40343943
various work for arrangement of assembly election 2023 at rajasthan college and commerce college, jaipur 2 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75 cement mortar 1 : 3 ( 1 cement : 3 coarse sand ) 3 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 4 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish 20mm thick . 5 providing and fixing double scaffolding system on the exterior side, upto five story made with 4 wooden member 1.5 m c / c horizontal and vertical direction joining with rassi, clamps, challies. the scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safty features for the workmen etc complete as per direction of ei.the lavation area of the scaffolding shall be measured for payment. the payment will be made once irrespective of duration of scaffolding.note : this item to be used for maintence work judicially 6 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 7 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. in cement mortar. 8 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead with cement mortar 1 :4 ( 1 cement : 4 coarse sand ) 9 patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. 10 making of hole ( width up to 150 mm ) in r.c.c. slab / wall / beams by power driven drilling machine complete as per direction of ei upto 150mm thick 11 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size ) . 12 repair to stone masonary in cement sand mortar 1:6 with old and new stone. 13 rough chisel dressed kota stone 35 mm thick flooring of approved shade set in pattern over 20mm thick base of cement mortar 1:6 ( 1 cement : 6 coarse sand ) and pointingwith cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects : 14 cement plaster 1:3 under old stone slabs with admixture ( gur, nails, binding wire to mesh and scraping scales & dressing joints of slabs complete. proofing above 25 mm thickness& upto 60 mm thickness 15 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying first layer of slurry of cement @ 0.488 kg / sqm mixed with water proofing cement compound @0.253 kg / / sqm .this layer will be allowed to air cure for 4 hours. second layer of slurryof cement @ 0.242 kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm this layer will be allowed to air cure for4 hours followed by water curing for 48 hours. the rates includes preparation of surface treatment & sealing of all joints , corners, junction with polymer mixed slurry. 16 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) . 17 providing and laying ofpaver block as per is 15658 : 2006 ( indian standard for precast concrete block for paving specification ) and irc : sp:63 2004 ( guidelines for the use of interlocking concrete block pavement ) m 30, 60 mm thick to be used in non traffic areas like building premises, monument premises, land scapes, public gardens / park, domestic drives, paths and patios, embankment slopes, sand stabilization area etc. ( as per table 1 ofis 15658:2006 category‘b’ denated only two side like i, z, t shape etc. as per irc sp 63:2004 18 earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 sqm on plan including disposal of excavated earth up to 50 mtr. and lift up to 1.5 mtr. disposed soil to be levelled and neatly dressed : all kinds of soil 19 surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead up to 50 mtr. and lift up to 1.5 mtr. : all kinds of soil 20 providing & laying tactile tile ( for vision impaired persons is standard of size 300x300x20mm and confirming to is 1231 of 1980 ( re affirmed in 2006 ) in all colours & sheds further product should confirm astm 303 for shad resistance and din51099 for colour fastness etc. laid on 20mm thick base of cement mortar 1:4 ( 1 cement : 4 course sand ) in all shapes & patterns including grouting the joint which white cement mixer ) will matching pigments etc complete is per direction of engineer in charges. grade m 30 21 providing and fixing designer cement concrete polished tiles over 20mm average thick base of cm 1 :4 ( 1 cement : 4 sand ) jointing with cement mortar 1 :2 ( 1cement : 2 sand ) with pigment to match the shade of the tiles having minimum thickness of 25mm complete with all respect. ( as per is 1237:2012 ) 22 chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles includingrubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand ) dark shade using ordinary cement. 23 supply of beldar 24 carriage of building earth, sand, lime, morrum manure or sludge including loading and unloading with all lead. 25 carriage of building rubbish stone metal ( grit and ballast etc. ) including loading and unloading with all lead. 26 part : b : joinery work 27 labour charges for repair to door / window without using any material such as applying randha ( finishing ) tightening of bolts & screw etc. 28 repairofdoor, windowshuttersincludingcostofmaterialandlabourforchangeofdamaged : 29 panel by shuttering ply 9mm thick ( commercial ) 30 panel by wire gauge 14 mesh x 24 gauge 31 aldrop of mild steel 12 long x12mm dia 32 steel hinges for wooden chowkhat 4 size 33 mild steel tower bolt 6 long 34 steel locking bolt 35 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a30 mm thick . commercial veneer both side 36 extra for providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters ( over all area of door shutter to be measured ) over item no. 8.13. 37 providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebates to be measured ) . panelling for panelled and glazed shutter 25 mm to 40 mm thick is 710 1976 marked 19 mm thick commerical ply 38 renewing glass panes with wooden fillets wherever necessary4mm thick plain glass panes. 