, ekta, delton, havells, kei, paramount, worldcab, diatron, unicab, unistar, orient cab, empire, orbit, polycab, national ) mtr. 400 68. supply of heavy duty horizontal type sheet steel distribution board phophatised / powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar, masking sheet, conforming to is13032 & is8623 double door ( single phase ) 6 way ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 16 69. supply of heavy duty horizontal type sheet steel distribution board phophatised / powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar, masking sheet, conforming to is13032 & is8623 double door ( three phase ) 4 way ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 4.0 70. supply of heavy duty horizontal type sheet steel distribution board phophatised / powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar, masking sheet, conforming to is13032 & each 4.0 is8623 double door ( three phase ) 6 way ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) 71. supply of heavy duty sheet steel end box for distribution board duly phophatised powder coated complete as required for tpn 4 way db ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 10 72. supply of recessed / surface mounting heavy duty vertical type 16 swg sheet steel distribution board with provision of incomer suitable for mccb and sp / tp mcb as outgoing , phophatised , powder painted complete with insulated suitable rating copper bus bar , neutral link, earth link and din bar, masking sheet & conforming to is13032 & is8623 6 way double door with provision of incomer mccb 100a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 2 73. supply of recessed / surface mounting heavy duty vertical type 16 swg sheet steel distribution board with provision of incomer suitable for mccb and sp / tp mcb as outgoing , phophatised , powder painted complete with insulated suitable rating copper bus bar , neutral link, earth link and din bar, masking sheet & conforming to is13032 & is8623 8 way double door with provision of incomer mccb 100 a rating ( make: schneider ( neo break ) , siemens, hpl, ge , standard, indoasian ( gold ) , havells, c & s, abb ( s270 ) , l&t, legrand ( ekinoxe / lexic ) ) each 4 74. supply of quick make and quick break 4 pole current limiting mccb having following current rating, short circuit breaking capacity at 440 / 415 v, 50 hz; o / l & s / c settings and conforming to is 60947 2 / iec 60947 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for uvr , shunt trip , earth fault trip, push ( test ) to trip. 100 amp , 16 ka, adjustable o / l & fixed s / c setting, ics = 100 % icu with thermal magnetic release ( make :abb, siemens, ge, l&t, schneider, legrand, c&s, hpl, indoasian, bch ) each 10 75. exhaust fan ( double ball bearing, capacitor start single phase metallic blade fresh air fan ) 300 mm ( make : almonard, cg, alstom, khaitan, usha, havells ) nos. 40 76. supply of air circulator wall fan 450 mm 3 blade, aluminium alloy one piece blade, double ball bearing 90 degree oscillation, three speed, 230 volts, 1440 rpm, 100 watts. ( make: almonard, havells, bajaj, crompton, alstom ) nos. 10 77. supply of 250 mm sweep ventilating fans, capacitor start, single phase with pvc impeller, abs body, automatic openable louver shutter ( make: almonard, havells, bajaj, crompton, alstom ) nos. 50 78. supply of ip40 led recessed, round non dimmable led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal / external bis complience 2.5kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and incompliance to iec standards. system lumen efficacy of ≥ 120lm / watt, thd<10%, p.f.≥0.95, cri>80, life time of minimum 50000 burning hourswith, 70% of intial lumen maintaned till life ends, cct 6000°k , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. nos. 60 15 watts round 6 dia recessed led down ligther ( make : cg, bajaj, wipro, surya, havells, hpl, ge, pierlite, halonixphilips, cg, bajaj, wipro, surya, havells ) 79. supply of box type t 5 tube fitting fabricated from polycarbonate complete with accessories electronic choke with terminal block duly prewired with copper conductor including making connection ( with tube ) . 1 x 28 watts with eb ( make : cg, bajaj, wipro, surya, havells, hpl, ge, pierlite, halonixphilips, cg, bajaj, wipro, surya, havell...

Ministry Of Railways - Rajasthan

33006531 bids are invited for air circulator type electric fan as per is 2997auto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes. ( a maximum of300 times ) mse total quantity : 6...

Department Of Atomic Energy - Rajasthan

32601173 bids are invited for table fan / wall mount fan / ceiling mount fan as per is 555 (q3) , electric ceiling type fans as per is 374 (q3) , air circulator type electric fan as per is 2997(q3) , propeller type ac ventilating fan exhaust as per2312 (q3) total quantity : 65...

Military Engineer Services - Rajasthan

32095867 repair maintenance of summer appliance i e water cooler desert cooler ac refrigerator and deep freezers and repair overhauling of ceiling fans exhaust fans geysers air circulator fresh air fan etc at military station kanasar repair maintenance of summer appliance i e water cooler desert cooler ac refrigerator and deep freezers and repair overhauling of ceiling fans exhaust fans geysers air circulator fresh air fan etc at military station kanasar...

Indian Army - Rajasthan

31263274 bids are invited for steel body evaporative coolers desert cooler (q3) , split air conditioner including green ac (q2) , automatic line voltage corrector or step type auto transformer (q3) , domestic water heater geyser as per is 2082 (q3) ,propeller type ac ventilating fan exhaust as per 2312 (q3), air circulator type electric fan as per is 2997 (q3), wall fan (q3) total quantity : 243...

Military Engineer Services - Rajasthan

30201995 repair and maint of ceiling fans, air circulators, exhaust fans, geyser and solar water heater under ge ( s ) jaipur repair and maint of ceiling fans, air circulators, exhaust fans, geyser and solar water heater under ge ( s ) jaipur...

Military Engineer Services - Rajasthan

30190786 repair and maint of ceiling fans, air circulators, exhaust repair and maint of ceiling fans, air circulators, exhaust fans, geyser and solar water heater under ge ( s ) jaipur...

North Western Railway - Rajasthan

30065508 supply of supply of heavy duty bldc air circulator fan 600 mmsupply of heavy duty bldc air circulator fan 600 mm,supply of heavy duty bldc air circulator fan 600 mm sweep(24 inch), 1300 rpm (+/ 5%),watt 120 140w, wall mounting type should have speed adjustments, suitable to work on 200 260v ac, 50 hz supply,air delivery: minimum of 500 cmm, conforming to is 2997/1964 with two years warranty. accepted make: airzon,havells, bajaj, atomberg or equivalent....