39 providing and fixing is : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. 40 providing and fixing s.s. rod 30mm dia ( 304 grade , 16swg ) includingbrackets fixed with c.p. brass screws and rawl plugs, etc., wherever necessary complete two side central all fittings. 41 providing and fixing 12 mm thick prelaminated three layer medium density ( exterior grade ) particle board grade i, type ii conforming to is : 12823 bonded formaldehyde synthetic resin , of approved brand and manufacture in paneling fixed in aluminium doors , windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer in charge. pre laminatedparticleboardwithdecorativelaminationononesideandbalancinglaminationonotherside. 42 providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge. ( cost of aluminium snap beading shall be paid in basicitem. ) with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg / sqm ) 43 providing and fixing 100mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete. 44 providing and fixing aluminium u shape handle of size 100mm with ss screws etc. complete as per direction of engineer in chargepowder coated minimum thickness 50 micron aluminium 45 providing and fixingaluminum workfor doors , windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285, fixed with rawl plugs and screws or with fixing clips , or with expansion hold fasteners including necessary filling up of gap. at junctions , at top , bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth , rust free, straight , mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing / paneling , c.p. brass / stainless steel screws al. tower bolt & al. handle & al. aldrop etc., all complete as per architectural drawings and thedirections of engineer in – charge . ( glazing and paneling to be paid for separately ) . 46 for fixed portionpowder coating aluminum ( minimum thickness of powder coating 50 micron ) 47 for shutters builtup standard tubular sections of openable doors , windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required ( lockes shall be paid for separately ) .powder coating aluminum ( minimum thickness of powder coating 50 micron ) 48 supplying and fixing rollor blinds of good quality and approved make made out of imported fabric including roller mechanism and lock with chain system with all necessary hooks etc. complete as per direction and sample approved by engineer in charge. 49 labour charges for removing and refixing aluminium partitions door including minor repair on alterationin the same. 50 providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . grade 304 51 part : c : steel work 52 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 53 providing and fixing m.s. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit corrosive red oxide primer paint 54 supplying and fixing of chain link fencing with angle iron posts 50x50x6mm placed at every 3 mtr. apart 30cm in ground embedded in cement concrete 1:3:6 ( 30x30x45cm ) corner and every tenth post to be strutted with ( 50 x 50 x 6cm ) angle iron provided and fixed and fitted with posts including earth work in excavation etc. complete with chain link size. 50mm x 50mm x 3.15mm 55 providing and fixing welded mesh / expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete ( excluding frame work ) of size. welded mesh 25 mmx 25 mm x 2.1 mm 56 repair of existing steel glazed doors, windows and ventilator, ms sheet door, garge doors, compound wall gates etc. by welding drilling complete include. cost of welding rods and hire charge of welding meachine and tp etc complete 57 l / c for fixing of gi / ac sheet include. cutting jhiri and repair , cutting of sheet , fixing of sheet with j or l hook and bitumen washer as per direction of ei 58 supply and installation of multi rib proofing / cladding sheet manufacture out of0.50mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel ( as per 150gsm zinc aluminum coated 550mpa tuekd strength ) confirming to is: 1397 / astm a 792 sheet to have wide pens 30mm high nb at 250 centre and centre width of 1020mm sheets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding. 59 part : d : painting work 60 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding old work ( one or more coats ) including scrapping surface andnecessaryrepairs. colour change 61 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding old work ( one or more coats ) 62 painting with synthetic enamel paint of approved brand and manufacture togive an even shade one or more coats on old work. 63 removing dry or oil bound distemper by scrapping sand papering and preparing surface smooth including necessary repairs to scratches by sandla / loi and all scaffolding ( for colour changing only ) 64 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 65 new plastered surface ( three or more coats ) 66 old plastered surface ( two or more coats ) 67 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 68 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provisionold work 69 lettering with black japan paint of approved brand and manufacture. 70 part : e : sanitary work 71 p & f water closet seat covers with brass hinges complete solid pvc ( is 2548 marked ) grade i black for ewc. 72 p & f low level flushing cistern of 10 litres capacity ( is : 2556 mark ) of approved make with complete fittings c.i. brackets duly painted, brass ball cock with ball ( is: 1703 mark ) complete including cutting and making good the wall pvc withpvcbend and superior internal fittings as per is : 7231 . 73 p&fc.p.brassurinalflushpipeset complete with flanged brackets of approved make. for 3 urinals 74 p & f wvc wash basin ( ist quality is:2556 mark ) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock ( is:8934 mark ) & 32 mm c.p. brass waste coupling of approved make, p.v.c waste pipe with pvc nut 32 mm complete including cutting & making good the wall size 580 mm x 450 mm 75 p& f waste coulping with fittings of approved quality / make: c.p brass 40 mm dia 76 p& f waste pipe with all fittingp.v.c. with c.p. nut 40 mm dia 77 p & f looking mirrors with p.v.c. frame of approved make as per direction of engineer in chargeround 500mm dia 78 p & f grating of approved quality / make c.p. brass with frame ( heavy ) & superior quality size 125mm dia. 79 p & f g.i. pipes ( internal work ) with g.i. fittings excluding union ( is:1239 mark ) & ms clamps including cutting and making good the walls and floors: exposed on wall b class 80 15 mm dia nominal bore 81 25mm dia nominal bore 82 p & f pilllar cocks ( is :8931 : 1993 mark ) of superior quality and approved make c.p. pillar cock, 15 mm dia nominal bore 83 p & f bib cock ( is : 8931 mark ) , superior quality of approved make c.p. brass bib cock, 15mm nominal bore. 84 p & f ball cock ( is :1703 mark ) with rod& p.v.c. ball complete brass wt. not less than 300 gm, 15mm. 85 p & f inlet connection ( angle valves ) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection with 37 cm long pipe and nut. 86 p & f full way valve ( is:778 mark ) or wheel valve of approved make : 87 gun metal 15mm nominal bore. 88 gun metal 25mm nominal bore. 89 gun metal 40mm nominal bore. 90 providing and fixing unplasticized poly vinyl chloride ( upvc ) swr pipes type b for sciland waste discharge system ( is:13592 : 1992 marked ) of approved quality / make 110 mm dia 91 providing and fixing unplasticized poly vinyl chloride ( upvc ) swr pipes fittings type b for sciland waste discharge system ( is:13592 : 1992 marked ) of approved quality / make door bend 87.5 dg. 110mm dia 92 mechanised cleaning of sewer line of diameter upto 200mm with the help of trolley mounted electrical driven machine having flexible steel springs of length 20ft. each which are rotated with the help of electric motor and clutch assembly. 93 repairing ofcement concrete chambers of different size as per requirement at site and as per direction of engineer in charge. 94 supplying & fixing r.c.c. manholes covers with frame of approved make ( light duty ) . size 500mm dia ( double seal ) 95 supplyingandfixingferro cementcoverwithc.i.frameforchambers&manholes of size. 96 450mm dia, 5kg. c.i. frameto with stand 3 mt center point load & minimum unfracturedload of 1 mt. ( light duty ) .a 97 500mm dia 12 kg. do 15 mt centre point load ( medium duty ) . 98 raising manhole cover and frames slab to required level including dismantling existing slab and making good the damage as required ( raising depth of manhole masonry to be paid separately ) . rectangular manhole 90x60 cm 99 p & f european type white glazed vitreous china 1st quality w.c pan ( is : 2556 mark ) with p or s trap including cutting and making good the wall and floor 100 p & f lst quality wvc urinal ( is:2556 mark ) with 25mm dia g.i. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. flat back ( large ) or half stall size 610x400x80mm. 101 p&f marble urinal partition slab both sides polished of approved design cut from marble size 900x600mm. makrana ii quality marble having light spots 102 labourchargesforremovingandrefixingofurinals ( alltype&sizes ) includingall necessary fittings. 103 p & f c.p. brass urinal spreader for stall urinal of approved make. 104 p & f plastic syphon of approved make for automatic flush tank. 105 removing and re fixing of wash hand basin including all necessary fittings. 106 providing and fixing new spindle for bib cock / pillar cock for repairing purpose to solve leakage and proper functioning of tap. 107 labour charges for removing & refixing the water storage tank of all sizes and including all necessary fitting complete in all respect as per approved sample and direction of engineer in charge. 108 providing and fixing superior quality pvc tank cover complete as per approved by engineer in charge above 500 lt. capacity 109 p & f inlet connection ( angle valves ) superior quality, of approved make, for wash basin, gyser etc. synthetic material ( ptmt ) inlet connection of approved quality / make 15 mm nominal size. 110 p & f 15 mm. dia connection pipe of approved quality / make pvc pipe withc.p. brass nuts upto length, 600mm. 111 p & f pvc storage tank isi marked ( is : 12701 ) indicating thebis license no ) , of approved make with cover, 25mm dia 1m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 112 500 litres capacity. 113 1000 litres capacity. 114 hoisting charges for each floor : 115 upto 750 litres capacity. 116 above 750 litres capacity. 117 providing and fixingsuperior quality cp brassfittings of approved make as per direction of engineer in charge 118 swan neck pillar cock 15 mm nominal size 119 bib cock with long thread 15 mm nominal size 120 long body bib cock 15 mm nominal size 121 angular stop cock with long thread 15 mm nominal size 122 sink cock with swinging casted spout ( table mounted ) 15 mm nominal size 123 600 mm long towel rail 124 revolving type towel ring 125 healthfocet ( premium heavy quality ) as approved by engineer in charge...
Due Date : October 27, 2023
Tender Value : ₹ 53.50 Lakhs
